SRF2019 - List of Keywords (cavity)

Paper	Title	Other Keywords	Page
MOFAA1	LCLS-II: Status, Issues and Plans	SRF, cryomodule, linac, FEL	1
	M.C. Ross SLAC, Menlo Park, California, USA
	Funding: Work supported by Department of Energy contract DE-AC02-76SF00515 The Linac Coherent Light Source II (LCLS-II) project requires the assembly, test, and installation of 37 cryomodules (CM) in order to deliver a 4 GeV CW electron beam to the FEL undulators for production of both hard and soft X-ray pulses at a repetition rate of up to 1 MHz. SRF cavity performance in the 30+ tested CM exceeds gradient and cryogenic dynamic heat-load requirements (set at 16 MV/m and 10 W resp). In this talk we present microphonics, shipping, magnetic-flux exclusion, and field emission performance. The US funding agency, DOE, has recently approved an additional 20 CM for the extension of LCLS-II to 8 GeV. This paper will also include initial cavity and heat-load performance results for the extension project, LCLS-II-HE.
	Slides MOFAA1 [30.146 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOFAA1
About •	paper received ※ 25 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOFAA2	Operation of the European XFEL Towards the Maximum Energy	electron, FEL, operation, MMI	9
	M. Omet, V. Ayvazyan, J. Branlard, S. Choroba, W. Decking, V.V. Katalev, D. Kostin, L. Lilje, P. Morozov, Y. Nachtigal, H. Schlarb, V. Vogel, N. Walker, B. Yildirim DESY, Hamburg, Germany
	After the initial commissioning of the available 25 radio frequency (RF) stations of the European XFEL (RF gun, A1, AH1 and stations A2 through A23) a maximum electron beam energy of 14.5 GeV was achieved, 3 GeV short of the design energy of 17.5 GeV. In order to tackle this problem, the Maximum Gradient Task Force (MGTF) was formed. In the scope of the work of the MGTF, RF stations A6 through A25 (linac L3) were systematically investigated and voltage-limiting factors of the SRF accelerating modules and their RF distribution system were identified and improved. As a result, the design electron beam energy was exceeded at 17.6 GeV on the 18.7.2018. Beside this an overview over the regular RF operation at the European XFEL is given.
	Slides MOFAA2 [5.695 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOFAA2
About •	paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOFAA3	The FRIB SC-Linac - Installation and Phased Commissioning	cryomodule, MMI, linac, cryogenics	12
	J. Wei, H. Ao, S. Beher, B. Bird, N.K. Bultman, F. Casagrande, D. Chabot, W. Chang, S. Cogan, C. Compton, J. Curtin, K.D. Davidson, E. Daykin, K. Elliott, A. Facco, A. Fila, V. Ganni, A. Ganshyn, P.E. Gibson, T. Glasmacher, I. Grender, W. Hartung, L. Hodges, K. Holland, H.-C. Hseuh, A. Hussain, M. Ikegami, S. Jones, T. Kanemura, S.H. Kim, P. Knudsen, M.G. Konrad, J. LeTourneau, Z. Li, S.M. Lidia, G. Machicoane, P. Manwiller, F. Marti, T. Maruta, E.S. Metzgar, S.J. Miller, D.G. Morris, C. Nguyen, K. Openlander, P.N. Ostroumov, A.S. Plastun, J.T. Popielarski, L. Popielarski, J. Priller, M.A. Reaume, H.T. Ren, T. Russo, K. Saito, M. Shuptar, J.W. Stetson, D.R. Victory, R. Walker, X. Wang, J.D. Wenstrom, M. Wright, M. Xu, T. Xu, Y. Yamazaki, Q. Zhao, S. Zhao FRIB, East Lansing, Michigan, USA K. Dixon, M. Wiseman JLab, Newport News, Virginia, USA A. Facco INFN/LNL, Legnaro (PD), Italy K. Hosoyama KEK, Ibaraki, Japan M.P. Kelly ANL, Lemont, Illinois, USA R.E. Laxdal TRIUMF, Vancouver, Canada
	Funding: Work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661. The Facility for Rare Isotope Beams (FRIB) superconducting (SC) driver linac is designed to accelerate all stable ions including uranium to energies above 200 MeV/u primarily with 46 cryomodules containing 324 quarter-wave resonators (QWR) and half-wave (HWR) resonators. With the newly commissioned helium refrigeration system supplying liquid helium to the QWR and solenoids, heavy ion beams including Ne, Ar, Kr and Xe were accelerated to the charge stripper location above 20 MeV/u with the first linac segment consisting of 15 cryomodules containing 10⁴ QWRs of β=0.041 and 0.085 and 39 solenoids. Installation of cryomodules with β=0.29 and 0.53 HWRs is proceeding in parallel. Development of β=0.65 elliptical resonators is on-going supporting the FRIB energy upgrade to 400 MeV/u. This paper summarizes the SC-linac installation and phased commissioning status that is on schedule and on budget to the FRIB project.
	Slides MOFAA3 [46.571 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOFAA3
About •	paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP003	Development of Nb₃Sn Cavity Coating at IMP	niobium, SRF, radio-frequency, experiment	21
	Z.Q. Yang, H. Guo, Y. He, C.L. Li, Z.Q. Lin, M. Lu, T. Tan, P.R. Xiong, S.H. Zhang, S.X. Zhang IMP/CAS, Lanzhou, People’s Republic of China
	The A15 superconductor Nb₃Sn is one of the most promising alternative materials to standard niobium for SRF applications. In this paper, we report our progress in the development of Nb₃Sn cavity coating by vapor diffusion method at IMP. The evolutionary process of nucleation was analyzed. Influence of S_nCl₂ partial pressure inhomogeneity was studied. Less-nuclear zones were found on the surfaces of nucleation samples. The Nb₃Sn film structure and composition were investigated and analyzed. In light of knowledge obtained above, the coating process was optimized. Finally, both 1.3 GHz and 650 MHz single cell cavities were coated and vertically tested both at 4 K and 2 K. Effect of low temperature baking (1000°C for 48 hs) on the RF performance of Nb₃Sn cavity was studied. After baking, the Q drop in the low field region was eliminated and the Q in the intermediate field region was increased 8 times. The Q was 10 times larger than that of the Nb cavity at 4.2 K even in the case of the ambient field larger than 20 mGs. This study shows that the low temperature baking is an effective enrichment to the post treatment of the Nb₃Sn cavity.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP003
About •	paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP005	The Facility for Rare Isotope Beams Superconducting Cavity Production Status and Findings Concerning Surface Defects	linac, SRF, niobium, status	31
	C. Compton NSCL, East Lansing, Michigan, USA H. Ao, J. Asciutto, K. Elliott, W. Hartung, S.H. Kim, E.S. Metzgar, S.J. Miller, J.T. Popielarski, L. Popielarski, K. Saito, T. Xu FRIB, East Lansing, Michigan, USA J. Craft SLAC, Menlo Park, California, USA
	Funding: This material is based upon work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661 The Facility for Rare Isotope Beams (FRIB), located on the campus of Michigan State University (MSU) will require 324 Superconducting Radio Frequency (SRF) cavities in the driver linac. Four types of cavities of two classes, quarter-wave (β=0.041 and 0.085) and half-wave (β=0.29 and 0.53), will be housed in 46 cryomodules. To date, FRIB has tested over 300 cavities in vertical Dewar tests as part of the certification procedures. Incoming cavities, fabricated in industry, are sequenced through acceptance inspection and checked for non-conformance. If accepted, the cavities are processed, assembled onto a vertical test stand, and cold tested. A large database of cavity surface images has been collected with the aid of a borescope camera. Borescope inspection is a standard step that is performed at incoming inspection, post-acid bulk etch, and after failed tests (if necessary) for each cavity, in order to locate any non-conformances. Findings of surface defects relating to degraded cavity performance will be presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP005
About •	paper received ※ 02 July 2019 paper accepted ※ 13 August 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP007	400 MHz Seamless Copper Cavity in the Framework of FCC Study	ISOL, superconductivity, framework, status	36
	O. Azzolini, G. Keppel, C. Pira INFN/LNL, Legnaro (PD), Italy
	In the framework of the FCC study the production of 400 MHz copper cavities is one of the key challenges for the development of more efficient superconducting RF cavities. Any progress on substrate manufacturing and preparation will have an immediate impact on the final RF performance, as it was demonstrated by the seamless cavities produced for the HIE-ISOLDE project. Spinning is a potential alternative to conventional production methods of copper single and multi-cells. In this work is presented the first 400 MHz copper SRF cavity prototype produced via Spinning at Laboratori Nazionali di Legnaro of INFN. The production process is explained starting from a copper foil of 1000 mm diameter and 4mm thick to arrive to a seamless 400 MHz cavity. Moreover, the metrology of the cavity and the analysis of the influence of intermediate thermal treatments among each steps of cold work are shown.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP007
About •	paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP010	Ab Initio Calculations on the Growth and Superconducting Properties of Nb₃Sn	site, niobium, SRF, electron	39
	N. Sitaraman, T. Arias, P. Cueva, M.M. Kelley, D.A. Muller Cornell University, Ithaca, New York, USA J.M. Carlson, A.R. Pack, M.K. Transtrum Brigham Young University, Provo, USA M. Liepe, R.D. Porter, Z. Sun Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
	Funding: This research was funded by the Center for Bright Beams. In this work, we employ theoretical ab initio techniques to solve mysteries and gain new insights in Nb₃Sn SRF physics. We determine the temperature dependence of Nb₃Sn antisite defect formation energies, and discuss the implications of these results for defect segregation. We calculate the phonon spectral function for Nb₃Sn cells with different combinations of antisite defects and use these results to determine Tc as a function of stoichiometry. These results allow for the first-ever determination of Tc in the tin-rich regime, where experimental measurements are unavailable and which is critical to understanding the impact of tin-rich grain boundaries on superconducting cavity performance. Finally, we propose a theory for the growth mechanism of Nb₃Sn growth on a thick oxide, explaining the puzzling disappearing droplet behavior of Sn on Nb oxide and suggesting how in general an oxide layer reacts with Sn to produce a uniform Nb₃Sn layer.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP010
About •	paper received ※ 02 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP011	High Frequency Nb₃Sn Cavities	SRF, niobium, radio-frequency, factory	44
	R.D. Porter, M. Liepe, J.T. Maniscalco Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
	Niobium-3 Tin (Nb₃Sn) is an alternative material to Nb for SRF cavities. This material is capable of higher temperature operation and has high theoretical maximum accelerating gradients. Cornell University is a leader in the development of this material for SRF applications, and current Nb₃Sn 1.3 GHz single cells produced at Cornell achieve quality factors above 10^zEhNZeHn at 4.2 K at medium fields, far above what can be reached with niobium. Most of the recent Nb₃Sn cavity development has been done at 1.3 GHz. In this paper, we present new results from Nb₃Sn cavities at 2.6 GHz and 3.9 GHz. We compare relative cavity performance and flux trapping sensitivities, and extract frequency dependencies. Results show that the frequency can be increased without degrading the performance of the cavities, opening the path towards a new generation of compact and efficient SRF cavities for a wide range of future applications.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP011
About •	paper received ※ 05 July 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP013	Reducing Surface Roughness of Nb₃Sn Through Chemical Polishing Treatments	niobium, superconductivity, controls, SRF	48
	H. Hu, M. Liepe, R.D. Porter Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
	Niobium-3 tin (Nb₃Sn) is a promising alternative material for SRF cavities, with theoretical limits for critical temperatures and superheating fields reaching twice that of conventional Nb cavities. However, currently achievable accelerating gradients in Nb₃Sn cavities are much lower than their theoretical limit. One limitation to the maximum accelerating gradient is surface magnetic field enhancement caused by the surface roughness of Nb₃Sn. However, there are currently no standard techniques used to reduce Nb₃Sn surface roughness. Since Nb₃Sn is only 2-3 microns thick, it is difficult to selectively polish Nb₃Sn without removing the entire layer. Here, we investigate reducing the surface roughness of Nb₃Sn through applying chemical polishing treatments, including modified versions of standard techniques such as Buffered Chemical Polishing (BCP) and Electropolishing (EP). Through data acquired from Atomic Force Microscope (AFM) scans, SEM scans, and SEM-EDS analysis, we show the effects of these chemical treatments in reducing surface roughness and consider the changes in the chemical composition of Nb₃Sn that may occur through the etching process. We find that BCP with a 1:1:8 solution is ineffective while EP halves the surface roughness of Nb₃Sn.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP013
About •	paper received ※ 01 July 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP014	Electroplating of Sn Film on Nb Substrate for Generating Nb₃Sn Thin Films and Post Laser Annealing	laser, radio-frequency, electron, HOM	51
	Z. Sun, M. Liepe, T.E. Oseroff, R.D. Porter Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA T. Arias, A.B. Connolly, J.M. Scholtz, N. Sitaraman, M.O. Thompson Cornell University, Ithaca, New York, USA X. Deng University of Virginia, Charlottesville, Virginia, USA K.D. Dobson University of Delaware, Newark, Delaware, USA
	Controlling film quality of Nb₃Sn is critical to its SRF cavity performance. The state-of-the-art vapor diffusion approach for Nb₃Sn deposition observed surface roughness, thin grain regions, and misfit dislocations which negatively affect the RF performance. The Sn deficiency and non-uniformity at the nucleation stage of vapor deposition is believed to be the fundamental reason to cause these roughness and defects issues. Thus, we propose to pre-deposit a uniform Sn film on the Nb substrate, which is able to provide sufficient Sn source during the following heat treatment for Nb₃Sn nucleation and growth. Here, we demonstrated successful electrodeposition of a low-roughness, dendrite-free, excellent-adhesion Sn film on the Nb substrate. More importantly, we further achieved a uniform, low-roughness (Ra = 66 nm), pure-stoichiometric Nb₃Sn film through thermal treatment of this electroplated Sn film in the furnace. Additionally, we provide preliminary results of laser annealing as a post treatment for epitaxial grain growth and roughness reduction.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP014
About •	paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP015	RF Performance Sensitivity to Tuning of Nb₃Sn Coated CEBAF Cavities	simulation, SRF, experiment, factory	55
	G.V. Eremeev, W. Crahen, J. Henry, F. Marhauser, C.E. Reece JLab, Newport News, Virginia, USA U. Pudasaini The College of William and Mary, Williamsburg, Virginia, USA
	Funding: Co-Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. Based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics. Nb₃Sn has the potential to surpass niobium as the material of choice for SRF applications. The potential of this material stems from a larger superconducting energy gap, which leads to expectations of a higher RF critical field and a lower RF surface resistance. The appeal of better superconducting properties is offset by the relative complexity of producing practical Nb₃Sn structures, and Nb₃Sn sensitivity to lattice disorder challenges the use of the material for practical applications. Such sensitivity is indirectly probed during SRF cavity development, when the cavity is tuned to match the desired accelerator frequency. In the course of recent experiments we have coated and tuned several multi-cell cavities. Cold RF measurements before and after tuning showed degradation in cavity performance after tuning. The results of RF measurement were compared against strain evolution on Nb₃Sn surface during tuning based on CST and ANSYS models.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP015
About •	paper received ※ 26 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP016	Insights Into Nb₃Sn Coating of CEBAF Cavities From Witness Sample Analysis	niobium, SRF, HOM, hardware	60
	G.V. Eremeev, M.J. Kelley, C.E. Reece JLab, Newport News, Virginia, USA M.J. Kelley, U. Pudasaini The College of William and Mary, Williamsburg, Virginia, USA
	Funding: Co-Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. Based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics. With the progress made in the Nb₃Sn coatings on single-cell SRF cavities, development is ongoing to reproduce single-cell cavity results on practical structures such as CEBAF 5-cell cavities. During CEBAF cavity coating development, several changes from the single-cell procedure to the coating setup and the heating profile were introduced to improve the quality of Nb₃Sn films. To witness the properties of grown Nb₃Sn films in different cavity locations, 10 mm x 10 mm samples were positioned in strategic places within the coating chamber. Composition and structure of the samples were analyzed with surface analytic techniques and correlated with sample location during coatings. Implications from sample analysis to Nb₃Sn coatings on different geometries are discussed in this contribution.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP016
About •	paper received ※ 26 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP018	Recent Results From Nb₃Sn Single Cell Cavities Coated at Jefferson Lab	SRF, experiment, factory, niobium	65
	U. Pudasaini, M.J. Kelley The College of William and Mary, Williamsburg, Virginia, USA G. Ciovati, G.V. Eremeev, M.J. Kelley, C.E. Reece JLab, Newport News, Virginia, USA I.P. Parajuli, Md.N. Sayeed ODU, Norfolk, Virginia, USA
	Funding: Partially authored by Jefferson Science Associates under contract no. DE¬AC05¬06OR23177. Supported by Office of High Energy Physics under grants DE-SC-0014475 to the College of William and DE-SC-0018918 to Virginia Tech Because of superior superconducting properties (Tc ~ 18.3K, Hs h ~ 425 mT and delta ~ 3.1 meV) compared to niobium, Nb₃Sn promise better RF performance (Q₀ and E_acc) and/or higher operating temperature (2 K Vs 4.2 K) for SRF cavities. Nb₃Sn-coated SRF cavities are produced routinely by depositing a few micron-thick Nb₃Sn films on the interior surface of Nb cavities via tin vapor diffusion technique. Early results from Nb₃Sn cavities coated with this technique exhibited precipi-tous low field Q-slope, also known as Wuppertal slope. Several Nb₃Sn single cell cavities coated at JLab ap-peared to exhibit similar Q-slope. RF testing of cavi-ties and materials study of witness samples were con-tinuously used to modify the coating protocol. At best condition, we were able to produce Nb₃Sn cavity with Q₀ in excess of ~ 5×10¹⁰ at 2 K and ~ 2×1010 at 4 K up the accelerating gradient of ~15 MV/m, without any significant Q-slope. In this presentation, we will dis-cuss recent results from several Nb₃Sn coated single-cell cavities linked with material studies of witness samples, coating process modifications and the possi-ble causative factors to Wuppertal slope.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP018
About •	paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP019	Surface Preparation and Optimization of SC CH Cavities	operation, linac, coupling, ECR	71
	P. Müller, M. Basten, M. Busch, T. Conrad, H. Podlech IAP, Frankfurt am Main, Germany K. Aulenbacher, F.D. Dziuba, M. Miski-Oglu HIM, Mainz, Germany W.A. Barth GSI, Darmstadt, Germany
	The Institute of Applied Physics (IAP) introduced the superconducting multi-gap CH-structure, which is mainly designed for low beta hadron acceleration. In 2017, a 217 MHz sc CH-structure was successfully tested with beam at GSI and multiple CH-structures are currently under development for the GSI cw linac. RF performance of all sc cavities are limited by the surface properties of the used material. Therefore, sufficient surface preparation and optimization is necessary to achieve optimal performance. Presently as standard procedure BCP and HPR is used for CH-cavities. Several surface treatments will be applied to the very first CH-prototype, a 360 MHz, 19-cell cavity. Prior to the first treatment, the status of the cavity was examined, including leak tests and performance tests at 4 and 2 K. This paper presents the performance development of a sc CH cavity depending on different preparation methods.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP019
About •	paper received ※ 23 June 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP022	Superconducting RF Cavity Materials Research at the S-DALINAC	niobium, linac, SRF, simulation	74
	R. Grewe, L. Alff, M. Arnold, J. Conrad, S. Flege, M. Major, N. Pietralla TU Darmstadt, Darmstadt, Germany F. Hug IKP, Mainz, Germany
	Funding: Supported by BMBF Through 05H18RDRB2 Current state-of-the-art superconducting rf (srf) accelerators are mostly using cavities made of high RRR bulk niobium (Nb). The maximum field gradients and quality factors (Q₀) of these cavities are basically reached now. To further increase the srf cavity properties for future accelerator facilities, research of new materials for srf cavity applications is necessary. The current research at the S-DALINAC* is focused on the development of bake-out procedures of Nb samples and cavities in nitrogen (N) atmosphere of up to 100 mbar to nucleate the delta-phase (d-phase) of the Nb-N binary system. The d-phase has superconducting properties which exceed the properties of bulk Nb. This makes the d-phase attractive for srf applications. The vertical test cryostat (vt) at the S-DALINAC has been upgraded and recommissioned to allow investigations of the quality factor and accelerating field gradients of cavities before and after bake-out. The vt upgrade includes a newly developed variable input coupling to allow matching of the external q-factor (Qex) to Q₀. The results of the ongoing research of the nitrogen atmosphere bake-out procedures and the upgrade of the vt will be presented. *N. Pietralla, Nuclear Physics News, Vol. 28, No. 2, 4 (2018)
	Poster MOP022 [1.759 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP022
About •	paper received ※ 21 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP023	Nitrogen Infusion Sample R&D at DESY	niobium, vacuum, SRF, HOM	77
	C. Bate, A. Dangwal Pandey, A. Ermakov, B. Foster, T.F. Keller, D. Reschke, J. Schaffran, S. Sievers, N. Walker, H. Weise, M. Wenskat DESY, Hamburg, Germany W. Hillert University of Hamburg, Institut für Experimentalphysik, Hamburg, Germany G.D.L. Semione, V. Vonk DESY Nanolab, FS-NL, Hamburg, Germany A. Stierle University of Hamburg, Hamburg, Germany
	The European XFEL continuous wave upgrade requires cavities with reduced surface resistance (high Q-values) for high duty cycle while maintaining high accelerating gradient for short-pulse operation. A possible way to meet the requirements is the so-called nitrogen infusion procedure. However, a fundamental understanding and a theoretical model of this method are still missing. The approach shown here is based on sample R&D, with the goal to identify key parameters of the process and establish a stable, reproducible recipe. To understand the underlying processes of the surface evolution, which gives improved cavity performance, advanced surface analysis techniques (e.g. SEM/EDX, TEM, XPS, TOF-SIMS) are utilized. Additionally, a small furnace just for samples was set up to change and explore the parameter space of the infusion recipe. Results of these analyses, their implications for the cavity R&D and next steps are presented.
	Poster MOP023 [3.759 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP023
About •	paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP024	Vacancy-Hydrogen Dynamics in Samples During Low Temperature Baking	positron, niobium, lattice, electron	83
	M. Wenskat, C. Bate, D. Reschke, H. Weise DESY, Hamburg, Germany C. Bate University of Hamburg, Hamburg, Germany M. Butterling, E. Hirschmann, M.O. Liedke, A. Wagner HZDR, Dresden, Germany J. Cizek Charles University, Prague, Czech Republic
	Funding: This work was supported by the Helmholtz Association within the topic Accelerator Research and Development (ARD) of the Matter and Technologies (MT) Program and by the BMBF under the research grant 05H18GURB1. The recent discovery of a modified low temperature baking process lead to a reduction of surface losses and an increase of the accelerating gradient of TESLA shape cavities. The hypothesis linking the accelerator performance and the treatment is the suppression of lossy nanohydrides via defect trapping, with vacancy-hydrogen complexes forming at the lower temperatures. Utilizing Doppler broadening Positron Annihilation Spectroscopy and Positron Annihilation Lifetime Spectroscopy samples made from European XFEL niobium sheets and cavity cut-outs were investigated. The evolution of vacancies, hydrogen and their interaction at different temperature levels have been studied during in-situ annealing. Measurements of niobium samples and a correlation between RF, material properties, and V-H distribution in cavity cut-outs has been done.
	Poster MOP024 [1.087 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP024
About •	paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP025	Cavity Cut-out Studies of a 1.3 GHz Single-cell Cavity After a Failed Nitrogen Infusion Process	niobium, SRF, electron, superconductivity	87
	M. Wenskat, C. Bate, T.F. Keller, D. Reschke DESY, Hamburg, Germany C. Bate University of Hamburg, Hamburg, Germany A. Jeromin DESY Nanolab, FS-NL, Hamburg, Germany J. Knobloch, F. Kramer, O. Kugeler, J.M. Köszegi HZB, Berlin, Germany J. Knobloch University of Siegen, Siegen, Germany
	Funding: This work was supported by the Helmholtz Association within the topic Accelerator Research and Development (ARD) of the Matter and Technologies (MT) Program and by the BMBF under the research grant 05H18GURB1. R&D on the nitrogen infusion process at DESY produced at the beginning a series of 1.3 GHz single-cell cavities which have shown severe deterioration in the vertical cold test which was completely unexpected and could not be explained. To investigate the reason for the deterioration, one of those cavities was optically inspected and a T- and H-Map test was done in collaboration with HZB. Together with 2nd Sound data, regions of interests were identified and cut from the cavity. Subsequent surface analysis techniques (SEM/EDX, SIMS, PIXE, EBSD, DB-PAS, PALS, XPS) were applied in order to identify the reason for the deterioration. Especially the differences between hot and cold spots as well as quench spots identified by T-Mapping were investigated.
	Poster MOP025 [0.975 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP025
About •	paper received ※ 20 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP026	A Cross-Lab Qualification of Modified 120°C Baked Cavities	shielding, multipactoring, factory, niobium	90
	M. Wenskat, D. Reschke, J. Schaffran, L. Steder, M. Wiencek DESY, Hamburg, Germany D. Bafia, A. Grassellino, O.S. Melnychuk Fermilab, Batavia, Illinois, USA A.D. Palczewski JLab, Newport News, Virginia, USA M. Wiencek IFJ-PAN, Kraków, Poland
	Funding: This work was supported by the Helmholtz Association within the topic Accelerator Research and Development (ARD) of the Matter and Technologies (MT) Program and by the BMBF under the research grant 05H18GURB1. Within a global effort to understand and standardize the nitrogen-infusion and the low T bake procedure, one large grain and two fine grain single-cell cavity were treated and tested at FNAL and then send to other labs including DESY and JLab for further studies.
	Poster MOP026 [0.813 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP026
About •	paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP027	Study on Nitrogen Infusion using KEK New Furnace	injection, SRF, accelerating-gradient, vacuum	95
	K. Umemori, E. Kako, T. Konomi, S. Michizono, H. Sakai KEK, Ibaraki, Japan T. Okada Sokendai, Ibaraki, Japan J. Tamura JAEA/J-PARC, Tokai-mura, Japan
	KEK has been carried out high-Q/high-G R&D, to realize high performance of SRF cavities toward ILC. KEK constructed a new furnace, which is dedicated for N-infusion studies. We performed more than 10 times of N-infusion trials using 1.3 GHz single-cell cavities. Some results showed better Q-values up to high field, however, some results showed degraded Q-E slopes probably due to contamination. Improvement of accelerating gradient is not observed at moment. We have tried to clean the furnace and Nitrogen injection line to reduce the effect of contamination. Details of procedures of N-infusion, results of vertical tests, condition of the furnace including RGA spectrum and Nb sample analysis results are shown.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP027
About •	paper received ※ 04 July 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP028	Materials Science Investigations of Nitrogen-Doped Niobium for SRF Cavities	niobium, SRF, superconducting-RF, collider	99
	M. Major, L. Alff, M. Arnold, J. Conrad, S. Flege, R. Grewe, N. Pietralla TU Darmstadt, Darmstadt, Germany
	Funding: Work supported by the German Federal Ministry for Education and Research (BMBF) through grant 05H18RDRB2. Niobium is the standard material for superconducting RF (SRF) cavities for particle acceleration. Superconducting materials with higher critical temperature or higher critical magnetic field allow cavities to work at higher operating temperatures or higher accelerating fields, respectively. Enhancing the surface properties of the superconducting material in the range of the penetration depth is also beneficial. One direction of search for new materials with better properties is the modification of bulk niobium by nitrogen doping. In the Nb-N phase diagram, the cubic delta-phase of NbN has the highest critical temperature. Niobium samples were annealed and N-doped in the high-temperature furnace at TU Darmstadt and investigated at its Materials Research Department with respect to structural modifications. Secondary ion mass spectrometry showed at which conditions N-diffusion takes place. X-ray diffraction (XRD) confirmed the appearance of NbN and Nb₂N phases for the optimized doping process. XRD pole figures also showed grain growth during sample annealing.
	Poster MOP028 [2.555 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP028
About •	paper received ※ 05 July 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP029	N-Doping Studies With Single-Cell Cavities for the SHINE Project	niobium, SRF, FEL, ECR	102
	J.F. Chen, H.T. Hou, Y.F. Liu, D. Wang, Y. Wang SARI-CAS, Pudong, Shanghai, People’s Republic of China Y.W. Huang ShanghaiTech University, Shanghai, People’s Republic of China Z. Wang SINAP, Shanghai, People’s Republic of China
	The SHINE SRF accelerator is designed to operate in CW mode with more than six hundred superconducting cavities. In order to reduce the high cost of construction and operation of the cryogenic system, high-Q cavities with nitrogen-doping technology together with tradition-ally treated large-grain cavities have been considered as two possible options. In this paper, we present N-doping studies on single-cell cavities fabricated with fine-grain and large-grain niobium.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP029
About •	paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP030	Analysis of Surface Nitrides Created During "Doping" Heat Treatments of Niobium	niobium, SRF, lattice, controls	106
	J.K. Spradlin, A.D. Palczewski, C.E. Reece, H. Tian JLab, Newport News, Virginia, USA
	Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. The benefits of reduced RF losses from interstitial "doping" of niobium are well established. Many of the details involved in the process remain yet to be elucidated. The niobium surface reacted with low-pressure nitrogen at 800°C presents a surface with chemical reactivity different than standard niobium. While standard "recipes" are being used to produce cavities, we seek additional insight into the chemical processes that may be used to remove the "undesirable" as-formed surface layer. This may lead to new processing routes or quality assurance methods to build confidence that all surface "nitrides" have been removed. We report a series of alternate chemistry treatments and subsequent morphological examinations and interpret the results. We also introduce a new standardized Nb sample system in use for efficient characterization of varying doping protocols and cross-laboratory calibration.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP030
About •	paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP031	Investigation of Frequency Behavior Near Tc of Niobium Superconducting Radio-Frequency Cavities	SRF, niobium, electron, ECR	112
	D. Bafia, J. Zasadzinski IIT, Chicago, Illinois, USA D. Bafia, M. Checchin, A. Grassellino, O.S. Melnychuk, A.S. Romanenko, D.A. Sergatskov Fermilab, Batavia, Illinois, USA
	This paper will present a systematic investigation of the resonant frequency behavior of niobium SRF cavities subject to different surface processing (nitrogen doping, nitrogen infusion, 120°C bake, EP, etc.) near the critical transition temperature. We find features occurring in frequency versus temperature (FvsT) data near Tc that seem to vary with surface processing. Emphasis is placed on one of the observed features: a dip in the superconducting resonant frequency below the normal conducting value which is prominent in nitrogen doped cavities and appears to be a signature of nitrogen doping. This gives further insights on the mechanisms responsible for the large increase in performance of cavities subject to this surface treatment. The magnitude of this dip in frequency is studied and related to possible physical parameters such as the concentration of impurities near the surface and the design resonant frequency of the cavity. A possible explanation for the meaning of this dip is discussed, namely, that it is a result of strong coupling between electrons and phonons within the resonator.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP031
About •	paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP032	Effect of Low Temperature Infusion Heat Treatments and "2/0" Doping on Superconducting Cavity Performance	ECR, niobium, SRF, background	118
	P.N. Koufalis, M. Ge, M. Liepe, J.T. Maniscalco Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
	Under specific circumstances, low temperature infusion heat treatments of niobium cavities have resulted in the ubiquitous "Q-rise". This is an increase in quality factor with increasing field strength or equivalently a decrease in the temperature-dependent component of the surface resistance. We investigate the results of various infusion conditions with infusion bake time as a free parameter. To study the very near surface effects of infusion, we employ HF rinsing, light VEP, and oxypolishing to remove several or tens of nm at a time. We present results from RF performance tests of low temperature infusion heat treated niobium cavities, and correlate these with SIMS impurity depth profiles obtained from witness samples. We also present results of a cavity doped at 800 C with the "2/0" recipe.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP032
About •	paper received ※ 26 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP033	The Beam Dynamics Updates of the Fermilab PIP-II 800 MeV Superconducting Linac	linac, SRF, optics, emittance	123
	A. Saini, V.P. Yakovlev Fermilab, Batavia, Illinois, USA E. Pozdeyev FRIB, East Lansing, Michigan, USA
	The Proton Improvement Plan (PIP) -II is a high intensity proton facility being developed to support a neutrino program over the next two decades at Fermilab. At its core is the design and construction of a Continuous Wave compatible superconducting radio frequency linear accelerator that would accelerate an average beam current of 2 mA up to 800 MeV. This paper presents recent updates in the beam dynamics leading to a reliable and robust linac design and simplifying the cryo-module assembly.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP033
About •	paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP034	European XFEL: Accelerating Module Repair at DESY	FEL, linac, SRF, operation	127
	D. Kostin, J. Eschke, K. Jensch, N. Krupka, D. Reschke, S. Saegebarth, J. Schaffran, M. Schalwat, P. Schilling, M. Schmökel, S. Sievers, N. Steinhau-Kühl, E. Vogel, H. Weise, M. Wiencek, B. van der Horst DESY, Hamburg, Germany
	The European XFEL is in operation since 2017. The design projected energy of 17.5 GeV was reached, even with the last 4 main linac accelerating modules not yet installed. 2 out of 4 not installed modules did suffer from strong cavity performance degradation, namely increased field emission, and required surface processing. The first of two modules is reassembled and tested. The module test results confirm a successful repair action. The module repair and test steps are described together with cavities performance evolution.
	Poster MOP034 [1.863 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP034
About •	paper received ※ 17 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP035	Cryogenic Infrastructure at BESSY II – Current Installations and Future Developments	cryogenics, storage-ring, gun, radiation	131
	S. Heling, W. Anders, J. Heinrich, A. Hellwig, K. Janke, S. Rotterdam HZB, Berlin, Germany
	In Berlin-Adlershof the Helmholtz-Zentrum Berlin (HZB) is operating the synchrotron radiation source BESSY II. Two superconducting wave-length shifter magnets are built-in the storage ring of BESSY II which are cooled with liquid helium. Additionally several test facilities for superconducting cavities are operated at HZB needing helium at 1.8 K. The required helium is supplied by two helium liquefiers. Parallel to operation of the existing facilities the BERLinPro project will qualify as test facility for ERL science and technology. In order to guarantee the required supply with helium at different temperature levels one of the existing helium liquefiers has been relocated to the new accelerator building and the existing cryogenic infrastructure has been upgraded with a new 10 000 L dewar, three valve boxes, a cold compressor box, warm pumps and a 80 K helium system. This paper specifies the setup of the above described helium cryoplants in detail and gives insight into the challenges of development. The paper concludes with an outlook of the upcoming developments of the cryogenic infrastructure at HZB.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP035
About •	paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP036	Microphonics Suppression Study in ARIEL e-Linac Cryomodules	cryomodule, GUI, linac, pick-up	136
	Y. Ma, K. Fong, J.J. Keir, D. Kishi, S.R. Koscielniak, D. Lang, R.E. Laxdal, S.L. Liu, R.S. Sekhon, X. Wang TRIUMF, Vancouver, Canada
	Now the stage of the 30 MeV portion of ARIEL (The Advanced Rare Isotope Laboratory) e-Linac (1.3 GHz, SRF) is under commissioning which includes an injector cryomodule (ICM) with a single nine-cell cavity and the 1st accelerator cryomodule (ACM1) with two cavities configuration. The two ACM1 cavities are driven by a single klystron with vector-sum control and running in CW mode. We have observed a ponderomotive instability in ACM1 driven by the Lorentz force and seeded through microphonics that impacts beam stability [1-5]. Extensive damping has been implemented during a recent shut-down. The beam test results show 20 MeV acceleration gain can be reached by ACM1. A fast piezoelectric (Pie-zo) tuner is under development to allow a fast tuning compensation for the e-Linac cavities. In this paper, the progress of the microphonics suppression of Cryomod-ules is presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP036
About •	paper received ※ 24 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP039	Nitrogen Doping Studies of Superconducting Cavities at Peking University	niobium, accelerating-gradient, superconducting-cavity, ECR	141
	S. Chen, M. Chen, L.W. Feng, J.K. Hao, L. Lin, K.X. Liu, S.W. Quan, F. Wang, F. Zhu PKU, Beijing, People’s Republic of China
	Nitrogen doping studies with 1.3 GHz superconducting cavities were carried out at Peking University in recent years. We have realized 4×10¹⁰ of high quality factor at 12 MV/m and 2.0 K with large grain single cell cavities by heavy doping. To improve the accelerating gradient of high Q cavities, light doping recipe is adopted. Accelerating gradient is improved to 20 MV/m and the quality factor is larger than 3×10¹⁰ at 16 MV/m and 2.0 K for light doped cavities. The nitrogen treatment, test and analysis are presented in this paper.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP039
About •	paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP040	Low Temperature Thermal Conductivity of Niobium and Materials for SRF Cavities	niobium, SRF, experiment, controls	144
	M. Fouaidy Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France
	A test facility, allowing the test of 4 samples simultaneously during each run, was developed for measuring at low temperature (T= 1.5 K - 10 K) the thermal conductivity k(T) of niobium and other materials used for the fabrication of SRF cavities. The measurements are performed using steady-state axial heat flow method with a careful control of heat leaks to the surrounding. Several samples of different materials (industrial Nb sheets, Ti¿) were either tested as received or/and subjected to various Heat Treatment (H.T) prior to the experiment then tested. The resulting experimental data are presented and compared to the experimental results previously reported by other groups. As expected, H.T @ 1200°C with Ti gettering improves the Nb RRR by a factor of 3 and consequently k(T). Finally, the correlation between the Niobium RRR and the thermal conductivity. at T=4.2 K is confirmed in good agreement with the Wiedemann-Franz law.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP040
About •	paper received ※ 04 July 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP045	The LCLS-II HE High Q and Gradient R&D Program	SRF, cryomodule, linac, niobium	154
	D. Gonnella, S. Aderhold, A. Burrill, G.R. Hays, T.O. Raubenheimer, M.C. Ross SLAC, Menlo Park, California, USA D. Bafia, M. Checchin, A. Grassellino, M. Martinello, A.S. Romanenko Fermilab, Batavia, Illinois, USA M. Ge, M. Liepe, S. Posen Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA A.D. Palczewski, C.E. Reece JLab, Newport News, Virginia, USA
	Funding: US DOE and the LCLS-II HE Project The LCLS-II HE project is a high energy upgrade to the superconducting LCLS-II linac. It consists of adding twenty additional 1.3 GHz cryomodules to the linac, with cavities operating at a gradient of 20.8 MV/m with a Q₀ of 2.7·10¹⁰. Performance of LCLS-II cryomodules has suggested that operations at this high of a gradient will not be achievable with the existing cavity recipe employed. Therefore a research program was developed between SLAC, Fermilab, Thomas Jefferson National Accelerator Facility, and Cornell University in order to improve the cavity processing method of the SRF cavities and reach the HE goals. This program explores the doping regime beyond what was done for LCLS-II and also has looked to further developed nitrogen-infusion. Here we will summarize the results from this R\&D program, showing significant improvement on both single-cell and 9-cell cavities compared with the original LCLS-II cavity recipe.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP045
About •	paper received ※ 25 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP047	Progress of IFMIF/EVEDA Project and Prospects for A-FNS	neutron, rfq, radiation, SRF	159
	S. Ishida, A. Kasugai, K. Sakamoto QST, Aomori, Japan P. Cara IFMIF/EVEDA, Rokkasho, Japan H. Dzitko F4E, Germany
	International Fusion Materials Irradiation Facility (IFMIF) is an accelerator-based D-Li neutron source, in which two 40 MeV Deuteron(D) beams with a total current 250 mA impact on a liquid Li stream flowing at 15 m/s. In the IFMIF/EVEDA project under the Broader Approach (BA) agreement, the Li target was continuously operated with the cold trap and satisfied the stability requirement throughout the continuous operation. The Linear IFMIF Prototype Accelerator (LIPAc) is currently under development in Rokkasho, Japan, to demonstrate the 9 MeV/125 mA D⁺ beam acceleration. Recently, the first proton beam was injected into the RFQ with more than 90 % of transmission, followed by the first D⁺ beam accelerated at 5 MeV. The SRF linac necessary for the 9-MeV D⁺ beam is nearing completion of the manufacturing phase and will be assembled in Rokkasho. Based on these results, a conceptual design of the Advanced Fusion Neutron Source (A-FNS) for its construction in Rokkasho is underway to obtain material irradiation data for a DEMO reactor. The A-FNS is designed to be composed of an accelerator facility with a 40 MeV/125 mA D⁺ beam, a test facility including a liquid Li target system and a post irradiation examination facility, and to enable multipurpose utilization for neutron application.
	Poster MOP047 [2.327 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP047
About •	paper received ※ 29 June 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP049	Prototypes Fabrication of 1.3 GHz Superconducting Rf Components for SHINE	FEL, niobium, HOM, SRF	164
	H.T. Hou, J.F. Chen, Z.Y. Ma, J. Shi, Y. Wang SARI-CAS, Pudong, Shanghai, People’s Republic of China F.S. He IHEP, Beijing, People’s Republic of China S.W. Quan PKU, Beijing, People’s Republic of China
	Aiming to high repetition rate hard X-ray facility, con-struction of Shanghai HIgh repetition rate XFEL aNd Extreme light facility (SHINE) project has been ap-proved. During the R & D phase, prototypes fabrication of key components of 1.3GHz superconducting rf system have been proposed, especially 1.3 GHz 9-cell niobium cavities. Here the paper will present the progress of the fabrication status and performance of the prototypes, together with the analysis of not only the quality factor and gradient of the cavities. Consideration of HOM feed-throughs and absorbers are also reported.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP049
About •	paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP050	Modular Power Couplers for 217 MHz Superconducting CH-Cavities	Windows, linac, heavy-ion, simulation	168
	J. List, K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, T. Kürzeder, S. Lauber, M. Miski-Oglu HIM, Mainz, Germany K. Aulenbacher, W.A. Barth, C. Burandt, V. Gettmann, M. Heilmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu, A. Schnase, S. Yaramyshev GSI, Darmstadt, Germany K. Aulenbacher, F.D. Dziuba, S. Lauber, J. List IKP, Mainz, Germany M. Basten, M. Busch, H. Podlech, M. Schwarz IAP, Frankfurt am Main, Germany
	The HELmholtz LInear ACcelerator (HELIAC) is being developed by a collaboration of HIM, GSI and the Goethe University of Frankfurt. It is a superconducting (sc), continuous wave (cw) heavy ion linac that comprises novel Crossbar H-mode (CH) cavities. In April 2017 and November/December 2018 the first sc CH-cavity of the linac was tested with beam. The first operations of the cavity showed, that the prototype of the rf power coupler needs to be further improved. A new version of the coupler is being designed at the HIM. Further development will mainly be focused on the heat input into the cryostat caused by the coupler. Also the coupler will have a modular design. This improves the accessibility and maintenance of the coupler. Various cryogenic and rf tests are foreseen, to provide a reliable, fail-safe coupler for the HELIAC. For an enhanced coupler test stand a movable reflector has been designed and built. With its movable semi-reflective element, it allows to operate the test stand in a resonance mode. In addition, the movable reflector can vary the coupling factor. This contribution discusses the recent coupler R&D for the HELIAC.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP050
About •	paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP051	3.9 GHz SRF Production Cavities for LCLS-II	cryomodule, linac, radiation, vacuum	173
	S. Aderhold, A. Burrill SLAC, Menlo Park, California, USA D.J. Bice, C.M. Ginsburg, C.J. Grimm, T.N. Khabiboulline, O.S. Melnychuk, D.A. Sergatskov, N. Solyak, G. Wu Fermilab, Batavia, Illinois, USA
	Funding: This work was supported by the US DOE and the LCLS-II Project. The main part of the SRF linac for the Linac Coherent Light Source II (LCLS-II) at SLAC will consist of 35 cryomodules with superconducting RF cavities operating at 1.3 GHz. In addition, two cryomodules with 3.9 GHz cavities will be installed and help to linearize the longitudinal phase space of the beam. During the design verification phase, four prototype 9-cell 3.9 GHz cavities had been built by industry and then processed, including chemical surface removal and heat treatment, and tested at Fermi National Accelerator Laboratory. Based on the resulting cavity treatment recipe, 24 cavities (for two cryomodules to be installed in the linac and one spare cryomodule) have been built by industry and tested at Fermilab prior to cryomodule string assembly. We present an overview of the cavity production and the results of the vertical acceptance tests for the LCLS-II 3.9 GHz cavities.
	Poster MOP051 [1.015 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP051
About •	paper received ※ 02 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP054	Fabrication of 3.0-GHz Single-cell Cavities for Thin-film Study	SRF, MMI, FEL, linac	177
	T. Saeki, H. Hayano, H. Inoue, R. Katayama, T. Kubo KEK, Ibaraki, Japan F.E. Hannon, R.A. Rimmer, A-M. Valente-Feliciano JLab, Newport News, Virginia, USA H. Ito Sokendai, Ibaraki, Japan Y. Iwashita, H. Tongu Kyoto ICR, Uji, Kyoto, Japan
	Funding: This work is supported by JSPS KAKENHI JP17H04839, JSPS KAKENHI JP26600142, Japan-US Research Collaboration Program, and the Collaborative Research Program of ICR Kyoto Univ. (2018-13). We fabricated 3.0-GHz single-cell cavities with Cu and Nb materials for testing thin-film creations on the inner surface of the cavities in collaboration between Jefferson Laboratory (JLab) and KEK. The cavity was designed at JLab. According to the design of cavity, the press-forming dies and trimming fixtures for the cavity-cell were also designed and fabricated at JLab. These dies and trimming fixtures were transported to KEK, and the rest of fabrication processes were done at KEK. Finally nine Cu 3.0-GHz single-cell cavities and six Nb 3.0-GHz single-cell cavities were fabricated. Two Cu 3.0-GHz single-cell cavities were mechanically polished at Jlab. All of these cavities will be utilized for the tests of various thin-film creations at JLab and KEK. This presentation describes details of the fabrication of these cavities.
	Poster MOP054 [1.203 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP054
About •	paper received ※ 05 July 2019 paper accepted ※ 13 August 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP055	Fabrication and Performance of Superconducting Quarter-Wavelength Resonators for SRILAC	linac, operation, cryomodule, acceleration	182
	K. Suda, O. Kamigaito, K. Ozeki, N. Sakamoto, Y. Watanabe, K. Yamada RIKEN Nishina Center, Wako, Japan H. Hara, A. Miyamoto, K. Sennyu, T. Yanagisawa MHI-MS, Kobe, Japan E. Kako, H. Nakai, H. Sakai, K. Umemori KEK, Ibaraki, Japan
	A new superconducting booster linac (SRILAC) at the RIKEN heavy-ion linac is under construction. Ten 73-MHz low-beta quarter-wavelength resonators (QWRs) that operate at 4 K have been fabricated from pure niobium sheets. The cavity parts were assembled by electron beam welding. The resonant frequency for each cavity was adjusted by changing the lengths of the straight sections before welding. The performance and frequency were evaluated by vertical tests. All the cavities exceeded the design specifications of Q₀ = 1x10⁹ and E_acc = 6.8 MV/m. Details of the fabrication and frequency tuning as well as the performance of the cavities are reported.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP055
About •	paper received ※ 17 July 2019 paper accepted ※ 13 August 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP056	Surface Treatments for the Series Production of ESS Medium Beta Cavities	recirculation, SRF, niobium, simulation	188
	M. Bertucci, A. Bosotti, A. D’Ambros, P. Michelato, L. Monaco, C. Pagani, R. Paparella, D. Sertore INFN/LASA, Segrate (MI), Italy C. Pagani Università degli Studi di Milano & INFN, Segrate, Italy D. Rizzetto, M. Rizzi Ettore Zanon S.p.A., Schio, Italy A. Visentin Ettore Zanon S.p.A., Nuclear Division, Schio, Italy
	The surface treatment of ESS 704 MHz medium beta cavities consists of a bulk BCP 200 micron removal, a 10 h 600°C heat treatment and a final 20 micron BCP performed after tank integration. The facility currently employed for the BCP treatment, settled in Ettore Zanon SpA, is here presented, together with the results so far obtained on the first series cavities in terms of frequency sensitivity, removal rate and surface external temperature. The optimization of BCP treatment by a preliminary fluid-dynamical finite element model is also discussed. Some details about the visual inspection procedure and the furnace qualification are also presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP056
About •	paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP057	Electropolishing of PIP-II Low Beta Cavity Prototypes	cathode, experiment, FEL, linac	194
	M. Bertucci, A. Bosotti, A. D’Ambros, P. Michelato, L. Monaco, C. Pagani, R. Paparella, D. Sertore INFN/LASA, Segrate (MI), Italy A. Gresele, A. Visentin Ettore Zanon S.p.A., Nuclear Division, Schio, Italy C. Pagani Università degli Studi di Milano & INFN, Segrate, Italy D. Rizzetto, M. Rizzi Ettore Zanon S.p.A., Schio, Italy
	We present the upgrade of the EP facility for the surface treatment of PIP-II low beta cavities. The main process parameters, such as voltage, treatment time, acid throughput and cathode geometry, already optimized on the previous experience of 1.3 GHz Tesla-shape cavities, are discussed taking into account the different cavity size and geometry. The first surface treatments have been performed at Ettore Zanon SpA on single cell cavity prototypes in order to reach good final surface finishing and the required thickness removal. In the meantime, the upgrade of the system for the treatment of multicell PIP-II prototype cavities is presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP057
About •	paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP058	ESS Medium Beta Activity at INFN LASA	HOM, status, controls, SRF	199
	D. Sertore, M. Bertucci, A. Bignami, A. Bosotti, M. Chiodini, A. D’Ambros, G. Fornasier, P. Michelato, L. Monaco, R. Paparella INFN/LASA, Segrate (MI), Italy S. Aurnia, O. Leonardi, A. Miraglia, G. Vecchio INFN/LNS, Catania, Italy A. Gresele, A. Visentin Ettore Zanon S.p.A., Nuclear Division, Schio, Italy C. Pagani Università degli Studi di Milano & INFN, Segrate, Italy D. Reschke, A. Sulimov, M. Wiencek DESY, Hamburg, Germany D. Rizzetto, M. Rizzi Ettore Zanon S.p.A., Schio, Italy L. Sagliano ESS, Lund, Sweden
	The industrial production of the 36 resonators (plus 2 spares) for the ESS linac started and it is steadily progressing. Cavities are delivered by industry as fully surface-treated and dressed to AMTF facility at DESY for their qualification via vertical cold-test. This paper reports the current status of the manufacturing process from sub-components to processing of the complete cavity inner surface. It also reviews the documental control strategy deployed to preserve the fulfillment of ESS requirements as well as the cavity performances demonstrated so far.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP058
About •	paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP060	INFN-LASA for the PIP-II Project	niobium, SRF, interface, linac	205
	R. Paparella, M. Bertucci, A. Bignami, A. Bosotti, M. Chiodini, A. D’Ambros, P. Michelato, L. Monaco, D. Sertore INFN/LASA, Segrate (MI), Italy J.F. Chen SARI-CAS, Pudong, Shanghai, People’s Republic of China C. Pagani Università degli Studi di Milano & INFN, Segrate, Italy L. Sagliano ESS, Lund, Sweden
	INFN-LASA joined the international effort for the PIP-II project in Fermilab to build the 650 MHz superconducting cavities realizing the low-beta section of the 800 MeV proton linac. After developing the electro-magnetic and mechanical design, INFN-Milano started the prototyping phase by producing five single-cells and two complete 5-cells cavities. This paper reports the status of PIP-II activities at INFN-LASA summarizing manufacturing experience and preliminary experimental results.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP060
About •	paper received ※ 24 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP061	State of the Art of Niobium Machining for SRF Applications	niobium, SRF, electron, alignment	210
	P. Naisson, S. Atieh, K. Scibor, P. Trubacova CERN, Geneva, Switzerland F. Dumont, D. Fabre, F. Valiorgue ENISE, Saint Etienne, France
	Niobium is a demanding material to be machined. Its low hardness, high melting temperature and abrasivity leads to poor cutting condition, and surface quality and shape accuracy could be difficult to achieve, especially for complex shapes such as HOM antennas. Recent CERN developements concerning DQW crab cavity for HL-LHC project had implied extensive research program to better understand and master the machining of this material. In this frame, the present article will introduce actual state of the art machining condition used at CERN and their consequences about the surface roughness, shape accuracy and taking into account the tool wear in order to maintain this level of quality. Morevoer, advance machning solution, such as cryogenic cooling could be used.
	Poster MOP061 [2.921 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP061
About •	paper received ※ 30 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP062	Fabrication of SRF Cavity	coupling, vacuum, SRF, pick-up	214
	K. Kanaoka, H. Hara, A. Miyamoto, K. Sennyu, T. Yanagisawa MHI-MS, Kobe, Japan E. Kako, K. Umemori KEK, Ibaraki, Japan
	Mitsubishi Heavy Industries Machinery Systems (MHI-MS) have developed manufacturing process of superconducting cavities for a long time. In this presentation, recent progress will be reported.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP062
About •	paper received ※ 23 June 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP063	Beam Loading in the BESSY VSR SRF Cavities	beam-loading, SRF, storage-ring, operation	217
	A.V. Tsakanian, H.-W. Glock, J. Knobloch, A.V. Vélez HZB, Berlin, Germany
	The BESSY VSR upgrade of the BESSY II light source represents a novel approach to simultaneously store long (ca. 15 ps) and short (ca. 1.7 ps) bunches in the storage ring at currents up to 300 mA. This challenging goal requires installation of four new 4-cell SRF cavities (2x1.5 GHz and 2x1.75 GHz) in one module for installation in a single straight. As far as we are aware of, this is the first installation of multi-cell L-Band cavities in a high-current storage ring. These cavities are equipped with newly developed waveguide HOM dampers necessary for stable operation. Up to 2 kW of HOM power must be absorbed. Operating two SRF cavities for each frequency will also enable transparent parking of the cavities for the beam. Based on wakefield theory, a technique for beam loading calculation will be presented. The expected beam loading both at 2 K and at room temperature has been analyzed to evaluate transparent parking for both situations. The presented study is performed for various BESSY II and VSR bunch filling patterns with 300 mA beam current.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP063
About •	paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP064	Performance of First Prototype Multi-Cell Low-Surface-Field Shape Cavity	SRF, electron, niobium, experiment	222
	R.L. Geng JLab, Newport News, Virginia, USA Y. Fuwa, Y. Iwashita Kyoto ICR, Uji, Kyoto, Japan H. Hayano KEK, Ibaraki, Japan H. Ito Sokendai, Ibaraki, Japan Z. Li SLAC, Menlo Park, California, USA
	The idea of cavity shaping for higher ultimate acceleration gradients has been proposed for some time, Low Loss/Ichiro and Re-entrant being examples, both seeking a lower Hpk/E_acc at the expense of a higher Epk/E_acc. While experimental verification in single-cell cavities of those shapes was very successful including the record gradient of 59 MV/m, pushing multi-cell cavities of those shapes to higher gradients was prevented by field emission. The Low-Surface-Field (LSF) shape seeks not only a lower Hpk/E_acc but also a lower Epk/E_acc, therefore it has the advantage of raising ultimate gradient at reduced field emission. The first multi-cell LSF shape prototype cavity was built using the standard forming and welding techniques. RF tests have been carried out, following standard ILC TDR baseline surface processing and treatment recipe. Three out of five cells achieved Hpk values corresponding to E_acc 50 MV/m. The current limit is the field emission in end cells. Instrumented testing following end-cell wiping and HPR with larger nozzles is in progress. We will present detailed experimental results and preparation procedures.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP064
About •	paper received ※ 24 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP065	Upgrade of the S-DALINAC Injector Capture Section	linac, MMI, gun, target	227
	S. Weih, M. Arnold, J. Enders, N. Pietralla TU Darmstadt, Darmstadt, Germany D.B. Bazyl, H. De Gersem, W.F.O. Müller TEMF, TU Darmstadt, Darmstadt, Germany
	Funding: Work supported by DFG through GRK 2128 "AccelencE" The superconducting injector section of the S-DALINAC (superconducting Darmstadt linear electron accelerator) [1] constists of two cryomodules with three 3-GHz SRF cavities in total. The first cavity of this pre-accelerator is currently a 5-cell structure designed for relativistic particle velocities. Since the gun delivers a 250 keV beam (β=0.74), this cavity is not suited for an efficient capture of the low-energy electron bunches provided by the normal-conducting section of the injector. Beam dynamics simulations and operational experience have shown a large low-energy tail in the phase-space distribution of the bunch downstream of the injector, which arises from the large phase-slippage during the capture in the 5-cell. It is therefore intended to replace the cavity with a beta-adapted 6-cell, re-using most of the cryostat parts. This contribution presents the status of the injector upgrade and the layout and manufacturing status of the new cavity. *N. Pietralla, Nuclear Physics News, Vol. 28, No. 2, 4 (2018)
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP065
About •	paper received ※ 21 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP070	Investigation of the Critical RF Fields of Superconducting Cavity Connections	simulation, vacuum, niobium, impedance	230
	J.C. Wolff, J.I. Iversen, D. Klinke, D. Kostin, D. Reschke, S. Sievers, A. Sulimov, J.H. Thie, M. Wiencek DESY, Hamburg, Germany R. Wendel, J.C. Wolff HAW Hamburg, Hamburg, Germany
	To optimise the length of the drift tube of a superconducting cavity (SC), it is required to know the critical value of the RF fields to prevent a potential early quench at the flange connection in case of a drift tube length reduction. To avoid changes on the SC which has been used for the tests, all RF cryogenic experiments have been carried out by using a cylinder in the center of a 1-cell cavity drift tube to increase the field magnitude at the connection. This cylinder has been designed and optimised by RF simulations to provide a field density at the connection twice as high as at a chosen reference point near the iris. Hence also a test SC with a comparatively low gradient can be used without causing field restrictions. In this contribution an approach to investigate the field limitations of 1.3 GHz TESLA-Shape SC connections and thereby the minimal drift tube length based on simulations will be presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP070
About •	paper received ※ 23 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP072	FRIB Solenoid Package in Cryomodule and Local Magnetic Shield	solenoid, cryomodule, operation, dipole	235
	K. Saito, H. Ao, B. Bird, R. Bliton, N.K. Bultman, F. Casagrande, C. Compton, J. Curtin, K. Elliott, A. Ganshyn, W. Hartung, L. Hodges, K. Holland, S.H. Kim, S.M. Lidia, D. Luo, S.J. Miller, D.G. Morris, L. Nguyen, D. Norton, J.T. Popielarski, L. Popielarski, T. Russo, J.F. Schwartz, S.M. Shanab, M. Shuptar, D.R. Victory, C. Wei, J. Wei, M. Xu, T. Xu, Y. Yamazaki, C. Zhang, Q. Zhao FRIB, East Lansing, Michigan, USA A. Facco INFN/LNL, Legnaro (PD), Italy K. Hosoyama, M. Masuzawa KEK, Ibaraki, Japan R.E. Laxdal TRIUMF, Vancouver, Canada
	Funding: U.S. Department of Energy Office of Science under Cooperative Agreement DE -SC0000661 FRIB cryomodule design has a feature: solenoid package(s) and local magnetic shields in the cryomodule. In this design, exposing SRF cavities to a very strong fringe field from the solenoid is concerned. A tangled issue between solenoid package design and magnetic shield one has to be resolved. FRIB made intensive studies, designed, prototyped, validated the solenoid packages and magnetic shields, and finally certified them in the bunker test. This paper reports activity results, and LS1 commissioning results in FRIB tunnel. This is a FRIB success story.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP072
About •	paper received ※ 24 June 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP074	External Q Measurement for Quarter Wave Resonators in RISP	pick-up, cryomodule, simulation, coupling	245
	S. Lee, B.H. Choi, M.O. Hyun, Y. Jung, J.W. Kim, Y. Kim, J. Lee, K.T. Seol IBS, Daejeon, Republic of Korea
	A heavy-ion accelerator facility is under construction for Rare Isotope Science Project(RISP) in Korea. The super conducting cavity, quarter wave resonator(QWR) which consists of driver and post linear accelerator system, is now in the mass production phase. In order to develop the QWR cavity and cryomodule, the RF couplers are fabriacated and tested. In this paper, the study of external Q for QWR coupler will be described.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP074
About •	paper received ※ 21 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP075	Design of RF Power Coupler Transmitting both 162.5 MHz and 81.25 MHz Power to SRF Cavities for BISOL R&D Research	ISOL, simulation, RF-structure, Windows	249
	F. Zhu, M. Chen, A.Q. Cheng, J.K. Hao, S.W. Quan, F. Wang PKU, Beijing, People’s Republic of China
	Beijing isotope separation on line type rare ion beam facility (BISOL) is a proposed facility which has two superconducting RF linacs. One is a high intense driver linac which adopts half wave resonators (HWRs), and the other is the low current post-accelerator which includes quarter wave resonators (QWRs). For the pre-research of BISOL, a cryomodul which can do the horizontal test of both 81.25 MHz QWR for the post-accelerator and 162.5 MHz HWR for the driver accelerator with the proper external quality factor. For this purpose, Peking University are developing a coupler which can transfer 5 kW power to the 81.25 MHz QWR or cw 20 kW power to the 162.5 MHz HWR cavity. The electromagnetic optimization, Multipacting simulation, thermal analysis and detail structure of the coupler will be presented in this paper.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP075
About •	paper received ※ 21 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP076	Fundamental Power Coupler Design for a 325 MHz Balloon SSR Cavity	multipactoring, vacuum, simulation, cryogenics	252
	R.E. Laxdal, Y. Ma, B. Matheson, B.S. Waraich, Z.Y. Yao, V. Zvyagintsev TRIUMF, Vancouver, Canada
	TRIUMF has designed, fabricated and tested the first balloon variant of the single spoke resonator at 325 MHz and β=0.3. TRIUMF has also designed a 6 kW fundamental power coupler as part of the development. The design of the coupler will be presented.
	Poster MOP076 [1.282 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP076
About •	paper received ※ 24 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP078	Adjustable Power Coupler for NICA HWR Cavities	vacuum, simulation, coupling, collider	260
	S.V. Matsievskiy, M.V. Lalayan MEPhI, Moscow, Russia D. Bychanok INP BSU, Minsk, Belarus M. Gusarova JINR, Dubna, Moscow Region, Russia
	Current results on input power coupler development for Half-Wave superconducting accelerating cavity proposed for Nuclotron-based Ion Collider fAcility (NICA) collider injector upgrade are discussed. Two coupler designs are considered, first one is a low-power coupler for cavity tests and the second one is a high-power operational coupler. Both devices are of coaxial type with capacitive coupling; high-power coupler utilizes single ceramic vacuum window. NICA is designed to accelerate different types of ions. Due to the variable intensity of ion sources, beam current will vary in wide range. In order to ensure efficient acceleration, power coupler must be highly adjustable in terms of coupling coefficient. This introduces excessive mechanical stress in the ceramic RF window due to the bellows deformation. In order to mitigate this effect bellows were substituted with sliding contacts. This paper discusses new coupler design and its electrical, mechanical and thermal properties.
	Poster MOP078 [1.296 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP078
About •	paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP080	Latest Progress in Designs and Testings of PIP-II Power Couplers	rfq, vacuum, multipactoring, cryogenics	263
	S. Kazakov, B.M. Hanna, O.V. Pronitchev, N. Solyak Fermilab, Batavia, Illinois, USA
	Proton Improvement Plan – II (PIP-II) project is under go in Fermi National Laboratory. Main part of the project is 800 MeV proton superconducting accelerator which includes 116 superconducting cavities of 5 different types and three 162.5, 325 and 650 MHz frequencies. Key elements of accelerator which determine a reliable operation are main couplers for superconducting cavities. This paper describes the latest progress in design and testing of main couplers for PIP-II projects.
	Poster MOP080 [0.881 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP080
About •	paper received ※ 18 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP081	Considerations for Efficient RF Operation for the Advanced cw-Linac Demonstrator at GSI	linac, cryomodule, heavy-ion, SRF	267
	C. Burandt, K. Aulenbacher, W.A. Barth, F.D. Dziuba, V. Gettmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu, S. Yaramyshev HIM, Mainz, Germany K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, M. Heilmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu, A. Schnase, S. Yaramyshev GSI, Darmstadt, Germany K. Aulenbacher, F.D. Dziuba, S. Lauber, J. List IKP, Mainz, Germany M. Basten, M. Busch, H. Podlech, M. Schwarz IAP, Frankfurt am Main, Germany
	The FAIR@GSI accelerator facility will require the GSI-UNILAC to provide short heavy ion pulses of highest intensity at low repetition rate for injection into the 18 Tm synchrotron SIS18. However, successful physics programs like SHE (Super Heavy Elements) rely on the UNILAC providing for heavy ion beams of high average current and high duty factor. In the next future, a dedicated super-conducting (sc) cw-Linac should therefore deliver cw beams to the experiments associated with those programs. As a first step towards this goal, beam tests with a single sc Cross-bar H-mode (CH) cavity were successfully conducted in 2017/2018. Within the scope of an Advanced Demonstrator project, current activities now aim at a beam test of a full cryomodule with three sc CH cavities and a sc rebuncher. Given a limited amount of rf power available per cavity and the necessity to accelerate different ion species with different mass-to-charge ratios, the loaded quality factor Q of the different resonators has to be chosen very carefully. This contribution discusses the simulations performed in this context.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP081
About •	paper received ※ 21 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP084	A Simple Variable Coupler for the Cryogenic Test of SRF Cavities	SRF, cryogenics, coupling, FEL	282
	G. Ciovati, L. Turlington JLab, Newport News, Virginia, USA
	Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. The cryogenic rf tests of SRF cavities in vertical cryostats is typically carried out using fixed-length antennae to couple rf power into the cavity and to probe the energy stored into the cavity. Although variable couplers have been designed, built and used in the past, they are often a complex, costly, not very reliable auxiliary component to the cavity test. In this contribution we present the design and implementation of a simple variable rf antenna which has about 50 mm travel, allowing to obtain about four orders of magnitude variation in Q_ext -value. The motion of the antenna is driven by a motorized linear feedthrough outside of the cryostat. The antenna can easily be mounted on the most common type of cavity flanges.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP084
About •	paper received ※ 18 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP085	The Destructive Effects to the RF Coupler by the Plasma Discharge	plasma, experiment, vacuum, coupling	285
	A.D. Wu, Q.W. Chu, H. Guo, Y. He, S.C. Huang, T.C. Jiang, C.L. Li, Z.Q. Lin, F. Pan, Y.K. Song, T. Tan, W.M. Yue, S.H. Zhang, H.W. Zhao IMP/CAS, Lanzhou, People’s Republic of China
	The low temperature RF plasma was proved an effec-tive method to clean the niobium surface and relieve the field emission effect for the SRF cavities. In the case of half-wave resonators, these cavities were usually powered via the fundamental coupler with the electric coupling. Thus, coupler antennas were fixed in the intense electric field region, and this region was where the plasma rou-tinely ignited. Therefore, the ceramic window of coupler taken the risk of breakdown under the sputtering of ions and heating loads that may be caused by the plasma drift and diffusion from the electric field region. In this paper, the plasma ignition for surface cleaning on the HWR cavity and its coupler was investigated, and the power transmission, temperature raising and vacuum degradation were tested to characterize the adverse impacts on the ceramic window. Finally, the solution was proposed to figure these issues.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP085
About •	paper received ※ 22 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP086	Conditioning of the First Mass Production Power Couplers for the ESS Elliptical Cavities	vacuum, electron, pick-up, Windows	288
	C. Arcambal, M. Baudrier, P. Bosland, G. Devanz, T. Hamelin, C. Marchand, M. Oublaid, G. Perreu, S. Regnaud, C. Servouin, C. Simon CEA-DRF-IRFU, France G. Monnereau CEA-IRFU, Gif-sur-Yvette, France
	In the framework of the European Spallation Source (ESS), CEA Paris-Saclay is in charge of the delivery of 9 medium beta (β = 0.67) and 21 high beta (β = 0.86) cryomodules. Each cryomodule is composed of 4 cavities equipped with RF (Radio Frequency) power couplers (704.42 MHz, 1.1 MW maximum peak power, repetition rate=14 Hz, RF pulse width > 3.1 ms). Ten prototype power couplers have been manufactured to validate the design and the performance. Currently the mass production of the 120 couplers started and the six first pre-series medium beta couplers have been successfully conditioned. The achievement of this milestone allowed us to launch the production of the remaining 30 medium beta couplers. This paper presents the conditioning of the pre-series couplers.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP086
About •	paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP087	IFMIF Resonators Development and Performance	SRF, cryomodule, linac, solenoid	293
	G. Devanz, M. Baudrier, P. Carbonnier, F. Éozénou, E. Fayette, D. Roudier, P. Sahuquet, C. Servouin CEA-DRF-IRFU, France N. Bazin, S. Chel, L. Maurice CEA-IRFU, Gif-sur-Yvette, France
	The prototype IFMIF cryomodule encloses eight superconducting 175 MHz beta 0.09 Half-Wave Resonators (HWR). They are designed together with the power coupler to accelerate a high intensity deuteron beam (125 mA) from to 5 to 9 MeV. One prototype HWR and the 8 cavities to be hosted in the cryomodule have been manufactured, prepared and tested. The paper describes the phases of the cavities development, including fabrication, processing, and RF resonant frequency management. We focus on the results of the RF tests which have been performed for all bare and jacketed HWRs in a vertical cryostat.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP087
About •	paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP089	Development of a Suspension System for the Road Transportation of Cryomodule SSR1 through a Multilevel Finite Element-Multibody Approach	ISOL, cryomodule, software, simulation	297
	P. Neri, F. Bucchi University of Pisa, Pisa, Italy D. Passarelli Fermilab, Batavia, Illinois, USA
	The on-road transportation of cryomodules (CM) is a critical phase during which the structure may be subject to relevant dynamic loading. Thus, an accurate design of Transportation Tool (TT), equipped with a proper suspension system, is mandatory. In this paper the TT design for the PIP-II proto SSR1 CM is presented. A finite element (FE) model was developed considering the main CM parts. However, the full model was not suited for the design of the suspension system because of its computational time. Thus, it was exported as a Modal Neutral File to a multibody (MB) software, where minor components were modeled as rigid bodies or lumped stiffnesses. The reduced MB model considerably shortened the computational time and it was exploited for the design of the TT, which includes helical isolators (HI) acting as a mechanical filter. A real 3D acceleration profile, acquired during the transportation of a LCLS-II CM from Fermilab to SLAC, was used to validate the TT effectiveness in reducing the vibrational loading. In addition, the results of the MB analysis were used to perform FE analysis of critical components, such as bellows.
	Poster MOP089 [0.995 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP089
About •	paper received ※ 29 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP092	Overview of LCLS-II Project Status at Fermilab	cryomodule, SRF, cryogenics, controls	302
	R.P. Stanek, T.T. Arkan, J.N. Blowers, C.M. Ginsburg, A. Grassellino, C.J. Grimm, B.J. Hansen, E.R. Harms, B.D. Hartsell, J.P. Holzbauer, J.A. Kaluzny, A.L. Klebaner, A. Martinez, T.H. Nicol, Y.O. Orlov, K.S. Premo, N. Solyak, J. Theilacker, G. Wu Fermilab, Batavia, Illinois, USA
	The superconducting RF Continuous-Wave (CW) Linac for the LCLS-II consists of thirty-five 1.3 GHz and two 3.9 GHz cryomodules that Fermilab and Jefferson Lab are jointly producing in collaboration with SLAC. Fermilab¿s scope of work is to build, test, and deliver half the 1.3 GHz and all the 3.9 GHz cryomodules and to design and procure components for the cryogenic distribution system. Fermilab has primary responsibility for delivering a working design. The cryomodule design basis was the European XFEL but several elements evolved to meet CW operation requirements and specifics of the SLAC tunnel. There have been several challenges faced during the design, assembly, testing and transportation of the cryomodules which have required design updates. Success in overcoming these challenges is attributable to the strength of the LCLS-II SRF Collaboration (Fermilab, Jefferson Lab and SLAC with extensive help from DESY and CEA/Saclay). The cryogenic distribution system has progressed relatively well and there are valuable Lessons Learned. An overview of the status, accomplishments, problems encountered, solutions developed, and a summary of Lessons Learned will be presented.
	Poster MOP092 [0.393 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP092
About •	paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP094	Design Strategy of the PIP-II Cryomodules	cryomodule, vacuum, interface, cryogenics	307
	V. Roger, S.K. Chandrasekaran, D. Passarelli Fermilab, Batavia, Illinois, USA
	Funding: This manuscript has been authored by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the U.S. Department of Energy, Office of Science, Office of High Energy Physics The Proton Improvement Plan II (PIP-II) is the first U.S. accelerator project that will have significant contributions from international partners. Research institutions in India, Italy, UK and France will build major components of the particle accelerator. The High Beta 650 MHz (HB650) prototype cryomodule is being designed jointly between Fermilab (USA), CEA (France), STFC (UK) and RRCAT (India). The assembly of this prototype cryomodule will be done at Fermilab whereas the production cryomodules will be assembled in UK. Concerning the Low Beta 650 MHz (LB650) cryomodules, they will be designed and assembled at CEA. To reduce the cost of the project and to increase the quality it is essential to define a design strategy for each cryomodule which includes a degree of standardization. In this way, the lessons learned of each prototype cryomodule will have a great impact not only on one cryomodule type but on all cryomodules. An international joint design brings also additional challenges to the project: which unit system should be used? Should a common project lifecycle management system be used for all partners? How to transport the cryomodules overseas.
	Poster MOP094 [1.117 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP094
About •	paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP097	Preliminary Design of the IFMIF-DONES Superconducting Linac	cryomodule, linac, SRF, neutron	311
	T. Plomion, N. Bazin, N. Chauvin, G. Devanz, J. Plouin, K. Romieu CEA-DRF-IRFU, France S. Chel CEA-IRFU, Gif-sur-Yvette, France
	The linear accelerator for the DONES facility (DEMO oriented neutron source) will serve as a neutron source for the assessment of materials damage in future fusion reactors. The DONES accelerator, which is based on the design of LIPac (Linear IFMIF Prototype Accelerator, which is under construction in Rokkasho, Japan) will accelerate deuterons from 100 keV up to 40 MeV at full CW current of 125 mA. This paper will present the preliminary design of the superconducting linac which is based on five cryomodules.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP097
About •	paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP098	Spoke Cryomodule Prototyping for the MINERVA Project	cryomodule, cryogenics, operation, controls	315
	H. Saugnac, S. Blivet, N. Gandolfo, C. Joly, W. Kaabi, J. Lesrel, D. Longuevergne, G. Olivier, M. Pierens, W. Sarlin Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France M.A. Baylac, D. Bondoux, F. Bouly, P.-O. Dumont, Y. Gómez Martínez LPSC, Grenoble Cedex, France
	In the framework of the MINERVA (MYRRHA 100 MeV) project, a prototyping period started at the end of 2017, has been planned. During this period a prototype cryomodule fully equipped (Spoke Cavities, Cryomodule Vessel, Cold Tuning System, Magnetic shielding, Power Couplers¿) as well as its operating and controlling components (LLRF, RF amplifiers¿) will be studied and manufactured. The aim of this prototyping period is first to complete the study of all the components and to validate the manufacturing and the assembling procedure in order to freeze the specifications for the serial construction. On the other hand the prototypes will serve as a test stand allowing to study and adjust the "Fault Tolerance" strategy parameters , which is a challenging operating concept specific to the MYRRHA LINAC This poster presents the various tasks related to this Spoke Cryomodule prototyping and their status.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP098
About •	paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP099	Design of Crab Cavity Cryomodule for HL-LHC	cryomodule, vacuum, cryogenics, operation	320
	T. Capelli, K. Artoos, A.B. Boucherie, K. Brodzinski, R. Calaga, S.J. Calvo, E. Cano-Pleite, O. Capatina, F. Carra, L. Dassa, F. Eriksson, M. Garlasché, A. Krawczyk, R. Leuxe, P. Minginette, E. Montesinos, B. Prochal, M. Sosin, M. Therasse CERN, Geneva, Switzerland T.J. Jones, N. Templeton STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom A. Krawczyk, B. Prochal IFJ-PAN, Kraków, Poland S.M. Pattalwar STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
	Funding: Research supported by the HL-LHC project Crab cavities are a key element to achieve the HL-LHC performance goals. There are two types of cavities Double Quarter Wave (DQW) for vertical crabbing, and Radiofrequency Dipole (RFD) for horizontal crabbing. Cavities are hosted in a cryomodule to provide optimal conditions for their operation at 2K while minimizing the external thermal loads and stray magnetic fields. One crab cryomodule contains more than thirteen thousand components and the assembly procedure for the first DQW prototype was carefully planned and executed. It was installed in the SPS accelerator at CERN in 2018 and successfully tested with proton beams. A review has thus been performed right after completion of the assembly in order to gather all the experience acquired and improve accordingly the design of the next generation of crab cryomodules. A second cryomodule with two RFD cavities is currently under production. This paper presents the lessons learnt from the first assembly and their implementation to the design of the future crab cryomodules.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP099
About •	paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP100	Design Upgrades of the Next Superconducting RF Gun for ELBE	gun, SRF, cathode, cryomodule	326
	J. Teichert, A. Arnold, S. Ma, P. Murcek, J. Schaber, H. Vennekate, R. Xiang, P.Z. Zwartek HZDR, Dresden, Germany K. Zhou CAEP/IAE, Mianyang, Sichuan, People’s Republic of China
	Funding: Funding is provided by the China Scholarship Council. At the ELBE user facility a superconducting RF photoinjector has been in operation since several years. The injector is routinely applied for THz radiation production in user beam experiments. For future applications higher bunch charges, shorter pulses and lower transverse emittances are required. Thus it is planned to replace this SRF gun by a next version with an RF cavity reaching a higher acceleration gradient. We also present improvements concerning the SC solenoid and the photocathode exchange system and report on the status of construction and testing of this SRF gun cryomodule.
	Poster MOP100 [2.199 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP100
About •	paper received ※ 27 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP105	A Superconducting Magnetic Shield for the Photoelectron Injector of BERLinPro	solenoid, gun, shielding, operation	335
	J. Völker, A. Frahm, A. Jankowiak, S. Keckert, J. Knobloch, G. Kourkafas, O. Kugeler, A. Neumann, H. Plötz HZB, Berlin, Germany
	Magnetic fields are a big issue for SRF cavities, especially in areas with strong electromagnets or ferromagnetic materials. Magnetic shieldings consisting of metal alloys with high magnetic permeability are often used to reroute the external magnetic flux from the cavity region. Those Mu metal shields are typically designed for weak magnetic fields like Earth’s magnetic field. Next to strong magnetic field sources like superconducting (SC) solenoids, those shields can be easily saturated resulting in a degradation of the shielding efficiency and a permanent magnetization. For the photoinjector of BERLinPro a new SC solenoid will be installed inside the cryomodule next to the SRF gun cavity. Calculations show that the fringe fields of the solenoid during operation can saturate the cavity Mu-metal shields. Therefore we designed an SC magnetic shield placed between solenoid and cavity shield to protect the latter during magnet operation. In this paper we will present the design and first measurements of this SC magnetic shield.
	Poster MOP105 [2.011 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP105
About •	paper received ※ 04 July 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUA1	The Field-Dependent Surface Resistance of Doped Niobium: New Experimental and Theoretical Results	SRF, niobium, electron, ECR	340
	J.T. Maniscalco, M. Ge, P.N. Koufalis, M. Liepe Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA T. Arias, D. Liarte, J.P. Sethna, N. Sitaraman Cornell University, Ithaca, New York, USA
	We present systematic work investigating how different doping and post-doping treatments affect the BCS surface resistance at 1.3~GHz and higher frequencies. We examine the field-dependent BCS resistance at many temperatures as well as the field-dependent residual resistance and use the results to reveal how impurity species and concentration levels affect the field-dependent RF properties. We further demonstrate the importance of thermal effects and their direct dependence on doping level. We use the tools of Density Functional Theory to work towards an {\em ab initio} model of electron overheating to theoretically confirm the impact of doping, create a full model that includes thermal effects to predict the field dependent resistance, and show that the predictions of the model agree with results from doped and non-doped cavities ({\em e.g.} the strength of the anti-Q-slope and the high-field Q slope). Finally, we use our experimental results to systematically assess and compare theories of the field-dependent BCS resistance, showing that the current theory on smearing of the density of states is incomplete.
	Slides TUFUA1 [6.780 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUFUA1
About •	paper received ※ 01 July 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUA4	New Insights on Nitrogen Doping	electron, SRF, ECR, niobium	347

Paper

Title

Other Keywords

Page

MOFAA1

LCLS-II: Status, Issues and Plans

SRF, cryomodule, linac, FEL

1

M.C. Ross
SLAC, Menlo Park, California, USA

Funding: Work supported by Department of Energy contract DE-AC02-76SF00515
The Linac Coherent Light Source II (LCLS-II) project requires the assembly, test, and installation of 37 cryomodules (CM) in order to deliver a 4 GeV CW electron beam to the FEL undulators for production of both hard and soft X-ray pulses at a repetition rate of up to 1 MHz. SRF cavity performance in the 30+ tested CM exceeds gradient and cryogenic dynamic heat-load requirements (set at 16 MV/m and 10 W resp). In this talk we present microphonics, shipping, magnetic-flux exclusion, and field emission performance. The US funding agency, DOE, has recently approved an additional 20 CM for the extension of LCLS-II to 8 GeV. This paper will also include initial cavity and heat-load performance results for the extension project, LCLS-II-HE.

Slides MOFAA1 [30.146 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOFAA1

About •

paper received ※ 25 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOFAA2

Operation of the European XFEL Towards the Maximum Energy

electron, FEL, operation, MMI

9

M. Omet, V. Ayvazyan, J. Branlard, S. Choroba, W. Decking, V.V. Katalev, D. Kostin, L. Lilje, P. Morozov, Y. Nachtigal, H. Schlarb, V. Vogel, N. Walker, B. Yildirim
DESY, Hamburg, Germany

After the initial commissioning of the available 25 radio frequency (RF) stations of the European XFEL (RF gun, A1, AH1 and stations A2 through A23) a maximum electron beam energy of 14.5 GeV was achieved, 3 GeV short of the design energy of 17.5 GeV. In order to tackle this problem, the Maximum Gradient Task Force (MGTF) was formed. In the scope of the work of the MGTF, RF stations A6 through A25 (linac L3) were systematically investigated and voltage-limiting factors of the SRF accelerating modules and their RF distribution system were identified and improved. As a result, the design electron beam energy was exceeded at 17.6 GeV on the 18.7.2018. Beside this an overview over the regular RF operation at the European XFEL is given.

Slides MOFAA2 [5.695 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOFAA2

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOFAA3

The FRIB SC-Linac - Installation and Phased Commissioning

cryomodule, MMI, linac, cryogenics

12

J. Wei, H. Ao, S. Beher, B. Bird, N.K. Bultman, F. Casagrande, D. Chabot, W. Chang, S. Cogan, C. Compton, J. Curtin, K.D. Davidson, E. Daykin, K. Elliott, A. Facco, A. Fila, V. Ganni, A. Ganshyn, P.E. Gibson, T. Glasmacher, I. Grender, W. Hartung, L. Hodges, K. Holland, H.-C. Hseuh, A. Hussain, M. Ikegami, S. Jones, T. Kanemura, S.H. Kim, P. Knudsen, M.G. Konrad, J. LeTourneau, Z. Li, S.M. Lidia, G. Machicoane, P. Manwiller, F. Marti, T. Maruta, E.S. Metzgar, S.J. Miller, D.G. Morris, C. Nguyen, K. Openlander, P.N. Ostroumov, A.S. Plastun, J.T. Popielarski, L. Popielarski, J. Priller, M.A. Reaume, H.T. Ren, T. Russo, K. Saito, M. Shuptar, J.W. Stetson, D.R. Victory, R. Walker, X. Wang, J.D. Wenstrom, M. Wright, M. Xu, T. Xu, Y. Yamazaki, Q. Zhao, S. Zhao
FRIB, East Lansing, Michigan, USA
K. Dixon, M. Wiseman
JLab, Newport News, Virginia, USA
A. Facco
INFN/LNL, Legnaro (PD), Italy
K. Hosoyama
KEK, Ibaraki, Japan
M.P. Kelly
ANL, Lemont, Illinois, USA
R.E. Laxdal
TRIUMF, Vancouver, Canada

Funding: Work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661.
The Facility for Rare Isotope Beams (FRIB) superconducting (SC) driver linac is designed to accelerate all stable ions including uranium to energies above 200 MeV/u primarily with 46 cryomodules containing 324 quarter-wave resonators (QWR) and half-wave (HWR) resonators. With the newly commissioned helium refrigeration system supplying liquid helium to the QWR and solenoids, heavy ion beams including Ne, Ar, Kr and Xe were accelerated to the charge stripper location above 20 MeV/u with the first linac segment consisting of 15 cryomodules containing 10⁴ QWRs of β=0.041 and 0.085 and 39 solenoids. Installation of cryomodules with β=0.29 and 0.53 HWRs is proceeding in parallel. Development of β=0.65 elliptical resonators is on-going supporting the FRIB energy upgrade to 400 MeV/u. This paper summarizes the SC-linac installation and phased commissioning status that is on schedule and on budget to the FRIB project.

Slides MOFAA3 [46.571 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOFAA3

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP003

Development of Nb₃Sn Cavity Coating at IMP

niobium, SRF, radio-frequency, experiment

21

Z.Q. Yang, H. Guo, Y. He, C.L. Li, Z.Q. Lin, M. Lu, T. Tan, P.R. Xiong, S.H. Zhang, S.X. Zhang
IMP/CAS, Lanzhou, People’s Republic of China

The A15 superconductor Nb₃Sn is one of the most promising alternative materials to standard niobium for SRF applications. In this paper, we report our progress in the development of Nb₃Sn cavity coating by vapor diffusion method at IMP. The evolutionary process of nucleation was analyzed. Influence of S_nCl₂ partial pressure inhomogeneity was studied. Less-nuclear zones were found on the surfaces of nucleation samples. The Nb₃Sn film structure and composition were investigated and analyzed. In light of knowledge obtained above, the coating process was optimized. Finally, both 1.3 GHz and 650 MHz single cell cavities were coated and vertically tested both at 4 K and 2 K. Effect of low temperature baking (1000°C for 48 hs) on the RF performance of Nb₃Sn cavity was studied. After baking, the Q drop in the low field region was eliminated and the Q in the intermediate field region was increased 8 times. The Q was 10 times larger than that of the Nb cavity at 4.2 K even in the case of the ambient field larger than 20 mGs. This study shows that the low temperature baking is an effective enrichment to the post treatment of the Nb₃Sn cavity.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP003

About •

paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP005

The Facility for Rare Isotope Beams Superconducting Cavity Production Status and Findings Concerning Surface Defects

linac, SRF, niobium, status

31

C. Compton
NSCL, East Lansing, Michigan, USA
H. Ao, J. Asciutto, K. Elliott, W. Hartung, S.H. Kim, E.S. Metzgar, S.J. Miller, J.T. Popielarski, L. Popielarski, K. Saito, T. Xu
FRIB, East Lansing, Michigan, USA
J. Craft
SLAC, Menlo Park, California, USA

Funding: This material is based upon work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661
The Facility for Rare Isotope Beams (FRIB), located on the campus of Michigan State University (MSU) will require 324 Superconducting Radio Frequency (SRF) cavities in the driver linac. Four types of cavities of two classes, quarter-wave (β=0.041 and 0.085) and half-wave (β=0.29 and 0.53), will be housed in 46 cryomodules. To date, FRIB has tested over 300 cavities in vertical Dewar tests as part of the certification procedures. Incoming cavities, fabricated in industry, are sequenced through acceptance inspection and checked for non-conformance. If accepted, the cavities are processed, assembled onto a vertical test stand, and cold tested. A large database of cavity surface images has been collected with the aid of a borescope camera. Borescope inspection is a standard step that is performed at incoming inspection, post-acid bulk etch, and after failed tests (if necessary) for each cavity, in order to locate any non-conformances. Findings of surface defects relating to degraded cavity performance will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP005

About •

paper received ※ 02 July 2019 paper accepted ※ 13 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP007

400 MHz Seamless Copper Cavity in the Framework of FCC Study

ISOL, superconductivity, framework, status

36

O. Azzolini, G. Keppel, C. Pira
INFN/LNL, Legnaro (PD), Italy

In the framework of the FCC study the production of 400 MHz copper cavities is one of the key challenges for the development of more efficient superconducting RF cavities. Any progress on substrate manufacturing and preparation will have an immediate impact on the final RF performance, as it was demonstrated by the seamless cavities produced for the HIE-ISOLDE project. Spinning is a potential alternative to conventional production methods of copper single and multi-cells. In this work is presented the first 400 MHz copper SRF cavity prototype produced via Spinning at Laboratori Nazionali di Legnaro of INFN. The production process is explained starting from a copper foil of 1000 mm diameter and 4mm thick to arrive to a seamless 400 MHz cavity. Moreover, the metrology of the cavity and the analysis of the influence of intermediate thermal treatments among each steps of cold work are shown.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP007

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP010

Ab Initio Calculations on the Growth and Superconducting Properties of Nb₃Sn

site, niobium, SRF, electron

39

N. Sitaraman, T. Arias, P. Cueva, M.M. Kelley, D.A. Muller
Cornell University, Ithaca, New York, USA
J.M. Carlson, A.R. Pack, M.K. Transtrum
Brigham Young University, Provo, USA
M. Liepe, R.D. Porter, Z. Sun
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA

Funding: This research was funded by the Center for Bright Beams.
In this work, we employ theoretical ab initio techniques to solve mysteries and gain new insights in Nb₃Sn SRF physics. We determine the temperature dependence of Nb₃Sn antisite defect formation energies, and discuss the implications of these results for defect segregation. We calculate the phonon spectral function for Nb₃Sn cells with different combinations of antisite defects and use these results to determine Tc as a function of stoichiometry. These results allow for the first-ever determination of Tc in the tin-rich regime, where experimental measurements are unavailable and which is critical to understanding the impact of tin-rich grain boundaries on superconducting cavity performance. Finally, we propose a theory for the growth mechanism of Nb₃Sn growth on a thick oxide, explaining the puzzling disappearing droplet behavior of Sn on Nb oxide and suggesting how in general an oxide layer reacts with Sn to produce a uniform Nb₃Sn layer.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP010

About •

paper received ※ 02 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP011

High Frequency Nb₃Sn Cavities

SRF, niobium, radio-frequency, factory

44

R.D. Porter, M. Liepe, J.T. Maniscalco
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA

Niobium-3 Tin (Nb₃Sn) is an alternative material to Nb for SRF cavities. This material is capable of higher temperature operation and has high theoretical maximum accelerating gradients. Cornell University is a leader in the development of this material for SRF applications, and current Nb₃Sn 1.3 GHz single cells produced at Cornell achieve quality factors above 10^zEhNZeHn at 4.2 K at medium fields, far above what can be reached with niobium. Most of the recent Nb₃Sn cavity development has been done at 1.3 GHz. In this paper, we present new results from Nb₃Sn cavities at 2.6 GHz and 3.9 GHz. We compare relative cavity performance and flux trapping sensitivities, and extract frequency dependencies. Results show that the frequency can be increased without degrading the performance of the cavities, opening the path towards a new generation of compact and efficient SRF cavities for a wide range of future applications.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP011

About •

paper received ※ 05 July 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP013

Reducing Surface Roughness of Nb₃Sn Through Chemical Polishing Treatments

niobium, superconductivity, controls, SRF

48

H. Hu, M. Liepe, R.D. Porter
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA

Niobium-3 tin (Nb₃Sn) is a promising alternative material for SRF cavities, with theoretical limits for critical temperatures and superheating fields reaching twice that of conventional Nb cavities. However, currently achievable accelerating gradients in Nb₃Sn cavities are much lower than their theoretical limit. One limitation to the maximum accelerating gradient is surface magnetic field enhancement caused by the surface roughness of Nb₃Sn. However, there are currently no standard techniques used to reduce Nb₃Sn surface roughness. Since Nb₃Sn is only 2-3 microns thick, it is difficult to selectively polish Nb₃Sn without removing the entire layer. Here, we investigate reducing the surface roughness of Nb₃Sn through applying chemical polishing treatments, including modified versions of standard techniques such as Buffered Chemical Polishing (BCP) and Electropolishing (EP). Through data acquired from Atomic Force Microscope (AFM) scans, SEM scans, and SEM-EDS analysis, we show the effects of these chemical treatments in reducing surface roughness and consider the changes in the chemical composition of Nb₃Sn that may occur through the etching process. We find that BCP with a 1:1:8 solution is ineffective while EP halves the surface roughness of Nb₃Sn.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP013

About •

paper received ※ 01 July 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP014

Electroplating of Sn Film on Nb Substrate for Generating Nb₃Sn Thin Films and Post Laser Annealing

laser, radio-frequency, electron, HOM

51

Z. Sun, M. Liepe, T.E. Oseroff, R.D. Porter
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
T. Arias, A.B. Connolly, J.M. Scholtz, N. Sitaraman, M.O. Thompson
Cornell University, Ithaca, New York, USA
X. Deng
University of Virginia, Charlottesville, Virginia, USA
K.D. Dobson
University of Delaware, Newark, Delaware, USA

Controlling film quality of Nb₃Sn is critical to its SRF cavity performance. The state-of-the-art vapor diffusion approach for Nb₃Sn deposition observed surface roughness, thin grain regions, and misfit dislocations which negatively affect the RF performance. The Sn deficiency and non-uniformity at the nucleation stage of vapor deposition is believed to be the fundamental reason to cause these roughness and defects issues. Thus, we propose to pre-deposit a uniform Sn film on the Nb substrate, which is able to provide sufficient Sn source during the following heat treatment for Nb₃Sn nucleation and growth. Here, we demonstrated successful electrodeposition of a low-roughness, dendrite-free, excellent-adhesion Sn film on the Nb substrate. More importantly, we further achieved a uniform, low-roughness (Ra = 66 nm), pure-stoichiometric Nb₃Sn film through thermal treatment of this electroplated Sn film in the furnace. Additionally, we provide preliminary results of laser annealing as a post treatment for epitaxial grain growth and roughness reduction.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP014

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP015

RF Performance Sensitivity to Tuning of Nb₃Sn Coated CEBAF Cavities

simulation, SRF, experiment, factory

55

G.V. Eremeev, W. Crahen, J. Henry, F. Marhauser, C.E. Reece
JLab, Newport News, Virginia, USA
U. Pudasaini
The College of William and Mary, Williamsburg, Virginia, USA

Funding: Co-Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. Based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics.
Nb₃Sn has the potential to surpass niobium as the material of choice for SRF applications. The potential of this material stems from a larger superconducting energy gap, which leads to expectations of a higher RF critical field and a lower RF surface resistance. The appeal of better superconducting properties is offset by the relative complexity of producing practical Nb₃Sn structures, and Nb₃Sn sensitivity to lattice disorder challenges the use of the material for practical applications. Such sensitivity is indirectly probed during SRF cavity development, when the cavity is tuned to match the desired accelerator frequency. In the course of recent experiments we have coated and tuned several multi-cell cavities. Cold RF measurements before and after tuning showed degradation in cavity performance after tuning. The results of RF measurement were compared against strain evolution on Nb₃Sn surface during tuning based on CST and ANSYS models.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP015

About •

paper received ※ 26 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP016

Insights Into Nb₃Sn Coating of CEBAF Cavities From Witness Sample Analysis

niobium, SRF, HOM, hardware

60

G.V. Eremeev, M.J. Kelley, C.E. Reece
JLab, Newport News, Virginia, USA
M.J. Kelley, U. Pudasaini
The College of William and Mary, Williamsburg, Virginia, USA

Funding: Co-Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. Based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics.
With the progress made in the Nb₃Sn coatings on single-cell SRF cavities, development is ongoing to reproduce single-cell cavity results on practical structures such as CEBAF 5-cell cavities. During CEBAF cavity coating development, several changes from the single-cell procedure to the coating setup and the heating profile were introduced to improve the quality of Nb₃Sn films. To witness the properties of grown Nb₃Sn films in different cavity locations, 10 mm x 10 mm samples were positioned in strategic places within the coating chamber. Composition and structure of the samples were analyzed with surface analytic techniques and correlated with sample location during coatings. Implications from sample analysis to Nb₃Sn coatings on different geometries are discussed in this contribution.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP016

About •

paper received ※ 26 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP018

Recent Results From Nb₃Sn Single Cell Cavities Coated at Jefferson Lab

SRF, experiment, factory, niobium

65

U. Pudasaini, M.J. Kelley
The College of William and Mary, Williamsburg, Virginia, USA
G. Ciovati, G.V. Eremeev, M.J. Kelley, C.E. Reece
JLab, Newport News, Virginia, USA
I.P. Parajuli, Md.N. Sayeed
ODU, Norfolk, Virginia, USA

Funding: Partially authored by Jefferson Science Associates under contract no. DE¬AC05¬06OR23177. Supported by Office of High Energy Physics under grants DE-SC-0014475 to the College of William and DE-SC-0018918 to Virginia Tech
Because of superior superconducting properties (Tc ~ 18.3K, Hs h ~ 425 mT and delta ~ 3.1 meV) compared to niobium, Nb₃Sn promise better RF performance (Q₀ and E_acc) and/or higher operating temperature (2 K Vs 4.2 K) for SRF cavities. Nb₃Sn-coated SRF cavities are produced routinely by depositing a few micron-thick Nb₃Sn films on the interior surface of Nb cavities via tin vapor diffusion technique. Early results from Nb₃Sn cavities coated with this technique exhibited precipi-tous low field Q-slope, also known as Wuppertal slope. Several Nb₃Sn single cell cavities coated at JLab ap-peared to exhibit similar Q-slope. RF testing of cavi-ties and materials study of witness samples were con-tinuously used to modify the coating protocol. At best condition, we were able to produce Nb₃Sn cavity with Q₀ in excess of ~ 5×10¹⁰ at 2 K and ~ 2×1010 at 4 K up the accelerating gradient of ~15 MV/m, without any significant Q-slope. In this presentation, we will dis-cuss recent results from several Nb₃Sn coated single-cell cavities linked with material studies of witness samples, coating process modifications and the possi-ble causative factors to Wuppertal slope.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP018

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP019

Surface Preparation and Optimization of SC CH Cavities

operation, linac, coupling, ECR

71

P. Müller, M. Basten, M. Busch, T. Conrad, H. Podlech
IAP, Frankfurt am Main, Germany
K. Aulenbacher, F.D. Dziuba, M. Miski-Oglu
HIM, Mainz, Germany
W.A. Barth
GSI, Darmstadt, Germany

The Institute of Applied Physics (IAP) introduced the superconducting multi-gap CH-structure, which is mainly designed for low beta hadron acceleration. In 2017, a 217 MHz sc CH-structure was successfully tested with beam at GSI and multiple CH-structures are currently under development for the GSI cw linac. RF performance of all sc cavities are limited by the surface properties of the used material. Therefore, sufficient surface preparation and optimization is necessary to achieve optimal performance. Presently as standard procedure BCP and HPR is used for CH-cavities. Several surface treatments will be applied to the very first CH-prototype, a 360 MHz, 19-cell cavity. Prior to the first treatment, the status of the cavity was examined, including leak tests and performance tests at 4 and 2 K. This paper presents the performance development of a sc CH cavity depending on different preparation methods.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP019

About •

paper received ※ 23 June 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP022

Superconducting RF Cavity Materials Research at the S-DALINAC

niobium, linac, SRF, simulation

74

R. Grewe, L. Alff, M. Arnold, J. Conrad, S. Flege, M. Major, N. Pietralla
TU Darmstadt, Darmstadt, Germany
F. Hug
IKP, Mainz, Germany

Funding: Supported by BMBF Through 05H18RDRB2
Current state-of-the-art superconducting rf (srf) accelerators are mostly using cavities made of high RRR bulk niobium (Nb). The maximum field gradients and quality factors (Q₀) of these cavities are basically reached now. To further increase the srf cavity properties for future accelerator facilities, research of new materials for srf cavity applications is necessary. The current research at the S-DALINAC* is focused on the development of bake-out procedures of Nb samples and cavities in nitrogen (N) atmosphere of up to 100 mbar to nucleate the delta-phase (d-phase) of the Nb-N binary system. The d-phase has superconducting properties which exceed the properties of bulk Nb. This makes the d-phase attractive for srf applications. The vertical test cryostat (vt) at the S-DALINAC has been upgraded and recommissioned to allow investigations of the quality factor and accelerating field gradients of cavities before and after bake-out. The vt upgrade includes a newly developed variable input coupling to allow matching of the external q-factor (Qex) to Q₀. The results of the ongoing research of the nitrogen atmosphere bake-out procedures and the upgrade of the vt will be presented.
*N. Pietralla, Nuclear Physics News, Vol. 28, No. 2, 4 (2018)

Poster MOP022 [1.759 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP022

About •

paper received ※ 21 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP023

Nitrogen Infusion Sample R&D at DESY

niobium, vacuum, SRF, HOM

77

C. Bate, A. Dangwal Pandey, A. Ermakov, B. Foster, T.F. Keller, D. Reschke, J. Schaffran, S. Sievers, N. Walker, H. Weise, M. Wenskat
DESY, Hamburg, Germany
W. Hillert
University of Hamburg, Institut für Experimentalphysik, Hamburg, Germany
G.D.L. Semione, V. Vonk
DESY Nanolab, FS-NL, Hamburg, Germany
A. Stierle
University of Hamburg, Hamburg, Germany

The European XFEL continuous wave upgrade requires cavities with reduced surface resistance (high Q-values) for high duty cycle while maintaining high accelerating gradient for short-pulse operation. A possible way to meet the requirements is the so-called nitrogen infusion procedure. However, a fundamental understanding and a theoretical model of this method are still missing. The approach shown here is based on sample R&D, with the goal to identify key parameters of the process and establish a stable, reproducible recipe. To understand the underlying processes of the surface evolution, which gives improved cavity performance, advanced surface analysis techniques (e.g. SEM/EDX, TEM, XPS, TOF-SIMS) are utilized. Additionally, a small furnace just for samples was set up to change and explore the parameter space of the infusion recipe. Results of these analyses, their implications for the cavity R&D and next steps are presented.

Poster MOP023 [3.759 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP023

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP024

Vacancy-Hydrogen Dynamics in Samples During Low Temperature Baking

positron, niobium, lattice, electron

83

M. Wenskat, C. Bate, D. Reschke, H. Weise
DESY, Hamburg, Germany
C. Bate
University of Hamburg, Hamburg, Germany
M. Butterling, E. Hirschmann, M.O. Liedke, A. Wagner
HZDR, Dresden, Germany
J. Cizek
Charles University, Prague, Czech Republic

Funding: This work was supported by the Helmholtz Association within the topic Accelerator Research and Development (ARD) of the Matter and Technologies (MT) Program and by the BMBF under the research grant 05H18GURB1.
The recent discovery of a modified low temperature baking process lead to a reduction of surface losses and an increase of the accelerating gradient of TESLA shape cavities. The hypothesis linking the accelerator performance and the treatment is the suppression of lossy nanohydrides via defect trapping, with vacancy-hydrogen complexes forming at the lower temperatures. Utilizing Doppler broadening Positron Annihilation Spectroscopy and Positron Annihilation Lifetime Spectroscopy samples made from European XFEL niobium sheets and cavity cut-outs were investigated. The evolution of vacancies, hydrogen and their interaction at different temperature levels have been studied during in-situ annealing. Measurements of niobium samples and a correlation between RF, material properties, and V-H distribution in cavity cut-outs has been done.

Poster MOP024 [1.087 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP024

About •

paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP025

Cavity Cut-out Studies of a 1.3 GHz Single-cell Cavity After a Failed Nitrogen Infusion Process

niobium, SRF, electron, superconductivity

87

M. Wenskat, C. Bate, T.F. Keller, D. Reschke
DESY, Hamburg, Germany
C. Bate
University of Hamburg, Hamburg, Germany
A. Jeromin
DESY Nanolab, FS-NL, Hamburg, Germany
J. Knobloch, F. Kramer, O. Kugeler, J.M. Köszegi
HZB, Berlin, Germany
J. Knobloch
University of Siegen, Siegen, Germany

Funding: This work was supported by the Helmholtz Association within the topic Accelerator Research and Development (ARD) of the Matter and Technologies (MT) Program and by the BMBF under the research grant 05H18GURB1.
R&D on the nitrogen infusion process at DESY produced at the beginning a series of 1.3 GHz single-cell cavities which have shown severe deterioration in the vertical cold test which was completely unexpected and could not be explained. To investigate the reason for the deterioration, one of those cavities was optically inspected and a T- and H-Map test was done in collaboration with HZB. Together with 2nd Sound data, regions of interests were identified and cut from the cavity. Subsequent surface analysis techniques (SEM/EDX, SIMS, PIXE, EBSD, DB-PAS, PALS, XPS) were applied in order to identify the reason for the deterioration. Especially the differences between hot and cold spots as well as quench spots identified by T-Mapping were investigated.

Poster MOP025 [0.975 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP025

About •

paper received ※ 20 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP026

A Cross-Lab Qualification of Modified 120°C Baked Cavities

shielding, multipactoring, factory, niobium

90

M. Wenskat, D. Reschke, J. Schaffran, L. Steder, M. Wiencek
DESY, Hamburg, Germany
D. Bafia, A. Grassellino, O.S. Melnychuk
Fermilab, Batavia, Illinois, USA
A.D. Palczewski
JLab, Newport News, Virginia, USA
M. Wiencek
IFJ-PAN, Kraków, Poland

Funding: This work was supported by the Helmholtz Association within the topic Accelerator Research and Development (ARD) of the Matter and Technologies (MT) Program and by the BMBF under the research grant 05H18GURB1.
Within a global effort to understand and standardize the nitrogen-infusion and the low T bake procedure, one large grain and two fine grain single-cell cavity were treated and tested at FNAL and then send to other labs including DESY and JLab for further studies.

Poster MOP026 [0.813 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP026

About •

paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP027

Study on Nitrogen Infusion using KEK New Furnace

injection, SRF, accelerating-gradient, vacuum

95

K. Umemori, E. Kako, T. Konomi, S. Michizono, H. Sakai
KEK, Ibaraki, Japan
T. Okada
Sokendai, Ibaraki, Japan
J. Tamura
JAEA/J-PARC, Tokai-mura, Japan

KEK has been carried out high-Q/high-G R&D, to realize high performance of SRF cavities toward ILC. KEK constructed a new furnace, which is dedicated for N-infusion studies. We performed more than 10 times of N-infusion trials using 1.3 GHz single-cell cavities. Some results showed better Q-values up to high field, however, some results showed degraded Q-E slopes probably due to contamination. Improvement of accelerating gradient is not observed at moment. We have tried to clean the furnace and Nitrogen injection line to reduce the effect of contamination. Details of procedures of N-infusion, results of vertical tests, condition of the furnace including RGA spectrum and Nb sample analysis results are shown.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP027

About •

paper received ※ 04 July 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP028

Materials Science Investigations of Nitrogen-Doped Niobium for SRF Cavities

niobium, SRF, superconducting-RF, collider

99

M. Major, L. Alff, M. Arnold, J. Conrad, S. Flege, R. Grewe, N. Pietralla
TU Darmstadt, Darmstadt, Germany

Funding: Work supported by the German Federal Ministry for Education and Research (BMBF) through grant 05H18RDRB2.
Niobium is the standard material for superconducting RF (SRF) cavities for particle acceleration. Superconducting materials with higher critical temperature or higher critical magnetic field allow cavities to work at higher operating temperatures or higher accelerating fields, respectively. Enhancing the surface properties of the superconducting material in the range of the penetration depth is also beneficial. One direction of search for new materials with better properties is the modification of bulk niobium by nitrogen doping. In the Nb-N phase diagram, the cubic delta-phase of NbN has the highest critical temperature. Niobium samples were annealed and N-doped in the high-temperature furnace at TU Darmstadt and investigated at its Materials Research Department with respect to structural modifications. Secondary ion mass spectrometry showed at which conditions N-diffusion takes place. X-ray diffraction (XRD) confirmed the appearance of NbN and Nb₂N phases for the optimized doping process. XRD pole figures also showed grain growth during sample annealing.

Poster MOP028 [2.555 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP028

About •

paper received ※ 05 July 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP029

N-Doping Studies With Single-Cell Cavities for the SHINE Project

niobium, SRF, FEL, ECR

102

J.F. Chen, H.T. Hou, Y.F. Liu, D. Wang, Y. Wang
SARI-CAS, Pudong, Shanghai, People’s Republic of China
Y.W. Huang
ShanghaiTech University, Shanghai, People’s Republic of China
Z. Wang
SINAP, Shanghai, People’s Republic of China

The SHINE SRF accelerator is designed to operate in CW mode with more than six hundred superconducting cavities. In order to reduce the high cost of construction and operation of the cryogenic system, high-Q cavities with nitrogen-doping technology together with tradition-ally treated large-grain cavities have been considered as two possible options. In this paper, we present N-doping studies on single-cell cavities fabricated with fine-grain and large-grain niobium.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP029

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP030

Analysis of Surface Nitrides Created During "Doping" Heat Treatments of Niobium

niobium, SRF, lattice, controls

106

J.K. Spradlin, A.D. Palczewski, C.E. Reece, H. Tian
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
The benefits of reduced RF losses from interstitial "doping" of niobium are well established. Many of the details involved in the process remain yet to be elucidated. The niobium surface reacted with low-pressure nitrogen at 800°C presents a surface with chemical reactivity different than standard niobium. While standard "recipes" are being used to produce cavities, we seek additional insight into the chemical processes that may be used to remove the "undesirable" as-formed surface layer. This may lead to new processing routes or quality assurance methods to build confidence that all surface "nitrides" have been removed. We report a series of alternate chemistry treatments and subsequent morphological examinations and interpret the results. We also introduce a new standardized Nb sample system in use for efficient characterization of varying doping protocols and cross-laboratory calibration.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP030

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP031

Investigation of Frequency Behavior Near Tc of Niobium Superconducting Radio-Frequency Cavities

SRF, niobium, electron, ECR

112

D. Bafia, J. Zasadzinski
IIT, Chicago, Illinois, USA
D. Bafia, M. Checchin, A. Grassellino, O.S. Melnychuk, A.S. Romanenko, D.A. Sergatskov
Fermilab, Batavia, Illinois, USA

This paper will present a systematic investigation of the resonant frequency behavior of niobium SRF cavities subject to different surface processing (nitrogen doping, nitrogen infusion, 120°C bake, EP, etc.) near the critical transition temperature. We find features occurring in frequency versus temperature (FvsT) data near Tc that seem to vary with surface processing. Emphasis is placed on one of the observed features: a dip in the superconducting resonant frequency below the normal conducting value which is prominent in nitrogen doped cavities and appears to be a signature of nitrogen doping. This gives further insights on the mechanisms responsible for the large increase in performance of cavities subject to this surface treatment. The magnitude of this dip in frequency is studied and related to possible physical parameters such as the concentration of impurities near the surface and the design resonant frequency of the cavity. A possible explanation for the meaning of this dip is discussed, namely, that it is a result of strong coupling between electrons and phonons within the resonator.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP031

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP032

Effect of Low Temperature Infusion Heat Treatments and "2/0" Doping on Superconducting Cavity Performance

ECR, niobium, SRF, background

118

P.N. Koufalis, M. Ge, M. Liepe, J.T. Maniscalco
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA

Under specific circumstances, low temperature infusion heat treatments of niobium cavities have resulted in the ubiquitous "Q-rise". This is an increase in quality factor with increasing field strength or equivalently a decrease in the temperature-dependent component of the surface resistance. We investigate the results of various infusion conditions with infusion bake time as a free parameter. To study the very near surface effects of infusion, we employ HF rinsing, light VEP, and oxypolishing to remove several or tens of nm at a time. We present results from RF performance tests of low temperature infusion heat treated niobium cavities, and correlate these with SIMS impurity depth profiles obtained from witness samples. We also present results of a cavity doped at 800 C with the "2/0" recipe.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP032

About •

paper received ※ 26 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP033

The Beam Dynamics Updates of the Fermilab PIP-II 800 MeV Superconducting Linac

linac, SRF, optics, emittance

123

A. Saini, V.P. Yakovlev
Fermilab, Batavia, Illinois, USA
E. Pozdeyev
FRIB, East Lansing, Michigan, USA

The Proton Improvement Plan (PIP) -II is a high intensity proton facility being developed to support a neutrino program over the next two decades at Fermilab. At its core is the design and construction of a Continuous Wave compatible superconducting radio frequency linear accelerator that would accelerate an average beam current of 2 mA up to 800 MeV. This paper presents recent updates in the beam dynamics leading to a reliable and robust linac design and simplifying the cryo-module assembly.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP033

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP034

European XFEL: Accelerating Module Repair at DESY

FEL, linac, SRF, operation

127

D. Kostin, J. Eschke, K. Jensch, N. Krupka, D. Reschke, S. Saegebarth, J. Schaffran, M. Schalwat, P. Schilling, M. Schmökel, S. Sievers, N. Steinhau-Kühl, E. Vogel, H. Weise, M. Wiencek, B. van der Horst
DESY, Hamburg, Germany

The European XFEL is in operation since 2017. The design projected energy of 17.5 GeV was reached, even with the last 4 main linac accelerating modules not yet installed. 2 out of 4 not installed modules did suffer from strong cavity performance degradation, namely increased field emission, and required surface processing. The first of two modules is reassembled and tested. The module test results confirm a successful repair action. The module repair and test steps are described together with cavities performance evolution.

Poster MOP034 [1.863 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP034

About •

paper received ※ 17 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP035

Cryogenic Infrastructure at BESSY II – Current Installations and Future Developments

cryogenics, storage-ring, gun, radiation

131

S. Heling, W. Anders, J. Heinrich, A. Hellwig, K. Janke, S. Rotterdam
HZB, Berlin, Germany

In Berlin-Adlershof the Helmholtz-Zentrum Berlin (HZB) is operating the synchrotron radiation source BESSY II. Two superconducting wave-length shifter magnets are built-in the storage ring of BESSY II which are cooled with liquid helium. Additionally several test facilities for superconducting cavities are operated at HZB needing helium at 1.8 K. The required helium is supplied by two helium liquefiers. Parallel to operation of the existing facilities the BERLinPro project will qualify as test facility for ERL science and technology. In order to guarantee the required supply with helium at different temperature levels one of the existing helium liquefiers has been relocated to the new accelerator building and the existing cryogenic infrastructure has been upgraded with a new 10 000 L dewar, three valve boxes, a cold compressor box, warm pumps and a 80 K helium system. This paper specifies the setup of the above described helium cryoplants in detail and gives insight into the challenges of development. The paper concludes with an outlook of the upcoming developments of the cryogenic infrastructure at HZB.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP035

About •

paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP036

Microphonics Suppression Study in ARIEL e-Linac Cryomodules

cryomodule, GUI, linac, pick-up

136

Y. Ma, K. Fong, J.J. Keir, D. Kishi, S.R. Koscielniak, D. Lang, R.E. Laxdal, S.L. Liu, R.S. Sekhon, X. Wang
TRIUMF, Vancouver, Canada

Now the stage of the 30 MeV portion of ARIEL (The Advanced Rare Isotope Laboratory) e-Linac (1.3 GHz, SRF) is under commissioning which includes an injector cryomodule (ICM) with a single nine-cell cavity and the 1st accelerator cryomodule (ACM1) with two cavities configuration. The two ACM1 cavities are driven by a single klystron with vector-sum control and running in CW mode. We have observed a ponderomotive instability in ACM1 driven by the Lorentz force and seeded through microphonics that impacts beam stability [1-5]. Extensive damping has been implemented during a recent shut-down. The beam test results show 20 MeV acceleration gain can be reached by ACM1. A fast piezoelectric (Pie-zo) tuner is under development to allow a fast tuning compensation for the e-Linac cavities. In this paper, the progress of the microphonics suppression of Cryomod-ules is presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP036

About •

paper received ※ 24 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP039

Nitrogen Doping Studies of Superconducting Cavities at Peking University

niobium, accelerating-gradient, superconducting-cavity, ECR

141

S. Chen, M. Chen, L.W. Feng, J.K. Hao, L. Lin, K.X. Liu, S.W. Quan, F. Wang, F. Zhu
PKU, Beijing, People’s Republic of China

Nitrogen doping studies with 1.3 GHz superconducting cavities were carried out at Peking University in recent years. We have realized 4×10¹⁰ of high quality factor at 12 MV/m and 2.0 K with large grain single cell cavities by heavy doping. To improve the accelerating gradient of high Q cavities, light doping recipe is adopted. Accelerating gradient is improved to 20 MV/m and the quality factor is larger than 3×10¹⁰ at 16 MV/m and 2.0 K for light doped cavities. The nitrogen treatment, test and analysis are presented in this paper.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP039

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP040

Low Temperature Thermal Conductivity of Niobium and Materials for SRF Cavities

niobium, SRF, experiment, controls

144

M. Fouaidy
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France

A test facility, allowing the test of 4 samples simultaneously during each run, was developed for measuring at low temperature (T= 1.5 K - 10 K) the thermal conductivity k(T) of niobium and other materials used for the fabrication of SRF cavities. The measurements are performed using steady-state axial heat flow method with a careful control of heat leaks to the surrounding. Several samples of different materials (industrial Nb sheets, Ti¿) were either tested as received or/and subjected to various Heat Treatment (H.T) prior to the experiment then tested. The resulting experimental data are presented and compared to the experimental results previously reported by other groups. As expected, H.T @ 1200°C with Ti gettering improves the Nb RRR by a factor of 3 and consequently k(T). Finally, the correlation between the Niobium RRR and the thermal conductivity. at T=4.2 K is confirmed in good agreement with the Wiedemann-Franz law.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP040

About •

paper received ※ 04 July 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP045

The LCLS-II HE High Q and Gradient R&D Program

SRF, cryomodule, linac, niobium

154

D. Gonnella, S. Aderhold, A. Burrill, G.R. Hays, T.O. Raubenheimer, M.C. Ross
SLAC, Menlo Park, California, USA
D. Bafia, M. Checchin, A. Grassellino, M. Martinello, A.S. Romanenko
Fermilab, Batavia, Illinois, USA
M. Ge, M. Liepe, S. Posen
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
A.D. Palczewski, C.E. Reece
JLab, Newport News, Virginia, USA

Funding: US DOE and the LCLS-II HE Project
The LCLS-II HE project is a high energy upgrade to the superconducting LCLS-II linac. It consists of adding twenty additional 1.3 GHz cryomodules to the linac, with cavities operating at a gradient of 20.8 MV/m with a Q₀ of 2.7·10¹⁰. Performance of LCLS-II cryomodules has suggested that operations at this high of a gradient will not be achievable with the existing cavity recipe employed. Therefore a research program was developed between SLAC, Fermilab, Thomas Jefferson National Accelerator Facility, and Cornell University in order to improve the cavity processing method of the SRF cavities and reach the HE goals. This program explores the doping regime beyond what was done for LCLS-II and also has looked to further developed nitrogen-infusion. Here we will summarize the results from this R\&D program, showing significant improvement on both single-cell and 9-cell cavities compared with the original LCLS-II cavity recipe.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP045

About •

paper received ※ 25 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP047

Progress of IFMIF/EVEDA Project and Prospects for A-FNS

neutron, rfq, radiation, SRF

159

S. Ishida, A. Kasugai, K. Sakamoto
QST, Aomori, Japan
P. Cara
IFMIF/EVEDA, Rokkasho, Japan
H. Dzitko
F4E, Germany

International Fusion Materials Irradiation Facility (IFMIF) is an accelerator-based D-Li neutron source, in which two 40 MeV Deuteron(D) beams with a total current 250 mA impact on a liquid Li stream flowing at 15 m/s. In the IFMIF/EVEDA project under the Broader Approach (BA) agreement, the Li target was continuously operated with the cold trap and satisfied the stability requirement throughout the continuous operation. The Linear IFMIF Prototype Accelerator (LIPAc) is currently under development in Rokkasho, Japan, to demonstrate the 9 MeV/125 mA D⁺ beam acceleration. Recently, the first proton beam was injected into the RFQ with more than 90 % of transmission, followed by the first D⁺ beam accelerated at 5 MeV. The SRF linac necessary for the 9-MeV D⁺ beam is nearing completion of the manufacturing phase and will be assembled in Rokkasho. Based on these results, a conceptual design of the Advanced Fusion Neutron Source (A-FNS) for its construction in Rokkasho is underway to obtain material irradiation data for a DEMO reactor. The A-FNS is designed to be composed of an accelerator facility with a 40 MeV/125 mA D⁺ beam, a test facility including a liquid Li target system and a post irradiation examination facility, and to enable multipurpose utilization for neutron application.

Poster MOP047 [2.327 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP047

About •

paper received ※ 29 June 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP049

Prototypes Fabrication of 1.3 GHz Superconducting Rf Components for SHINE

FEL, niobium, HOM, SRF

164

H.T. Hou, J.F. Chen, Z.Y. Ma, J. Shi, Y. Wang
SARI-CAS, Pudong, Shanghai, People’s Republic of China
F.S. He
IHEP, Beijing, People’s Republic of China
S.W. Quan
PKU, Beijing, People’s Republic of China

Aiming to high repetition rate hard X-ray facility, con-struction of Shanghai HIgh repetition rate XFEL aNd Extreme light facility (SHINE) project has been ap-proved. During the R & D phase, prototypes fabrication of key components of 1.3GHz superconducting rf system have been proposed, especially 1.3 GHz 9-cell niobium cavities. Here the paper will present the progress of the fabrication status and performance of the prototypes, together with the analysis of not only the quality factor and gradient of the cavities. Consideration of HOM feed-throughs and absorbers are also reported.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP049

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP050

Modular Power Couplers for 217 MHz Superconducting CH-Cavities

Windows, linac, heavy-ion, simulation

168

J. List, K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, T. Kürzeder, S. Lauber, M. Miski-Oglu
HIM, Mainz, Germany
K. Aulenbacher, W.A. Barth, C. Burandt, V. Gettmann, M. Heilmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu, A. Schnase, S. Yaramyshev
GSI, Darmstadt, Germany
K. Aulenbacher, F.D. Dziuba, S. Lauber, J. List
IKP, Mainz, Germany
M. Basten, M. Busch, H. Podlech, M. Schwarz
IAP, Frankfurt am Main, Germany

The HELmholtz LInear ACcelerator (HELIAC) is being developed by a collaboration of HIM, GSI and the Goethe University of Frankfurt. It is a superconducting (sc), continuous wave (cw) heavy ion linac that comprises novel Crossbar H-mode (CH) cavities. In April 2017 and November/December 2018 the first sc CH-cavity of the linac was tested with beam. The first operations of the cavity showed, that the prototype of the rf power coupler needs to be further improved. A new version of the coupler is being designed at the HIM. Further development will mainly be focused on the heat input into the cryostat caused by the coupler. Also the coupler will have a modular design. This improves the accessibility and maintenance of the coupler. Various cryogenic and rf tests are foreseen, to provide a reliable, fail-safe coupler for the HELIAC. For an enhanced coupler test stand a movable reflector has been designed and built. With its movable semi-reflective element, it allows to operate the test stand in a resonance mode. In addition, the movable reflector can vary the coupling factor. This contribution discusses the recent coupler R&D for the HELIAC.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP050

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP051

3.9 GHz SRF Production Cavities for LCLS-II

cryomodule, linac, radiation, vacuum

173

S. Aderhold, A. Burrill
SLAC, Menlo Park, California, USA
D.J. Bice, C.M. Ginsburg, C.J. Grimm, T.N. Khabiboulline, O.S. Melnychuk, D.A. Sergatskov, N. Solyak, G. Wu
Fermilab, Batavia, Illinois, USA

Funding: This work was supported by the US DOE and the LCLS-II Project.
The main part of the SRF linac for the Linac Coherent Light Source II (LCLS-II) at SLAC will consist of 35 cryomodules with superconducting RF cavities operating at 1.3 GHz. In addition, two cryomodules with 3.9 GHz cavities will be installed and help to linearize the longitudinal phase space of the beam. During the design verification phase, four prototype 9-cell 3.9 GHz cavities had been built by industry and then processed, including chemical surface removal and heat treatment, and tested at Fermi National Accelerator Laboratory. Based on the resulting cavity treatment recipe, 24 cavities (for two cryomodules to be installed in the linac and one spare cryomodule) have been built by industry and tested at Fermilab prior to cryomodule string assembly. We present an overview of the cavity production and the results of the vertical acceptance tests for the LCLS-II 3.9 GHz cavities.

Poster MOP051 [1.015 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP051

About •

paper received ※ 02 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP054

Fabrication of 3.0-GHz Single-cell Cavities for Thin-film Study

SRF, MMI, FEL, linac

177

T. Saeki, H. Hayano, H. Inoue, R. Katayama, T. Kubo
KEK, Ibaraki, Japan
F.E. Hannon, R.A. Rimmer, A-M. Valente-Feliciano
JLab, Newport News, Virginia, USA
H. Ito
Sokendai, Ibaraki, Japan
Y. Iwashita, H. Tongu
Kyoto ICR, Uji, Kyoto, Japan

Funding: This work is supported by JSPS KAKENHI JP17H04839, JSPS KAKENHI JP26600142, Japan-US Research Collaboration Program, and the Collaborative Research Program of ICR Kyoto Univ. (2018-13).
We fabricated 3.0-GHz single-cell cavities with Cu and Nb materials for testing thin-film creations on the inner surface of the cavities in collaboration between Jefferson Laboratory (JLab) and KEK. The cavity was designed at JLab. According to the design of cavity, the press-forming dies and trimming fixtures for the cavity-cell were also designed and fabricated at JLab. These dies and trimming fixtures were transported to KEK, and the rest of fabrication processes were done at KEK. Finally nine Cu 3.0-GHz single-cell cavities and six Nb 3.0-GHz single-cell cavities were fabricated. Two Cu 3.0-GHz single-cell cavities were mechanically polished at Jlab. All of these cavities will be utilized for the tests of various thin-film creations at JLab and KEK. This presentation describes details of the fabrication of these cavities.

Poster MOP054 [1.203 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP054

About •

paper received ※ 05 July 2019 paper accepted ※ 13 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP055

Fabrication and Performance of Superconducting Quarter-Wavelength Resonators for SRILAC

linac, operation, cryomodule, acceleration

182

K. Suda, O. Kamigaito, K. Ozeki, N. Sakamoto, Y. Watanabe, K. Yamada
RIKEN Nishina Center, Wako, Japan
H. Hara, A. Miyamoto, K. Sennyu, T. Yanagisawa
MHI-MS, Kobe, Japan
E. Kako, H. Nakai, H. Sakai, K. Umemori
KEK, Ibaraki, Japan

A new superconducting booster linac (SRILAC) at the RIKEN heavy-ion linac is under construction. Ten 73-MHz low-beta quarter-wavelength resonators (QWRs) that operate at 4 K have been fabricated from pure niobium sheets. The cavity parts were assembled by electron beam welding. The resonant frequency for each cavity was adjusted by changing the lengths of the straight sections before welding. The performance and frequency were evaluated by vertical tests. All the cavities exceeded the design specifications of Q₀ = 1x10⁹ and E_acc = 6.8 MV/m. Details of the fabrication and frequency tuning as well as the performance of the cavities are reported.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP055

About •

paper received ※ 17 July 2019 paper accepted ※ 13 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP056

Surface Treatments for the Series Production of ESS Medium Beta Cavities

recirculation, SRF, niobium, simulation

188

M. Bertucci, A. Bosotti, A. D’Ambros, P. Michelato, L. Monaco, C. Pagani, R. Paparella, D. Sertore
INFN/LASA, Segrate (MI), Italy
C. Pagani
Università degli Studi di Milano & INFN, Segrate, Italy
D. Rizzetto, M. Rizzi
Ettore Zanon S.p.A., Schio, Italy
A. Visentin
Ettore Zanon S.p.A., Nuclear Division, Schio, Italy

The surface treatment of ESS 704 MHz medium beta cavities consists of a bulk BCP 200 micron removal, a 10 h 600°C heat treatment and a final 20 micron BCP performed after tank integration. The facility currently employed for the BCP treatment, settled in Ettore Zanon SpA, is here presented, together with the results so far obtained on the first series cavities in terms of frequency sensitivity, removal rate and surface external temperature. The optimization of BCP treatment by a preliminary fluid-dynamical finite element model is also discussed. Some details about the visual inspection procedure and the furnace qualification are also presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP056

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP057

Electropolishing of PIP-II Low Beta Cavity Prototypes

cathode, experiment, FEL, linac

194

M. Bertucci, A. Bosotti, A. D’Ambros, P. Michelato, L. Monaco, C. Pagani, R. Paparella, D. Sertore
INFN/LASA, Segrate (MI), Italy
A. Gresele, A. Visentin
Ettore Zanon S.p.A., Nuclear Division, Schio, Italy
C. Pagani
Università degli Studi di Milano & INFN, Segrate, Italy
D. Rizzetto, M. Rizzi
Ettore Zanon S.p.A., Schio, Italy

We present the upgrade of the EP facility for the surface treatment of PIP-II low beta cavities. The main process parameters, such as voltage, treatment time, acid throughput and cathode geometry, already optimized on the previous experience of 1.3 GHz Tesla-shape cavities, are discussed taking into account the different cavity size and geometry. The first surface treatments have been performed at Ettore Zanon SpA on single cell cavity prototypes in order to reach good final surface finishing and the required thickness removal. In the meantime, the upgrade of the system for the treatment of multicell PIP-II prototype cavities is presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP057

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP058

ESS Medium Beta Activity at INFN LASA

HOM, status, controls, SRF

199

D. Sertore, M. Bertucci, A. Bignami, A. Bosotti, M. Chiodini, A. D’Ambros, G. Fornasier, P. Michelato, L. Monaco, R. Paparella
INFN/LASA, Segrate (MI), Italy
S. Aurnia, O. Leonardi, A. Miraglia, G. Vecchio
INFN/LNS, Catania, Italy
A. Gresele, A. Visentin
Ettore Zanon S.p.A., Nuclear Division, Schio, Italy
C. Pagani
Università degli Studi di Milano & INFN, Segrate, Italy
D. Reschke, A. Sulimov, M. Wiencek
DESY, Hamburg, Germany
D. Rizzetto, M. Rizzi
Ettore Zanon S.p.A., Schio, Italy
L. Sagliano
ESS, Lund, Sweden

The industrial production of the 36 resonators (plus 2 spares) for the ESS linac started and it is steadily progressing. Cavities are delivered by industry as fully surface-treated and dressed to AMTF facility at DESY for their qualification via vertical cold-test. This paper reports the current status of the manufacturing process from sub-components to processing of the complete cavity inner surface. It also reviews the documental control strategy deployed to preserve the fulfillment of ESS requirements as well as the cavity performances demonstrated so far.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP058

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP060

INFN-LASA for the PIP-II Project

niobium, SRF, interface, linac

205

R. Paparella, M. Bertucci, A. Bignami, A. Bosotti, M. Chiodini, A. D’Ambros, P. Michelato, L. Monaco, D. Sertore
INFN/LASA, Segrate (MI), Italy
J.F. Chen
SARI-CAS, Pudong, Shanghai, People’s Republic of China
C. Pagani
Università degli Studi di Milano & INFN, Segrate, Italy
L. Sagliano
ESS, Lund, Sweden

INFN-LASA joined the international effort for the PIP-II project in Fermilab to build the 650 MHz superconducting cavities realizing the low-beta section of the 800 MeV proton linac. After developing the electro-magnetic and mechanical design, INFN-Milano started the prototyping phase by producing five single-cells and two complete 5-cells cavities. This paper reports the status of PIP-II activities at INFN-LASA summarizing manufacturing experience and preliminary experimental results.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP060

About •

paper received ※ 24 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP061

State of the Art of Niobium Machining for SRF Applications

niobium, SRF, electron, alignment

210

P. Naisson, S. Atieh, K. Scibor, P. Trubacova
CERN, Geneva, Switzerland
F. Dumont, D. Fabre, F. Valiorgue
ENISE, Saint Etienne, France

Niobium is a demanding material to be machined. Its low hardness, high melting temperature and abrasivity leads to poor cutting condition, and surface quality and shape accuracy could be difficult to achieve, especially for complex shapes such as HOM antennas. Recent CERN developements concerning DQW crab cavity for HL-LHC project had implied extensive research program to better understand and master the machining of this material. In this frame, the present article will introduce actual state of the art machining condition used at CERN and their consequences about the surface roughness, shape accuracy and taking into account the tool wear in order to maintain this level of quality. Morevoer, advance machning solution, such as cryogenic cooling could be used.

Poster MOP061 [2.921 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP061

About •

paper received ※ 30 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP062

Fabrication of SRF Cavity

coupling, vacuum, SRF, pick-up

214

K. Kanaoka, H. Hara, A. Miyamoto, K. Sennyu, T. Yanagisawa
MHI-MS, Kobe, Japan
E. Kako, K. Umemori
KEK, Ibaraki, Japan

Mitsubishi Heavy Industries Machinery Systems (MHI-MS) have developed manufacturing process of superconducting cavities for a long time. In this presentation, recent progress will be reported.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP062

About •

paper received ※ 23 June 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP063

Beam Loading in the BESSY VSR SRF Cavities

beam-loading, SRF, storage-ring, operation

217

A.V. Tsakanian, H.-W. Glock, J. Knobloch, A.V. Vélez
HZB, Berlin, Germany

The BESSY VSR upgrade of the BESSY II light source represents a novel approach to simultaneously store long (ca. 15 ps) and short (ca. 1.7 ps) bunches in the storage ring at currents up to 300 mA. This challenging goal requires installation of four new 4-cell SRF cavities (2x1.5 GHz and 2x1.75 GHz) in one module for installation in a single straight. As far as we are aware of, this is the first installation of multi-cell L-Band cavities in a high-current storage ring. These cavities are equipped with newly developed waveguide HOM dampers necessary for stable operation. Up to 2 kW of HOM power must be absorbed. Operating two SRF cavities for each frequency will also enable transparent parking of the cavities for the beam. Based on wakefield theory, a technique for beam loading calculation will be presented. The expected beam loading both at 2 K and at room temperature has been analyzed to evaluate transparent parking for both situations. The presented study is performed for various BESSY II and VSR bunch filling patterns with 300 mA beam current.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP063

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP064

Performance of First Prototype Multi-Cell Low-Surface-Field Shape Cavity

SRF, electron, niobium, experiment

222

R.L. Geng
JLab, Newport News, Virginia, USA
Y. Fuwa, Y. Iwashita
Kyoto ICR, Uji, Kyoto, Japan
H. Hayano
KEK, Ibaraki, Japan
H. Ito
Sokendai, Ibaraki, Japan
Z. Li
SLAC, Menlo Park, California, USA

The idea of cavity shaping for higher ultimate acceleration gradients has been proposed for some time, Low Loss/Ichiro and Re-entrant being examples, both seeking a lower Hpk/E_acc at the expense of a higher Epk/E_acc. While experimental verification in single-cell cavities of those shapes was very successful including the record gradient of 59 MV/m, pushing multi-cell cavities of those shapes to higher gradients was prevented by field emission. The Low-Surface-Field (LSF) shape seeks not only a lower Hpk/E_acc but also a lower Epk/E_acc, therefore it has the advantage of raising ultimate gradient at reduced field emission. The first multi-cell LSF shape prototype cavity was built using the standard forming and welding techniques. RF tests have been carried out, following standard ILC TDR baseline surface processing and treatment recipe. Three out of five cells achieved Hpk values corresponding to E_acc 50 MV/m. The current limit is the field emission in end cells. Instrumented testing following end-cell wiping and HPR with larger nozzles is in progress. We will present detailed experimental results and preparation procedures.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP064

About •

paper received ※ 24 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP065

Upgrade of the S-DALINAC Injector Capture Section

linac, MMI, gun, target

227

S. Weih, M. Arnold, J. Enders, N. Pietralla
TU Darmstadt, Darmstadt, Germany
D.B. Bazyl, H. De Gersem, W.F.O. Müller
TEMF, TU Darmstadt, Darmstadt, Germany

Funding: Work supported by DFG through GRK 2128 "AccelencE"
The superconducting injector section of the S-DALINAC (superconducting Darmstadt linear electron accelerator) [1] constists of two cryomodules with three 3-GHz SRF cavities in total. The first cavity of this pre-accelerator is currently a 5-cell structure designed for relativistic particle velocities. Since the gun delivers a 250 keV beam (β=0.74), this cavity is not suited for an efficient capture of the low-energy electron bunches provided by the normal-conducting section of the injector. Beam dynamics simulations and operational experience have shown a large low-energy tail in the phase-space distribution of the bunch downstream of the injector, which arises from the large phase-slippage during the capture in the 5-cell. It is therefore intended to replace the cavity with a beta-adapted 6-cell, re-using most of the cryostat parts. This contribution presents the status of the injector upgrade and the layout and manufacturing status of the new cavity.
*N. Pietralla, Nuclear Physics News, Vol. 28, No. 2, 4 (2018)

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP065

About •

paper received ※ 21 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP070

Investigation of the Critical RF Fields of Superconducting Cavity Connections

simulation, vacuum, niobium, impedance

230

J.C. Wolff, J.I. Iversen, D. Klinke, D. Kostin, D. Reschke, S. Sievers, A. Sulimov, J.H. Thie, M. Wiencek
DESY, Hamburg, Germany
R. Wendel, J.C. Wolff
HAW Hamburg, Hamburg, Germany

To optimise the length of the drift tube of a superconducting cavity (SC), it is required to know the critical value of the RF fields to prevent a potential early quench at the flange connection in case of a drift tube length reduction. To avoid changes on the SC which has been used for the tests, all RF cryogenic experiments have been carried out by using a cylinder in the center of a 1-cell cavity drift tube to increase the field magnitude at the connection. This cylinder has been designed and optimised by RF simulations to provide a field density at the connection twice as high as at a chosen reference point near the iris. Hence also a test SC with a comparatively low gradient can be used without causing field restrictions. In this contribution an approach to investigate the field limitations of 1.3 GHz TESLA-Shape SC connections and thereby the minimal drift tube length based on simulations will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP070

About •

paper received ※ 23 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP072

FRIB Solenoid Package in Cryomodule and Local Magnetic Shield

solenoid, cryomodule, operation, dipole

235

K. Saito, H. Ao, B. Bird, R. Bliton, N.K. Bultman, F. Casagrande, C. Compton, J. Curtin, K. Elliott, A. Ganshyn, W. Hartung, L. Hodges, K. Holland, S.H. Kim, S.M. Lidia, D. Luo, S.J. Miller, D.G. Morris, L. Nguyen, D. Norton, J.T. Popielarski, L. Popielarski, T. Russo, J.F. Schwartz, S.M. Shanab, M. Shuptar, D.R. Victory, C. Wei, J. Wei, M. Xu, T. Xu, Y. Yamazaki, C. Zhang, Q. Zhao
FRIB, East Lansing, Michigan, USA
A. Facco
INFN/LNL, Legnaro (PD), Italy
K. Hosoyama, M. Masuzawa
KEK, Ibaraki, Japan
R.E. Laxdal
TRIUMF, Vancouver, Canada

Funding: U.S. Department of Energy Office of Science under Cooperative Agreement DE -SC0000661
FRIB cryomodule design has a feature: solenoid package(s) and local magnetic shields in the cryomodule. In this design, exposing SRF cavities to a very strong fringe field from the solenoid is concerned. A tangled issue between solenoid package design and magnetic shield one has to be resolved. FRIB made intensive studies, designed, prototyped, validated the solenoid packages and magnetic shields, and finally certified them in the bunker test. This paper reports activity results, and LS1 commissioning results in FRIB tunnel. This is a FRIB success story.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP072

About •

paper received ※ 24 June 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP074

External Q Measurement for Quarter Wave Resonators in RISP

pick-up, cryomodule, simulation, coupling

245

S. Lee, B.H. Choi, M.O. Hyun, Y. Jung, J.W. Kim, Y. Kim, J. Lee, K.T. Seol
IBS, Daejeon, Republic of Korea

A heavy-ion accelerator facility is under construction for Rare Isotope Science Project(RISP) in Korea. The super conducting cavity, quarter wave resonator(QWR) which consists of driver and post linear accelerator system, is now in the mass production phase. In order to develop the QWR cavity and cryomodule, the RF couplers are fabriacated and tested. In this paper, the study of external Q for QWR coupler will be described.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP074

About •

paper received ※ 21 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP075

Design of RF Power Coupler Transmitting both 162.5 MHz and 81.25 MHz Power to SRF Cavities for BISOL R&D Research

ISOL, simulation, RF-structure, Windows

249

F. Zhu, M. Chen, A.Q. Cheng, J.K. Hao, S.W. Quan, F. Wang
PKU, Beijing, People’s Republic of China

Beijing isotope separation on line type rare ion beam facility (BISOL) is a proposed facility which has two superconducting RF linacs. One is a high intense driver linac which adopts half wave resonators (HWRs), and the other is the low current post-accelerator which includes quarter wave resonators (QWRs). For the pre-research of BISOL, a cryomodul which can do the horizontal test of both 81.25 MHz QWR for the post-accelerator and 162.5 MHz HWR for the driver accelerator with the proper external quality factor. For this purpose, Peking University are developing a coupler which can transfer 5 kW power to the 81.25 MHz QWR or cw 20 kW power to the 162.5 MHz HWR cavity. The electromagnetic optimization, Multipacting simulation, thermal analysis and detail structure of the coupler will be presented in this paper.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP075

About •

paper received ※ 21 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP076

Fundamental Power Coupler Design for a 325 MHz Balloon SSR Cavity

multipactoring, vacuum, simulation, cryogenics

252

R.E. Laxdal, Y. Ma, B. Matheson, B.S. Waraich, Z.Y. Yao, V. Zvyagintsev
TRIUMF, Vancouver, Canada

TRIUMF has designed, fabricated and tested the first balloon variant of the single spoke resonator at 325 MHz and β=0.3. TRIUMF has also designed a 6 kW fundamental power coupler as part of the development. The design of the coupler will be presented.

Poster MOP076 [1.282 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP076

About •

paper received ※ 24 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP078

Adjustable Power Coupler for NICA HWR Cavities

vacuum, simulation, coupling, collider

260

S.V. Matsievskiy, M.V. Lalayan
MEPhI, Moscow, Russia
D. Bychanok
INP BSU, Minsk, Belarus
M. Gusarova
JINR, Dubna, Moscow Region, Russia

Current results on input power coupler development for Half-Wave superconducting accelerating cavity proposed for Nuclotron-based Ion Collider fAcility (NICA) collider injector upgrade are discussed. Two coupler designs are considered, first one is a low-power coupler for cavity tests and the second one is a high-power operational coupler. Both devices are of coaxial type with capacitive coupling; high-power coupler utilizes single ceramic vacuum window. NICA is designed to accelerate different types of ions. Due to the variable intensity of ion sources, beam current will vary in wide range. In order to ensure efficient acceleration, power coupler must be highly adjustable in terms of coupling coefficient. This introduces excessive mechanical stress in the ceramic RF window due to the bellows deformation. In order to mitigate this effect bellows were substituted with sliding contacts. This paper discusses new coupler design and its electrical, mechanical and thermal properties.

Poster MOP078 [1.296 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP078

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP080

Latest Progress in Designs and Testings of PIP-II Power Couplers

rfq, vacuum, multipactoring, cryogenics

263

S. Kazakov, B.M. Hanna, O.V. Pronitchev, N. Solyak
Fermilab, Batavia, Illinois, USA

Proton Improvement Plan – II (PIP-II) project is under go in Fermi National Laboratory. Main part of the project is 800 MeV proton superconducting accelerator which includes 116 superconducting cavities of 5 different types and three 162.5, 325 and 650 MHz frequencies. Key elements of accelerator which determine a reliable operation are main couplers for superconducting cavities. This paper describes the latest progress in design and testing of main couplers for PIP-II projects.

Poster MOP080 [0.881 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP080

About •

paper received ※ 18 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP081

Considerations for Efficient RF Operation for the Advanced cw-Linac Demonstrator at GSI

linac, cryomodule, heavy-ion, SRF

267

C. Burandt, K. Aulenbacher, W.A. Barth, F.D. Dziuba, V. Gettmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu, S. Yaramyshev
HIM, Mainz, Germany
K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, M. Heilmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu, A. Schnase, S. Yaramyshev
GSI, Darmstadt, Germany
K. Aulenbacher, F.D. Dziuba, S. Lauber, J. List
IKP, Mainz, Germany
M. Basten, M. Busch, H. Podlech, M. Schwarz
IAP, Frankfurt am Main, Germany

The FAIR@GSI accelerator facility will require the GSI-UNILAC to provide short heavy ion pulses of highest intensity at low repetition rate for injection into the 18 Tm synchrotron SIS18. However, successful physics programs like SHE (Super Heavy Elements) rely on the UNILAC providing for heavy ion beams of high average current and high duty factor. In the next future, a dedicated super-conducting (sc) cw-Linac should therefore deliver cw beams to the experiments associated with those programs. As a first step towards this goal, beam tests with a single sc Cross-bar H-mode (CH) cavity were successfully conducted in 2017/2018. Within the scope of an Advanced Demonstrator project, current activities now aim at a beam test of a full cryomodule with three sc CH cavities and a sc rebuncher. Given a limited amount of rf power available per cavity and the necessity to accelerate different ion species with different mass-to-charge ratios, the loaded quality factor Q of the different resonators has to be chosen very carefully. This contribution discusses the simulations performed in this context.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP081

About •

paper received ※ 21 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP084

A Simple Variable Coupler for the Cryogenic Test of SRF Cavities

SRF, cryogenics, coupling, FEL

282

G. Ciovati, L. Turlington
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
The cryogenic rf tests of SRF cavities in vertical cryostats is typically carried out using fixed-length antennae to couple rf power into the cavity and to probe the energy stored into the cavity. Although variable couplers have been designed, built and used in the past, they are often a complex, costly, not very reliable auxiliary component to the cavity test. In this contribution we present the design and implementation of a simple variable rf antenna which has about 50 mm travel, allowing to obtain about four orders of magnitude variation in Q_ext -value. The motion of the antenna is driven by a motorized linear feedthrough outside of the cryostat. The antenna can easily be mounted on the most common type of cavity flanges.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP084

About •

paper received ※ 18 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP085

The Destructive Effects to the RF Coupler by the Plasma Discharge

plasma, experiment, vacuum, coupling

285

A.D. Wu, Q.W. Chu, H. Guo, Y. He, S.C. Huang, T.C. Jiang, C.L. Li, Z.Q. Lin, F. Pan, Y.K. Song, T. Tan, W.M. Yue, S.H. Zhang, H.W. Zhao
IMP/CAS, Lanzhou, People’s Republic of China

The low temperature RF plasma was proved an effec-tive method to clean the niobium surface and relieve the field emission effect for the SRF cavities. In the case of half-wave resonators, these cavities were usually powered via the fundamental coupler with the electric coupling. Thus, coupler antennas were fixed in the intense electric field region, and this region was where the plasma rou-tinely ignited. Therefore, the ceramic window of coupler taken the risk of breakdown under the sputtering of ions and heating loads that may be caused by the plasma drift and diffusion from the electric field region. In this paper, the plasma ignition for surface cleaning on the HWR cavity and its coupler was investigated, and the power transmission, temperature raising and vacuum degradation were tested to characterize the adverse impacts on the ceramic window. Finally, the solution was proposed to figure these issues.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP085

About •

paper received ※ 22 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP086

Conditioning of the First Mass Production Power Couplers for the ESS Elliptical Cavities

vacuum, electron, pick-up, Windows

288

C. Arcambal, M. Baudrier, P. Bosland, G. Devanz, T. Hamelin, C. Marchand, M. Oublaid, G. Perreu, S. Regnaud, C. Servouin, C. Simon
CEA-DRF-IRFU, France
G. Monnereau
CEA-IRFU, Gif-sur-Yvette, France

In the framework of the European Spallation Source (ESS), CEA Paris-Saclay is in charge of the delivery of 9 medium beta (β = 0.67) and 21 high beta (β = 0.86) cryomodules. Each cryomodule is composed of 4 cavities equipped with RF (Radio Frequency) power couplers (704.42 MHz, 1.1 MW maximum peak power, repetition rate=14 Hz, RF pulse width > 3.1 ms). Ten prototype power couplers have been manufactured to validate the design and the performance. Currently the mass production of the 120 couplers started and the six first pre-series medium beta couplers have been successfully conditioned. The achievement of this milestone allowed us to launch the production of the remaining 30 medium beta couplers. This paper presents the conditioning of the pre-series couplers.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP086

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP087

IFMIF Resonators Development and Performance

SRF, cryomodule, linac, solenoid

293

G. Devanz, M. Baudrier, P. Carbonnier, F. Éozénou, E. Fayette, D. Roudier, P. Sahuquet, C. Servouin
CEA-DRF-IRFU, France
N. Bazin, S. Chel, L. Maurice
CEA-IRFU, Gif-sur-Yvette, France

The prototype IFMIF cryomodule encloses eight superconducting 175 MHz beta 0.09 Half-Wave Resonators (HWR). They are designed together with the power coupler to accelerate a high intensity deuteron beam (125 mA) from to 5 to 9 MeV. One prototype HWR and the 8 cavities to be hosted in the cryomodule have been manufactured, prepared and tested. The paper describes the phases of the cavities development, including fabrication, processing, and RF resonant frequency management. We focus on the results of the RF tests which have been performed for all bare and jacketed HWRs in a vertical cryostat.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP087

About •

paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP089

Development of a Suspension System for the Road Transportation of Cryomodule SSR1 through a Multilevel Finite Element-Multibody Approach

ISOL, cryomodule, software, simulation

297

P. Neri, F. Bucchi
University of Pisa, Pisa, Italy
D. Passarelli
Fermilab, Batavia, Illinois, USA

The on-road transportation of cryomodules (CM) is a critical phase during which the structure may be subject to relevant dynamic loading. Thus, an accurate design of Transportation Tool (TT), equipped with a proper suspension system, is mandatory. In this paper the TT design for the PIP-II proto SSR1 CM is presented. A finite element (FE) model was developed considering the main CM parts. However, the full model was not suited for the design of the suspension system because of its computational time. Thus, it was exported as a Modal Neutral File to a multibody (MB) software, where minor components were modeled as rigid bodies or lumped stiffnesses. The reduced MB model considerably shortened the computational time and it was exploited for the design of the TT, which includes helical isolators (HI) acting as a mechanical filter. A real 3D acceleration profile, acquired during the transportation of a LCLS-II CM from Fermilab to SLAC, was used to validate the TT effectiveness in reducing the vibrational loading. In addition, the results of the MB analysis were used to perform FE analysis of critical components, such as bellows.

Poster MOP089 [0.995 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP089

About •

paper received ※ 29 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP092

Overview of LCLS-II Project Status at Fermilab

cryomodule, SRF, cryogenics, controls

302

R.P. Stanek, T.T. Arkan, J.N. Blowers, C.M. Ginsburg, A. Grassellino, C.J. Grimm, B.J. Hansen, E.R. Harms, B.D. Hartsell, J.P. Holzbauer, J.A. Kaluzny, A.L. Klebaner, A. Martinez, T.H. Nicol, Y.O. Orlov, K.S. Premo, N. Solyak, J. Theilacker, G. Wu
Fermilab, Batavia, Illinois, USA

The superconducting RF Continuous-Wave (CW) Linac for the LCLS-II consists of thirty-five 1.3 GHz and two 3.9 GHz cryomodules that Fermilab and Jefferson Lab are jointly producing in collaboration with SLAC. Fermilab¿s scope of work is to build, test, and deliver half the 1.3 GHz and all the 3.9 GHz cryomodules and to design and procure components for the cryogenic distribution system. Fermilab has primary responsibility for delivering a working design. The cryomodule design basis was the European XFEL but several elements evolved to meet CW operation requirements and specifics of the SLAC tunnel. There have been several challenges faced during the design, assembly, testing and transportation of the cryomodules which have required design updates. Success in overcoming these challenges is attributable to the strength of the LCLS-II SRF Collaboration (Fermilab, Jefferson Lab and SLAC with extensive help from DESY and CEA/Saclay). The cryogenic distribution system has progressed relatively well and there are valuable Lessons Learned. An overview of the status, accomplishments, problems encountered, solutions developed, and a summary of Lessons Learned will be presented.

Poster MOP092 [0.393 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP092

About •

paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP094

Design Strategy of the PIP-II Cryomodules

cryomodule, vacuum, interface, cryogenics

307

V. Roger, S.K. Chandrasekaran, D. Passarelli
Fermilab, Batavia, Illinois, USA

Funding: This manuscript has been authored by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the U.S. Department of Energy, Office of Science, Office of High Energy Physics
The Proton Improvement Plan II (PIP-II) is the first U.S. accelerator project that will have significant contributions from international partners. Research institutions in India, Italy, UK and France will build major components of the particle accelerator. The High Beta 650 MHz (HB650) prototype cryomodule is being designed jointly between Fermilab (USA), CEA (France), STFC (UK) and RRCAT (India). The assembly of this prototype cryomodule will be done at Fermilab whereas the production cryomodules will be assembled in UK. Concerning the Low Beta 650 MHz (LB650) cryomodules, they will be designed and assembled at CEA. To reduce the cost of the project and to increase the quality it is essential to define a design strategy for each cryomodule which includes a degree of standardization. In this way, the lessons learned of each prototype cryomodule will have a great impact not only on one cryomodule type but on all cryomodules. An international joint design brings also additional challenges to the project: which unit system should be used? Should a common project lifecycle management system be used for all partners? How to transport the cryomodules overseas.

Poster MOP094 [1.117 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP094

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP097

Preliminary Design of the IFMIF-DONES Superconducting Linac

cryomodule, linac, SRF, neutron

311

T. Plomion, N. Bazin, N. Chauvin, G. Devanz, J. Plouin, K. Romieu
CEA-DRF-IRFU, France
S. Chel
CEA-IRFU, Gif-sur-Yvette, France

The linear accelerator for the DONES facility (DEMO oriented neutron source) will serve as a neutron source for the assessment of materials damage in future fusion reactors. The DONES accelerator, which is based on the design of LIPac (Linear IFMIF Prototype Accelerator, which is under construction in Rokkasho, Japan) will accelerate deuterons from 100 keV up to 40 MeV at full CW current of 125 mA. This paper will present the preliminary design of the superconducting linac which is based on five cryomodules.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP097

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP098

Spoke Cryomodule Prototyping for the MINERVA Project

cryomodule, cryogenics, operation, controls

315

H. Saugnac, S. Blivet, N. Gandolfo, C. Joly, W. Kaabi, J. Lesrel, D. Longuevergne, G. Olivier, M. Pierens, W. Sarlin
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France
M.A. Baylac, D. Bondoux, F. Bouly, P.-O. Dumont, Y. Gómez Martínez
LPSC, Grenoble Cedex, France

In the framework of the MINERVA (MYRRHA 100 MeV) project, a prototyping period started at the end of 2017, has been planned. During this period a prototype cryomodule fully equipped (Spoke Cavities, Cryomodule Vessel, Cold Tuning System, Magnetic shielding, Power Couplers¿) as well as its operating and controlling components (LLRF, RF amplifiers¿) will be studied and manufactured. The aim of this prototyping period is first to complete the study of all the components and to validate the manufacturing and the assembling procedure in order to freeze the specifications for the serial construction. On the other hand the prototypes will serve as a test stand allowing to study and adjust the "Fault Tolerance" strategy parameters , which is a challenging operating concept specific to the MYRRHA LINAC This poster presents the various tasks related to this Spoke Cryomodule prototyping and their status.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP098

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP099

Design of Crab Cavity Cryomodule for HL-LHC

cryomodule, vacuum, cryogenics, operation

320

T. Capelli, K. Artoos, A.B. Boucherie, K. Brodzinski, R. Calaga, S.J. Calvo, E. Cano-Pleite, O. Capatina, F. Carra, L. Dassa, F. Eriksson, M. Garlasché, A. Krawczyk, R. Leuxe, P. Minginette, E. Montesinos, B. Prochal, M. Sosin, M. Therasse
CERN, Geneva, Switzerland
T.J. Jones, N. Templeton
STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom
A. Krawczyk, B. Prochal
IFJ-PAN, Kraków, Poland
S.M. Pattalwar
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom

Funding: Research supported by the HL-LHC project
Crab cavities are a key element to achieve the HL-LHC performance goals. There are two types of cavities Double Quarter Wave (DQW) for vertical crabbing, and Radiofrequency Dipole (RFD) for horizontal crabbing. Cavities are hosted in a cryomodule to provide optimal conditions for their operation at 2K while minimizing the external thermal loads and stray magnetic fields. One crab cryomodule contains more than thirteen thousand components and the assembly procedure for the first DQW prototype was carefully planned and executed. It was installed in the SPS accelerator at CERN in 2018 and successfully tested with proton beams. A review has thus been performed right after completion of the assembly in order to gather all the experience acquired and improve accordingly the design of the next generation of crab cryomodules. A second cryomodule with two RFD cavities is currently under production. This paper presents the lessons learnt from the first assembly and their implementation to the design of the future crab cryomodules.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP099

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP100

Design Upgrades of the Next Superconducting RF Gun for ELBE

gun, SRF, cathode, cryomodule

326

J. Teichert, A. Arnold, S. Ma, P. Murcek, J. Schaber, H. Vennekate, R. Xiang, P.Z. Zwartek
HZDR, Dresden, Germany
K. Zhou
CAEP/IAE, Mianyang, Sichuan, People’s Republic of China

Funding: Funding is provided by the China Scholarship Council.
At the ELBE user facility a superconducting RF photoinjector has been in operation since several years. The injector is routinely applied for THz radiation production in user beam experiments. For future applications higher bunch charges, shorter pulses and lower transverse emittances are required. Thus it is planned to replace this SRF gun by a next version with an RF cavity reaching a higher acceleration gradient. We also present improvements concerning the SC solenoid and the photocathode exchange system and report on the status of construction and testing of this SRF gun cryomodule.

Poster MOP100 [2.199 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP100

About •

paper received ※ 27 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOP105

A Superconducting Magnetic Shield for the Photoelectron Injector of BERLinPro

solenoid, gun, shielding, operation

335

J. Völker, A. Frahm, A. Jankowiak, S. Keckert, J. Knobloch, G. Kourkafas, O. Kugeler, A. Neumann, H. Plötz
HZB, Berlin, Germany

Magnetic fields are a big issue for SRF cavities, especially in areas with strong electromagnets or ferromagnetic materials. Magnetic shieldings consisting of metal alloys with high magnetic permeability are often used to reroute the external magnetic flux from the cavity region. Those Mu metal shields are typically designed for weak magnetic fields like Earth’s magnetic field. Next to strong magnetic field sources like superconducting (SC) solenoids, those shields can be easily saturated resulting in a degradation of the shielding efficiency and a permanent magnetization. For the photoinjector of BERLinPro a new SC solenoid will be installed inside the cryomodule next to the SRF gun cavity. Calculations show that the fringe fields of the solenoid during operation can saturate the cavity Mu-metal shields. Therefore we designed an SC magnetic shield placed between solenoid and cavity shield to protect the latter during magnet operation. In this paper we will present the design and first measurements of this SC magnetic shield.

Poster MOP105 [2.011 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-MOP105

About •

paper received ※ 04 July 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUA1

The Field-Dependent Surface Resistance of Doped Niobium: New Experimental and Theoretical Results

SRF, niobium, electron, ECR

340

J.T. Maniscalco, M. Ge, P.N. Koufalis, M. Liepe
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
T. Arias, D. Liarte, J.P. Sethna, N. Sitaraman
Cornell University, Ithaca, New York, USA

We present systematic work investigating how different doping and post-doping treatments affect the BCS surface resistance at 1.3~GHz and higher frequencies. We examine the field-dependent BCS resistance at many temperatures as well as the field-dependent residual resistance and use the results to reveal how impurity species and concentration levels affect the field-dependent RF properties. We further demonstrate the importance of thermal effects and their direct dependence on doping level. We use the tools of Density Functional Theory to work towards an {\em ab initio} model of electron overheating to theoretically confirm the impact of doping, create a full model that includes thermal effects to predict the field dependent resistance, and show that the predictions of the model agree with results from doped and non-doped cavities ({\em e.g.} the strength of the anti-Q-slope and the high-field Q slope). Finally, we use our experimental results to systematically assess and compare theories of the field-dependent BCS resistance, showing that the current theory on smearing of the density of states is incomplete.

Slides TUFUA1 [6.780 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUFUA1

About •

paper received ※ 01 July 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUA4

New Insights on Nitrogen Doping

electron, SRF, ECR, niobium

347

D. Bafia, J. Zasadzinski
IIT, Chicago, Illinois, USA
D. Bafia, M. Checchin, A. Grassellino, O.S. Melnychuk, A.S. Romanenko, D.A. Sergatskov
Fermilab, Batavia, Illinois, USA

This paper covers a systematic study of the quench in nitrogen doped cavities: a cavity was sequentially treated/reset with different N-doping recipes which are known to produce different levels of quench field. Analysis of cavity heating profiles using TMAP are used to gain insight on the origins of quench; new recipes demonstrate the possibility to increase quench fields well beyond 30 MV/m. In addition, a new signature of nitrogen doping is explored, namely, a dip in the superconducting resonant frequency below the normal conducting value just below the critical transition temperature, giving further insights on the mechanisms responsible for the large increase in performance of cavities subject to this surface treatment.

Slides TUFUA4 [3.097 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUFUA4

About •

paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUA5

Recent Development on Nitrogen Infusion Work Towards High Q and High Gradient

SRF, niobium, injection, radio-frequency

355

P. Dhakal
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
A quality factor as high as 2 × 10¹⁰ at 1.5 GHz was achieved at a gradient of 35 MV/m by 800 °C annealing and N-infusion at 140 °C. A comparison of the field dependence of the surface resistance after N-infusion with a recent theoretical model that extends the calculation of the BCS surface resistance to high rf fields suggests an increase in the quasiparticles¿ relaxation time with increasing infusion temperature, which could be due to a decreasing density of subgap states. Nb coupons treated similarly showed the formation of thicker oxynitride layer on the surface beneath thin dielectric Nb₂O₅ layer. A plausible explanation for the improved Q₀ is that the oxynitride layer on the Nb surface adds additional electron scattering within RF penetration depth.

Slides TUFUA5 [6.077 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUFUA5

About •

paper received ※ 19 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUA7

Review of Muon Spin Rotation Studies of SRF Materials

SRF, niobium, experiment, FEL

360

T. Junginger
Lancaster University, Lancaster, United Kingdom
R.E. Laxdal
TRIUMF, Vancouver, Canada

Muons spin rotate in magnetic fields and emit a positron preferentially in spin direction after decay. These properties enable muon spin rotation (muSR) as a precise probe for local magnetism. muSR has been used to characterize SRF materials since 2010. At TRIUMF a so called surface beam implants muons at a material dependent depth of about 150 µm in the bulk. A dedicated spectrometer was developed for field of first vortex penetration and pinning strength measurements of SRF materials in parallel magnetic fields of up to 300 mT. A low energy beam available at PSI implants muons at variable depth in the London layer allowing for direct measurements of the London penetration depth from which the lower critical field and the superheating field can be calculated. This facility is limited to parallel magnetic fields of up to 25 mT. Here, surface and low energy muSR results on SRF materials are reviewed and cross-correlated to each other and to further results from additional experiments. Finally, we present the status of a new facility based on the similar beta-NMR technique enabling measurements in the London layer of SRF materials exposed to parallel magnetic fields above 200 mT.

Slides TUFUA7 [4.063 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUFUA7

About •

paper received ※ 01 July 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUB3

Mapping Flux Trapping in SRF Cavities to Analyze the Impact of Geometry

experiment, HOM, niobium, simulation

364

F. Kramer, J. Knobloch, O. Kugeler, J.M. Köszegi
HZB, Berlin, Germany
J. Knobloch
University of Siegen, Siegen, Germany

A combined temperature and magnetic field mapping system was used to investigate the impact of an ambient field on trapped flux and on the resulting local surface resistance. For this, a 1.3 GHz TESLA single cell cavity was cooled through the superconducting transition at different magnetic field angles with respect to the cavity axis. The measurements suggest, that the field is trapped homogeneously over the cavity volume, without changing its orientation. Flux trapped perpendicular the surface contributed significantly more to the surface resistance, than trapped flux parallel to the surface.

Slides TUFUB3 [12.777 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUFUB3

About •

paper received ※ 21 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUB5

Effects of Static Magnetic Fields on a Low-frequency TEM Class Superconducting Cavity

niobium, shielding, SRF, superconductivity

370

M.K. Ng, Z.A. Conway, M.P. Kelly, K.W. Shepard
ANL, Lemont, Illinois, USA

Systematic studies on the effect of magnetic fields on a 330 MHz superconducting (TEM-mode) half-wave cavity are presented. The practical application of the results is for a possible future 2 K operation in the ATLAS heavy-ion accelerator at Argonne. The low frequency and the integral stainless steel jacket, rather than titanium, provide important new data for this full production model low-beta cavity. The studies include multi-axial magnetic field measurements near the cavity surface due to ambient and applied fields. Cavity performance under different conditions is measured at temperatures ranging between 1.6 K and 4.5 K. A residual resistance of approximately 5-7 nΩ at 1.6 K is observed. Data suggest that an appreciable fraction arises from losses that are not due to flux trapping.

Slides TUFUB5 [1.195 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUFUB5

About •

paper received ※ 24 June 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUB7

Measurement of Surface Resistance Properties with Coaxial Resonators - Review

multipactoring, experiment, ECR, SRF

374

H. Park, S.U. De Silva, J.R. Delayen
ODU, Norfolk, Virginia, USA

Achieving ever decreasing surface resistance at higher field in superconducting RF accelerating structures is one of most outstanding developments in modern accelerators. The BCS theory has been used widely to estimate the surface resistance and to direct the technology. However, recent research results show that the behavior of the surface resistance further deviates from the BCS theory. So far the study on surface resistance was performed usually with cavities of single frequency which limited the study of frequency dependent surface resistance. The Center for Accelerator Science at Old Dominion University has designed and built several half wave coaxial cavities to study the frequency, temperature, and RF field dependence of surface resistance. TRIUMF in Canada also joined this line of research using such multi frequency quarter wave and half wave coaxial cavities. This type of multi mode cavity will allow us to systematically study the parameters affecting surface resistance on the same cavity surface. In this paper, we review the results ODU and TRIUMF collected so far and proper analysis methods.

Slides TUFUB7 [3.551 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUFUB7

About •

paper received ※ 01 July 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUFUB8

CVD Coated Copper Substrate SRF Cavity Research at Cornell University

SRF, niobium, interface, target

381

M. Ge, T. Gruber, J.J. Kaufman, M. Liepe, J.T. Maniscalco, T.E. Oseroff, R.D. Porter, Z. Sun
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
V.M. Arrieta, S.R. McNeal
Ultramet, Pacoima, California, USA

Chemical vapor deposition (CVD) is a promising alternative to conventional sputter techniques for coating copper substrate cavities with high-quality superconducting films. Through multiple SRF-related DOE SBIR projects, Ultramet has developed CVD processes and CVD reactor designs for SRF cavities, and Cornell University has conducted extensive RF testing of CVD coated surfaces. Here we report results from thin-film CVD Nb₃Sn coated copper test plates, and for thick-film CVD niobium on copper including full-scale single cell 1.3 GHz copper substrate cavities. Detailed optical inspection and surface characterization show high-quality and well-adhered coatings. No copper contamination is found. The Nb₃Sn coated plates have a uniform Nb₃Sn coating with a slightly low tin concentration (19 -22%), but a BCS resistance well in agreement with predictions. The CVD Nb coatings on copper plates demonstrate excellent adhesion characteristics and exceeded surface fields of 50 mT without showing signs of a strong Q-slope that is frequently observed in sputtered Nb cavities. Multiple single-cell 1.3 GHz copper cavities have been coated to date at Ultramet, and results from RF testing of these are presented and discussed.

Slides TUFUB8 [12.488 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUFUB8

About •

paper received ※ 01 July 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP002

Modeling of Superconducting Spoke Cavity with its Control Loops Systems for the MYRRHA Linac Project

linac, LLRF, cryomodule, feedback

387

M. Dominiczak
ACS, Orsay, France
F. Bouly
LPSC, Grenoble Cedex, France
N. Gandolfo, C. Joly
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France

In the construction framework of a future 600 MeV/4 mA CW Superconducting Linac accelerator for the MYRRHA project at SCK•CEN (Mol, Belgium), modeling works under Matlab/Simulink are carried out upstream to understand the behaviour of 352 MHz single Spoke cavity with its environment and its associated feedback control loops (LLRF and cold tuning system). One of the main goal is to assess the feasibility of cavity failure compensation in the Superconducting Linac. Indeed, stringent reliability requirements must be fulfilled to ensure an efficient operation of the MYRRHA Accelerator Driven System: unexpected beam interruptions, due to failures, must be compensated in less than 3 seconds. Our preliminary study focuses on the fast frequency re-tuning of the cavity and the power balances. Our goal is to prepare the R&D tests foreseen at IPN Orsay on a prototype cryomodule including two SC Spoke cavities equipped with couplers, tuners with feedback loop and connected to dedicate LLRF.
Nicolas Gandolfo, IPNO, Orsay (France)
Christophe Joly, IPNO, Orsay (France)
Frédéric Bouly, LPSC, Grenoble (France)

Poster TUP002 [1.335 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP002

About •

paper received ※ 23 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP004

Latest Cryogenic Test Results of the Superconducting β=0.069 CH-cavities for the HELIAC-project

linac, vacuum, cryomodule, heavy-ion

392

M. Basten, M. Busch, T. Conrad, H. Podlech, M. Schwarz
IAP, Frankfurt am Main, Germany
K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, M. Heilmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu, J. Salvatore, A. Schnase, S. Yaramyshev
GSI, Darmstadt, Germany
K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu
HIM, Mainz, Germany
K. Aulenbacher, S. Lauber
IKP, Mainz, Germany
F.D. Dziuba, J. List
KPH, Mainz, Germany

The upcoming FAIR (Facility for Antiproton and Ion Research) project at GSI will use the existing UNILAC (UNIversal Linear Accelerator) as an injector, reducing the beam time for the ambitious Super Heavy Element (SHE) program. To keep the UNILAC user program competitive a new superconducting (sc) continuous wave (cw) high intensity heavy ion LINAC should provide ion beams with max. duty factor above the coulomb barrier. The fundamental sc LINAC design comprises a low energy beam transport (LEBT)-section followed by a sc Drift Tube Linac (DTL) consisting of sc Crossbar-H-mode (CH) structures for acceleration up to 7.3 MeV/u. The latest milestones towards the new cw LINAC HELIAC (HELmholtz LInear ACcelerator) have been the successful tests and commissioning of the first demonstrator section with heavy ion beam in 2017 and 218 as well as the successful test under cryogenic conditions of the second CH-cavity in 2018. Now the third CH-cavity has been tested at cryogenic temperatures of 4 Kelvin at the Institute for Applied Physics (IAP) at Goethe University Frankfurt (GUF). The results of these measurements as well as the status of the HELIAC-project will be presented.

Poster TUP004 [0.958 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP004

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP005

Cavity Designs for the CH3 to CH11 of the Superconducting Heavy Ion Accelerator HELIAC

linac, heavy-ion, resonance, electron

396

T. Conrad, M. Basten, M. Busch, H. Podlech, M. Schwarz
IAP, Frankfurt am Main, Germany
K. Aulenbacher, W.A. Barth, F.D. Dziuba, V. Gettmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu
HIM, Mainz, Germany
K. Aulenbacher
KPH, Mainz, Germany
W.A. Barth, M. Heilmann, A. Rubin, A. Schnase, S. Yaramyshev
GSI, Darmstadt, Germany

In collaboration of GSI, HIM and Goethe University Frankfurt new designs for the CH-DTL cavities of the proposed Helmholtz Linear Accelerator (HELIAC) are developed. The cw-mode operated linac with a final energy of 7.3 MeV/u is intended for various experiments, especially with heavy ions at energies near the coulomb barrier. Currently twelve superconducting CH-cavities are considered which will be split into four different cryostats. Each cavity will be equipped with dynamic bellow tuners. After successful beam tests with CH⁰ as well as last surface preparations and ongoing rf tests with CH1 and CH2, CH3 to CH11 will be designed. Based on the successful test results, individual optimizations are carried out on the cavity design. Attention was paid to reduce production costs, for example by keeping the cavity diameter in each cryostat constant despite varying particle velocities and gap numbers. In addition to reaching the resonance frequency of 216.816 MHz and the influence of the bellow tuners on the frequency, the mechanical stability of the bellow tuners, the thermal effects on the cavity and the measures to mitigate secondary electron emission are investigated.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP005

About •

paper received ※ 19 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP007

Electromagnetic Design of the Prototype Spoke Cavity for the JAEA-ADS Linac

linac, SRF, proton, superconductivity

399

J. Tamura, K. Hasegawa, Y. Kondo, F.M. Maekawa, S.I. Meigo, B. Yee-Rendón
JAEA/J-PARC, Tokai-mura, Japan
E. Kako, T. Konomi, H. Sakai, K. Umemori
KEK, Ibaraki, Japan

The Japan Atomic Energy Agency (JAEA) is proposing an accelerator-driven subcritical system (ADS) as a future project to transmute long-lived nuclides to short-lived or stable ones. In the JAEA-ADS, a high-power proton beam of 30 MW with a final beam energy of 1.5 GeV is required with a high reliability. Furthermore, the accelerator needs to be operated in a continuous wave mode in order to be compatible with the reactor operation. As the first step toward the detailed design of the JAEA-ADS linac, we are planning to demonstrate a high-field measurement by prototyping a low-beta single spoke resonator (SSR1). We performed the electromagnetic design, and confirmed that the cavity performances of the SSR1 model with and without dimensional constraint.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP007

About •

paper received ※ 02 July 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP008

HOMs Extraction Structure Design for HEPS 166.6 MHz Cavities

HOM, extraction, experiment, simulation

403

X.R. Hao
IHEP, Beijing, People’s Republic of China

Higher order modes (HOMs) may af{}fect beam stability and refrigeration requirements of superconducting cavity such as the 166.6~MHz superconducting(SC) cavity, which is studied at IHEP. Under certain conditions beam-induced HOMs can accumulate suf{}f{}icient energy to destabilize the beam or quench the SC cavities. In order to limit these ef{}fects, we considers the use of coaxial HOM couplers on the cut-of{}f tubes of the SC cavity. However, HOMs cannot be ef{}fectively extracted by HOM couplers. Therefore, it is necessary to design a HOMs extraction structure to introduce the dangerous modes from the cavity into the bundle tube, which are designed to couple to potentially dangerous modes while suf{}ficiently rejecting the fundamental mode. The HOMs extraction structure consists of an enlarged tubes, a coaxial structure, and the petal. The extraction of the dangerous modes and the suppression of the fundamental mode are realized by the petal structure and the coaxial structure. In order to verify the designs, a rapid prototype for the favored structure was fabricated and characterized on a low-power test-stand.

Poster TUP008 [1.665 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP008

About •

paper received ※ 22 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP010

Mechanical Design and Horizontal Tests of a Dressed 166.6 MHz Quarter-wave β=1 SRF Cavity System

simulation, cryomodule, superconducting-cavity, SRF

408

X.Y. Zhang, X.R. Hao, D.B. Li, Z.Q. Li, H.Y. Lin, Q. Ma, Z.H. Mi, Q.Y. Wang, P. Zhang
IHEP, Beijing, People’s Republic of China

Funding: This work has been supported by HEPS-TF project.
A 166.6 MHz quarter-wave β=1 superconducting proof-of-principle cavity has been designed and recently been dressed with a helium jacket, fundamental power coupler and tuner. The cavity was subsequently installed in a modified cryomodule and tested in a horizontal manner at both 4.2 K and 2 K. The helium jacket was successfully developed with a focus on minimizing frequency shift due to helium pressure fluctuation while retaining a reasonable tuning range. The Lorentz force detuning (LFD) and microphonics were also optimized during the design. The df/dp and LFD coefficient were measured to be -3.1 Hz/mbar and -0.8 Hz/(MV/m)². These are in good agreement with simulations. Future work is mainly to reduce the stiffness of the cavity and further suppress the vibration mode of the inner conductor.

Poster TUP010 [1.245 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP010

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP011

QWR085 Design for Bisol Post Accelerator SCL2

ISOL, simulation, LEBT, niobium

413

M. Chen, S. Chen, A.Q. Cheng, J.K. Hao, K.X. Liu, Y.Q. Liu, D.M. Ouyang, S.W. Quan, F. Zhu
PKU, Beijing, People’s Republic of China
Z. Peng
CIAE, Beijing, People’s Republic of China

BISOL(Beijing Isotope-Separation-On-Line Neutron-Rich Beam Facility) is a new generation radioactive ion beam(RIB) facility[1]. It consists a CARR nuclear reactor, a high intensity deuteron accelerator and a post accelera-tor. QWR085 cavity is supposed to be used in SCL2 of post accelerator. This paper mainly talks about the elec-tromagnetic design, mechanical design and vibration damper design of QWR085.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP011

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP012

Evaluation of High Performance Large Grain Medium Purity SRF Cavity From KEK

niobium, SRF, experiment, cryogenics

415

P. Dhakal, G. Ciovati, G.R. Myneni
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
We presented the RF measurement on a 1.3 GHz single cell cavity fabricated at KEK using large grain ingot niobium with RRR=10⁷. The cavity reached to 35 MV/m with Q₀ = 2.0×10^zEhNZeHn at 2.0 K, record performance on the cavity made from medium purity ingot niobium. The cavity was cool down with different temperature gradient along the cavity axis in order to understand the flux expulsion mechanism when the cavity does through the superconducting transition and effect of trap residual magnetic field on the residual resistance. The measurement showed the excellent flux expulsion with the flux trapping sensitivity of 0.29 nΩ/mG for electro polished surface and 0.44 nΩ/mG for cavity followed by low temperature baking at 120°C for 12 hours.
We acknowledge KEK for sending this cavity for evaluations.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP012

About •

paper received ※ 17 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP013

Non-Evaporative Getter-Based Differential Pumping System for SRILAC at RIBF

vacuum, SRF, linac, operation

419

H. Imao
RIKEN Nishina Center for Accelerator-Based Science, Wako, Saitama, Japan
O. Kamigaito, N. Sakamoto, T. Watanabe, Y. Watanabe, K. Yamada
RIKEN Nishina Center, Wako, Japan
K. Oyamada
SHI Accelerator Service Ltd., Tokyo, Japan

Upgrades of the RIKEN heavy-ion linac (RILAC) involving a new superconducting linac (SRILAC) are undergoing to promote super-heavy element searches at the RIKEN radioactive isotope beam factory (RIBF). Stable ultra-high vacuum (<10^-8 Pa) and particulate-free conditions are strictly necessary for keeping the performance of the superconductive radio frequency (SRF) cavities of the SRILAC. It is crucially important to develop neighboring warm sections to prevent contamination from the existing old RILAC and beamlines built almost four decades ago. In the present study, non-evaporative getter-based differential pumping systems were newly developed to achieve the pressure reduction from the existing beamline vacuum (10^-5–10^-6 Pa ) to the ultra-high vacuum within very limited length (<80 cm) ensuring the large beam aperture of more than 40 mm. They are also equipped with compact electrostatic particle removers. We will describe and discuss details of the design, construction and performance of the system.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP013

About •

paper received ※ 03 July 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP014

Mechanical Design and Fabrication Aspects of Prototype SSR2 Jacketed Cavities

SRF, interface, cryomodule, electron

424

M. Parise, D. Passarelli, F. Ruiu
Fermilab, Batavia, Illinois, USA
P. Duchesne, D. Longuevergne, D. Reynet
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France

A total of 35 Superconducting SSR2 spoke cavities will be installed in the PIP II SRF linac at Fermilab and a total of 8 prototype SSR2 cavities will be manufactured for the prototype cryomodule. In this paper, the mechanical design and fabrication aspects of the prototype jacketed SSR2 cavity will be presented. RF and mechanical design activities were conducted in parallel directly on the jacketed cavity in order to minimize the number of design iterations. Also, the lessons learned from other spoke cavities experiences (i.e. SSR1 at Fermilab and ESS double spoke at IPNO) were considered since the early stage of the design.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP014

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP016

Quarter-wave Resonator with the Optimized Shape for Quantum Information Systems

niobium, photon, shielding, factory

430

S.V. Kutsaev, R.B. Agustsson, P.R. Carriere, A. Moro, A.Yu. Smirnov, K.V. Taletski
RadiaBeam, Santa Monica, California, USA
A.N. Cleland, É. Dumur
The University of Chicago, Chicago, Illinois, USA
Z.A. Conway
ANL, Lemont, Illinois, USA
K.V. Taletski
MEPhI, Moscow, Russia

Funding: This work was supported by the U.S. Department of Energy, Office of High Energy Physics, under SBIR grant DE-SC0018753
Quantum computers (QC), if realized, could disrupt many computationally intense fields of science. The building block element of a QC is a quantum bit (qubit). Qubits enable the use of quantum superposition and multi-state entanglement in QC calculations, allowing a QC to simultaneously calculate millions of computations at once. However, quantum states stored in a qubit degrade with decreased quality factors and interactions with the environment. One technical solution to improve qubit lifetimes and network interactions is a circuit comprised of a Josephson junction located inside of a high Q-factor superconducting 3D cavity. RadiaBeam, in collaboration with Argonne National Laboratory and The University of Chicago, has developed a superconducting radio-frequency quarter-wave resonant cavity (QWR) for quantum computation. Here a 6 GHz QWR was optimized to include tapering of the inner and outer conductors, a toroidal shape for the resonator shorting plane, and the inner conductor to reduce parasitic capacitance. In this paper, we present the results of the qubit cavity design optimization, fabrication, processing and testing in a single-photon regime at mK temperatures.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP016

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP018

New SRF Structures Processed at the ANL Cavity Processing Facility

cathode, SRF, niobium, dipole

434

T. Reid, Z.A. Conway, B.M. Guilfoyle, M. Kedzie, M.P. Kelly, M.K. Ng
ANL, Lemont, Illinois, USA

Argonne National Laboratory (ANL) has extended high quality cavity processing techniques based on those developed for the International Linear Collider to several more complex superconducting RF cavities. Recently, these include a bunch lengthening harmonic cavity, a crabbing rf-dipole cavity, a compact half-wave cavity, and both medium and high frequency elliptical cavities. These systems are an improved version of the one originally developed for 1.3 GHz 9-cell cavities and include a second rotating electrical contact that can support multiple cathodes, necessary for optimum polishing in difficult cavity geometries. All include the possibility for external water cooling.

Poster TUP018 [4.322 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP018

About •

paper received ※ 28 June 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP019

Status of High Temperature Vacuum Heat Treatment Program at IPN Orsay

SRF, niobium, MMI, vacuum

438

M. Fouaidy, F. Chatelet, V. Delpech, F. Galet, D. Le Dréan, R. Martret, G. Olry, T. Pépin-Donat
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France
M. Baudrier, P. Carbonnier, E. Fayette, X. Hanus, Th. Proslier, D. Roudier, P. Sahuquet, C. Servouin
CEA-DRF-IRFU, France
E. Cenni, L. Maurice
CEA-IRFU, Gif-sur-Yvette, France
D. Longuevergne
FLUO, Orsay, France

In the framework of ESS, a vacuum furnace dedicated to High Temperature Heat Treatment under Vacuum (VH2T2) of SRF bulk Nb cavities was developed and commissioned in May 2016. This furnace is currently used for interstitial hydrogen removal (10h00 @ 650 °C) of two type of cavities: 1) the whole series of 26 ESS 352 MHz spoke resonators equipped with their Ti LHe tank well, 2) some prototypes of ESS high beta and medium beta cavities. Up to know IPN Orsay VH2T2 (10h00 @ 650 °C) was successfully applied to more than 16 cavities. In this paper we will first report about these VH2T2 tests. Finally, we have just started testing nitrogen infusion and nitrogen doping processes on samples and 1.3 GHz cavities: the preliminary results will be discussed.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP019

About •

paper received ※ 03 July 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP020

Statistical Analysis of the 120°C Bake Procedure of Superconducting Radio Frequency Cavities

accelerating-gradient, FEL, SRF, niobium

444

L. Steder, D. Reschke
DESY, Hamburg, Germany

DESY is and was very active in R&D related to SRF cavities. Many single and nine cell cavities with different surface treatment histories were tested vertically. Results of these cold tests are accelerating gradient and quality factor of the cavities. Using the large number of available datasets the parameters of the 120°C bake procedure, which is applied to avoid high-field Q-slope, are analysed. The impact of different durations and temperatures on accelerating gradient, quality factor and residual resistance is studied in detail and is compared to results obtained with the recently proposed procedure of modified low temperature bake. For this procedure additional four hours at temperatures around 75°C are implemented before the standard bake at about 120°C. Since the claim is, that cavities treated with such a modified procedure achieve extra-ordinary large accelerating gradients it is a very interesting research field for the European XFEL continuous wave mode upgrade. For this purpose cavities with high quality factors are needed, but in addition large maximal accelerating fields are required to maintain high energies in the pulsed operation mode of the accelerator.

Poster TUP020 [0.747 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP020

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP021

Effect of Cathode Rotation and Acid Flow in Vertical Electropolishing of 1.3 GHz Niobium Nine-Cell Cavity

cathode, experiment, SRF, niobium

448

V. Chouhan, Y.I. Ida, K.N. Nii, T.Y. Yamaguchi
MGH, Hyogo-ken, Japan
H. Hayano, S. Kato, H. Monjushiro, T. Saeki
KEK, Ibaraki, Japan

We have been carrying out R&D on vertical electropolishing (VEP) technique to establish it as an alternate of the horizontal EP (HEP) technique used for the surface treatment of niobium (Nb) superconducting RF (SRF) cavities. We have earlier reported on a VEP parameter study for 1.3 GHz single and nine-cell Nb cavities. The optimized VEP parameters and a unique rotating cathode yielded uniform removal and a smooth surface in the single cell cavity. The unique cathode and a dual flow mechanism for acid circulation were applied to improve the removal uniformity in the nine-cell cavity. The vertically electropolished single and nine cell cavities achieved the same RF performance as achieved after the HEP processes. We are making efforts to further improve the removal uniformity in the nine-cell cavity. Here, we report on a VEP of the 1.3 GHz Nb nine-cell cavity at a higher cathode rotation speed of 50 rpm. The VEP results reveal that the speed could be considered for improving the uniformity in removal while maintaining the surface smoothness. Required improvements in the VEP facility and acid flow condition for achieving uniform EP and a smooth surface are also described.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP021

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP022

Fermilab EP Facility Improvement

niobium, target, controls, SRF

453

F. Furuta, D.J. Bice, A.C. Crawford, T.J. Ring
Fermilab, Batavia, Illinois, USA

Electro-chemical Polishing (EP) is one of the key technologies of surface treatments for niobium superconducting cavities. We have established a single-cell scale horizontal electro-polishing facility at Fermilab and routinely processed the niobium cavities with the frequencies of 1.3 GHz to 3.9 GHz. The precise control of EP parameters, especially the temperatures of cavity outside wall, allows the uniform removal over the cell with the variation of ±15%. Here we report the details of our EP process and recent improvements on our EP facility at Fermilab.

Poster TUP022 [1.711 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP022

About •

paper received ※ 10 July 2019 paper accepted ※ 17 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP023

Experience of LCLS-II Cavities Radial Tuning at DESY

HOM, SRF, FEL, linac

456

A. Sulimov, J.H. Thie
DESY, Hamburg, Germany
A. Gresele
Ettore Zanon S.p.A., Nuclear Division, Schio, Italy
A. Navitski
RI Research Instruments GmbH, Bergisch Gladbach, Germany
A.D. Palczewski
JLab, Newport News, Virginia, USA

Radial tuning (rolling) was applied to three LCLS-II cavities to prevent that their lengths exceed the technical limits. The cavities have a reduced frequency due to additional material removal during cavity treatment well beyond the baseline recipe. The mechanical condition of the cavities was relatively soft because of the thermal history and the niobium manufacture requirement of an optimal flux expulsion. The niobium was highly recrystallized by 3 hours annealing at 900°C and 975°C respectively. Each cavity received an inner surface treatment of 200 µm electro-polishing (EP) and an external 30 µm buffered chemical polishing (BCP) as part of the baseline recipe. Each cavity received an addition ~100 µm of chemical removal along with a second annealing treatment before the radial tuning process. Detailed information about the accuracy and homogeneity of LCLS-II cavities rolling is presented as well as results of field distribution analysis for TM011 zero-mode with a comparison to standard cavities.

Poster TUP023 [0.521 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP023

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP024

Radial Tuning Devices for 1.3 GHz TESLA Shape Cavities

SRF, HOM, FEL, niobium

459

A. Sulimov, J.H. Thie
DESY, Hamburg, Germany

Radial tuning devices at DESY can be applied to any TESLA shape 1.3 GHz cavity to reduce its elongation due to excessive additional material removal (>300 µm) or to compensate critical manufacturing uncertainties. Radial deformation of cavity cells can be provided by a special chain or a rolling device with three rollers. The chain distributes the radial forces on the equator area around the cell. The rollers are moving radially in relation to the rotating cavity and provide an equator diameter reduction. Both devices have the contour close to the cell shape at the equator area. The required equator radius deviation depends on the tuning target and usually varies between (0.02…0.60) mm. Different aspects of the tuning procedure and material properties are described using the example of cavity rolling.

Poster TUP024 [0.252 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP024

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP026

Vibro-tumbling as an Alternative to Standard Mechanical Polishing Techniques for SRF Cavities

experiment, SRF, framework, superconductivity

464

E. Chyhyrynets, O. Azzolini, V.A. Garcia, G. Keppel, C. Pira, F. Stivanello, L. Zanotto
INFN/LNL, Legnaro (PD), Italy

Funding: Work supported by the INFN V group experiment TEFEN, Agreement N. KE2722/BE/FCC and from the European Union’s H₂020 Framework Programme under grant agreement no. 764879 (EASITrain)
Centrifugal Barrel Polishing (CBP) is a common tool in the Nb bulk SC cavities production, prior to elec-tropolishing (EP). Indeed, the mechanical polishing is fun-damental also in the superconducting thin film resonant cavities in which one of the main issues that limits the per-formances is the surface preparation. A promising vi-bro-tumbling technique is being studied and implemented with a possibility to replace or improve mechanical treat-ment steps (grinding, barrel polishing). The simplic-ity of the technology allows it to adapt to any cavity geom-etry, both for Nb and Cu materials. The presented work contains last results on 6 GHz cavities obtained at LNL-INFN, both Nb bulk and Cu cavities.

Poster TUP026 [5.584 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP026

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP027

Vertical Electropolishing of Niobium Nine-Cell Cavity with a Cavity Flipping System for Uniform Removal

cathode, niobium, experiment, SRF

467

K.N. Nii, V. Chouhan, Y.I. Ida, T.Y. Yamaguchi
MGH, Hyogo-ken, Japan
H. Hayano, S. Kato, H. Monjushiro, T. Saeki
KEK, Ibaraki, Japan

Marui Galvanizing Co., Ltd. has been developing vertical electropolishing (VEP) technology for single and nine-cell niobium superconducting radio frequency cavities using a unique cathode namely Ninja cathode in collaboration with KEK. The VEP process usually results in non-uniform removal with a large asymmetry along the cavity length. In order to suppress the asymmetry in removal, we are making different approaches. Flipping of the cavity during the VEP process is one of the approaches applied so far. A unique VEP setup, which allows the flipping of a multi-cell cavity, has been developed as reported earlier. Here, we report the improvement in the setup with automation for cavity flipping. VEP experiments were conducted with the improved system. VEP parameters were studied and the VEP results including the removal trend are discussed in detail.

Poster TUP027 [1.347 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP027

About •

paper received ※ 24 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP028

Development of Vertical Electropolishing Facility for Nb 9-Cell Cavity (3)

scattering, cathode, linac, controls

470

Y.I. Ida, V. Chouhan, K.N. Nii
MGH, Hyogo-ken, Japan
T. Akabori, G. Mitoya, K. Miyano
HKK, Morioka, Japan
Y. Anetai, F. Takahashi
WING. Co.Ltd, Iwate-ken, Japan
H. Hayano, S. Kato, H. Monjushiro, T. Saeki, M. Sawabe
KEK, Ibaraki, Japan

The 1st report was delivered in May, 2018 at the IPAC 18 in Vancouver, Canada. The 2nd report was delivered in September, 2018 at the LINAC 18 in Beijing, China. We will make our 3rd report in July, 2019 at the SRF-19 in Dresden, Germany. There will be two main points this time. The first is that by using our improved Ninja Electrode Premium, we can out-perform our number one and number two competitors in terms of uniform electropolishing of the interior of the 9-cell cavity. The second point is that we can remove hydrogen gas, reacted during electropolishing, from the cavity chambers in a manner that has not been successfully achieved by 1st report, May 2018 and 2nd report, September 2018. We will report our 9-cell vertical polishing revolver-type unit that solves the above two problems.

Poster TUP028 [0.444 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP028

About •

paper received ※ 24 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP029

An Experimental Analysis of Effective EP Parameters for Low-Frequency Cylindrical Nb Cavities

cathode, SRF, niobium, polarization

472

C.E. Reece
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. Work supported by the U.S. DoE, Office of Science, Office of Basic Energy Sciences.
While the basic process of electropolishing niobium with 1:9 HF:H₂SO₄ electrolyte has been well characterized, the specific process parameters used to electropolish different superconducting radio frequency (SRF) cavity geometries requires thoughtful attention. One seeks to realize confidently local diffusion-limited polishing at each point on the surface while maximizing uniformity of removal rate. Since the reaction rate is temperature dependent, this implies that one must manage the cavity surface temperature during polishing. Too-high applied voltage aggravates temperature and thus removal non-uniformity, but too-low applied voltage risks placing the large-diameter locations "off the current plateau," yielding etching rather than polishing. The majority of recent experience has been with elliptical L-band SRF cavities and some half-wave cavities at ANL. Lower frequency cavities with increased surface area and larger cathode-to-equator distance require fresh analysis and optimization. In preparation for SNS PPU project, JLab performed some EP process development runs with SNS high beta cavities to help identify viable parameter regimes for communication to cavity vendors. Results from this study are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP029

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP030

Automation of Particulate Characterization

controls, software, SRF, electron

477

J.K. Spradlin, C.E. Reece, O. Trofimova, A-M. Valente-Feliciano
JLab, Newport News, Virginia, USA

Funding: Notice: This manuscript has been authored by Jefferson Science Associates, LLC under Contract No. DE-AC05-06OR23177 with the U.S. Department of Energy.
Foreign particles residing on the field carrying surface of accelerator cavities are a known mechanism for field emission. Developing the methods and tools for collecting and characterizing particles found in an accelerator enables process development towards field emission free SRF cavities. Methods are presented for sampling assemblies, components, processes, and environmental conditions utilizing forensic techniques with specialized tooling. Sampling activities to date have produced an inventory of over 850 GSR spindles. Traditional SEM + EDS analysis of this volume of spindles is challenged by labor investment, spindle sampling methods, and the subsequent data pipeline which ultimately results in a statically inadequate dataset for any particulate distribution characterization. A complete systematic analysis of the spindles is enabled by third party software controlling SEM automation for EDS data acquisition. Details of spindle creation, collection equipment, component sampling, automating particle assessment, and data analysis used to characterize samples from beamline elements in CEBAF are presented.

Poster TUP030 [3.257 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP030

About •

paper received ※ 21 June 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP031

Heat Treatment for Jacketed Half-wave Resonator Cavity

cryomodule, vacuum, SRF, ECR

482

Y. Jung, B.H. Choi, D.H. Gil, M.O. Hyun, H. Kim, J.W. Kim, M.S. Kim, D.Y. Lee, J. Lee, S. Lee
IBS, Daejeon, Republic of Korea

Vertical tests of a prototype half-wave resonator cavity are being tested. The performance of the cavities, such as quality factor and accelerating electrical field, are measured and compared to the target design value. In previous study, we reported the effect of the heat treatment on a prototype bare HWR cavity. We baked a jacketed HWR cavity to improve a performance for 10 h at 650°C. In this study, we will report the effect of the heat treatment on the jacketed HWR cavity.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP031

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP032

Modal Analysis and Vibration Test for Quarter Wave Resonator for RAON

cryomodule, SRF, resonance, controls

485

M.O. Hyun, H.C. Jung, Y. Kim, M. Lee
IBS, Daejeon, Republic of Korea

Funding: This paper was supported by the Rare Isotope Science Project (RISP), which is funded by the Ministry of Science and ICT (MSIT) and National Research Foundation (NRF) of the Republic of Korea.
The Rare Isotope Science Project (RISP) in the Institute of Basic Science (IBS), Korea, is developing and con-structing the multi-purpose linear accelerator at the north side of Daejeon, South Korea. RISP accelerator (RAON) is composed with low-energy region (SCL3) and high-energy region (SCL2), and low-energy region is made with quarter-wave resonator (QWR) and half-wave resonator (HWR) when high-energy region is made with single spoke resonator type-1 (SSR1) and type-2 (SSR2). This paper shows about the initial resonance issues of QWR superconducting (SC) cavity during cold test and SRF disturbance measurement. Afterwards, this paper shows the modal analysis and vibration test of QWR SC cavity.

Poster TUP032 [0.584 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP032

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP033

Modal Analysis of the EXFEL 1.3 GHz Cavity and Cryomodule Main Components and Comparison with Measured Data

cryomodule, FEL, vacuum, linac

488

S. Barbanotti, A. Bellandi, J. Branlard, K. Jensch
DESY, Hamburg, Germany

Future upgrades of the European X-ray Free Electron Laser (EXFEL) may require driving the linac at higher duty factor, possibly extending to Continuous Wave (CW) mode. An R&D program has started at DESY, to prepare for a CW upgrade. Cryomodules are being tested in CW mode in our CryoModule Test Bench (CMTB) to study the performance and main issues for such an operation mode. Sensitivity to vibration causing microphonics is one of the main concerns for the CW operation in mode. Therefore a detailed analysis is being performed to evaluate the frequency spectrum of the EXFEL cryomodule main components: the cavity itself, the cavity string, the cold mass and the vacuum vessel. Finite Element Modal Analyses have been performed and the results compared with data measured at the CMTB. This paper summarizes the main results and conclusions of such a study.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP033

About •

paper received ※ 18 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP034

Microphonics Testing of LCLS II Cryomodules at Jefferson Lab

cryomodule, background, cryogenics, vacuum

493

T. Powers, N.C. Brock, G.K. Davis
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177
Jefferson Lab is partnering with Fermilab to build the 36 cryomodules for the LCLS II accelerator that will be installed at SLAC. The cavities have design loaded-Q of 4×10⁷, which means that it has a control bandwidth of 16 Hz. The JLab prototype cryomodule was instrumented with a series of seven accelerometers, and impulse hammer response measurements were made while the cryomodule was being built and after it was installed in the JLab cryomodule test facility. This was done so that we could understand the shapes of the modes of the structure. These results were compared to impulse hammer testing from the outside of the cryomodule and to individual cavity frequency shifts when the cryomodule was cold. The prototype cryomodule had excessive microphonics of 150 Hz peak due to a thermos-acoustic oscillation. Design modifications were implemented and subsequently the cryomodules had microphonics on the order of 10 to 20 Hz. Results of the modal analysis as well as the background microphonics observed when operated under various cryogenic conditions and with different modifications will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP034

About •

paper received ※ 21 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP036

Commissioning of Klystron Transmitters with 270 kW_CW at 1.3 GHz

klystron, GUI, power-supply, SRF

499

B. Schriefer, W. Anders, A. Heugel, H. Hoffmann, G. Mielczarek, H. Stein
HZB, Berlin, Germany

In Berlin-Adlershof the Helmholtz-Zentrum Berlin (HZB) is constructing the energy recovery linac ¿BERLinPro¿. Three klystron transmitters each 270 kWCW at 1.3 GHz are installed at the injection path of the ERL. The RF plant includes circulators and water loads. This paper describes the commissioning of the first klystron, calibration of the RF level control system as well as comparison with calorimetric output power measurements to verify the results.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP036

About •

paper received ※ 03 November 2019 paper accepted ※ 03 November 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP041

SRF testing for Mainz Energy Recovering Superconducting Accelerator MESA

cryomodule, SRF, radiation, controls

508

T. Stengler, K. Aulenbacher, F. Hug, S.D.W. Thomas
KPH, Mainz, Germany
K. Aulenbacher
GSI, Darmstadt, Germany
K. Aulenbacher
HIM, Mainz, Germany

Funding: This work is supported by the German Research Foundation (DFG) under the Cluster of Excellence "PRISMA+" EXC 2118/2019
The two superconducting radio frequency acceleration cryomodules for the new multiturn ERL ’Mainz Energy Recovering Superconducting Accelerator’ MESA at Johannes Gutenberg-Universität Mainz have been fabricated and are currently under testing at the Helmholtz Institut Mainz. These modules are based on the ELBE modules of the Helmholtz Center Dresden-Rossendorf but are modified to suit the high current and energy-recovering operation at MESA. The energy gain per module per turn should be 25 MeV, provided by two TESLA cavities, which were vertically tested at DESY, Hamburg, Germany. These tests showed an excellent performance of the quench limit and quality factor for three out of the four cavities. The fourth cavity has a lower but still acceptable quench limit and quality factor. In order to validate the performance of the fully assembled cryomodules after delivery to Mainz a test stand has been set up at the Helmholtz Institut Mainz. The test stand is described in detail and the status of the module testing is reported.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP041

About •

paper received ※ 21 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP042

Measurement of Mechanical Vibration of SRILAC Cavities

niobium, linac, ECR, cryomodule

513

O. Kamigaito, K. Ozeki, N. Sakamoto, K. Suda, K. Yamada
RIKEN Nishina Center, Wako, Japan

Mechanical vibration of quarter-wavelength resonators of SRILAC, the superconducting booster of the RIKEN heavy-ion linac, was measured during a vertical cold test. The measurements were performed for fully assembled cavities as well as for bare niobium cavities without the titanium jacket. In the procedure, the instantaneous resonant frequencies were measured for 10 seconds at a time interval of 1 ms and were recorded as a time series. The frequencies were analyzed by means of conventional signal analysis. The power spectrum was deduced from the autocorrelation function calculated with the fluctuation of resonant frequencies. Although the vibration amplitudes were smaller in the cavities assembled with the titanium jacket, we could not find a clear reason for this.

Poster TUP042 [6.957 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP042

About •

paper received ※ 27 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP043

Ab-initio Study of Atomic Scale Interaction Among Nb, Sn, Cl, and O

niobium, electron, SRF, superconductivity

518

A.B. Tesfamichael, T. Arias
Cornell University, Ithaca, New York, USA

Funding: Center for Bright Beam (CBB)
We employed a combination of ab-initio calculations and statistical mechanical models to understand the nature of atomic scale interaction among Nb, Sn, Cl, and O. Because of the profound nature of the interaction, we began our study by focusing only on the interaction of Nb with Sn in the absence of Cl and O. Using Density Functional Theory (DFT) we calculated: (1), binding energy of both vacant and interstitial of the super cell for both Nb and Sn atoms (2), rate of diffusion and re-evaporation upon transportation of Sn atom across z-axis from bulk Nb layer (3), electron transfer and electric field upon transportation of Sn atom both across z-axis and xy-plane from bulk Nb layer. Our calculation indicated 30-40% difference from experimental results. Therefore, we conclude that the presence of oxides is important and also Cl impurity can not not be avoided.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP043

About •

paper received ※ 24 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP046

Low Frequency, Low Beta Cavity Performance Improvement Studies

niobium, SRF, factory, vacuum

527

P. Kolb, R.E. Laxdal, Z.Y. Yao
TRIUMF, Vancouver, Canada

In recent years, new discoveries such as N₂ doping and infusion lead to a significant increases in Q₀ and accelerating gradient for 1.3 GHz, β=1 elliptical cavities. To understand and to adapt these treatments for lower frequency, \beta < 1 cavities, two coaxial test cavities, one quarter-wave resonator (QWR) and one half-wave resonator (HWR), have been built and put through a systematic study of these new treatments to show the effectiveness of these treatments at different frequencies. These cavities are tested in their fundamental mode and several higher order modes to study the frequency dependence of new cavity treatments such as N₂ doping and infusion. Results of these studies are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP046

About •

paper received ※ 22 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP049

Maximum Performance of Cavities Affected by the High-field Q-slope (HFQS)

SRF, experiment, niobium, radio-frequency

533

G. Ciovati
JLab, Newport News, Virginia, USA
A.V. Gurevich, I.P. Parajuli
ODU, Norfolk, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. The work of I. P. and A. G. is supported by NSF Grant PHY 100614-010.
The performance of high-purity, bulk niobium SRF cavities treated by chemical processes such as BCP or EP is limited by the so-called high-field Q-slope (HFQS). Several models and experimental studies have been proposed and performed over the years to understand the origin of these anomalous losses but a general consensus on what these orgins are is yet to be established. In this contribution, we present the results from the RF tests of several 1.3 GHz single-cell cavities limited by the HFQS and tested using a variable input coupler. This allowed to maintain close to critical coupling even at high field and the data showed that the HFQS did not saturate and that in some cases a power dissipation of up to 200 W at 2 K could be sustained without quench.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP049

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP050

A Multi-layered SRF Cavity for Conduction Cooling Applications

SRF, cryogenics, ECR, niobium

538

G. Ciovati, G. Cheng, E. Daly, G.V. Eremeev, J. Henry, R.A. Rimmer
JLab, Newport News, Virginia, USA
I.P. Parajuli
ODU, Norfolk, Virginia, USA
U. Pudasaini
The College of William and Mary, Williamsburg, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. Some of the work was supported by the 2008 PECASE Award of G. Ciovati. I. Parajuli is supported by NSF Grant PHYS-100614-010
Industrial application of SRF technology would favor the use of cryocoolers to conductively cool SRF cavities for particle accelerators, operating at or above 4.3 K. In order to achieve a lower surface resistance than Nb at 4.3 K, a superconductor with higher critical temperature should be used, whereas a metal with higher thermal conductivity than Nb should be used to conduct the heat to the cryocoolers. A standard 1.5 GHz bulk Nb single-cell cavity has been coated with a ~2 µm thick layer of Nb₃Sn on the inner surface and with a 5 mm thick Cu layer on the outer surface for conduction cooled applications. The cavity performance has been measured at 4.3 K and 2.0 K in liquid He. The cavity reached a peak surface magnetic field of ~40 mT with a quality factor of 6×10⁹ and 3.5×10⁹ at 4.3 K, before and after applying the thick Cu layer, respectively.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP050

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP051

Progress Towards Commissioning the Cornell DC Field Dependence Cavity

niobium, multipactoring, SRF, solenoid

543

J.T. Maniscalco, T. Gruber, A.T. Holic, M. Liepe
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA

The Cornell DC Field Dependence Cavity is a new coaxial test resonator designed to study the impact of strong (up to 200 mT or more) DC surface magnetic fields on the superconducting surface resistance, providing physical insight into the root of the ‘‘anti-Q-slope’’ and probing critical fields. In this report we report progress in the commissioning of this new apparatus, including finalized design elements and results of prototype tests.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP051

About •

paper received ※ 25 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP052

Design and Commissioning of a Magnetic Field Scanning System for SRF Cavities

SRF, cryogenics, data-acquisition, experiment

547

I.P. Parajuli, J.R. Delayen, A.V. Gurevich, J. Nice
ODU, Norfolk, Virginia, USA
G. Ciovati, W.A. Clemens, J.R. Delayen
JLab, Newport News, Virginia, USA

Funding: Work supported by NSF Grant 100614-010. G. C. is supported by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
Trapped magnetic vortices are one of the leading sources of residual losses in SRF cavities. Mechanisms of flux pinning depend on the materials treatment and cool-down conditions. A magnetic field scanning system using flux-gate magnetometers and Hall probes has been designed and built to allow measuring the local magnetic field of trapped vortices normal to the outer surface of 1.3 GHz single-cell SRF cavities at cryogenic temperatures. Such system will allow inferring the key information about the distribution and magnitude of trapped flux in the SRF cavities for different material, surface preparations and cool-down conditions.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP052

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP053

Optimal Thermal Gradient for Flux Expulsion in 600°C Heat-treated CEBAF 12 GeV Upgrade Cavities

HOM, niobium, experiment, controls

550

R.L. Geng, F. Marhauser, P.D. Owen
JLab, Newport News, Virginia, USA

We will present results on measurement of flux expulsion in CEBAF 12 GeV upgrade cavities and original CEBAF cavities and the search for optimal thermal gradient for reducing the trapped flux in cavities installed in CEBAF linacs. Preliminary measurements of one C100 cavities has shown that a nearly perfect flux expulsion can be achieved at an optimal thermal gradient - a surprising result contrary to the expectation of zero flux expulsion for 600°C heat treated niobium cavities. These results could lead to a cost-effective path for improving the quality factor of cavities installed in CEBAF and ultimately saving accelerator operation cost.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP053

About •

paper received ※ 24 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP054

How Is Flux Expulsion Affected by Geometry: Experimental Evidence and Model

niobium, experiment, SRF, accelerating-gradient

555

D. Longuevergne
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France

Measurements of magnetic sensitivity to trapped flux on several type of cavity geometries have been performed at IPNO showing a clear geometrical effect. Magnetic sensitivity depends not only on material quality but also on the cavity geometry and on the residual magnetic field orientation. A presentation of experimental data will be done. These will be as well compared to the theoretical magnetic sensitivities calculated thanks to a simple Labview routine

Poster TUP054 [1.312 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP054

About •

paper received ※ 03 July 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP055

Nonlinear Dynamics and Dissipation of Vortex Lines Driven by Strong RF Fields

ECR, radio-frequency, niobium, electron

560

M.R.P. Walive Pathiranage, A.V. Gurevich
ODU, Norfolk, Virginia, USA

Trapped vortices can contribute significantly to a residual surface resistance of superconducting radio frequency (SRF) cavities but the nonlinear dynamics of flexible vortex lines driven by strong rf currents has not been well understood. Here we report extensive numerical simulations of large-amplitude oscillations of a trapped vortex line under the strong rf magnetic field. The rf power dissipated by an oscillating vortex segment driven by the rf Meissner currents was calculated by taking into account the nonlinear vortex line tension, vortex mass and a nonlinear Larkin-Ovchinnikov and overheating viscous drag force. We calculated the field dependence of the surface resistance Rs and showed that at low frequencies Rs(H) increases with H but as the frequency increases, Rs(H) becomes a non-monotonic function of H which decreases with H at higher fields. These results suggest that trapped vortices can contribute to the extended Q(H) rise observed on the SRF cavities.

Poster TUP055 [1.744 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP055

About •

paper received ※ 23 June 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP056

A First-Principles Study on Magnetic Flux Trapping at Niobium Grain Boundaries

niobium, electron, simulation, radio-frequency

565

P. Garg, K.N. Solanki
Arizona State University, Tempe, USA
T.R. Bieler
Michigan State University, East Lansing, Michigan, USA
L.D. Cooley
NHMFL, Tallahassee, Florida, USA

Niobium is basis for all superconducting radio frequency cavities, a technology that accelerates charged particle beams to energy levels not possible by other means. When cavities are pushed to limits, significant heating appears at extended material defects, like grain boundaries. Therefore, it is crucial to understand how grain boundary (GB) structure and associated properties lead to trapping of magnetic field, and whether GB itself has any unusual magnetic behavior. Using first-principles calculations, external magnetic field along the GB plane was simulated within an all-electron full-potential linearized augmented plane-wave framework. A ground state with non-zero flux, indicative of flux trapping, was obtained at some grain boundaries, this outcome being influenced strongly by GB local structure. Furthermore, electronic density of states and charge-transfer calculations suggested non-zero spin polarization at grain boundaries, which may be consistent with recent observations of unusual paramagnetic magnetization as a function of specimen surface area for cavity-grade niobium.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP056

About •

paper received ※ 23 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP057

Study of Flux Trapping Variability between Batches of Tokyo Denkai Niobium used for the LCLS-II Project and Subsequent 9-cell RF Loss Distribution between the Batches

niobium, SRF, FEL, superconductivity

570

A.D. Palczewski
JLab, Newport News, Virginia, USA
D. Gonnella
SLAC, Menlo Park, California, USA
O.S. Melnychuk, D.A. Sergatskov
Fermilab, Batavia, Illinois, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
During the LCLS-II project a second batch of niobium was procured from Tokyo Denkai Co Ltd in order to make additional cavities. The original production material came from Two vendors Tokyo Denkai Co., Ltd. (TD) and Ningxia Orient Tantalum Industry Co., Ltd. (OTIC/NX)). It was found TD niobium required a lower annealing temperature (900°C) to obtain satisfactory flux expulsion characteristics compared to NX which required a slightly higher annealing temperature (950°-975°C). In order to ensure the new TD material performed equivalent to the niobium produced 4 year before after 900°C annealing; each heat lot of niobium had its flux expulsion characteristics parametrized and custom thermal treatments developed for each lot. Subsequent pure heat lot 9 cell cavities were made and tested. We will look at the flux expulsion characteristics of each lot, and RF loss of the 9-cell cavities produced using the individual heat lots.

Poster TUP057 [1.446 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP057

About •

paper received ※ 25 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP058

Characterization of Small AMR Sensors in Liquid Helium to Measure Residual Magnetic Field on Superconducting Samples

SRF, experiment, controls, site

576

G. Martinet
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France

Trapped residual magnetic flux is responsible of residual resistance degradation on superconducting materials used in SRF technologies. To characterize this effect on superconducting samples, compact sensors are required to mount on sample characterization devices. In this paper, we present results on AMR sensors supplied from different manufacturers in the temperature range from 4.2 K up to 300 K.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP058

About •

paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP059

Investigation of Trapped Flux Dynamics via DC-Magnetic Quenching

experiment, superconducting-cavity, ECR, SRF

580

P. Nuñez von Voigt, J. Knobloch, O. Kugeler
HZB, Berlin, Germany
J. Knobloch
University of Siegen, Siegen, Germany

Trapped magnetic flux increases the surface resistance in superconducting radio-frequency cavities. A better understanding of its behaviour could help to develop a method of expelling trapped flux from the superconducting surface. Using a superconducting coil with ferrite core attached to a 3 GHz sample Niobium cavity fully immersed in liquid Helium, we were able to subject the cavity walls to unusually large magnetic fields (estimated > 150 mT) and create magnetic quenches. With Fluxgate sensors attached in three spatial directions inside the cavity, we were able to monitor the quench dynamics and extract parameters of the flux dynamics from the hysteretic behaviour of the measured fields resulting from the applied coil current. First results of manipulation of the trapped flux with high magnetic fields are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP059

About •

paper received ※ 24 June 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP060

Development of Temperature and Magnetic Field Mapping System for Superconducting Cavities at KEK

controls, solenoid, site, radio-frequency

583

T. Okada, E. Kako, T. Konomi, H. Sakai, K. Umemori
Sokendai, Ibaraki, Japan
E. Kako, T. Konomi, M. Masuzawa, H. Sakai, K. Tsuchiya, R. Ueki, K. Umemori
KEK, Ibaraki, Japan
A. Poudel, T. Tajima
LANL, Los Alamos, New Mexico, USA

A temperature and magnetic field mapping system for a single cell superconducting cavity is being developed at KEK. The mapping system is used to observe the temperature distribution and the ambient magnetic field distribution around the outer surface of the cavity. A total of 36 boards at every 10 degrees are attached on the cavity. Each board consists of 15 carbon resistors of 100 Ω at room temperature and 3 AMR sensors of X, Y and Z directions at the equator. The calibration of the resisters and AMR sensors were carefully and precisely carried out at low temperature. The data logging system using NI loggers is enabled to measure within 1 ms in the whole cavity surface. The initial test results in the vertical test of the single-cell cavity will be reported in this paper.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP060

About •

paper received ※ 05 July 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP061

Gradients of 50 MV/m in TESLA Shaped Cavities via Modified Low Temperature Bake

niobium, SRF, ECR, site

586

D. Bafia, J. Zasadzinski
IIT, Chicago, Illinois, USA
D. Bafia, A. Grassellino, O.S. Melnychuk, A.S. Romanenko, Z-H. Sung
Fermilab, Batavia, Illinois, USA

This paper will discuss the 75/120 C modified low temperature bake capable of giving unprecedented accel-erating gradients of above 50 MV/m for 1.3 GHz TESLA-shaped niobium SRF cavities in CW operation. A bifurca-tion in the Q₀ vs E_acc curve is observed after retesting cavities without disassembly in between, yielding per-formance that ranges from exceptional to above state-of-the-art. Atomic Force Microscopy studies on cavity cut-outs gives a possible mechanism responsible for this branching in performance, namely, the dissociation and growth of room temperature niobium nano-hydrides that exist near the RF surface, which are made superconduct-ing only through the proximity effect. In-situ low temper-ature baking of cavity cutouts reveals a dissociation of these room temperature nano-hydrides, which could ex-plain the higher performance of cavities subject to similar in-situ heating in the dewar.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP061

About •

paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP062

New Insights in the Quench Mechanisms in Nitrogen Doped Cavities

SRF, accelerating-gradient, niobium, factory

592

D. Bafia, J. Zasadzinski
IIT, Chicago, Illinois, USA
D. Bafia, D.J. Bice, A. Grassellino, O.S. Melnychuk, A.S. Romanenko, D.A. Sergatskov
Fermilab, Batavia, Illinois, USA
D. Gonnella
SLAC, Menlo Park, California, USA
A.D. Palczewski
JLab, Newport News, Virginia, USA

This paper will cover a systematic study of the quench in nitrogen doped cavities: three cavities were sequentially treated/reset with different doping recipes which are known to produce different levels of quench field. Analysis of mean free path and TMAP coupled with sample analysis reveals new insights on the physics of the premature quench in nitrogen doped cavities; new recipes demonstrate the possibility to increase quench fields well beyond 30 MV/m.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP062

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP064

Flashover on RF Window of HWR SRF Cavity

pick-up, electron, SRF, linac

597

X. Liu, Z. Gao, Y. He, G. Huang
IMP/CAS, Lanzhou, People’s Republic of China

Breakdown on the RF ceramic windows always happen in different kinds of accelerator. It is one of the main limitations in current day superconducting cavities and couplers. The PT signal trip caused by discharge on the surface of RF ceramic window lead LLRF control system trip which affect the stable operation of the superconducting linac. Simulation of field emission electron trajectory in superconducting cavity and experimental measurements of the frequency of the pickup signal trip have been performed. A lot of aged window with characteristics of flashover were studied by means of material characterization. The flashover on the surface of RF ceramic window caused by electrons and field emission provide the origin of initial electrons. A modified design of the pickup antenna have solved the PT pickup trip problem.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP064

About •

paper received ※ 23 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP066

New Design of SSR2 Spoke Cavity for PIP II SRF Linac

quadrupole, multipactoring, linac, HOM

600

P. Berrutti, I.V. Gonin, T.N. Khabiboulline, M. Parise, D. Passarelli, G.V. Romanov, F. Ruiu, A.I. Sukhanov, V.P. Yakovlev
Fermilab, Batavia, Illinois, USA

Funding: US Department of Energy
Superconducting SSR2 spoke cavities provide acceleration of the H⁻ in PIP II SRF linac from 35 to 185 MeV. The RF and mechanical design of the SSR2 cavities has been completed and satisfies the technical requirements. However, our resent results of the high RF power tests of fully dressed SSR1 cavities show considerably strong multipacting (MP), which took significant time to process. On the other hand, the new results of the tests of balloon cavity showed significant mitigation of MP. In this paper we present the results of the improved design of the SSR2 cavity, based on the balloon cavity concept. The electromagnetic design is presented, including RF parameter optimization, MP simulations, field asymmetry analysis, High Order Mode (HOM) calculations. Mechanical analysis of the dressed cavity is presented also, which includes Lorentz Force Detuning optimization, and reduction of the cavity resonance frequency sensitivity versus He pressure fluctuations. The design completely satisfies the PIP II technical requirements.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP066

About •

paper received ※ 21 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP068

Study of Surface Treatment of 1.3 GHz Single-cell Copper Cavity for Niobium Sputtering

SRF, niobium, experiment, MMI

605

F.Y. Yang, J. Dai, P. He, Z.Q. Li, Y. Ma, P. Zhang
IHEP, Beijing, People’s Republic of China

Funding: This work has been supported in part by PAPS project and National Key Programme for S&T Research and Development (Grant NO.: 2016YFA0400400)
A R&D program on niobium sputtering on copper cavities has started at IHEP in 2017. Single-cell 1.3 GHz copper cavity has been chosen as a substrate. A chemical polishing system has subsequently developed and commissioned recently to accommodate the etching of both copper samples and a cavity. Different polishing agents have been tested on copper samples and later characterized. The results of these surface treatment tests are presented.

Poster TUP068 [1.228 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP068

About •

paper received ※ 20 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP070

The SRF Thin Film Test Facility in LHe-Free Cryostat

cryogenics, SRF, vacuum, controls

610

O.B. Malyshev, J.A. Conlon, P. Goudket, N. Pattalwar, S.M. Pattalwar
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
G. Burt
Cockcroft Institute, Warrington, Cheshire, United Kingdom
G. Burt
Lancaster University, Lancaster, United Kingdom

An ongoing programme of development superconducting thin film coating for SRF cavities requires a facility for a quick sample evaluation at the RF conditions. One of the key specifications is a simplicity of the testing procedure, allowing an easy installation and quick turnover of the testing samples. Choked test cavities operating at 7.8 GHz with three RF chokes have been designed and tested at DL in a LHe cryostat verifying that the system could perform as required. Having a sample and a cavity physically separate reduces the complexity involved in changing samples (major causes of low throughput rate and high running costs for other test cavities) and also allows direct measurement of the RF power dissipated in the sample via power calorimetry. However, changing a sample and preparation for a test requires about two-week effort per sample. In order to simplify the measurements and achieve a faster turnaround, a new cryostat cooled with a closed-cycle refrigerator has been designed, built and tested. Changing a sample, cooling down and testing can be reduced to 2-3 days per sample. Detailed design and results of testing of this facility will be reported at the conference.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP070

About •

paper received ※ 21 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP072

The Development of Niobium Sputtering on Copper Cavities at IHEP

niobium, vacuum, SRF, photon

613

J. Dai, P. He, Z.Q. Li, Y. Ma, F.Y. Yang, P. Zhang
IHEP, Beijing, People’s Republic of China

A R&D program focusing on niobium sputtering on copper cavities started at IHEP in 2017. Single-cell 1.3 GHz elliptical cavity shape has been initially chosen as sputtering substrate. A magnetron sputtering system have been developed in 2018. In addition, a surface treatment facility to polish the copper substrate before sputtering has been developed and commissioned. This paper will present the Nb/Cu coating activities at IHEP.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP072

About •

paper received ※ 19 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP073

Superconducting Thin Films Characterization at HZB with the Quadrupole Resonator

SRF, quadrupole, niobium, FEL

616

D.B. Tikhonov, S. Keckert, J. Knobloch, O. Kugeler, Y. Tamashevich
HZB, Berlin, Germany
A-M. Valente-Feliciano
JLab, Newport News, Virginia, USA

Funding: EASITrain - European Advanced Superconductivity Innovation and Training. This Marie Sklodowska-Curie Action Innovative Training Networks founded by H₂020 under Grant Agreement no. 764879
Superconducting thin films have great potential as post-Nb material for use in SRF applications in future accelerators and industry. To test the RF-performance of such films in practice, would require the building and coating of a full RF cavity. Deposition of thin films on such scales in test facilities are challenging, in particular when curved surfaces have to be coated. This greatly complicates their systematic research. In this contribution we report on the method we use to characterize small and flat thin film samples (Deposited onto both Nb and Cu substrates) in an actual cavity named the Quadrupole Resonator (QPR). We also summarize the latest measurement results of NbTiN thin films. The Quadrupole Resonator at HZB is a tool that is able to perform SRF characterizations at frequencies ~415, 847, 1300 MHz with RF fields using an RF-DC power compensation technique.

Poster TUP073 [2.318 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP073

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP075

New Progress for Nb Sputtered 325 MHz QWR Cavities in IMP

target, experiment, SRF, niobium

621

F. Pan, H. Guo, Y. He, T.C. Jiang, C.L. Li, M. Lu, T. Tan
IMP/CAS, Lanzhou, People’s Republic of China

Comparing with bulk niobium cavities, the Nb/Cu cavities feature a much better stability at 4.5 K. Last year, two 325 MHz QWR copper cavities coated with biased DC diode sputterred Nb for CiADS has been accomplished at IMP. But vertical tests showed the cavities had low Q₀ at 4 K. To solve the issue, a new coating system was designed and built. The sputtering target was redesigned and manufactured. The coating parameters were selected again and auxiliary heating was used to control the coating temperature in the process of sputtering. The power and Ar pressure during coating were also carefully selected. The paper covers resulting film characters, vertical tests with the evolution of the sputtering process, and improvements we made since last year.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP075

About •

paper received ※ 22 June 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP076

Electrochemical Deposition of Nb₃Sn on the Surface of Cu Substrates

niobium, site, controls, SRF

624

M. Lu, Q.W. Chu, Y. He, Z.Q. Lin, F. Pan, T. Tan, Z.Q. Yang
IMP/CAS, Lanzhou, People’s Republic of China

Coating superconducting Nb₃Sn thin film on the inner surface of a superconducting RF cavity is one of the most promising approaches to improve the performance of the accelerating cavity. Compared with traditional evaporation and sputtering, electrochemical coating has the advantages on process simplicity, low cost and mass production. However, the conventional electroplating, because of its low growth temperature and aqueous reaction environment, tends to produce porous, loosely bonded, and often contaminated film. All these properties result in excessive pinning center and deteriorate the superconducting radio frequency cavities performance. In this paper, a new method including multi-layer electroplating and heat treatment is used to deposit Nb₃Sn thin film on top of copper substrates. Important growth parameters, e.g. electrical current density, layer thickness ratio, and annealing temperature are studied. The morphology of the film surfaces was observed by scanning electron microscope (SEM) and the structure of the film was analyzed by X-ray diffraction (XRD). The results showed that a flat and uniform Nb₃Sn layer on copper can be obtained, and the thickness is about 7 micron.

Poster TUP076 [0.716 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP076

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP077

Nb₃Sn Thin Film Coating Method for Superconducting Multilayered Structure

site, SRF, target, experiment

628

R. Ito, T. Nagata
ULVAC, Inc, Chiba, Japan
H. Hayano, R. Katayama, T. Kubo, T. Saeki
KEK, Ibaraki, Japan
H. Ito
Sokendai, Ibaraki, Japan
Y. Iwashita
Kyoto ICR, Uji, Kyoto, Japan

S-I-S (superconductor-insulator-superconductor) multilayered structure has been proposed in order to increase the maximum acceleration gradient of SRF cavities. Nb₃Sn is the material most expected as a superconducting layer of the S-I-S multilayered structure because it offers both a large critical temperature and large predicted Hsh. Most important in fabricating Nb₃Sn thin films is the stoichiometry of the material produced, and the lack of tin leads to performance degradation. We have launched a new in-house DC magnetron sputtering apparatus for Nb₃Sn deposition. Nb and Sn layers were alternately and repeatedly deposited on Si wafer while adjusting the film thickness of each layer, so we successfully obtained Nb-Sn films having appropriate composition ratio. The as-deposited films were annealed under the temperature of 600 degree C for 1 hour to generate the Nb₃Sn phase. The characteristics of Nb-Sn films evaluated by XRD, XRF, FE-SEM, and so on. We also measured critical temperature of the annealed films. In this paper, the detail of the Nb₃Sn coating method and the measurement result of the Nb-Sn films will be reported.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP077

About •

paper received ※ 02 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP078

Lower Critical Field Measurement of NbN Multilayer Thin Film Superconductor at KEK

solenoid, SRF, shielding, radio-frequency

632

H. Ito
Sokendai, Ibaraki, Japan
C.Z. Antoine
CEA-IRFU, Gif-sur-Yvette, France
H. Hayano, R. Katayama, T. Kubo, T. Saeki
KEK, Ibaraki, Japan
R. Ito, T. Nagata
ULVAC, Inc, Chiba, Japan
Y. Iwashita, H. Tongu
Kyoto ICR, Uji, Kyoto, Japan

Funding: The work is supported by Japan Society for the Promotion of Science Grant-in-Aid for Young Scientist (A) No.17H04839.
The multilayer thin film structure of the superconductor has been proposed by A. Gurevich to enhance the maximum gradient of SRF cavities. The lower critical field Hc1 at which the vortex start penetrating the superconducting material will be improved by coating Nb with thin film superconductor such as NbN. It is expected that the enhancement of Hc1 depends on the thickness of each layer. In order to determine the optimum thickness of each layer and to compare the measurement results with the theoretical prediction proposed by T. Kubo, we developed the Hc1 measurement system using the third harmonic response of the applied AC magnetic field at KEK. For the Hc1 measurement without the influence of the edge or the shape effects, the AC magnetic field can be applied locally by the solenoid coil of 5mm diameter in our measurement system. ULVAC made the NbN-SiO₂ multilayer thin film samples of various NbN thicknesses. In this report, the measurement result of the bulk Nb sample and NbN-SiO₂ multilayer thin film samples of different thickness of NbN layer will be discussed.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP078

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP079

Deposition of Nb₃Sn Films by Multilayer Sequential Sputtering for SRF Cavity Application

SRF, site, FEL, niobium

637

Md.N. Sayeed, H. Elsayed-Ali
ODU, Norfolk, Virginia, USA
M.C. Burton, G.V. Eremeev, C.E. Reece, A-M. Valente-Feliciano
JLab, Newport News, Virginia, USA
U. Pudasaini
The College of William and Mary, Williamsburg, Virginia, USA

Nb₃Sn is considered as an alternative of Nb for SRF accelerator cavity application due to its potential to obtain higher quality factors and higher accelerating gradients at a higher operating temperature. Magnetron sputtering is one of the effective techniques that can be used to fabricate Nb₃Sn on SRF cavity surface. We report on the surface properties of Nb₃Sn films fabricated by sputtering multiple layers of Nb and Sn on sapphire and niobium substrates followed by annealing at 950°C for 3 h. The crystal structure, film microstructure, composition and surface roughness were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and atomic force microscopy (AFM). The RF performance of the Nb₃Sn coated Nb substrates were measured by a surface impedance characterization system. We also report on the design of a multilayer sputter deposition system to coat a single-cell SRF cavity.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP079

About •

paper received ※ 22 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP080

Tuner Design and Test for 166.6 MHz SRF Cavity of HEPS

SRF, simulation, high-voltage, LLRF

642

Z.H. Mi, Z.Q. Li, H.Y. Lin, W.M. Pan, Q.Y. Wang, P. Zhang, X.Y. Zhang, H.J. Zheng
IHEP, Beijing, People’s Republic of China

The 166.6 MHz superconducting RF cavities have been proposed for the High Energy Photon Source (HEPS), a 6 GeV kilometer-scale light source. The cavity is of quarter-wave type made of bulk niobium with ¿=1. Each cavity will be operated at 4.2 K providing 1.2 MV accelerating. To compensate the frequency change due to manufacturing uncertainty, Lorentz force, beam loading, He pressure and microphonics the plunger tuner and gap tuner are chosen as options. Now the plunger tuner and low temperature gap tuner have been test with cavity, while the warm gap tuner is being designed. Details of the design and summary of the test results of the two type tuners with cavity are presented in this paper.

Poster TUP080 [1.141 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP080

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP081

Status of the HL-LHC Crab Cavity Tuner

cryomodule, GUI, SRF, vacuum

646

K. Artoos, L. Arnaudon, R. Calaga, E. Cano-Pleite, O. Capatina, T. Capelli, D.F. Cartaxo dos Santos, M. Garlasché, D.C. Glenat, A. Krawczyk, R. Leuxe, P. Minginette, J.S. Swieszek
CERN, Geneva, Switzerland
T.J. Jones
STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom
A. Krawczyk, B. Prochal
IFJ-PAN, Kraków, Poland
J.A. Mitchell
Lancaster University, Lancaster, United Kingdom
S. Verdú-Andrés
BNL, Upton, New York, USA

Funding: Research supported by the HL-LHC project
The resonance frequency of the HL-LHC Double Quarter Wave (DQW) and Radio Frequency Dipole (RFD) crab cavities is set to the operating frequency of 400.79 MHz by deforming the cavities. For both types of cavities, the tuning principle foresees a symmetric mechanical deformation of parts of the cavities in vertical direction, with the tuner motor placed outside on top of the vacuum vessel. The tuner design was successfully tested on the DQW prototype cryomodule with two cavities in 2018 in the SPS at CERN. This paper describes the design of DQW and RFD crab tuners. The experience and results of assembly and cold testing is given together with some required improvements. Finally, the final series crab tuners preparation is reported.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP081

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP083

Performance of the 650 MHz SRF Cavity Tuner for PIP II Project

SRF, cryomodule, interface, resonance

652

Y.M. Pischalnikov, S.K. Chandrasekaran, S. Cheban, I.V. Gonin, T.N. Khabiboulline, V.P. Yakovlev, J.C. Yun
Fermilab, Batavia, Illinois, USA
C. Contreras-Martinez
FRIB, East Lansing, Michigan, USA

The PIP-II linac will include fifty seven 650MHz SRF cavities. Each cavity will be equipped with tuner for coarse and fine frequency tuning. Design and operations parameters will be discussed. Results from room temperature tests with prototype tuner installed on a 650MHz ¿_G=0.90 elliptical cavity will be presented.

Poster TUP083 [1.567 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP083

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP084

Testing of the Piezo-actuators at High Dynamic Rate Operational Conditions

SRF, operation, vacuum, linac

656

Y.M. Pischalnikov, J.C. Yun
Fermilab, Batavia, Illinois, USA
C. Contreras-Martinez
FRIB, East Lansing, Michigan, USA

Reliability of the piezo-actuators that deployed into SRF cavity tuner and operated at high dynamic rate operational conditions made significant impact on the overall performance of the SRF linacs. We tested at FNAL piezo-actuators P-P-844K075 that were developed at Physik Instrumente for LCLS II project. Even these actuators were developed for CW linac we tested them at high dynamic rate inside cryogenic/insulated vacuum environment. Results of the tests will be presented. Different modes of the piezo-actuators failure will be discussed.

Poster TUP084 [3.168 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP084

About •

paper received ※ 23 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP085

Operation of an SRF Cavity Tuner Submerged into Liquid He

experiment, SRF, resonance, operation

660

Y.M. Pischalnikov, D.J. Bice, A. Grassellino, T.N. Khabiboulline, O.S. Melnychuk, R.V. Pilipenko, S. Posen, O.V. Pronitchev, A.S. Romanenko
Fermilab, Batavia, Illinois, USA

To precisely control the resonance of 1.3 GHz SRF cavities during testing at the FNAL’s Vertical Test Facility, we install for the first time a double lever tuner and operate it when submerged into the liquid He bath. Both active components of the tuner: electromechanical actuator (stepper motor) and piezo-actuators are operated inside superfluid helium. Accuracy in controlling the SRF cavity resonance frequency will be presented. Specifics of the tuner operation when submerged into liquid He will be discussed.

Poster TUP085 [2.164 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP085

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP086

Frequency Tuning System Based on Mobile Plungers For Superconductive Coaxial Half Wave Resonators

simulation, linac, SRF, vacuum

664

D. Bychanok, S. Huseu, S.A. Maksimenko
INP BSU, Minsk, Belarus
A.V. Butenko, E. Syresin
JINR, Dubna, Moscow Region, Russia
E.A. Gurnevich
Belarussian State University, Scientific Research Institute of Nuclear Problems, Minsk, Belarus
M. Gusarova, M.V. Lalayan, S.M. Polozov
MEPhI, Moscow, Russia

The design of a prototype of the frequency tuning system (FTS) for superconductive coaxial half wave cavities (HWR) [1] developed for the Nuclotron-based Ion Collider fAcility (NICA) injector is presented. The proposed system is based on mobile plungers placed in the technological holes in the end caps of the resonator. The FTS allows controlling the penetration depth of plungers, which is monotonically related to the resonant frequency shift of the cavity. The developed FTS includes slow/fast tuner parts and is more compact and simple in comparison to traditional mechanical systems, which deform reversibly the HWR by applying an effort on the beam ports [2]. The similar plunger-based tuner design was considered for QWR cavities in [3]. The results of numerical simulations of the resonant frequency for a wide range of plunger parameters are presented and discussed. The most important parameters for effective frequency shift are estimated.
[1] S. Matsievskiy et al., RuPAC’18. doi:10.18429/JACoW-RUPAC2018-WEPSB48
[2] N. Misiara et al., LINAC’16. doi:10.18429/JACoW-LINAC2016-MOPRC026
[3] D. Longuevergne et al., ‘‘A cold tuner system with mobile plunger’’, in Proc. SRF2013, paper THIOD04.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP086

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP087

Development and Performances of Spoke Cavity Tuner for MYRRHA Linac Project

controls, linac, simulation, operation

667

N. Gandolfo, S. Blivet, P. Duchesne, D. Le Dréan
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France

In the framework of the Multi-purpose hYbrid Research Reactor for High-tech Applications (MYRRHA) 100 MeV linac construction, a fully equipped prototype cryomodule is being developed. In order to control the resonance frequency of the cavities during operation, a tuner has been studied with the specific requirements: high degree of reliability and high tuning speed. This paper reports the design consideration and the first performances measurement in vertical cryostat test at an early stage of the prototyping phase.

Poster TUP087 [2.367 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP087

About •

paper received ※ 01 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP092

Experiences of Superconducting Radio Frequency Coldmass Production for the FRIB Linear Accelerator

cryomodule, vacuum, solenoid, SRF

675

K. Elliott, B.W. Barker, C. Donald, E.S. Metzgar, L. Popielarski, D.R. Victory, J.D. Whaley, M.S. Wilbur
FRIB, East Lansing, Michigan, USA

Funding: *Work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661 and the National Science Foundation under Cooperative Agreement PHY-1102511.
The superconducting radio frequency (SRF) portion of the Facility for Rare Isotope Beams (FRIB) linear accelerator consists of 46 cryomodules of 6 different types. Each cryomodule contains a coldmass consisting of a string of SRF resonators. There are four different types of resonators; a β=0.041 quarter wavelength resonator (QWR), a β=0.085 QWR, a β=0.29 half wavelength resonator (HWR), and a β=0.53 HWR. In total there are 324 SRF resonators in the FRIB linear accelerator. This paper provides a summary of experiences from the assembly of all FRIB coldmass types in a clean room environment.

Poster TUP092 [1.481 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP092

About •

paper received ※ 23 June 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP093

Summary of FRIB Cavity Processing in the SRF Coldmass Processing Facility and Lessons Learned

niobium, SRF, linac, controls

680

E.S. Metzgar, B.W. Barker, K. Elliott, W. Hartung, L. Popielarski, G.V. Simpson, D.R. Victory, J.D. Whaley
FRIB, East Lansing, Michigan, USA

Funding: Work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661 and the National Science Foundation under Cooperative Agreement PHY-1102511.
Baseline coldmass production for the linear particle accelerator at the Facility for Rare Isotope Beams (FRIB) is nearing completion. This paper will review the processing of cavities through the FRIB superconducting radio frequency (SRF) coldmass production facility focusing on chemical processing and high-pressure rinsing. Key processing data will be compiled and correlations between processing variables and cavity RF testing results will be examined.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP093

About •

paper received ※ 22 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP094

Improvements to LCLS-II Cryomodule Transportation

cryomodule, vacuum, ISOL, SRF

684

N.A. Huque, E. Daly, P.D. Owen
JLab, Newport News, Virginia, USA
B.D. Hartsell, J.P. Holzbauer
Fermilab, Batavia, Illinois, USA

The Linear Coherent Light Source (LCLS-II) is currently being constructed at the SLAC National Laboratory. A total of 35 cryomodules will be fabricated at Jefferson Lab (JLab) in Virginia and Fermi National Laboratory (FNAL) in Illinois and transported via road to SLAC. A shipping frame with an inner bed isolated by springs was designed to protect the CMs from shocks and vibrations during shipments. Successful road testing of the JLab prototype paved the way for production CM shipments. The initial production shipments lead to several catastrophic failures in beamline vacuum in the cryomodules. The failures were determined to be due to fatigue in Fundamental Power Coupler (FPC) bellows due to excessive motion during shipment. A series of instrumented CM shipping tests and component tests were undertaken to develop a solution. A modified spring layout was tested and implemented, which reduced shocks on the CMs. FPC coupler bellows restraints were tested on a shaker table and on a CM during shipping; they were able to reduce bellows motion by a factor of three. The updated shipping system is currently in use and has successfully delivered six cryomodules to SLAC from JLab and FNAL.

Poster TUP094 [0.958 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP094

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP095

Lessons Learned Assembling the SSR1 Cavities String for PIP-II

vacuum, solenoid, cryomodule, SRF

690

D. Passarelli, D.J. Bice, M. Parise, T.J. Ring, G. Wu
Fermilab, Batavia, Illinois, USA
S. Berry
CEA-DRF-IRFU, France

The string assembly of the prototype Single Spoke Resonator type 1 (SSR1) cryomodule for PIP-II at Fermilab was successfully completed. Lessons learned from the preparation, assembly and the quality control activities of the final fully integrated assembly will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP095

About •

paper received ※ 28 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP096

Optimization of Clean Room Infrastructure and Procedure During LCLS-II Cryomodule Production at Fermilab

cryomodule, vacuum, detector, linac

695

G. Wu, S.D. Adams, T.T. Arkan, M.A. Battistoni, D.J. Bice, M.B. Chlebek, E.R. Harms, B.M. Kuhn, A.M. Rowe
Fermilab, Batavia, Illinois, USA
S. Berry, O. Napoly
CEA-DRF-IRFU, France

Funding: The work is supported by Fermilab which is operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
Optimization of Fermilab string assembly procedure and infrastructure has yielded a significant improvement of cryomodule particulate counts. Late production of LCLS-II cryomodules were tested at CMTF at Fermilab and showed little to no x-ray up to administrative limit. The paper describes the field emission measurement instrumentation, field emission results of LCLS-II cyomodules, clean room infrastructure upgrade and procedure optimization.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP096

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP098

Preparation for the Advanced Demonstrator Testing at GSI

solenoid, linac, cryomodule, heavy-ion

698

V. Gettmann, K. Aulenbacher, W.A. Barth, F.D. Dziuba, M. Heilmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu, S. Yaramyshev
GSI, Darmstadt, Germany
K. Aulenbacher, W.A. Barth, F.D. Dziuba, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu
HIM, Mainz, Germany
K. Aulenbacher, F.D. Dziuba, S. Lauber
IKP, Mainz, Germany
M. Basten, H. Podlech, M. Schwarz
IAP, Frankfurt am Main, Germany

The superconducting (sc) heavy ion Helmholtz Linear Accelerator (HELIAC) is under development at GSI. As a first step, the cw-Linac demonstrator was the first part for the proposed cw-LINAC@GSI. A superconducting CH-cavity, embedded by two superconducting solenoids has been tested with beam in 2017/2018 successfully. The sc CH-structure, designed at Goethe-University of Frankfurt, is the key component and offers a variety of research and development. As a next step the first cryostat of the HELIAC, the so called Advanced Demonstrator will be tested in the same testing environment at GSI. Therefore, a bigger concrete Bunker as well as the connection to the cryo plant is under development. The cold string was assembled in a rehabilitated clean room at GSI. For future clean room assemblies a fully equipped clean room is under preparation at Helmholtz-Institut Mainz. The mechanical suspension, composed of hanging components on crossed steel ropes, is a reliable concept to prevent the displacement during cool down. The cryogenic systems as well as all other mechanical tasks were solved. These and the future Advanced Demonstrator preparation will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP098

About •

paper received ※ 22 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP099

Particulate Sampling and Analysis During Refurbishment of Prototype European XFEL Cryomodule

FEL, SRF, cryomodule, superconductivity

701

N. Krupka, C. Bate, D. Reschke, S. Saegebarth, M. Schalwat, P. Schilling, S. Sievers
DESY, Hamburg, Germany

Funding: This work was supported by the Helmholtz Association within the topic Accelerator Research and Development (ARD) of the Matter and Tech-nologies (MT) Program.
The cryomodule PXFEL3₁ is one of three prototype cryomodules for the European XFEL. In preparation of the series module assembly it was used for the qualification of infrastructure and personnel at CEA Saclay. After transport and tests at DESY the cryomodule was stored for several years. Last year we decided to refurbish this module with new cavities for the installation in the FLASH accelerator. During the disassembly of the cavity string in the clean room at DESY we took several particulate samples for analysis. Optical and laser optical microscopy give us an insight on the quantity and type of the particulates. We expect to get hints where the particulates come from and how they are transported through the cavity string during transport and operation.

Poster TUP099 [2.599 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP099

About •

paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP100

Thermal Load Studies on the Photocathode Insert with Exchangeable Plug for the BERLinPro SRF-Photoinjector

cathode, SRF, experiment, gun

705

J. Kühn, N. Al-Saokal, M. Bürger, M. Dirsat, A. Frahm, A. Jankowiak, T. Kamps, G. Klemz, S. Mistry, A. Neumann, H. Plötz
HZB, Berlin, Germany

For the operation of an SRF photoinjector a well-functioning and efficient cooling system of the photocathode is necessary. A test experiment was set up of the photocathode cooling system based on the original components, which we call thermal contact experiment (TCX). We present the results of our thermal load studies on the photocathode insert with exchangeable photocathode plug. The goal was to test all components before they are installed in the cold string of the BERLinPro SRF-Photoinjector to ensure the operation of very sensitive semiconductor photocathodes. The tests include the investigation of the cooling performance, the thermal load management and the mechanical stability of the photocathode insert.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP100

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP101

LCLS-II Cryomodules Production Experience and Lessons Learned at Fermilab

cryomodule, vacuum, FEL, linac

709

T.T. Arkan, J.N. Blowers, C.M. Ginsburg, C.J. Grimm, J.A. Kaluzny, T.H. Nicol, Y.O. Orlov, K.S. Premo, R.P. Stanek, G. Wu
Fermilab, Batavia, Illinois, USA

LCLS-II is a planned upgrade project for the linear coherent light source (LCLS) at SLAC. The LCLS-II Linac will consist of thirty-five 1.3 GHz and two 3.9 GHz superconducting RF continuous wave (CW) cryomodules that Fermilab and Jefferson Lab are currently producing in collaboration with SLAC. The LCLS-II 1.3 GHz cryomodule design is based on the European XFEL pulsed-mode cryomodule design with modifications needed for CW operation. Two prototype cryomodules had been assembled and tested. After prototype cryomodule tests, both laboratories have increased their cryomodule production rate to meet the challenging LCLS-II project installation schedule requirements of approximately one cryomodule per month per laboratory. To date, Fermilab has completed the assembly and testing of sixteen 1.3 GHz cryomodules. Fermilab has successfully shipped five CMs to SLAC and will continue to ship with a two-week throughput. The first 3.9 GHz cryomodule assembly is scheduled to start in June 2019; production readiness verifications are in progress. This paper presents LCLS-II cryomodule assembly and production experience, emphasizing the challenges, the mitigations and lessons learned

Poster TUP101 [0.834 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP101

About •

paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP102

Superconducting Harmonic Cavity for Bunch Lengthening in the APS Upgrade

HOM, cryomodule, photon, operation

715

M.P. Kelly, Z.A. Conway, M. Kedzie, S.W.T. MacDonald, T. Reid, U. Wienands, G.P. Zinkann
ANL, Lemont, Illinois, USA

A superconducting cavity based Bunch Lengthening System is under construction for the Argonne’s Advanced Photon Source (APS) Upgrade. The system will reduce the undesirable effects of Touschek scattering on the beam lifetime by providing bunch lengthening in the longitudinal direction by 2-4 times. The major technical components for the beam-driven 1.4 GHz fourth harmonic superconducting cryomodule are in hand and have been tested. These include a superconducting cavity, cw rf power couplers, a pneumatic cavity slow tuner and beamline higher-order mode absorbers. Initial assembly and engineering testing of the cryomodule is underway. Final integrated testing will be complete in 2021. Transportation to and commissioning in the APS is planned for 2022-23.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP102

About •

paper received ※ 08 July 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP103

Pansophy Data as Used to Develop Metrics and Evaluate Trends Across SRF Projects and Facilities to Further Quality Improvement Initiatives

cryomodule, database, status, SRF

718

M.G. McDonald, V.D. Bookwalter, M. Dickey, E.A. McEwen
JLab, Newport News, Virginia, USA

Pansophy, a JLAB SRF engineering data management system (EDMS), is composed of a collection of technolo-gies that together provide for the collection, management and analysis of data for the production and testing of cavities and cryomodules. From its inception in 2000, when data collection was a priority for such projects as SNS, CEBAF 12GeV upgrade, LCLS-II, and in the future the SNS-PPU, the focus has turned to data analysis and reporting on quality metrics and key performance indica-tors (KPIs). Reporting enhancements include monthly quality metrics, project specific KPIs, and trending across projects. With the use of Pareto Charts to help analyze vendor quality and non-conformance, timelines of pro-ject and facility metrics, project managers and subject matter experts (SME) are able to look for trends and pre-pare further quality improvement initiatives for their projects.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP103

About •

paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP104

Improvement of a Clean Assembly Work for Superconducting RF Cryomodule and Its Application to the KEK-STF Cryomodule

cryomodule, vacuum, controls, SRF

721

H. Sakai, E. Kako, T. Konomi, K. Umemori, Y. Yamamoto
KEK, Ibaraki, Japan
T. Ebisawa, A. Kasugai
QST, Aomori, Japan

We usually encountered the degradation of the superconducting RF cavities on the cryomodule test even though the performance of these cavities was good on the vertical test. In reality, the degradation of Q-values of two cavities of cERL main-linac were observed after cryomodule assembly in KEK [1] and STF cryomodule also met the degradation after the cryomodule assembly [2]. Some dusts and invisible particles might enter the cavity and generate field emission during the assembly work. Field emission is the most important cause of this degradation. In this paper, first we introduce some trials for the improved clean assembly work to SRF cavity by re-examining our clean assembly work and vacuum work. For example, slow pumping system with vacuum particle monitor was developed to know and control the particle movement during slow pumping and venting. Next we show the application of this improved work to the STF re-assemble cryomodule work in KEK.
[1} H. Sakai et al., SRF’13, Paris, France, p.855, 2013.
[2] Y. Yamamoto et al., IPAC’16, Busan, Korea, p.2158, 2016.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP104

About •

paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP105

Preparation of the Cryomodule Assembly for the Linear IFMIF Prototype Accelerator (LIPAc) in Rokkasho

cryomodule, vacuum, operation, SRF

726

T. Ebisawa, A. Kasugai, K. Kondo, S. Maebara, K. Sakamoto
QST, Aomori, Japan
N. Bazin, S. Berry
CEA-DRF-IRFU, France
P. Cara
IFMIF/EVEDA, Rokkasho, Japan
H. Dzitko, G. Phillips
F4E, Germany
E. Kako, H. Sakai, K. Umemori
KEK, Ibaraki, Japan

The staged installation and commissioning of LIPAc is ongoing at Rokkasho Fusion Institute of QST, Japan for validating the low energy section of the IFMIF deuteron accelerator up to 9 MeV. The LIPAc Superconducting Radio Frequency accelerator (SRF) cryomodule is assembled under the responsibility of the EU Home Team, and the assembly work recently started at Rokkasho in March 2019. To fulfil the cleanliness requirements for the assembly process, QST took the responsibility to prepare the infrastructure of a cleanroom and associated devices. In this present paper, the details of the preparation work for the cryomodule assembly made by QST will be presented.

Poster TUP105 [2.116 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP105

About •

paper received ※ 17 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUP106

Mechanical Tuner for a 325 MHz Balloon Single Spoke Resonator

cryomodule, linac, simulation, operation

730

R.E. Laxdal, J.J. Keir, B. Matheson, N. Muller, Z.Y. Yao
TRIUMF, Vancouver, Canada

TRIUMF has designed, fabricated and tested the first balloon variant of the single spoke resonator at 325 MHz and β=0.3. TRIUMF has also designed and built a mechanical tuner as part of the development. The tuner employs a nutcracker lever pressing at the beam ports driven by a scissor jack. The scissor is actuated through a tube coupling to a warm ball-screw and servo-motor located outside the cryostat. The design and warm tests of the tuner will be presented.

Poster TUP106 [1.089 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-TUP106

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEA3

Status of the IFMIF/EVEDA Superconducting Linac

SRF, solenoid, cryomodule, linac

735

N. Bazin, G. Devanz, H. Jenhani, O. Piquet
CEA-DRF-IRFU, France
S. Chel
CEA-IRFU, Gif-sur-Yvette, France
T. Ebisawa
QST, Aomori, Japan
G. Phillips
F4E, Germany
D. Regidor, F. Toral
CIEMAT, Madrid, Spain

The IFMIF accelerator aims to provide an accelerator-based D-Li neutron source to produce high intensity high energy neutron flux to test samples as possible candidate materials to a full lifetime of fusion energy reactors. A prototype of the low energy part of the accelerator (LIPAc) is under construction at Rokkasho Fusion Institute in Japan. It includes one cryomodule containing 8 half-wave resonators (HWR) operating at 175 MHz and eight focusing solenoids. The talk will cover the progress of developments in the IFMIF/EVEDA cryomodule: the qualification of 8 cavities, the RF conditioning results of 8 high-power couplers, the manufacturing and test of the 8 superconducting solenoids and the equivalent operational equivalent tests performed at Saclay. The assembling status of the cryomodule at Rokkasho site will also be presented.

Slides WETEA3 [11.091 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEA3

About •

paper received ※ 20 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEA5

FRIBCavity and Cryomodule Performance, Comparison with the Design and Lessons Learned

cryomodule, alignment, solenoid, vacuum

742

S.J. Miller, H. Ao, B. Bird, B. Bullock, N.K. Bultman, F. Casagrande, C. Compton, J. Curtin, K. Elliott, A. Facco, V. Ganni, I. Grender, W. Hartung, J.D. Hulbert, S.H. Kim, P. Manwiller, E.S. Metzgar, D.G. Morris, P.N. Ostroumov, J.T. Popielarski, L. Popielarski, M.A. Reaume, K. Saito, M. Shuptar, J. Simon, B.P. Tousignant, D.R. Victory, J. Wei, J.D. Wenstrom, K. Witgen, M. Xu, T. Xu
FRIB, East Lansing, Michigan, USA
A. Facco
INFN/LNL, Legnaro (PD), Italy
M.P. Kelly
ANL, Lemont, Illinois, USA
M. Wiseman
JLab, Newport News, Virginia, USA

Funding: Work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661 and the National Science Foundation under Cooperative Agreement PHY-1102511.
The superconducting driver linac for the Facility for Rare Isotope Beams (FRIB) requires the production of 46 cryomodules. Design is complete on all six cryomodule types which utilize four superconducting radio frequency (SRF) cavity designs and superconducting solenoids. The FRIB cryomodules utilize an innovative bottom up approach to achieve alignment tolerance and simplify production assembly. The cryomodule testing includes qualification of the resonator performance, fundamental power couplers, tuners, and cryogenic systems. FRIB beam commissioning has been performed on 15 cryomodules in the FRIB and validates the FRIB cryomodule bottom up assembly and alignment method. This paper will report the FRIB cryomodule design, performance, and the alignment results and their impact on beam commissioning.

Slides WETEA5 [14.640 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEA5

About •

paper received ※ 21 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEB1

Development of Superconducting Quarter-Wave Resonator and Cryomodule for Low-Beta Ion Accelerators at RIKEN Radioactive Isotope Beam Factory

cryomodule, linac, vacuum, SRF

750

N. Sakamoto, T. Dantsuka, M. Fujimaki, H. Imao, O. Kamigaito, K. Kusaka, H. Okuno, K. Ozeki, K. Suda, A. Uchiyama, T. Watanabe, Y. Watanabe, K. Yamada
RIKEN Nishina Center, Wako, Japan
H. Hara, A. Miyamoto, K. Sennyu, T. Yanagisawa
MHI-MS, Kobe, Japan
E. Kako, H. Nakai, H. Sakai, K. Umemori
KEK, Ibaraki, Japan

A prototype cryomodule with a superconducting quarter- wave resonator (SC QWR) has been developed at RIKEN Radioactive Isotope Beam Factory (RIBF). During the last SRF conference, we presented the performance of our first SC QWR and the first cool-down test of its cryomodule. Since then, we have continued our efforts to improve cavity performance and succeeded in recovering deteriorated Q₀. In this paper, we report what we constructed and learned from the prototype, including design issues with the cavity and its cryomodule. Design issues related to the new SC QWRs and their cryomodules for the SC linac booster of the RIKEN Heavy-Ion Linac (RILAC) are described as well.

Slides WETEB1 [120.252 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEB1

About •

paper received ※ 24 June 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEB2

Identifying Specific Cryomodule and Cleanroom Particulate Contamination: Understanding Legacy Issues and Providing New Feedback Standards

cryomodule, SRF, GUI, feedback

758

C.E. Reece, J.K. Spradlin, O. Trofimova, A-M. Valente-Feliciano
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
While the techniques used to provide "UHV clean" and "particle-free" beamline components, including SRF cavities, continue to evolve, "real-world" operating machines must deal with actual accumulated and latent contamination issues that produce non-trivial cryogenic heatload, radiation, activation, and degradation via field emission. We have developed a standardized and automated particulate contamination assay method for use in characterizing particulates found on beamline components and in cleanroom assembly environments. We present results from using this system to analyze samples taken from reworked cryomodules from CEBAF. Particle sizes are much larger than anticipated. Utility for feedback on sources to enable improved source reduction is explored.

Slides WETEB2 [13.320 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEB2

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEB3

CEBAF C100 Fault Classification based on Time Domain RF Signals

cryomodule, controls, vacuum, operation

763

T. Powers, A.D. Solopova
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177
The CEBAF 12 GeV upgrade project, which was completed and commissioned in 2014, included the construction and installation of 80 new 7-cell superconducting cavities that were configured in 10 cryomodules. In 2018, the software and hardware in the digital low level RF systems were configured such that a fault would trigger an acquisition process which records waveform records of 17 of the RF signals for each of the 8 cavities within the cryomodule for subsequent analysis. These waveforms are especially useful in C100 cryomodules as there is a 10% mechanical coupling between adjacent cavities. When one cavity has a fault and the gradient is reduced quickly, it will mechanically deform due relaxation of the Lorentz force effects. This deformation change causes perturbations in the adjacent cavities which, in turn, causes a cascade of cavity faults that are difficult to understand without the time domain data. This contribution will describe the types of faults encountered during operation and their signatures in the time domain data, as well as how is being used to modify the setup of the machine and implement improvements to the cryomodules.

Slides WETEB3 [3.169 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEB3

About •

paper received ※ 21 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEB4

Virtual SRF Cavity: Testing SRF Cavity Support Systems Without the Hassle of Liquid Helium and Klystrons

controls, LLRF, FPGA, SRF

770

P. Echevarria, J. Knobloch, A. Neumann, A. Ushakov
HZB, Berlin, Germany
E. Aldekoa, J. Jugo
University of the Basque Country, Faculty of Science and Technology, Bilbao, Spain

Setting up and debugging SRF support systems, such as LLRF control, quench detection, microphonics and Lorentz-force detuning control, etc., often requires extensive time spent operating the cavities. This results in time consuming and costly operation. Early into the development stages the actual cavity system may not even be available. It is therefore highly desirable to pre-evaluate these systems under realistic conditions prior to final testing with the SRF cavities. We devised an FPGA-based "virtual cavity" that takes a regular low-level RF input and generates the signals for RF-power reflection, transmission and detuning that mimic the response of a real cavity system. As far as the user is concerned, the response is the same as for a real cavity. This "black-box" model includes mechanical modes, Lorentz force detuning, a field depended quality factor, quenches and variable input coupling and is currently being expanded. We present the model and show some applications for operating the quench detection, LLRF and microphonics control for 1.3 GHz BERLinPro cavities. The same system can be used for other cavity types, including normal conducting cavities.

Slides WETEB4 [9.784 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEB4

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEB6

Active Suppression of Microphonics Detuning in High QL Cavities

controls, linac, resonance, SRF

776

N. Banerjee, G.H. Hoffstaetter, M. Liepe, P. Quigley
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA

Funding: This work was performed through the support of New York State Energy Research and Development Agency (NYSERDA). SRF 2019 provided travel support in the form of a student grant.
Accelerators operating with low beam loading such as Energy Recovery Linacs (ERL) greatly benefit from using SRF cavities operated at high loaded quality factors, since it leads to lower RF power requirements. However, large microphonics detuning several times the operating bandwidth of the cavities severely limit the maximum accelerating fields which can be sustained in a stable manner. In this talk, I will describe an active microphonics control technique based on the narrow band Active noise Control (ANC) algorithm which we have used in CBETA, a multi-turn SRF ERL being commissioned at Cornell University. I will describe its stability and performance during beam operations of CBETA with consistent reduction of peak detuning by almost a factor of 2 on multiple cavities.

Slides WETEB6 [10.296 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEB6

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEB7

A Ferroelectric Fast Reactive Tuner for Superconducting Cavities

controls, linac, experiment, superconducting-cavity

781

N.C. Shipman, J. Bastard, M.R. Coly, F. Gerigk, A. Macpherson, N. Stapley
CERN, Geneva, Switzerland
I. Ben-Zvi
BNL, Upton, New York, USA
G. Burt, A. Castilla
Lancaster University, Lancaster, United Kingdom
C.-J. Jing, A. Kanareykin
Euclid TechLabs, LLC, Solon, Ohio, USA
S. Kazakov
Fermilab, Batavia, Illinois, USA
E. Nenasheva
Ceramics Ltd., St. Petersburg, Russia

A prototype FerroElectric Fast Reactive Tuner (FE-FRT) for superconducting cavities has been developed, which allows the frequency to be controlled by application of a potential difference across a ferroelectric residing within the tuner. This technique has now become practically feasible due to the recent development of a new extremely low loss ferroelectric material. In a world first, CERN has tested the prototype FE-FRT with a superconducting cavity, and frequency tuning has been successfully demonstrated. This is a significant first step in the development of an entirely new class of tuner. These will allow electronic control of cavity frequencies, by a device operating at room temperature, within timescales that will allow active compensation of microphonics. For many applications this could eliminate the need to use over-coupled fundamental power couplers, thus significantly reducing RF amplifier power.

Slides WETEB7 [21.570 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEB7

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEB8

The Fundamental Power Coupler for CEPC Booster Cavity

vacuum, booster, simulation, multipactoring

789

T.M. Huang, F. Bing, R. Guo, H.Y. Lin, Q. Ma, W.M. Pan, J.Y. Zhai, Z. Zhang
IHEP, Beijing, People’s Republic of China

Funding: Supported by National natural Science Foundation of China ( 11475203)
96 Tesla type 1.3GHz 9-cell superconducting cavities, housed in eight 12m-long cryomodules, will be adopted for CEPC booster. Each cavity equips with one variable coupling, double-window fundamental power coupler (FPC). The FPC will operate at RF power up to 20 kW at quasi-CW mode. A variable coupling from 4·10⁶ to 10⁷ is required to meet different operation modes of Higgs, W and Z. A new coupler that employs a 50 Ω coaxial line with bellow structures, a cylindrical warm window, a coaxial planar cold window and a coupling adjusting actuator has been designed. Then two prototypes have been fabricated and high power tested up to CW 70 kW successfully. In this paper, the design, fabrication and high power test of the prototype FPCs will be presented.

Slides WETEB8 [9.971 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEB8

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WETEB9

Design Development for the 1.5 GHz Couplers for BESSY VSR

operation, coupling, diagnostics, GUI

795

E. Sharples, M. Dirsat, J. Knobloch, Z. Muza, A.V. Vélez
HZB, Berlin, Germany

The Variable pulse length Storage Ring (BESSY VSR) is a superconducting radio frequency (SRF) upgrade to the existing BESSY II storage ring at Helmholtz-Zentrum Berlin (HZB). BESSY VSR uses the RF beating of superconducting cavities at 1.5 GHz and 1.75 GHz to produce simultaneously long and short bunches. Higher power couplers capable of handling 13 kW peak power at standing wave operation, are required to provide an average power of 1.5 kW for both the 1.5 GHz and 1.75 GHz cavities. These couplers must also provide variable coupling with a range of Q_ext from 6x10⁶ to 6x10⁷ to allow flexibility to adjust to operating conditions of BESSY VSR. Here the full design development process for the 1.5 GHZ BESSY VSR coupler is presented including the design for a diagnostic prototype to ensure comprehensive monitoring of critical components during testing and cool-down.

Slides WETEB9 [8.085 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-WETEB9

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THFUA1

RF Characterization of an S-I-S’ Multilayer Sample

niobium, quadrupole, ECR, SRF

800

S. Keckert, J. Knobloch, O. Kugeler, D.B. Tikhonov
HZB, Berlin, Germany
A-M. Valente-Feliciano
JLab, Newport News, Virginia, USA

S-I-S’ multilayers promise to boost the performance of bulk superconductors in terms of maximum field and surface resistance. At HZB, RF-surface resistance measurements were performed with a Quadrupole Resonator (QPR) and an S-I-S’ sample (75 nm NbTiN on 15 nm AlN insulator on bulk Nb) prepared at JLab. Measurements were performed at 414, 845, and 1286 MHz at sample temperatures from 2 K up to well above the transition temperature of NbTiN of ~17.3 K. The Rs exhibits an unexpected temperature dependence: Rather than rising monotonically, as expected from BCS theory, a local maximum is observed. There is a temperature range where Rs decreases with increasing temperature. Such behavior indicates that an additional interaction between the superconducting layers may have to be included in the surface resistance model. Measurements of the baseline Nb sample prior to coating exhibited no such behavior; hence systematic measurement errors can be excluded as the explanation. The maximum field was limited by a hard magnetic quench near 20 mT, close to Hc1 of NbTiN, suggesting that the sample is limited by early flux penetration.

Slides THFUA1 [1.004 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THFUA1

About •

paper received ※ 22 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THFUA6

Nb₃Sn Films for SRF Cavities: Genesis and RF Properties

niobium, SRF, interface, experiment

810

U. Pudasaini, M.J. Kelley
The College of William and Mary, Williamsburg, Virginia, USA
J.W. Angle, M.J. Kelley, J. Tuggle
Virginia Polytechnic Institute and State University, Blacksburg, USA
G.V. Eremeev, M.J. Kelley, C.E. Reece
JLab, Newport News, Virginia, USA

Funding: Partially authored by Jefferson Science Associates under contract no. DE¬AC05¬06OR23177. Supported by Office of High Energy Physics under grants DE-SC-0014475 to the College of William and DE-SC-0018918 to Virginia Tech.
Understanding of Nb₃Sn nucleation and growth is essential to the progress with Nb₃Sn vapor diffusion coatings of SRF cavities. Samples representing different stages of Nb₃Sn formation have been produced and examined to elucidate the effects of nucleation, growth, process conditions, and impurities. Nb₃Sn films from few hundreds of nm up to ~15 µm were grown and characterized using AFM, SEM/EDS, XPS, EBSD, SIMS, and SAM. Microscopic examinations of samples suggest the mechanisms behind Nb₃Sn thin film nucleation and growth. RF measurements of coated cavities were combined with material characterization of witness samples to adapt the coating process in "Siemens" coating configuration. Understanding obtained from sample studies, applied to cavities, resulted in Nb₃Sn cavity with quality factor 2 ×10¹⁰ at 15 MV/m accelerating gradient at 4 K, without "Wuppertal" Q-slope. We discuss the genesis of the Nb₃Sn thin film in a typical tin vapor diffusion process, and its consequences to the coating of SRF cavities.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THFUA6

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THFUB1

Nb₃Sn at Fermilab: Exploring Performance

SRF, multipactoring, niobium, superconductivity

818

S. Posen, J. Lee, O.S. Melnychuk, Y.M. Pischalnikov, D.A. Sergatskov, B. Tennis
Fermilab, Batavia, Illinois, USA
J. Lee, D.N. Seidman
NU, Evanston, Illinois, USA

Fermilab’s Nb₃Sn coating program produced its first 1.3 GHz single cell cavities in early 2017 and since then has explored the performance of Nb₃Sn on a wide variety of cavity substrates and performed microscopic studies down to atomic resolution. Results to present in this talk include a study of frequency dependence from 650 MHz to 1.3 GHz of BCS resistance, residual resistance, and magnetic flux sensitivity. We show microscopic studies performed in collaboration with Northwestern University¿s Materials Science and Engineering Department of limitation mechanisms in Nb₃Sn, including thin film regions and tin segregation at grain boundaries, discussing correlations with RF performance and mechanisms for the formation of these features during growth. Finally, we present results of the first 1.3 GHz 9-cell cavity coated with Nb₃Sn.

Slides THFUB1 [27.194 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THFUB1

About •

paper received ※ 29 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THFUB2

Progress with Nb Hipims Films on 1.3 GHz Cu Cavities

SRF, lattice, cathode, superconductivity

823

M.C. Burton, A.D. Palczewski, C.E. Reece, A-M. Valente-Feliciano
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
In recent years, efforts have been invested to leverage the different processes involved in energetic condensation to tailor Nb film growth in sequential steps. The resulting Nb/Cu films display high quality material properties and show promise of high RF performance. The lessons learned are now applied to 1.3 GHz Nb on Cu cavity deposition via high power impulse magnetron sputtering (HiPIMS). RF performance is measured at different temperatures. Particular attention is given to the effect of cooldown and sensitivity to external applied magnetic fields. The results are evaluated in light of the Nb film material and superconducting properties measured with various microscopy and magnetometry techniques in order to better understand the contributing factors to the residual and flux induced surface resistances. This contribution presents the insights gained in exploiting energetic condensation as a path towards RF Q-slope mitigation for Nb/Cu films, correlating film material characteristics with RF performance.

Slides THFUB2 [7.869 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THFUB2

About •

paper received ※ 02 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP002

Metallographic Polishing Pathway to the Future of Large Scale SRF Facilities

SRF, niobium, embedded, cryogenics

828

O. Hryhorenko, M. Chabot
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France
C.Z. Antoine
CEA-IRFU, Gif-sur-Yvette, France
D. Longuevergne
FLUO, Orsay, France

Funding: The financial support from the European Nuclear Science and Applications Research 2 (ENSAR 2) under grant agreeement N°654002.
Optimization of SRF cavities mainly focuses on pushing the limits of bulk Niobium, cost reduction of cavity fabrication and development of new SRF materials for future accelerators (ILC, FCC). Nowadays chemical etching is the only surface treatment used to prepare SRF surface made of Nb. However the operational cost of chemical facilities is high and these present a very bad ecological footprint. The search of an alternative technique could make the construction of these future large scale facilities possible. Metallographic polishing (MP) is a candidate not only for bulk Nb treatment, but could also provide the mirror-finished substrate for alternative SRF thin films deposition. Recent R&D studies, conducted at IPNO & IRFU, focused on the development of 2-steps MP procedure of Nb flat samples. Roughness of polished surface has been proven better than standard EP treatment and less polluted than CBP. MP provides on flat surfaces a high removal rate (above 1 µm/min) and high reproducibility. The paper will describe the optimized method and present all the surface analysis performed. The first RF characterization of a polished disk will be presented.

Poster THP002 [2.902 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP002

About •

paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP003

Results on Bulk Niobium Surface Resistance Measurement With Pillbox Cavity on TE011 and TE012 Modes

niobium, coupling, SRF, experiment

833

G. Martinet
Université Paris-Saclay, CNRS/IN2P3, IJCLab, Orsay, France

Surface measurement of superconducting samples is required to characterize processes of bulk niobium preparation for SRF resonators. In order to reduce characterization cost and improve measurement performances, a pill-box cavity has been developed at IPN Orsay. Using TE011 and TE012 modes, we describe the latest results based on calorimetric method.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP003

About •

paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP004

Design and Fabrication of a Quadrupole-Resonator for Sample R&D

quadrupole, SRF, simulation, niobium

838

R. Monroy-Villa, D. Reschke, M. Wenskat
DESY, Hamburg, Germany
W. Hillert, R. Monroy-Villa, M. Wenskat
University of Hamburg, Institut für Experimentalphysik, Hamburg, Germany
S. Keckert, O. Kugeler, D.B. Tikhonov
HZB, Berlin, Germany
P. Putek, S.G. Zadeh, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
U. van Rienen
University of Rostock, Rostock, Germany

Being able to obtain BCS and material properties from the same surface is necessary to gain a fundamental understanding of the evolution of SRF surfaces. A test resonator which will allow to obtain BCS properties from samples is currently under development at the University of Hamburg and DESY and is based on the Quadrupole Resonators developed and operated at CERN and HZB. The current status of the necessary infrastructure, the procurement process and design considerations are shown. In addition, an outline of the planed R&D project with the Quadrupole Resonator will be presented and first RF measurements and surface analysis results of samples will be shown

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP004

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP007

In-Situ EXAFS Investigations of Nb-Treatments in N₂ at Elevated Temperatures

experiment, niobium, vacuum, lattice

842

P. Rothweiler, B. Bornmann, J. Klaes, D. Lützenkirchen-Hecht, R. Wagner, S. von Polheim
University of Wuppertal, Wuppertal, Germany

Funding: We gratefully acknowledge financial support by the German Federal Ministry of Education and Research (BMBF) under project No. 05H15PXRB1.
Smooth polycrystalline Nb metal foils were exposed to dilute N₂ and Kr atmospheres at elevated temperatures of up to 900°C. Transmission mode X-ray absorption spectroscopy (EXAFS) experiments were used to study the resulting changes of the atomic short range order structure in-situ. EXAFS data were collected prior to any heat treatment as well as during the different process steps at elevated temperatures with a time resolution of about 1 s, and the samples were also studied after cooling to room temperature. In general, only very small changes of the Nb-EXAFS data could be detected after the processing in N₂-atmospheres, and no evidence for bulk formation of Nb-nitrides was found. In contrast, the quantitative EXAFS data evaluation revealed slightly distorted Nb-Nb coordinations, suggesting that N-atoms are increasingly incorporated on octahedral interstitial sites in the host lattice with increasing N₂-exposure. For the treatments in Kr-atmospheres, simultaneous measurements are feasible at both the K-edge of the Nb host and the Kr dopant. Those studies gave clear evidence for a Kr uptake during the heat treatment, and will be discussed in more detail at the conference.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP007

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP008

The Technical Study of Nb₃Sn Film Deposition on Copper by HiPIMS

SRF, niobium, electron, superconductivity

846

L. Xiao, X.Y. Lu, W.W. Tan, D. Xie, Y. Yang, L. Zhu
PKU, Beijing, People’s Republic of China

Our work is mainly focused on the deposition methods of Nb₃Sn films on Cu substrates and film‘s properties. The superconducting transition temperature(Tc) of Nb₃Sn film is 12K. There are diffraction peaks of Nb₃Sn in the X-ray diffraction patterns in which without diffraction peaks of copper compounds. Scanning electron micro-structures of Nb₃Sn film reflect its nice compactness and binding force between film and substrate.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP008

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP009

Pulse Laser Annealing of Niobium Film on Copper for SRF Cavities

laser, niobium, experiment, interface

848

Y. Yang, X.Y. Lu, W.W. Tan, L. Xiao, D. Xie, L. Zhu
PKU, Beijing, People’s Republic of China

Thin film cavities were proposed as the most promis-ing next generation superconducting cavities. The chal-lenges are improving the surface superconducting per-formance and reducing defects of the coating film, which can be greatly solved by laser annealing. Laser annealing system has been set up in Peking University, and experi-ments with niobium thin film sample have been carried out. Superconducting performance and other properties of Nb/Cu samples before and after annealing were com-pared. Recrystallization happened and surface structure improved a lot according to the results.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP009

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP010

The Mechanism of Electropolishing of Niobium from Choline Chloride-based Deep Eutectic Solvents

ECR, polarization, impedance, niobium

852

Q.W. Chu, H. Guo, S.C. Huang, A.D. Wu, Z.M. You
IMP/CAS, Lanzhou, People’s Republic of China

Funding: National Natural Science Foundation (11705252)
The mechanism of electropolishing of niobium (Nb) from choline chloride-based deep eutectic solvent (DES) was studied by anodic polarization tests and electrochemical impedance spectroscopy (EIS) using a Nb rotating disk electrode (RDE). Based on the results of an anodic polarisation test, the electropolishing of Nb is mass transport controlled. EIS results are consistent with the compact salt film mechanism for niobium electropolishing in this electrolyte. The influence of rotation rate, applied potential and electrolyte temperature on the electropolishing mechanism of Nb was investigated. As the applied potential positively shift, Rct, Rp and L increase, CPE decrease and Rs unchanged. The increase in rotation rate and electrolyte temperature leads to a decrease of Rs, Rct, Rp and L, and an increase of CPE.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP010

About •

paper received ※ 18 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP011

Niobium Semiproducts for the Superconducting Strands and SRF Cavities in Russia

niobium, ECR, SRF, target

857

M.V. Alekseev, I.M. Abdyukhanov, V.A. Drobyshev, M.V. Kravtsova, M.V. Krylova, P.A. Lykianov, K.A. Mareev, V.I. Pantsyrny, M.V. Polikarpova, M.M. Potapenko, A.G. Silaev, A.S. Tsapleva
SC A A Bochvar High-Technology Research Institute of Inorganic Materials, Moscow, Russia
M.Y. Shlyakhov, S.M. Zernov
JSC - TVEL, Moscow, Russia

The melting regimes of the niobium ingots with high chemical purity and low hardness for the Nb₃Sn, NbTi and other superconducting materials manufacture have been developed at SC "VNIINM". Using this niobium material and by the SC "VNIINM" manufacture regimes at the SC "Chepetsky Mechanical Plant" 220 tons of Nb₃Sn and NbTi strands for ITER and 12 km of Nb₃Sn strands for HL-LHC (CERN) with the required characteristics have been successfully produced. The review of the characteristics of the different semiproducts (sheets, tubes, rods), made in Russia from the special grade niobium, and of the superconducting strands, manufactured with the use of them, is presented in the paper. The ways of the further improvement of the niobium ingots melting regimes and niobium sheets deformation and annealing regimes with the target of achieving RRR > 300 for the SRF cavities application are discussed.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP011

About •

paper received ※ 23 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP012

Assessment of the Mechanical Properties of Ultra-High Purity Niobium After Cold Work and Heat Treatment With the HL-LHC Crab Cavities as Benchmark

ECR, operation, niobium, simulation

860

A. Gallifa Terricabras, A. Amorim Carvalho, I. Aviles Santillana, S. Barrière, R. Calaga, E. Cano-Pleite, O. Capatina, M.D. Crouvizier, L. Dassa, M.S. Meyer, N. Valverde Alonso
CERN, Geneva, Switzerland
M. Benke, A.B. Palotas, G. Szabó, M. Szűcs
University of Miskolc, Faculty of Materials Science and Engineering, Miskolc-Egyetemváros, Hungary
A. Hlavács, G.J. Krallics, V. Mertinger, M. Sepsi
University of Miskolc, Miskolc, Hungary

The High Luminosity Large Hadron Collider (HL-LHC) is the upgrade of the world’s largest particle collider; it will allow the full exploitation of the LHC potential and its operation beyond 2025. An essential part of the HL-LHC project are the Crab Cavities, that are particle deflecting SRF cavities of non-axisymmetric shape made of bulk ultra-high purity Nb. Since the cavities are produced by complex metal sheet forming processes, followed by a heat treatment (HT) for H outgassing (650 °C, 24 h), there is uncertainty on their mechanical properties after manufacturing and in service conditions (2 K). Mechanical tests at room temperature have been conducted on RRR300 pure Nb samples. The samples were previously submitted, by cold cross-rolling, to different levels of plastic deformation representative of the effective plastic strain seen by the Nb sheets during forming operations. Moreover, a comparison of the mechanical properties of cold cross-rolled samples before and after HT has been established. Results of evolution of the microstructure and hardness are also presented. This study can be of interest for Nb cavities to be sub-mitted to HT at 650 °C, and may help to push the design of novel SRF cavities.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP012

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP014

First Direct Imaging and Profiling TOF-SIMS Studies on Cutouts from Cavities Prepared by State-of-the-Art Treatments

niobium, SRF, GUI, superconductivity

866

A.S. Romanenko, A. Grassellino, M. Martinello, Y. Trenikhina
Fermilab, Batavia, Illinois, USA
D. Bafia
Illinois Institute of Technology, Chicago, Illinois, USA

Funding: This work has been authored by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the U.S. Department of Energy, Office of Science, Office of High Energy Physics.
Small amounts of interstitial impurities in the penetra-tion depth of superconducting radio frequency (SRF) cavities have a dramatic effect on the quality factors and maximum accelerating gradients. Here we report the first TOF-SIMS studies of cutouts from cavities prepared by all modern surface treatments, which allow a direct corre-lation of the impurity distribution with the observed cavity performance. Imaging capability of our instrument allows to avoid the possible issues associated with the ‘‘ghost’’ depth profiles appearing as a consequence of particulate surface contamination, which likely caused the inconclusive SIMS results on e.g. oxygen diffusion in the past.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP014

About •

paper received ※ 02 July 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP017

Crystallographic Characterization of Nb₃Sn Coatings and N-Doped Niobium via EBSD and SIMS

niobium, interface, SRF, electron

871

J.W. Angle, M.J. Kelley, J. Tuggle
Virginia Polytechnic Institute and State University, Blacksburg, USA
G.V. Eremeev, M.J. Kelley, C.E. Reece
JLab, Newport News, Virginia, USA
M.J. Kelley, U. Pudasaini
The College of William and Mary, Williamsburg, Virginia, USA

Historically, niobium has been used as the superconducting material in SRF cavities. Due the high operational costs, other materials are currently being considered. Nb₃Sn coatings have been investigated over the past several decades, motivated by potentially higher operating temperatures. More recently niobium has been doped with nitrogen to improve the quality factor (Q). Currently, a need for better understanding still exists for both mechanisms. EBSD has been shown to be a viable technique to determine the crystallographic orientation and the size of the Nb₃Sn grains. The EBSD maps obtained show a bimodal distribution of grain sizes with smaller Nb₃Sn grains found present near the Nb₃Sn/Nb interface. In addition to the Nb₃Sn coatings, N-doped niobium coupons were analyzed by EBSD and found that the coupon had preferred surface orientation. The EBSD analysis was found to be vital as specific grains could be targeted in SIMS to better understand the diffusion of nitrogen with respect to crystal orientation.

Poster THP017 [2.571 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP017

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP020

Study of Dislocation Content Near Grain Boundaries using Electron Channeling Contrast Imaging and its Effect on Superconducting Properties of Niobium

electron, SRF, niobium, superconductivity

876

M. Wang, T.R. Bieler
Michigan State University, East Lansing, Michigan, USA
S. Balachandran, S. Chetri, P.J. Lee
NHMFL, Tallahassee, Florida, USA
S. Chetri, A. Polyanskii
ASC, Tallahassee, Florida, USA
C. Compton, C. Compton
FRIB, East Lansing, Michigan, USA
C. Compton
NSCL, East Lansing, Michigan, USA

Funding: U.S. Department of Energy. National Science Foundation Cooperative Agreement No. DMR-1157490 (-2017) DMR-1644779 (2018-) and the State of Florida
Trapped micro-Tesla levels of magnetic flux degrade the performance of Nb superconducting radio frequency (SRF) accelerators. Recent studies have revisited the role of small deformation (dislocation substructure influence) on cavity performance. However, the link between microstructural defects and mechanisms leading to poor performance is still unresolved. To examine the mechanism of flux pinning by dislocations and grain boundaries, systematic studies on bi-crystal Nb tensile samples were designed with strategically chosen orientation relationships between neighboring crystals with respect to the grain boundaries. Laue X-ray diffraction and electron backscatter diffraction analysis was used to measure crystal orientations of a large-grain Nb slice, from which the bi-crystals were extracted. Dislocation structures near the grain boundaries were characterized before and after 5% tensile deformation using electron channeling contrast imaging (ECCI), after which the magnetic flux behavior was observed using cryogenic magneto-optical imaging (MOI). We discuss the conditions under which we observe increased flux pinning in regions of high dislocation density.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP020

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP023

RF Commissioning of the CBETA Main Linac Cryomodule

operation, linac, LLRF, controls

881

N. Banerjee, J. Dobbins, G.H. Hoffstaetter, R.P.K. Kaplan, M. Liepe, C.W. Miller, P. Quigley, E.N. Smith, V. Veshcherevich
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA

Funding: This work was performed through the support of New York State Energy Research and Development Agency (NYSERDA).
The Cornell BNL ERL Test Accelerator (CBETA) employs a superconducting Main Linac Cryomodule in order to perform multi-turn energy recovery operation. Optimizing the field stability of the low bandwidth SRF cavities in the presence of microphonics with limited available RF power is a challenging task. Despite of this, the Main Linac Cryomodule has been successfully used in CBETA to impart a maximum energy gain of 54 MeV, well above the energy gain requirement of CBETA. In this paper, we present an overview of our RF commissioning procedure including automatic coarse tuning, measurement of DAC and phase offsets. We further detail our microphonics measurements from our most recent run period.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP023

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP025

Overview of Superconducting RF Cavity Reliability at Diamond Light Source

vacuum, operation, GUI, storage-ring

885

C. Christou, P. Gu, P.J. Marten, S.A. Pande, A.F. Rankin, D. Spink, L.T. Stant, A. Tropp
DLS, Oxfordshire, United Kingdom

Diamond Light Source has been providing beam for users since January 2007. The electron beam in the storage ring is normally driven by two superconducting CESR-B cavities, with two similar cavities available as spares. Day-to-day reliability of the cavities, measured by storage ring MTBF, has improved enormously over the years. A full analysis of how this improvement has been achieved is given, with particular attention paid to cavity voltage and vacuum pressure management, and the scheduling and procedure of cavity conditioning. The benefits and risks of full and partial warm-ups of the cavities are discussed, and details and impacts of cavity failure and repair are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP025

About •

paper received ※ 21 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP026

Initial Operation of the LCLS-II Electron Source

gun, vacuum, cathode, operation

891

C. Adolphsen, A.L. Benwell, G.W. Brown, M.P. Dunning, S. Gilevich, K. Grouev, X. Liu, J.F. Schmerge, T. Vecchione, F.Y. Wang, F. Zhou
SLAC, Menlo Park, California, USA
G. Huang, M.J. Johnson, T.H. Luo, F. Sannibale, S.P. Virostek
LBNL, Berkeley, California, USA

Funding: This work supported under DOE Contract DE-AC02-76SF00515
The Early Injector Commissioning program for LCLS-II aims to demonstrate CW electron beam production this year in the first two meters of the injector that includes the room-temperature 185.7 MHz single-cell gun and the 1.3 GHz two-cell buncher cavity. These cavities were designed and built by LBNL based on their experience with similar ones for their Advanced Photo-Injector Experiment (APEX) program. With the 258 nm laser system and Cs2Te cathodes, bunches of up to 300 pC are expected at rates as high as 1 MHz. The paper presents results from this program including the vacuum levels achieved, RF processing and field control experience, dark current measurements and laser and beam characterization.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP026

About •

paper received ※ 26 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP027

Cryogenics Performance of the Vertical Cryostat for Qualifying ESS-SRF High Beta Cavities

SRF, cryogenics, operation, MMI

895

S.M. Pattalwar, R.K. Buckley, P.C. Hornickel, K.J. Middleman, M.D. Pendleton, P. Pizzol, P.A. Smith, T.M. Weston, A.E. Wheelhouse, S. Wilde
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
A.J. May, A. Oates, J.T.G. Wilson
STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom

An innovative vertical cryostat has been developed and commissioned at STFC Daresbury Laboratory for qualifying the high-beta SRF cavities for the ESS (European Spallation Source). The cryostat is designed to test 3 dressed cavities in horizontal configuration in one cold run at 2K. The cavities are cooled to 2K with superfluid liquid helium filled into individual helium jackets of the cavities. This reduces the liquid helium consumption by more than 70% in comparison with the conventional vertical tests. The paper describes the cryogenic system and its performance with detail discussions on the initial results.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP027

About •

paper received ※ 22 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP028

Superconducting RF Modules of TARLA

cryomodule, electron, rf-amplifier, MMI

900

Ç. Kaya, Ö. Karslı, İ.B. Koç
Ankara University, Accelerator Technologies Institute, Golbasi, Turkey
A. Aksoy, O.F. Elçim
Ankara University Institute of Accelerator Technologies, Golbasi, Turkey

The Turkish Accelerator and Radiation Laboratory (TARLA) is proposed as an accelerator-based radiation source facility to provide a research instrument for researchers from both Turkey and region. The facility is located at the Ankara University Institute of Accelerator Technologies and proposed as the first accelerator based research infrastructure in Turkey. The superconducting accelerator of TARLA is currently under commissioning and will drive two Free Electron Laser (FEL) lines in the mid- and far-infrared ranges and a high flux Bremsstrahlung radiation to 40 MeV electron beam in Continuous Wave (CW) mode. The SRF cryomodules have been delivered by industry in 2017. In this paper, we present the achieved vertical test results of the SRF cavities, the results of the high power RF test of the fundamental power couplers and the first test results of the integrated piezo tuner. After the successful commissioning of the cryogenic plant operating at 1.8 K with ±0.2 mbar pressure stability, the commissioning of the SRF cryomodules is now ongoing and the current status and results achieved so far are explained.

Poster THP028 [1.996 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP028

About •

paper received ※ 28 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP031

Operation Experience with the LHC ACS RF System

cryomodule, operation, injection, MMI

911

K. Turaj, L. Arnaudon, P. Baudrenghien, O. Brunner, A.C. Butterworth, F. Gerigk, M. Karppinen, P. Maesen, E. Montesinos, F. Peauger, G.J. Rosaz, E.N. Shaposhnikova, D. Smekens, M. Taborelli, M. Therasse, H. Timko, D. Valuch, N. Valverde Alonso, W. Venturini Delsolaro
CERN, Meyrin, Switzerland

The LHC accelerating RF system consists of two cryomodules per beam, each containing four single-cell niobium sputtered 400.8 MHz superconducting cavities working at 4.5 K and an average accelerating voltage of 2 MV. The paper summarises the experience, availability and evolution of the system within 10 years of operation. The lessons learned from the successful replacement and re-commissioning of one cryomodule with a spare module, and the recent re-test of the originally installed module on the test stand are also included. Finally, a review of currently launched spare cavity production and long-term developments are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP031

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP033

Cryogenic Systems Studies for the MINERVA 100 MeV Proton SC LINAC Project

cryogenics, linac, cryomodule, proton

918

O. Kochebina, F. Dieudegard, T. Junquera
Accelerators and Cryogenic Systems, Orsay, France
D. Vandeplassche
SCK•CEN, Mol, Belgium

The construction of the first phase of the MYRRHA project (MINERVA: 100 MeV-4 mA proton Linac) was recently decided by the Belgium Government. In the long term, the MYRRHA project plans to construct an ADS demonstrator for the transmutation of long-lived radioactive waste. It will include a subcritical reactor of 100 MW thermal power and a CW proton Linac accelerator (600 MeV-4 mA). The main challenge of this Linac is an extremely high reliability performance to limit stresses and long restart procedures of the reactor. The MINERVA Linac includes 30 cryomodules housing 60 Single-Spoke SC cavities. A cryomodule prototype with its valve box is under construction at IPNO institute. The cavities operate at 352 MHz in a superfluid Helium bath at 2K. Therefore, a reliable SC Linac Cryogenic System is essential. This article presents the preliminary studies in this subject including the analysis of high thermal loads induced by the CW mode operation of cavities (950 W@2 K per cryomodule). A Cryogenic Refrigerator with an equivalent power capacity of 2645 W @4.5 K (3970 W with 1.5 overcapacity factor) is proposed. The constrains for the He distribution in the Linac tunnel are also discussed.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP033

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP035

Design of LHC Crab Cavities Based on DQW Cryomodule Test Experience

pick-up, coupling, HOM, controls

925

S. Verdú-Andrés
BNL, Upton, New York, USA
R. Calaga, E. Cano-Pleite, R. Leuxe
CERN, Geneva, Switzerland
J.A. Mitchell
Lancaster University, Lancaster, United Kingdom

Funding: Work supported by US DOE through Brookhaven Science Associates LLC under contract No. DE-SC0012704, contract No. DE-FOA-0001848 and by the European Union HL-LHC Project.
A cryomodule with two Double-Quarter Wave (DQW) cavities was designed, built and tested with the SPS beam in 2018. Each cavity was equipped with an rf pickup antenna to monitor field amplitude and phase. The pickup antenna also included a section expressly designed to couple and extract one of the Higher-Order Modes (HOM) at 1.754 GHz. The SPS beam tests evidenced direct coupling of the beam to this pickup antenna, in a similar way that a beam position monitor pickup couples to the passing beam. This undesired coupling had an impact on the RF feedback system responsible to regulate the cavity field and frequency. The present paper proposes a new DQW cavity design with improved antennae which provides adequate fundamental mode extraction while providing a reduction of both direct coupling to the beam and heat dissipation.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP035

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP036

An Insight on the Thermal and Mechanical Numerical Evaluations for the High-Luminosity LHC Crab Cavities

pick-up, coupling, electromagnetic-fields, experiment

929

E. Cano-Pleite, A. Amorim Carvalho, K. Artoos, R. Calaga, O. Capatina, T. Capelli, F. Carra, L. Dassa, M. Garlasché, R. Leuxe, E. Montesinos
CERN, Geneva, Switzerland
J.A. Mitchell
Lancaster University, Lancaster, United Kingdom
S. Verdú-Andrés
BNL, Upton, New York, USA

Funding: Research supported by the HL-LHC project
One of the key devices of the HL-LHC project are SRF crab cavities. A cryomodule with two Double Quarter Wave (DQW) crab cavities has been successfully fabricat-ed and tested with beam at CERN whereas the Radio Frequency Dipole (RFD) crab cavities are currently on its fabrication process. The paper provides an insight on the multiple calculations carried out to evaluate the thermal and mechanical performance of the DQW and RFD cavi-ties and its components. In some cases, the presence of RF fields inside the cavity volume requires the use of mul-tiphysics numerical models capable of coupling these fields with the thermal and mechanical domains. In fact, the RF field presents a strong dependency on the cavity shape, whereas the mechanical, thermal and electrical properties of the materials may substantially vary as a function of temperature, which in turn depends on the RF field. The results presented in this paper, using both cou-pled and uncoupled models, allowed elucidating the importance of physics coupling on the numerical evalua-tion of RF cavities and its components. Analyses were also of great support for the design evaluation and im-provement of future prototypes.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP036

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP041

Impact of the Cu Substrate Surface Preparation on the Morphological, Superconductive and RF Properties of the Nb Superconductive Coatings

laser, SRF, radiation, niobium

935

C. Pira, E. Chyhyrynets
INFN/LNL, Legnaro (PD), Italy
C.Z. Antoine
CEA-IRFU, Gif-sur-Yvette, France
X. Jiang, S.B. Leith, M. Vogel
University Siegen, Siegen, Germany
A. Katasevs, J. Kaupužs, A. Medvids, P. Onufrijevs
Riga Technical University, Riga, Latvia
O. Kugeler
HZB, Berlin, Germany
O.B. Malyshev, R. Valizadeh
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
R. Ries, E. Seiler
Slovak Academy of Sciences, Institute of Electrical Engineering, Bratislava, Slovak Republic
A. Sublet
CERN, Meyrin, Switzerland

Funding: This project has received funding from the European Union’s Horizon 2020 Research and Innovation programme under Grant Agreement No 730871.
Nowadays, one of the main issues of the superconducting thin film resonant cavities is the Cu surface preparation. A better understanding of the impact of copper surface preparation on the morphological, superconductive (SC) and RF properties of the coating, is mandatory in order to improve the performances of superconducting cavities by coating techniques. ARIES H₂020 collaboration includes a specific work package (WP15) to study the influence of Cu surface polishing on the SRF performances of Nb coatings that involves a team of 8 research groups from 7 different countries. In the present work, a comparison of 4 different polishing processes for Cu (Tumbling, EP, SUBU, EP+SUBU) is presented through the evaluation of the SC and morphological properties of Nb thin film coated on Cu planar samples and QPR samples, polished with different procedures. Effects of laser annealing on Nb thin films have also been studied. Different surface characterizations have been applied: roughness measurements, SEM, EDS, XRD, AFM, and thermal and photo-stimulated exoelectrons measurements. SC properties were evaluated with PPMS, and QPR measurements will be carry out at HZB in the beginning of 2019.

Poster THP041 [3.196 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP041

About •

paper received ※ 23 June 2019 paper accepted ※ 05 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP042

Initial Results from Investigations into Different Surface Peparation Techniques of OFHC Copper for SRF Applications

site, experiment, ECR, SRF

941

S.B. Leith, X. Jiang, Z. Khalil, A.S.H. Mohamed, M. Vogel
University Siegen, Siegen, Germany

Funding: This work forms part of the EASITrain research programme. This Marie Sklodowska-Curie Action (MSCA) Innovative Training Networks (ITN) has received funding from the European Union¿s H₂020 Framework Programme under Grant Agreement no. 764879
As part of efforts to improve the performance of thin film coated accelerating cavities, improvement of the topography of the surface of copper is being pursued. This is known to strongly affect the properties of the deposited superconducting thin film. This study focuses on determining the optimal procedure to enhance homogeneity and smoothness of the copper surface. OFHC copper substrates have been processed using mechanical polishing (MP), chemical polishing (CP) and electropolishing (EP) procedures as well as a combina-tion thereof. The parameters of each of the procedures have been tested and optimised to produce the smoothest surface possible. The resulting samples have been analysed using a scanning electron microscope, a laser profilometer and a confocal microscope. Results indicate the superior per-formance of electrochemical polishing over chemical polishing in terms of planarization efficiency, while a combination of mechanical polishing followed by electropolishing provides the most homogeneous and smooth surface when utilising the critical current density of the electrolyte.

Poster THP042 [1.190 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP042

About •

paper received ※ 22 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP043

Deposition Parameter Effects on Niobium Nitride (NbN) Thin Films Deposited Onto Copper Substrates with DC Magnetron Sputtering

site, cathode, ECR, niobium

945

S.B. Leith, X. Jiang, M. Vogel
University Siegen, Siegen, Germany
R. Ries, E. Seiler
Slovak Academy of Sciences, Institute of Electrical Engineering, Bratislava, Slovak Republic

Funding: The EASITrain project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant No 764879.
As part of efforts to improve the performance of SRF cavities, to that prescribed by future operating requirements, alternative materials are currently being investigated. NbN is one of the alternatives under investigation to provide these better performance figures. In this contribution, a summary of results from an investigation into DC magnetron sputtered NbN thin films deposited onto copper substrates is presented. The copper substrates were prepared using a mechanical polishing process, followed by a chemical etching process. The NbN films were prepared in a large scale commercial coating system. A high and low value for the substrate temperature, process pressure, bias voltage, cathode power, nitrogen gas percentage, and the working gas type, using either Argon or Krypton, constitute the parameters of this study. The base pressure of the system prior to deposition was 5x10⁷ hPa for all coatings. The resulting films have been characterised using various surface characterisation methods to determine the effects of the deposition parameters during the film growth process. The deposition parameters have been optimised based on the characterisation results.

Poster THP043 [1.169 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP043

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP044

RF Characterization of Novel Superconducting Materials and Multilayers

niobium, SRF, site, plasma

950

T.E. Oseroff, M. Liepe, Z. Sun
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
B. Moeckly
STI, Santa Barbara, California, USA
M.J. Sowa
Veeco-CNT, Medford, USA

Cutting edge SRF technology is likely approaching the fundamental limitations of niobium cavities operating in the Meissner state. This combined with the obvious advantages of using higher critical temperature superconductors and thin film depositions leads to interest in the RF characterization of such materials. A TE mode niobium sample host cavity was used to characterize the RF performance of 5" (12.7 cm) diameter sample plates as a function of field and temperature at 4 GHz. Materials studied include MgB₂ and thin film atomic layer deposition (ALD) NbN and NbTiN on Nb substrates. These higher critical temperature superconductors all having coherence lengths on the order of a few nm. It is therefore likely that defects on the order of the coherence lengths will cause early flux penetration well before the theorized superheating field of an ideal superconducting surface. Superconductor-insulator-superconductor (SIS) multilayers have been proposed as a mechanism of arresting these early penetration flux avalanches and are therefore studied here as well, using the same NbN and NbTiN films, but over thin layers of insulating AlN on Nb substrates.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP044

About •

paper received ※ 02 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP045

Improvements to the Cornell Sample Host System

niobium, SRF, coupling, quadrupole

956

T.E. Oseroff, M. Liepe
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA

RF characterization of arbitrary superconducting samples has been of interest for many years but, due to the experimental complexities, has never been achieved to its full potential. A TE mode niobium sample host cavity has been used at Cornell to characterize the RF performance of 5" (12.7 cm) diameter sample plates. It was designed and built in 2012 – 2013 and since then has encountered a range of problems. The focus of this work is to highlight these and to present solutions to assist future researchers hoping to design novel RF characterization instruments. Topics covered include coupler design, cryostat support structure, sample preparation, and a discussion of potential systematic errors introduced by the data extraction and calibration methods applied to this device.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP045

About •

paper received ※ 01 July 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP046

Magnetic Field Mapping System for Cornell Sample Host Cavity

SRF, monitoring, cryomodule, radio-frequency

961

S.N. Lobo, M. Liepe, T.E. Oseroff
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA

Funding: Cornell Laboratory for Accelerator-Based Sciences and Education
Dissipation due to flux trapping is a persistent problem experienced in SRF cavity testing and cryomodule operation. This work addresses accurately and cheaply measuring magnetic fields in a cryostat without using delicate and expensive fluxgate magnetometers. Anisotropic Magnetoresistive (AMR) magnetic field sensors were investigated for the detection of small fields in a cryogenic environment. Initial development of instrumentation using 16 AMR sensors is presented for the purpose of measuring magnetic fields perpendicular the normal of a 5" diameter sample plate on the Cornell sample host cavity.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP046

About •

paper received ※ 29 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP047

Progress of TRIUMF Beta-SRF Facility for Novel SRF Materials

SRF, optics, niobium, radio-frequency

964

E. Thoeng
UBC & TRIUMF, Vancouver, British Columbia, Canada
R.A. Baartman, P. Kolb, R.E. Laxdal, B. Matheson, G. Morris, N. Muller, S. Saminathan
TRIUMF, Vancouver, Canada
T. Junginger
UVIC, Victoria, Canada

Funding: NSERC (Natural Sciences and Engineering Research Council of Canada)
SRF cavities made with bulk Nb have been the backbone of high-power modern linear accelerators. Demands for higher energy and more efficient linear accelerators, however, have strained the capabilities of bulk Nb close to its fundamental limit. Several routes have been proposed using thin film novel superconductors (e.g. Nb₃Sn), SIS multilayer, and N-doping. Beta-NMR techniques are more suitable for the characterization of Meissner state in these materials, due to the capability of soft-landing radioactive ions on the nanometer scale of London penetration depth, as compared to micrometer probe of the muSR technique. Upgrade of the existing beta-NQR beamline, combined with the capability of high parallel magnetic field (200 mT) are the scope of the beta-SRF facility which has been fully funded. All hardware required for the upgrade has also been procured. The status of the commissioning, which is currently in phase I, is reported here, together with the future schedule of phase II with the fully installed beta-SRF beamline. Finally, the detail layout of the completed beamline and sample requirements will be included in this paper which might be of interest of future users.

Poster THP047 [1.372 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP047

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP049

Commissioning the JLab LERF Cryomodule Test Facility

cryomodule, controls, LLRF, MMI

973

C. Hovater, R. Bachimanchi, E. Daly, M.A. Drury, L.E. Farrish, J. Gubeli, N.A. Huque, K. Jordan, M.E. Joyce, L.K. King, M. Marchlik, W. Moore, T.E. Plawski, A.D. Solopova, C.M. Wilson
JLab, Newport News, Virginia, USA
A.L. Benwell, C. Bianchini, D. Gonnella, S.L. Hoobler, K.J. Mattison, J. Nelson, A. Ratti, B.H. Ripman, S. Saraf, L.M. Zacarias
SLAC, Menlo Park, California, USA
L.R. Doolittle, S. Paiagua, C. Serrano
LBNL, Berkeley, California, USA

The JLab Low Energy Recirculating Facility, LERF, has been modified to support concurrent testing of two LCLS-II cryomodules. The cryomodules are installed in a similar fashion as they would be in the L1 section of the LCLS-II linac, including the floor slope and using all of the LCLS-II hardware and controls for cryomodule cryogenics, vacuum, and RF (SSA and LLRF). From the start, it was intended to use LCLS-II electronics and EPICS software controls for cryomodule testing. In affect the LERF test facility becomes the first opportunity to commission and operate the LCLS-II LINAC hardware and software controls. Support for specific cryomodule high level test applications like Q₀ and HOMs measurements, are being developed from the basic cryomodule control suite. To support the testing, 2 K He is supplied from the CEBAF south linac cryogenic system, where care must be taken when using the LERF test facility to not upset the CEBAF cryogenics plant. This paper discusses the commissioning of the hardware and software development for testing the first two LCLS-II cryomodules.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP049

About •

paper received ※ 22 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP050

Measurement of the Magnetic Field Penetration into Superconducting Thin Films

experiment, solenoid, SRF, FEL

978

I.H. Senevirathne, G. Ciovati, J.R. Delayen
ODU, Norfolk, Virginia, USA
G. Ciovati, J.R. Delayen
JLab, Newport News, Virginia, USA

The magnetic field at which first flux penetrates is a fundamental parameter characterizing superconducting materials for SRF cavities. Therefore, an accurate technique is needed to measure the penetration of the magnetic field directly. The conventional magnetometers are inconvenient for thin superconducting film measurements because these measurements are strongly influenced by orientation, edge and shape effects. In order to measure the onset of field penetration in bulk, thin films and multi-layered superconductors, we have designed, built and calibrated a system combining a small superconducting solenoid capable of generating surface magnetic field higher than 500 mT and Hall probe to detect the first entry of vortices. This setup can be used to study various promising alternative materials to Nb, especially SIS multilayer coatings on Nb that have been recently proposed to delay the vortex penetration in Nb surface. In this paper, the system will be described and calibration will be presented.

Poster THP050 [1.201 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP050

About •

paper received ※ 20 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP051

Upgrades to Cryogenic Capabilities for Cryomodule Testing at JLab

cryomodule, cryogenics, operation, HOM

983

N.A. Huque, E. Daly, T. Wijeratne
JLab, Newport News, Virginia, USA

The cryogenic facilities for cryomodule testing at Jefferson Lab (JLab) have been modified and to enable testing of Linear Coherent Light Source-II (LCLS-II) cryomodules. Temporary changes in u-tube connections at the Cryogenic Test Facility (CTF) has enabled rates of cavity cooling that are a factor of 10 higher than previously achieved. Cryogenic connections at JLab¿s Low Energy Recirculator Facility (LERF) have been repurposed to enable two LCLS-II cryomodules to be tested in series. This testing shares the helium space with the Central Helium Liquefier (CHL) that is also used by the Continuous Electron Beam Accelerator Facility (CEBAF). Cryomodule testing can occur while beam operation is ongoing at CEBAF. Improvements to these facilities have allowed the testing of the JLab¿s highest ever performing cryomodules.

Poster THP051 [0.722 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP051

About •

paper received ※ 20 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP052

Pansophy Enhancements for SRF Through Collecting and Analyzing Inputs/Outputs to Further Project Efficiency in Reporting and Performance

cryomodule, status, feedback, monitoring

988

V.D. Bookwalter, M. Dickey, M.G. McDonald, E.A. McEwen
JLab, Newport News, Virginia, USA

SRF Cavity and Cryomodule testing and production requires a consistent means of collecting and analyzing data against quality and production parameters. JLab’s engineering data management system, Pansophy, is utilized to assist project leaders and subject matter experts (SMEs) with such tasks, by providing a means to data mine key parameter indicators (KPI) and production planning and status data. Recent enhancements to reporting and trending have been utilized for the LCLS-II and CEBAF 12 GeV upgrade projects. Further enhancements are being planned for future projects, like SNS-PPU, such as KPI trending, KPI quality, vendor quality, production timelines and user defined queries. Being able to understand past trends will assist with enhancements to future projects.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP052

About •

paper received ※ 21 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP053

Analysis of the Results of the Tests of IFMIF Accelerating Units

cryomodule, SRF, vacuum, linac

992

N. Bazin, S. Chel, M. Desmons, G. Devanz, H. Jenhani, O. Piquet
CEA-DRF-IRFU, France

The prototype IFMIF-EVEDA cryomodule encloses eight superconducting 175 MHz β=0.09 Half-Wave Resonators (HWR). They are designed together with the power coupler to accelerate a high intensity deuteron beam (125 mA) from to 5 to 9 MeV. Two cavity packages, complete with tuning system and power couplers, have been tested in a dedicated horizontal test cryostat - SaTHoRI (Satellite de Tests HOrizontal des Résonateurs IFMIF). The successful operational equivalent tests and tuning of the SRF accelerating units is reported.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP053

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP054

Cryogenic Installations for Module Tests at Mainz

cryogenics, cryomodule, operation, SRF

997

F. Hug, K. Aulenbacher, E. Schilling, D. Simon, T. Stengler, S.D.W. Thomas
KPH, Mainz, Germany
K. Aulenbacher, T. Kürzeder
HIM, Mainz, Germany
A. Skora
IKP, Mainz, Germany

Funding: This work is supported by the German Research Foundation (DFG) under the Cluster of Excellence "PRISMA+" EXC 2118/2019
At Helmholtz Institute Mainz a cryomodule test bunker has been set up for testing dressed modules at 2 K. In a first measurement campaign the high power rf tests of two 1.3 GHz cryomodules for the future MESA accelerator have been performed. We will report on the performance of the test setup, the present and upcom-ing cryogenic installations at the Institute for Nuclear Physics at Mainz, and in particular on the Helium re-frigeration and transport system comprising of a 220 m transport line for liquified gases.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP054

About •

paper received ※ 29 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP055

Magnetic Field Induced by Thermo Electric Current in LCLS-II Cryomodules

cryomodule, SRF, niobium, vacuum

1003

G. Wu, S.K. Chandrasekaran
Fermilab, Batavia, Illinois, USA

Funding: The work is supported by Fermilab which is operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
Seebeck effect of metals play an important role in cryomodule design. As cryomodule cools down from room temperature down to nominal cavity operating temperature, components in a cryomodule experiences different temperatures. Some components such as power couplers cross from room temperature to 2 K. Thermo electric current forms loops circulating through and around cavities. Such current loops will generate additional magnetic field that could be trapped into cavity wall during superconducting transition as well as during cavity quench. These trapped field can degrade cavity quality factor and increase heat load. Simple circuit model is proposed and compared to calculated trapped field during cryomodule tests.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP055

About •

paper received ※ 26 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP056

Current Results From Acceptance Testing of LCLS-II Cryomodules at Jefferson Lab

cryomodule, HOM, controls, operation

1007

M.A. Drury, E. Daly, N.A. Huque, L.K. King, A.D. Solopova
JLab, Newport News, Virginia, USA
J. Nelson, B.H. Ripman, L.M. Zacarias
SLAC, Menlo Park, California, USA

Funding: This work was supported by the LCLS-II Project and the U.S. Department of Energy, Contract DE-AC02-76SF00515.
The Thomas Jefferson National Accelerator Facility is currently engaged, along with several other Department of Energy (DOE) national laboratories, in the Linac Co-herent Light Source II project (LCLS-II). The SRF Insti-tute at Jefferson Lab is currently building 21 cryomod-ules for this project. The cryomodules are based on the XFEL design and have been modified for continuous wave (CW) operation and to comply with other LCLS-II specifications. Each cryomodule contains eight 9-cell cavities with coaxial power couplers operating at 1.3 GHz. The cryomodule also contain a magnet package that consists of a quadrupole and two correctors. Most of these cryomodules will be tested in the Cryomodule Test Facility (CMTF) at Jefferson Lab before shipment to SLAC. Up to three of these cryomodules will be tested in a test stand set up in the Low Energy Recovery Facility (LERF) at Jefferson Lab. Acceptance testing of the LCLS-II cryomodules began in December 2016. Twelve cryomodules have currently completed Acceptance Test-ing. This paper will summarize the results of those tests.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP056

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP058

Conditioning Experience of the ESS Spoke Cryomodule Prototype

cryomodule, vacuum, operation, hardware

1011

A. Miyazaki, K. Fransson, K.J. Gajewski, L. Hermansson, H. Li, R.J.M.Y. Ruber, R. Santiago Kern, R. Wedberg
Uppsala University, Uppsala, Sweden

The prototype cryomodule for the ESS double spoke cavities is tested in the FREIA laboratory at Uppsala University. One of the goals of this test is to establish an efficient way to assess one series cryomodule within a due time (about one month). In 2017, the dedicated high-power test for dressed cavities in the horizontal cryostat (HNOSS) revealed that one of the possible challenges is a conditioning process of the coupler and cavity multipacting. Each process should not damage any components of the cryomodule but at the same time it should be finished in a reasonable time scale. More importantly, unlike the previous tests in the vertical or horizontal cryostat, conditioning two cavities in one cryomodule in due time may require parallel processing in some part of the procedure. This study will be the first practical experience of double spoke cavity conditioning in a cryomodule, and will lead to a standard conditioning recipe for future projects containing superconducting spoke cavities. In this presentation, a preliminary result of cryomodule testing will be shown with a special focus on the conditioning processes.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP058

About •

paper received ※ 01 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP059

RF Incoming Inspection of 1.3 GHz Cryomodules for LCLS-II at SLAC National Accelerator Laboratory

cryomodule, HOM, linac, controls

1014

S. Aderhold, C. Adolphsen, A. Burrill, D. Gonnella, J. Nelson
SLAC, Menlo Park, California, USA

Funding: This work was supported by the US DOE and the LCLS-II Project.
The main part of the SRF linac for the Linac Coherent Light Source II (LCLS-II) at SLAC National Accelerator Laboratory will consist of 35 cryomodules with superconducting RF cavities operating at 1.3 GHz. The cryomodules are assembled and tested at Fermi National Accelerator Laboratory and Thomas Jefferson National Accelerator Facility. Following the transport to SLAC, the cryomodules undergo several incoming inspection steps before ultimately being moved to the tunnel for installation in the linac. The RF part of the incoming inspection covers measurements of a number of parameters like cavity frequency spectrum, notch filter frequency of the higher order mode couplers and external quality factor Q_ext of the input coupler. The inspection results are compared to measurements at the partner labs prior to shipping and the nominal values in order to verify that the cryomodules have not been damaged during the transport and are ready for installation. We present an overview and analysis of the inspections for the cryomodules received to date.

Poster THP059 [1.223 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP059

About •

paper received ※ 02 July 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP060

Experience With LCLS-II Cryomodule Testing at Fermilab

cryomodule, operation, detector, SRF

1018

E.R. Harms, E. Cullerton, C.M. Ginsburg, B.J. Hansen, B.D. Hartsell, J.P. Holzbauer, J. Hurd, V.S. Kashikhin, M.J. Kucera, F.L. Lewis, A. Lunin, D.L. Newhart, D.J. Nicklaus, P.S. Prieto, O.V. Prokofiev, J. Reid, N. Solyak, R.P. Stanek, M.A. Tartaglia, G. Wu
Fermilab, Batavia, Illinois, USA
C. Contreras-Martinez
FRIB, East Lansing, Michigan, USA
J. Einstein-Curtis
Private Address, Naperville, USA

Funding: This manuscript has been authored by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the U.S. Department of Energy, Office of Science, Office of High Energy Physics.
The Cryomodule Test Stand (CMTS1) at Fermilab has been engaged with testing 8-cavity 1.3 GHz cryomodules designed and assembled for the LCLS-II project at SLAC National Accelerator Laboratory since 2016. Over these three years twenty cryomodules have been cooled to 2K and power tested in continuous wave mode on a roughly once per month cycle. Test stand layout and testing procedures are presented together with results from the cryomodules tested to date. Lessons learned and future plans will also be shared.

Poster THP060 [2.774 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP060

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP061

Performance of FRIB Production Quarter-Wave and Half-Wave Resonators in Dewar Certification Tests

cryomodule, SRF, linac, MMI

1023

W. Hartung, W. Chang, S.H. Kim, D. Norton, J.T. Popielarski, K. Saito, J.F. Schwartz, T. Xu, C. Zhang
FRIB, East Lansing, Michigan, USA

The Facility for Rare Isotope Beams (FRIB) is under construction at Michigan State University (MSU). The FRIB superconducting driver linac will accelerate ion beams to 200 MeV per nucleon. The driver linac requires 10⁴ quarter-wave resonators (QWRs, β = 0.041 and 0.085) and 220 half-wave resonators (HWRs, β = 0.29 and 0.54). The jacketed resonators are Dewar tested at MSU before installation into cryomodules. The cryomodules for β = 0.041, 0.085, and 0.29 have been completed and certified; 88% of the β = 0.54 HWRs have been certified (as of March 2019). Beam commissioning of the QWR cryomodules is in progress. The Dewar certification tests have provided valuable statistics on the performance of production QWRs and HWRs at 4.3 K and 2 K and on performance limits. Results will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP061

About •

paper received ※ 12 July 2019 paper accepted ※ 13 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP062

Progress in FRIB Cryomodule Bunker Tests

cryomodule, solenoid, SRF, operation

1029

W. Chang, S. Caton, A. Ganshyn, W. Hartung, S.H. Kim, B. Laumer, H. Maniar, J.T. Popielarski, K. Saito, M. Xu, T. Xu, C. Zhang, S. Zhao
FRIB, East Lansing, Michigan, USA

Funding: Work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661
The Facility for Rare Isotope Beams (FRIB) is under construction at Michigan State University (MSU). The FRIB superconducting driver linac will accelerate ion beams to 200 MeV per nucleon. The driver linac requires 104 quarter-wave resonators (QWRs, β = 0.041 and 0.085) and 220 half-wave resonators (HWRs, β = 0.29 and 0.54). The jacketed resonators are Dewar tested at MSU before installation into cryomodules. The cryomodules for β = 0.041, 0.085, and 0.29 have been completed and certified; 32 out of 49 cryomodules are certified via bunker test (as of March 2019). FRIB cryomodule needs 74 solenoid packages: 8-25 cm packages for 0.041 QWR CMs, 36-50 cm for 0.085 CMs, 12-50 cm for 0.29 CMs, and 18-50 cm for 0.53 CMs. The bunker certification completed 58 packages. All the magnets energized at FRIB goal (90 A/8 T for solenoid and 19 A/0.064 Tm for dipoles), all cavities tested at or above specified operating gradient. In this paper, we report the bunker test result.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP062

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP063

Inivestigation of the Possibility of High Efficiency L-Band SRF Cavity for Medium-Beta Heavy Ion Multi-Charge-State Beams

linac, emittance, cryomodule, heavy-ion

1035

S.M. Shanab, K. Saito, Y. Yamazaki
FRIB, East Lansing, Michigan, USA

Funding: This work was supported in part by the U.S. National Science Foundation, under Grant PHY-1102511 and by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661.
The possibility of L-band SRF elliptical cavity in order to accelerate heavy ion multi-charge-state beams is being investigated for accelerating energy higher than 200 MeV/u. A first simple analytic study was performed and the result showed that the longitudinal acceptance of 1288 MHz is sufficient for heavy-ion multi-charge-state (5 charge states) medium-beta linac. Encouraged this result, detail beam dynamic simulation took place. The cryogenic heat load is also calculated for this linac with taken into consideration cavity doping technology. In this paper, a summary of the beam dynamics and cryogen-ic heat load calculations for 1288 MHz linac for heavy-ion multi-charge-state (5 charge states) medium-beta beams.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP063

About •

paper received ※ 24 June 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP064

The Cryostat Results of Carbon Contamination and Plasma Cleaning for the Field Emission on the SRF Cavity

plasma, SRF, experiment, cryogenics

1038

A.D. Wu, Q.W. Chu, H. Guo, Y. He, S.C. Huang, C.L. Li, F. Pan, Y.K. Song, T. Tan, P.R. Xiong, W.M. Yue, S.H. Zhang, H.W. Zhao
IMP/CAS, Lanzhou, People’s Republic of China

The field emission effect is the mainly limitation for the operating of SRF cavities in higher gradient with stability. In this paper, the experiments were performed to evaluate the impact of the carbon contaminants and plasma cleaning on the performance of SRF cavity. Contamination mechanism was classified into cryogenic adsorption with weak strength and chemical deposition with strong strength. For the weak strength condition, the methane was injected into the SRF cavity during vertical test to make a cryogenic adsorption layer on the inner surface of the cavity. The results revealed that the performance of SRF cavity degraded by methane physical adsorption, but the performance can be recovered by thermal cycle the cavity to 300K and pump methane out. For the strong strength condition, the chemical deposited dirty layer of carbon contamination was produced by using of Ar/CH₄ mixed PECVD method, and the SRF cavity performance was deteriorated by the severe field emission. Finally, carbon deposited cavity was treated by the Ar/O2 plasma, and its results revealed that the field emission removed greatly and the gradient was increased.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP064

About •

paper received ※ 20 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP067

Cavity Tilt Measurement in a 1.3 GHz Superconducting Cryo-Module at FLASH

dipole, polarization, HOM, electron

1041

J.H. Wei
USTC/NSRL, Hefei, Anhui, People’s Republic of China
N. Baboi
DESY, Hamburg, Germany
T. Hellert
LBNL, Berkeley, California, USA

TESLA superconducting (SC) cavities are used for the acceleration of electron bunches at FLASH. The Higher Order Modes (HOMs) excited by the beam in these cavities may cause emittance growth. The misalignment of the cavities in a cryo-module is one of the essential factors which enhance the coupling of the HOMs to the beam. The cavity offset and tilt are the two most relevant misalignments. These can be measured by help of dipole modes, based on their linear dependence on the beam offset. The cavity offset has been measured before in several modules at FLASH. However, the cavity tilt has so far proved to be difficult to be measured, because the angular dependence of the dipole mode is much weaker. By carefully targeting the beam through the middle of a cavity, the strong offset contribution to the dipole fields could be reduced. Careful data analysis based on a fitting method enabled us then to extract the information on the cavity tilt. This measurement has been implemented in the cavities in one cryo-module at FLASH. First results of the ongoing measurements from several cavities are presented in this paper. It is for the first time that the cavity tilt in several cavities has been measured.

Poster THP067 [1.392 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP067

About •

paper received ※ 23 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP068

Evaluation of Low Heat Conductivity RF Cables

vacuum, insertion, cryogenics, SRF

1045

G. Cheng, G. Ciovati, M.L. Morrone
JLab, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
New potential applications of superconducting radio-frequency can be envisioned with conduction cooling of the cavities using cryocoolers. In this case, the total heat load to the cryocoolers have to be carefully managed to assure sufficient margin to operate the cavity at an acceptable accelerating gradient. The static and dynamic heat load from rf cables connected to the cavity can be a significant contribution to the total heat load. In this contribution we report the results from measurements of the temperature profile at 1.3 GHz for two low heat conductivity rf cables, as a function of the rf power and with one end of the cable in thermal contact with a liquid helium bath at 4.3 K. A parametric model of the two cables was developed with ANSYS to match the temperature profiles and calculate the heat load at the cold end of the cable.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP068

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP070

CEPC HOM Coupler R&D

HOM, collider, SRF, cryomodule

1050

H.J. Zheng, F. Meng, P. Sha, J.Y. Zhai
IHEP, Beijing, People’s Republic of China

The conceptual design report (CDR) for the Circular Electron Positron Collider (CEPC) has been published in September 2018. In this talk, the CDR design and prototyping of the HOM coupler for the CEPC Collider ring cavity will be given. Each cavity has two detachable coaxial HOM couplers mounted on the cavity beam pipe with HOM power handling capacity of 1 kW. A double notch coupler is chosen due to its wide bandwidth for the fundamental mode. A prototype of this HOM coupler and a coaxial line test bench have been fabricated and tested under low power. The low power test results agree well with the simulation results. The high power test was also carried out in room temperature.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP070

About •

paper received ※ 19 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP071

HOM Measurement Results for CEPC 650 MHz 2-cell Cavity

HOM, damping, collider, cryomodule

1055

H.J. Zheng, F. Meng, J.Y. Zhai
IHEP, Beijing, People’s Republic of China

CEPC will use a 650 MHz RF system with 240 2-cell cavities for the Collider. The Collider is a double-ring with shared cavities for Higgs operation and separate cavities for W and Z operations. The higher order modes (HOM) excited by the intense beam bunches must be damped to avoid additional cryogenic loss and multi-bunch instabilities. In this paper, the impedance budget and HOM damping and HOM power requirement for the CEPC Collider ring are given. This HOM power limit and the fast-growing longitudinal coupled-bunch instabilities (CBI) driven by both the fundamental and higher order modes impedance of the RF cavities determine to a large extent the highest beam current and luminosity obtainable in the Z mode. Two prototypes of HOM coupler have been fabricated and installed on the 650 MHz 2-cell cavity. The higher order modes were verified by bead pulling method. The Qe for the HOMs were also measured. A test bench with two 2-cell cavities was used to measure the real damping results and HOM propagating properties for a cavity string.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP071

About •

paper received ※ 19 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP072

Development of HOM Absorbers for CW Superconducting Cavities in Energy Recovery Linac

HOM, superconducting-cavity, linac, SRF

1060

T. Ota, S. Nakamura, K. Sato, M. Takasaki
Toshiba Energy Systems & Solutions Corporation, Keihin Product Operations, Yokohama, Japan
E. Kako, T. Konomi, H. Sakai, K. Umemori
KEK, Ibaraki, Japan
A. Miyamoto
Toshiba, Yokohama, Japan

Higher Order Modes (HOM) absorbers for superconducting cavities have been developing at TOSHIBA in collaboration with High Energy Accelerator Research Organization (KEK) since 2015. A new prototype HOM absorber for 1.3 GHz 9-cell superconducting cavity was fabricated. An AlN lossy dielectrics cylinder was brazed with a thin copper plate, and the cool-down tests by nitrogen gas was carried out. The copper plate and a copper cylinder were joined by electron beam welding. SUS flanges were electron beam welded to both ends of the copper cylinder to fabricate a whole prototype HOM absorber. Fabrication process of the prototype HOM absorber will be presented in this paper.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP072

About •

paper received ※ 21 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP073

Advanced LLRF System Setup Tool for RF Field Regulation of SRF Cavities

controls, feedback, FEL, electron

1063

S. Pfeiffer, J. Branlard, M. Hoffmann, Ch. Schmidt
DESY, Hamburg, Germany

Feedback operation at the European XFEL ensures an amplitude and phase stability of 0.01% and 0.01 deg, respectively. To reach such high RF field stability, model-based approaches for RF field system characterization and RF field controller design are in use. High demand on this system modelling is set especially to the characterization of additional passband modes for small bandwidth SRF cavities operated in pulsed mode and vector-sum regulation. This contribution discusses the developed "Advanced system setup tool" using a graphical user implementation in Matlab® for the RF field system characterization and the multiple-input-multiple-output feedback controller setup. Examples and current limitations will be presented.

Poster THP073 [0.873 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP073

About •

paper received ※ 19 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP074

Microphonics Noise Suppression with Observer Based Feedback

controls, SRF, resonance, linac

1068

M. Keikha, K. Fong
TRIUMF, Vancouver, Canada
M. Moallem
SFU, Surrey, Canada

Funding: TRIUMF
Detuning of superconducting radio frequency (SRF) cavities is mainly caused by the Lorentz force, which is the radiation pressure induced by a high radio frequency (RF) field, and environmental mechanical vibrations that induce undesirable interference signals referred to as microphonics. Both of these influences can be described by a second order differential equation of the mechanical vibration modes of the cavity. In this paper we consider three dominant mechanical modes of the system and develop a control scheme based on input-output linearization. It is shown through simulation studies that the proposed control technique can successfully the suppress microphonic noise due to the SRF cavity¿s dynamics.

Poster THP074 [0.610 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP074

About •

paper received ※ 22 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP075

Development of a 166.6 MHz Digital LLRF System for HEPS-TF Project

LLRF, controls, low-level-rf, superconducting-cavity

1073

Q.Y. Wang, J.P. Dai, T.M. Huang, D.B. Li, H.Y. Lin, Z.H. Mi, P. Zhang
IHEP, Beijing, People’s Republic of China

A 166.6 MHz superconducting RF system has been proposed for the High Energy Photon Source (HEPS), a 6 GeV kilometer-scale light source. A 166.6MHz digital low-level RF system for HEPS-TF project has been developed firstly. And the digital low-level RF system has been successfully applied to the horizontal high power test of 166.6MHz superconducting cavity. The cavity field stability has been successfully achieved about ±0.03% (pk-pk) in amplitude and ±0.02 degree (pk-pk) in phase while the cavity field voltage is up to 1.2MV. It can meet the field stability requirements towards ±0.1% in ampli-tude and ±0.1 degree in phase of HEPS project. Further study and optimization of the system is under way.

Poster THP075 [1.612 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP075

About •

paper received ※ 29 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP076

Simulation Analysis of Lorentz Force Induced Oscillations in RF Cavities in Vector Sum and Cw Operation

operation, controls, simulation, alignment

1078

R. Leewe, K. Fong
TRIUMF, Vancouver, Canada

Within TRIUMFs electron LINAC, two TESLA type cavities are operated with a single klystron in CW mode. Vector sum control is applied for field stabilization and the resonance frequencies are individually tuned with a proportional feedback controller. First operational experiences showed that amplitude oscillations can start in both cavities, while the vector sum is perfectly stable. These instabilities occur at high operating fields and are driven by Lorentz force changes. This paper presents a simulation study of multiple cavities in vector sum operation with respect to Lorentz force oscillations. It will be shown that all cavities in operation have to be damped to guarantee system stability.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP076

About •

paper received ※ 22 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP078

CERN’s SRF Test Stand for Cavity Performance Measurements

controls, LLRF, operation, interface

1082

N. Stapley, J. Bastard, M.R. Coly, A.E. Ivanov, A. Macpherson, N.C. Shipman, K. Turaj
CERN, Geneva, Switzerland
I. Ben-Zvi
BNL, Upton, New York, USA
A. Castilla
Cockcroft Institute, Lancaster University, Lancaster, United Kingdom
K. Hernandez-Chahin
Universidad de Guanajuato, División de Ciencias e Ingenierías, León, Mexico
M. Wartak, A. Zwozniak
IFJ-PAN, Kraków, Poland

Recent deployment of a digital LLRF system within the cavity testing framework of CERN’s vertical test cryostats has permitted a full revamp of cavity performance validation. With both full continuous and pulse mode operation, steady state a transient RF behaviour can be effectively probed. Due to direct and integrated control and monitoring of environmental test conditions, standard and novel RF measurement procedures have been developed and integrated into the testing infrastructure, along with a coherent data flow of high granularity measurement data. We present an overview of this cavity measurement system and address the underlying architectural structure, data handling and integration of user interfaces. In addition we highlight the benefits of variety of RF cavity measurements that can now be accommodated in our large 2 K cryostats.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP078

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP080

Status of the All Superconducting Gun Cavity at DESY

cathode, SRF, gun, niobium

1087

E. Vogel, S. Barbanotti, A. Brinkmann, Th. Buettner, J.I. Iversen, K. Jensch, D. Klinke, D. Kostin, W.-D. Möller, A. Muhs, J. Schaffran, M. Schmökel, J.K. Sekutowicz, S. Sievers, L. Steder, N. Steinhau-Kühl, A. Sulimov, J.H. Thie, H. Weise, M. Wenskat, M. Wiencek, L. Winkelmann, B. van der Horst
DESY, Hamburg, Germany

At DESY, the development of a 1.6-cell, 1.3 GHz all superconducting gun cavity with a lead cathode attached to its back wall is ongoing. The special features of the structure like the back wall of the half-cell and cathode hole require adaptations of the procedures used for the treatment of nine-cell TESLA cavities. Unsatisfactory test results of two prototype cavities motivated us to re-consider the back-wall design and production steps. In this contribution we present the status of the modified cavity design including accessories causing accelerating field asymmetries, like a pick up antenna located at the back wall and fundamental power- and HOM couplers. Additionally, we discuss preliminary considerations for the compensation of kicks caused by these components.

Poster THP080 [7.365 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP080

About •

paper received ※ 20 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP081

A Cryocooled Normal Conducting and Superconducting Hybrid CW RF Gun

gun, cathode, acceleration, emittance

1091

H.J. Qian, G. Shu, F. Stephan
DESY Zeuthen, Zeuthen, Germany
S. Barbanotti, B. Petersen, E. Vogel
DESY, Hamburg, Germany
A.A. Gorchakov, M. Gusarova
MEPhI, Moscow, Russia

Continuous wave (CW) photoinjectors have seen great progress in the last decades, such as DC gun, superconducting RF (SRF) gun and normal conducting (NC) gun. Developments of Free electron lasers and electron microscopy in the CW mode are pushing for further improvements of CW guns towards higher acceleration gradient, higher beam energy and compatibility with high QE cathodes for better beam brightness. Current SC gun gradient is limited by the cathode cell due to the complication of a cathode back plane and a normal conducting cathode plug, and R&D on SC gun improvement is ongoing. A high gradient cryocooled CW NC gun was proposed to house the high QE cathode, and a SC cavity immediately nearby gives further energy acceleration. In this paper, further RF optimization of the NC gun and ASTRA simulations of such a hybrid photoinjector are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP081

About •

paper received ※ 25 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP082

Geometry Dependent Beam Dynamics of a 3.5-cell SRF Gun Cavity at ELBE

SRF, gun, emittance, electron

1095

K. Zhou
CAEP/IAE, Mianyang, Sichuan, People’s Republic of China
A. Arnold, S. Ma, J. Schaber, J. Teichert, R. Xiang
HZDR, Dresden, Germany

In order to optimize the next generation SRF gun at HZDR ELBE radiation source, the impact on beam dynamics from the SRF cavity geometry needs to be investigated. This paper presents an analysis on the electromagnetic fields and output electron beam qualities, by changing the geometry parameters of a 3.5-cell SRF gun cavity. The simulation results show the higher electric field ratio in the first half cell to the TESLA like cell, the better beam parameters we can obtain, which, however, will also lead to a higher Emax/E0 and Bmax/E0.

Poster THP082 [1.935 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP082

About •

paper received ※ 22 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP086

Preliminary Design of Superconducting Cavity Test Platform in CSNS Campus

superconducting-cavity, cryomodule, SRF, controls

1104

S.H. Liu, X. Li, W. Long, H. Sun, S. Wang, C.L. Zhang, J.Y. Zhu
IHEP, People’s Republic of China
S.Y. Chen, Y. Liu, C. Shi
DNSC, Dongguan, People’s Republic of China
P.C. Wang, B. Wu
IHEP CSNS, Guangdong Province, People’s Republic of China

For the beam power upgrade of CSNS (China Spallation Neutron Source) and the construction of the high performance photon source in South China in the near future, the superconducting cavity test platform which includes vertical test stand, single cavity horizontal test stand, cryomodule horizontal test stand and coupler test stand will be built. This paper will generally introduce the preliminary design of the test platform and corresponding test parameters.

Poster THP086 [0.171 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP086

About •

paper received ※ 21 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP087

2 K SUPERFLUID HELIUM CRYOGENIC VERTICAL TEST STAND OF PAPS

cryogenics, vacuum, superconducting-cavity, SRF

1107

L.R. Sun, R. Ge, R. Han, Y.C. Jiang, S.P. Li, C.C. Ma, M.J. Sang, M.F. Xu, R. Ye, J.H. Zhang, X.Z. Zhang, Z.Z. Zhang, T.X. Zhao
IHEP, Beijing, People’s Republic of China

Platform of Advanced Photon Source Technology R&D (PAPS) in the Institute of High Energy Physics (IHEP) is an ongoing project, which aimed to provide a comprehensive research and testing platform for the particle accelerator, X-ray detection and optics. As one of the important parts of the platform, cryogenic vertical test stand for the superconducting cavities is composed of three big vertical test cryostats with 2 different inner diameters, which can provide 4.5K liquid helium, 2K superfluid helium and the lowest 1.5K environments according to the cavities test requirements. The cryogen-ic vertical test stands also focus on current international ¿hot spot¿ fast cool down to the superconducting cavi-ties, maximum liquid helium mass flow rate can be reached to 80g/s. Because of the big size of the cryostats and certain scale, the finished cryogenic vertical test stand can meet several different type cavities test, such as 1.3GHz 9cell, Spoke, elliptical, etc. And also can provide the cavities¿ mass vertical testing for the large scale superconducting accelerators.

Poster THP087 [1.182 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP087

About •

paper received ※ 20 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP088

Updates on the Inspection System for SRF Cavities

controls, superconducting-cavity, GUI, interface

1111

Y. Iwashita, H. Tongu
Kyoto ICR, Uji, Kyoto, Japan
H. Hayano
KEK, Ibaraki, Japan
Y. Kuriyama
Kyoto University, Research Reactor Institute, Osaka, Japan

Optical inspections on superconducting cavities are familiar to those who are involved in the cavity fabrications. Further improvements on the Kyoto Camera have been carried out these years together with further processing technique developments, such as removing found defects by local grinding techniques. Improvements on Kyoto Camera includes implementation of color LEDs for illumination system, which improves the inspection efficiency. These progresses will be reported.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP088

About •

paper received ※ 02 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP089

Development of Superconducting RF Double Spoke Cavity at IHEP

coupling, SRF, niobium, linac

1114

Q. Zhou, F.S. He, W.M. Pan
IHEP, Beijing, People’s Republic of China

The China Spallation Neutron Source (CSNS) is de-signed to produce spallation neutrons. CSNS upgrade is planned to increase beam power by inserting a SRF linac after drift tube linac (DTL). IHEP is developing a 325MHz double spoke cavity at ¿0 of 0.5 for the CSNS SRF linac. The cavity shape was optimized to minimize Ep/Ea while keeping Bp/Ep reasonably low. Meanwhile, mechanical design was applied to check stress, Lorentz force detuning and microphonic effects, and to minimize pressure sensitivity. A new RF coupling scheme was pro-posed to avoid electrons hitting directly on ceramic win-dow. After fabrication and post processing of cavity, the cavity reached Bp of 120mT at E_acc = 13.8MV/m and Q₀ = 1.72·10¹⁰ under vertical test at 2K.

Poster THP089 [2.176 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP089

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP090

Characterization of SSR1 Cavities for PIP-II Linac

radiation, cryomodule, multipactoring, linac

1120

A.I. Sukhanov, F.G. Garcia, B.M. Hanna, S. Kazakov, Y.M. Pischalnikov, O.V. Prokofiev, W. Schappert, I. Terechkine, V.P. Yakovlev, J.C. Yun
Fermilab, Batavia, Illinois, USA
C. Contreras-Martinez
FRIB, East Lansing, Michigan, USA
S. Samani
Queen Mary University of London, London, United Kingdom

A cryomodule of 325 MHz Single Spoke Resonator type 1 (SSR1) superconducting RF cavities is being built at Fermilab for the PIP-II project. Twelve SSR1 cavities were manufactured in industry in USA (10 cavities) and India (2 cavities) and delivered to Fermilab. In this paper we present results of characterization of fully integrated jacketed cavities with high power coupler and tuner at the Fermilab Spoke Test Cryostat (STC).

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP090

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP091

Upgrade of the Fermilab Spoke Test Cryostat for Testing of PIP-II 650 MHz 5-Cell Elliptical Cavities

vacuum, MMI, cryogenics, interface

1124

A.I. Sukhanov, S.K. Chandrasekaran, B.M. Hanna, T.H. Nicol, J.P. Ozelis, Y.M. Pischalnikov, D. Plant, O.V. Prokofiev, O.V. Pronitchev, V. Roger, W. Schappert, I. Terechkine, V.P. Yakovlev
Fermilab, Batavia, Illinois, USA
C. Contreras-Martinez
FRIB, East Lansing, Michigan, USA

Design of the high beta 650 MHz prototype cryomodule for PIP-II is currently undergoing at Fermilab. The cryomodule includes six 5-cell elliptical SRF cavities with accelerating voltage up to 20 MV and low heat dissipation (Q₀ > 3·10^zEhNZeHn). Characterization of performance of fully integrated jacketed cavities with high power coupler and tuner is crucial for the project. Such a characterization of jacketed cavity requires a horizontal test cryostat. Existing horizontal testing facilities at Fermilab, Horizontal Test Stand (HTS) and Spoke Test Cryostat (STC), are not large enough to accommodate jacketed 650 MHz 5-cell cavity. An upgrade of the STC is proposed to install extension to the cryostat and modify cryogenic connections and RF infrastructure to provide testing of 650 MHz cavities. In this paper we describe STC upgrade and commissioning of the upgraded facility. We discuss mitigation of issues and problems specific for testing of high Q₀ 650 MHz cavities, which require low residual magnetic field and low acoustic and mechanical vibrations environment.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP091

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP092

Status of Cryomodule Testing at CMTB for CW R&D

cryomodule, FEL, operation, linac

1129

J. Branlard, V. Ayvazyan, A. Bellandi, J. Eschke, C. Gümüş, D. Kostin, K.P. Przygoda, H. Schlarb, J.K. Sekutowicz
DESY, Hamburg, Germany

Cryo Module Test Bench (CMTB) is a facility to perform tests on European XFEL like superconducting accelerating modules. The 120 kW Inductive Output Tube (IOT) installed in the facility allows driving the eight superconducting cavities inside the module under test in a vector-sum or single cavity control fashion with average Continuous Wave (CW) gradients higher than 20 MV/m. The scope of these tests is to evaluate the feasibility of upgrading European XFEL to CW operation mode. Following the successful tests done on a prototype module XM-3 the initial performance results on the production module XM50 will be presented in this paper. Because of European XFEL requirements, XM50 is equipped with modified couplers that allow a variable Loaded Quality factor(QL) to values higher than 4x10⁷. A cost relevant open question is the maximum QL that can be reached while maintaining the system within the European XFEL field stability specifications of 0.01 % in amplitude and 0.01 deg in phase. Because of this, the LLRF system capability of rejecting microphonic and RF disturbances, as well as Lorentz Force Detuning (LFD) related effects in open and closed loop is of prime interest.

Poster THP092 [1.514 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP092

About •

paper received ※ 25 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP093

Upgrade on the Experimental Activities for ESS at the LASA Vertical Test Facility

radiation, diagnostics, electron, detector

1133

M. Bertucci, A. Bosotti, A. D’Ambros, P. Michelato, L. Monaco, C. Pagani, R. Paparella, D. Sertore
INFN/LASA, Segrate (MI), Italy

The LASA vertical test facility is equipped for the cold test of ESS medium-beta 704.42 MHz cavities, with and without He tank, and is integrated with several diagnostic tools allowing a careful analysis of cavity performance limitations. This paper reports the latest tests on ESS cavities - both prototypes and series - and a discussion on the experimental results. The recent instrumental upgrades implemented in the facility - and the ones foreseen for the future in view of a further improvement of cavity performances - are also pointed out.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP093

About •

paper received ※ 24 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP095

Direct Measurement of Thermoelectric Currents During Cool Down

simulation, experiment, niobium, coupling

1139

A.E. Ivanov, F. Gerigk, A. Macpherson
CERN, Geneva, Switzerland

In recent years there has been much discussion on thermoelectric effects and their role in flux expulsion during cool down of SRF cavities. Magnetic field is often measured to asses both flux expulsion as the cavity undergoes superconducting transition, and thermoelectric currents due to spatial thermal gradients. As a complementary view, in this paper we show direct measurement of the thermoelectric current independent from the expulsion measurement of the magnetic field. In our setup the azimuthally symmetric cavity is vertically installed and the thermal gradient is along the symmetry axis allowing to describe the cool down behavior of the thermoelectric current using simple coupled simulations.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP095

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP096

ESS Prototype Cavities Developed at CEA Saclay

SRF, niobium, HOM, linac

1143

E. Cenni
CEA-IRFU, Gif-sur-Yvette, France
M. Baudrier, P. Carbonnier, G. Devanz, X. Hanus, L. Maurice, J. Plouin, D. Roudier, P. Sahuquet
CEA-DRF-IRFU, France

The ESS elliptical superconducting Linac consists of two types of 704.42 MHz cavities, medium and high beta, to accelerate the beam from 216 MeV up to the final energy at 2 GeV. The medium and high-beta parts of the Linac are composed of 36 and 84 elliptical cavities, with geometrical beta values of 0.67 and 0.86 respectively. CEA Saclay is in charge of the cavity prototypes that is designing, manufacturing, testing and integrating them into demonstrator cryomodules. We have manufactured 6 medium beta and 5 high beta cavities and we present here the latest results concerning these activities.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP096

About •

paper received ※ 22 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP097

Field Emission Studies on ESS Elliptical Prototype Cavities at CEA Saclay

cryomodule, electron, radiation, detector

1147

E. Cenni, M. Baudrier, G. Devanz, L. Maurice, O. Piquet, D. Roudier
CEA-DRF-IRFU, France

CEA Saclay is in charge of the cavity prototypes that is designing, manufacturing, testing and integrating them into demonstrator cryomodules. We have manufactured 6 medium beta and 5 high beta cavities. As part of these activities we are interested in field emission as one of the limiting factors for cavity performances. We are currently collecting data from cavities operated in vertical cryostat and inside cryomodules. Analysis are carried out by means of particle tracking simulation and comparison with radiation dose monitor and scintillators.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP097

About •

paper received ※ 27 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP099

The ESS Database for Elliptical Cavities

database, HOM, SRF, cryomodule

1152

P. Pierini, C.G. Maiano
ESS, Lund, Sweden
A. Bosotti, D. Sertore
INFN/LASA, Segrate (MI), Italy
E. Cenni
CEA-IRFU, Gif-sur-Yvette, France
M. Wang
IHEP, Beijing, People’s Republic of China

The large inkind scope of the elliptical superconducting RF linac of the ESS facility implies the handling of handover conditions between the cavities fabrication and testing phases performed at INFN and STFC, to the assembly of cryomodules at CEA and later to ESS in Lund. The performance qualification at the module test stand, and later the commissioning and operation phases require the availability of the cavity performance and frequency data under all environmental conditions during preparation (e.g. temperature, vacuum in beam line/He vessel/vacuum vessel, tuner state). Availability of the data needs to be guaranteed for the long term maintainability of the accelerator. For these reasons a cavity database has been set up at ESS, integrating the data contained in the handover documentation from the inkind partners and extending it during the activities at ESS after receiving the modules. The database has been used to analyze the preparation steps of the prototype demonstrator cryomodule for the tests at ESS, by benchmarking with the data collected during the tests at CEA, and is currently used during the series cavities handover phases.

Poster THP099 [10.434 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP099

About •

paper received ※ 03 July 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP100

Insight into DESY’s Test Laboratory for Niobium Raw Material and Semi-finished Products

niobium, FEL, SRF, controls

1157

J.I. Iversen, A. Brinkmann, A. Ermakov, A. Muhs, J. Ziegler
DESY, Hamburg, Germany

DESY has started setting up a test laboratory for niobium more than 20 years ago. The initial application was to assure required surface quality of niobium sheets before its forming to half cells for the 1.3 GHz SRF Tesla shape cavities. As a first test equipment DESY developed a basic eddy current test device which was refined continuously. Since that time the laboratory grew with the requirements on R&D activities for niobium raw material and its semi-finished products. To be able to assure the Quality of niobium products needed for the European XFEL series cavity production, the Lab¿s infrastructure was updated significantly. Now the capabilities of the test laboratory cover the investigation of the fundamental physical properties of various materials including for example mechanical properties, surface, microstructure and chemical composition analysis. The Quality Assurance for the European XFEL was performed successfully on an outstanding level and in the meantime the laboratory was used for several other projects like LCLS-II and ESS. We present DESY’s test infrastructure as well as applied methods for the Quality Assurance and R&D activities and we report about experiences.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP100

About •

paper received ※ 25 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP101

Commissioning of a Cleanroom for SRF Activities at the Helmholtz Institute Mainz

vacuum, SRF, operation, heavy-ion

1162

T. Kürzeder, K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, R.G. Heine, S. Lauber, J. List, M. Miski-Oglu
HIM, Mainz, Germany
K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, S. Lauber, J. List, M. Miski-Oglu, S. Yaramyshev
GSI, Darmstadt, Germany
K. Aulenbacher, F.D. Dziuba, S. Lauber
IKP, Mainz, Germany
J. Conrad
TU Darmstadt, Darmstadt, Germany
R.G. Heine, F. Hug, J. List, T. Stengler
KPH, Mainz, Germany

A newly built cleanroom is under commissioning at the Helmholtz-Institute Mainz (HIM). In its ISO-class 6 area vacuum components and cavities can be cleaned in different ultrasonic baths and in a dedicated conductance rinsing bath. In the ISO-class 4 area a large vacuum oven offers the possibility for comprehensive drying. A high pressure rinsing cabinet (HPR) has been installed between the two cleanroom areas to be loaded and unloaded from both sides. Complete cold-strings have to be mounted in the ISO-class 4 area and to be rolled out of the cleanroom on a rail system installed on the floor. All installations and tools have been integrated to treat and assemble superconducting 217 MHz multigap crossbar cavities for the Helmholtz Linear Accelerator (HELIAC), which is under development by HIM and GSI. Those crossbar cavities have a diameter of 650 mm and a weight of up to 100 kg. The cleanroom will be also used for the Mainz Energy-Recovering Superconducting Accelerator (MESA) project, processing the TESLA/XFEL type 9-cell cavities and other beamline components. This paper reports on the commissioning of the cleanroom and shows the features of the different installations.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP101

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP102

Uncertainty Quantification of a Quadrupole-Resonator for Radio Frequency Characterization of Superconductors

quadrupole, HOM, SRF, radio-frequency

1168

P. Putek, S. Gorgi Zadeh, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
W. Hillert
ELSA, Bonn, Germany
W. Hillert, M. Wenskat
University of Hamburg, Institut für Experimentalphysik, Hamburg, Germany
M. Wenskat
DESY, Hamburg, Germany
U. van Rienen
University of Rostock, Rostock, Germany

Funding: This work has been supported by the German Federal Ministry for Research and Education BMBF under contract 05H18HRRB1.
To explore the fundamental properties of superconducting materials used in modern particle accelerators, high precision surface resistance measurements in a dedicated testing equipment is of key importance. The quadrupole resonator, originally developed at CERN, and then successfully modified at the Helmholtz-Zentrum Berlin, is ideally suited for characterization of samples at temperatures of 1.8 K to > 20 K, RF fields of up to 120 mT and frequencies of 433 MHz, 866 MHz and 1.3 GHz. In the past years, this set-up has been subject of intensive research on both its capabilities and limitations. Yet, one of the main challenges is the accuracy of the surface resistance measurement, which is determined by both the uncertainty in the RF measurement and manufacturing imperfections related to the production tolerances such as quenching and chemical polishing processes, etc. In this contribution, we focus on the influence of key geometrical parameters on operating the quadrupole resonator at the third mode, since the surface resistance measurement shows some unexpected behavior for this frequency.
* Design and Fabrication of a Quadrupole-Resonator for Sample R&D by M. Wenskat, W. Hillert, et al.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP102

About •

paper received ※ 25 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP103

Reconstruction of the Longitudinal Phase Space for the Superconducting CW HELIAC

heavy-ion, emittance, linac, proton

1173

S. Lauber, K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, T. Kürzeder, J. List, M. Miski-Oglu
HIM, Mainz, Germany
K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, P. Forck, V. Gettmann, M. Heilmann, T. Kürzeder, S. Lauber, J. List, M. Miski-Oglu, T. Sieber, S. Yaramyshev
GSI, Darmstadt, Germany
K. Aulenbacher, F.D. Dziuba, S. Lauber
IKP, Mainz, Germany
H. Podlech, M. Schwarz
IAP, Frankfurt am Main, Germany

The superconducting (SC) heavy ion HElmholtz LInear ACcelerator (HELIAC) is under development at GSI in Darmstadt in cooperation with Helmholtz Institute Mainz (HIM) and Goethe-University Frankfurt (GUF). A novel design is used for the accelerating cavities, namely SC continuous wave (CW) multigap Crossbar H-Mode cavities. For this a dedicated beam dynamics layout - the EQUidistant mUltigap Structure (EQUUS) - has been carried out a couple of years ago and is under further development. In December 2018 the GSI High Charge State Injector (HLI) delivered heavy ion beam to the already commissioned first of series superconducting RF cavity. Proper 6D-matching to the CH cavity demands sufficient beam characterisation. Slit-grid emittance measurements provided for the transverse phase space determination. By measuring the longitudinal projection of the bunch with a Feschenko Monitor (Beam Shape Monitor), the bunch profile was obtained. With a dedicated algorithm, the full longitudinal phase space at the HLI-exit could be reconstructed from a set of BSM measurements. The basic reconstruction method, all relevant BSM measurements and the resulting phase space reconstruction will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP103

About •

paper received ※ 19 June 2019 paper accepted ※ 29 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP104

Numerical Estimation of Beam Break-Up Instability in TESLA Cavities

dipole, solenoid, linac, focusing

1178

V. Volkov, V.M. Petrov
BINP SB RAS, Novosibirsk, Russia

In this article the numerically estimated BBU instability behaviors of a 9 cell superconducting TESLA cavity are presented for first two pass-band trapped dipole modes (18 in all). The given BBU threshold current values are calculated by the method of beam energy gain averaging on phases of dipole mode fields. BBU instability behaviors in cases of applying the cavities in Linacs as well in Energy Recovery Linacs (ERLs) are considered. The BBU influence on beam emittance degradation is demonstrated. Examples for suppression of beam BBU oscillations by a solenoid focusing and applying of an external RF generator with a feedback are visualized.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP104

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP105

Thermal Mapping of SRF Cavities by Second Sound Detection With Transition Edge Sensors and Oscillating Superleak Transducers

SRF, diagnostics, experiment, luminosity

1182

G. Vandoni, T. Koettig, A. Macpherson, K. Turaj, L. Vega Cid
CERN, Meyrin, Switzerland
H. Furci
EPFL, Lausanne, Switzerland

The SRF cavity testing facilities at CERN include four vertical cryostat stations in SM18 and a cryostat for small cavities in the Cryolab. A large range of structures are tested, from Nb thin film cavities for HIE-Isolde and LHC, to bulk Nb crab cavities for HiLumi or 704 MHz 5-cell high-gradient cavities. To cope with different shapes and small series tests, thermal mapping diagnostics is deployed by sensing second sound in superfluid helium. A new type of Transition Edge Sensors (TES) has been developed in the last 2 years. These are miniature resistors of thin-film superconducting alloys, micro-produced on insulating wafers. An extensive campaign of optimization of design, fabrication process and composition was accompanied by qualification in a calibration cryostat. Reproducibility, stability, then intensity, distance and angular dependence of the response were assessed and compared to Oscillating Superleak Transducers (OST). The TES were then installed in a vertical cryostat for tests of a prototype crab cavity for HiLumi. TES are now applied to quench localization on high gradient cavities, for which the most recent results will be presented, together with the OST results.

Poster THP105 [2.186 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP105

About •

paper received ※ 23 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THP106

An SRF Test Stand in High Intensity and High Energy Proton Beams

cryogenics, cryomodule, vacuum, SRF

1187

G. Vandoni, K. Artoos, V. Baglin, K. Brodzinski, R. Calaga, O. Capatina, S.D. Claudet, L.P. Delprat, S. Mehanneche, E. Montesinos, C. Pasquino, J.S. Swieszek
CERN, Meyrin, Switzerland

In the framework of HL-LHC, a new infrastructure was installed in 2018, to test SRF structures in the proton beams of the SPS. Scope of the test stand is to study the operational performance of crab cavities for HL-LHC – more generally, SRF cavities – through a wide range of proton beam parameters up to high energy and current, under safe conditions for equipment and personnel. The SPS beam instrumentation is used to monitor orbit centering, RF phase scans, bunch rotation. To minimize impact on beam time, infrastructure and services allow for full remote control. Critical aperture restrictions is overcome by placing the test structure and its ancillaries on a motorized table for lateral translation in- and out of beam. Two articulated Y-shaped vacuum chambers connect the test cryomodule on a beam by-pass. A new cryogenic refrigerator is installed in a split scheme, with an underground cold box fed from a surface compressor. The two Inductive Output Tubes (IOT) power amplifiers deliver up to 60 kW cw via coaxial transmission lines to the two cavities and charges and circulators, the latter installed on the translation table. Interlocks and safety equipment complete the test stand.

Poster THP106 [3.982 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-THP106

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAA1

Overview of SRF Deflecting and Crabbing Cavities

HOM, cryomodule, collider, luminosity

1192

S.U. De Silva
ODU, Norfolk, Virginia, USA

Developments over the past few years on novel superconducting deflecting and crabbing cavities have introduced advanced rf geometries with improved performance, in comparison to the typical squashed elliptical cavities operating in TM110 type mode. These new structures are compact geometries operating in either TEM type or TE11-like mode. One of the key applications of such cavities is the use of crabbing systems for circular colliders in increasing the luminosity. Crabbing systems are an essential component in future colliders with intense beams and proposed electron-ion colliders. High luminosity upgrade of LHC is planned to implement crabbing systems at two interaction points. Recently, a two-cavity cryomodule with double quarter wave crabbing cavity was installed in SPS at CERN and successfully tested with the proton beam. We present the details of different superconducting deflecting and crabbing cavities and their applications, as well as the recent results of the crabbing systems test at SPS.

Slides FRCAA1 [14.149 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAA1

About •

paper received ※ 04 July 2019 paper accepted ※ 14 August 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAA3

Industrial Cavity Production: Lessons Learned to Push the Boundaries of Nitrogen-Doping

niobium, cryomodule, SRF, linac

1199

D. Gonnella, S. Aderhold, A. Burrill, M.C. Ross
SLAC, Menlo Park, California, USA
E. Daly, G.K. Davis, F. Marhauser, A.D. Palczewski, K.M. Wilson
JLab, Newport News, Virginia, USA
A. Grassellino, C.J. Grimm, T.N. Khabiboulline, O.S. Melnychuk, S. Posen, D.A. Sergatskov
Fermilab, Batavia, Illinois, USA

Funding: Work supported by US DOE Contract DE-AC02-76SF00515.
Nitrogen doping has been proven now in several labs to enhance Q₀ values of 1.3 GHz cavities in the gradient domain favored by CW operation. The choice of doping for the LCLS-II project has given the community a wealth of statistics and experience on the challenge of transferring the doping technology to industry. Overall, industry-produced nitrogen-doped cavities have shown excellent performance, however some technical issues have arisen. This talk focuses on lessons learned from the production of over 300 nitrogen-doped cavities for LCLS-II and how issues were mitigated to further improve performance. Finally, I will discuss pushing the boundaries of nitrogen-doping further by exploring different doping regimes in order to maintain excellent Q₀ performance, while reaching higher quench fields.

Slides FRCAA3 [16.880 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAA3

About •

paper received ※ 02 July 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAA4

Progress in SRF CH-Cavities for the HELIAC CW Linac at GSI

linac, heavy-ion, cryomodule, MMI

1206

M. Miski-Oglu, K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, T. Kürzeder, S. Lauber, J. List, S. Yaramyshev
HIM, Mainz, Germany
K. Aulenbacher, W.A. Barth, C. Burandt, F.D. Dziuba, V. Gettmann, M. Heilmann, T. Kürzeder, S. Lauber, J. List, A. Rubin, A. Schnase, S. Yaramyshev
GSI, Darmstadt, Germany
K. Aulenbacher, F.D. Dziuba, J. List
KPH, Mainz, Germany
M. Basten, M. Busch, T. Conrad, H. Podlech, M. Schwarz
IAP, Frankfurt am Main, Germany
S. Lauber
IKP, Mainz, Germany

The machine beam commissioning is a major milestone of the R&D for the superconducting heavy ion continuous wave linear accelerator HELIAC of Helmholtz Institute Mainz (HIM) and GSI developed in collaboration with IAP Goethe-University Frankfurt. During successful beam commissioning of the superconducting 15-gap Crossbar H-mode cavity at GSI Helmholtzzentrum für Schwerionenforschung heavy ions up to the design beam energy have been accelerated. The design acceleration gain of 3.5 MeV has been reached with full transmission for heavy ion beams of up to 1.5 particle mueA. We present fabrication experience and results of off-line and on-line cavity performance. The next step is the procurement and commissioning of so called ’Advanced Demonstrator’ - the first of series cryomodule for the entire accelerator HELIAC. Results of further Demonstrator beam tests, as well as the status of the Advanced demonstrator project will be reported.

Slides FRCAA4 [9.864 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAA4

About •

paper received ※ 23 June 2019 paper accepted ※ 02 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAA6

Investigation on 1, 3 and 9-Cell SRF Elliptical Cavities made of Large Grain Niobium

SRF, niobium, cryomodule, radio-frequency

1213

T. Dohmae, H. Inoue, T. Kubo, H. Shimizu, K. Umemori, Y. Watanabe, M. Yamanaka
KEK, Ibaraki, Japan

Large grain (LG) niobium is directly sliced from niobium ingot. LG niobium sheet has larger crystal size than that of fine grain (FG) niobium which is forged and rolled, and normally used as the SRF cavity materials. It is expected that higher Q-value can be achieved using LG niobium sheet. And, effective reduction in material cost can be also achieved by LG niobium since forge and rolling process are skipped. On the other hand, there are some difficulties in fabrication since it has large deformation due to strong anisotropy. Cavity fabrication facility in KEK has been fabricated 1, 3 and 9-cell elliptical cavities made by LG niobium and RF tested in vertical cryostat. In this talk, the fabrication process and test results from these cavities will be presented.

Slides FRCAA6 [5.819 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAA6

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAB3

The Design of an Automated High-Pressure Rinsing System for SRF Cavity and the Outlook for Future Automated Cleanroom on Strings Assembly

controls, SRF, linac, alignment

1216

H. Guo, Q.W. Chu, Y. He, C.L. Li, Y.K. Song, T. Tan, Z.M. You
IMP/CAS, Lanzhou, People’s Republic of China

High-pressure rinsing (HPR) and cavity assembly are two critical steps in cavity post-processing. Traditionally, high-pressure rinsing processing is based on ultra pure water system, pump, rinsing wand and simple-functional control system; cavity assembly processing is based on simple fixtures, wrenches, bolts and nuts. Beside the equipments, at least two operators are required in either of these two processing. Operators and their actions could bring mistakes and cause extra airborne particle contamination in cleanroom. To avoid the risk from labors, a robot has been introduced in IMP cleanroom for HPR assisting and assembly assisting. Labor cost and cavity RF test results are compared between the circumstances with and without robot assisting. In this work, an automated HPR system that has been designed and will be installed in IMP cleanroom will be presented. In addition, a future automated cleanroom on strings assembly will be discussed as well.

Slides FRCAB3 [6.203 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAB3

About •

paper received ※ 03 July 2019 paper accepted ※ 12 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAB4

Development of High Intensity, High Brightness, CW SRF Gun with Bi-Alkali Photocathode

cathode, gun, SRF, target

1219

T. Konomi, Y. Honda, E. Kako, Y. Kobayashi, S. Michizono, T. Miyajima, H. Sakai, K. Umemori, S. Yamaguchi
KEK, Ibaraki, Japan

Superconducting conduction electron guns can realize high acceleration voltage and high beam repetition. KEK has been developing the 1.3 GHz elliptical type 1.5 cell superconducting RF gun to investigate fundamental performance. The surface cleaning methods and tools were developed by using KEK SRF gun cavity #1 and surface peak electric field reached to 75 MV/m without field emission. We will apply this technique to the SRF gun cavity #2 for beam operation. The gun cavity #2 equips the helium jacket, frequency tuner cathode position adjuster to operate the electron beam. The RF structure was designed based on the gun cavity #1. The cathode rod is made of Nb. The photocathode deposited on the cathode rod will be cool down to 2K to minimize thermal emittance. The fabrication of the gun cavity #2 and helium jacket were completed. 4 times vertical tests were carried out. We will report the vertical test results and preparation of the horizontal test.

Slides FRCAB4 [10.826 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAB4

About •

paper received ※ 23 June 2019 paper accepted ※ 03 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAB5

Performance of 112 MHz SRF Gun at BNL

gun, cathode, electron, SRF

1223

T. Xin, I. Ben-Zvi, J.C. Brutus, C. Folz, T. Hayes, P. Inacker, Y.C. Jing, D. Kayran, V. Litvinenko, J. Ma, G.J. Mahler, M. Mapes, K. Mernick, T.A. Miller, G. Narayan, P. Orfin, I. Pinayev, S. Polizzo, T. Rao, F. Severino, J. Skaritka, K.S. Smith, R. Than, J.E. Tuozzolo, E. Wang, G. Wang, Q. Wu, B.P. Xiao, W. Xu, A. Zaltsman
BNL, Upton, New York, USA
S.A. Belomestnykh
Fermilab, Batavia, Illinois, USA
C.H. Boulware, T.L. Grimm
Niowave, Inc., Lansing, Michigan, USA
K. Mihara
Stony Brook University, Stony Brook, USA
I. Petrushina
SUNY SB, Stony Brook, New York, USA
K. Shih
SBU, Stony Brook, New York, USA

Funding: This work is funded by the DOE FOA (No. DE-FOA-0000632) and National Science Foundation (Award No. PHY-1415252).
A 112 MHz SRF electron photoinjector (gun) was developed at Brookhaven National Laboratory to produce high-brightness and high-bunch-charge bunches for the coherent electron cooling proof-of-principle experiment. The gun is designed to deliver electrons with a kinetic energy of up to 2 MeV. Electrons are generated by illuminating a high quantum efficiency (QE) K2CsSb photoemission layer with a green laser operating at a wavelength of 532 nm. The gun was able to generating 3 nC bunches at 1.7 MeV. The design goals, fabrication, performance and operational experience are reported here.

Slides FRCAB5 [3.984 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAB5

About •

paper received ※ 22 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAB6

The Effect of Helium Processing and Plasma Cleaning for Low Beta HWR Cavity

plasma, experiment, SRF, ion-effects

1228

S.C. Huang, Q.W. Chu, Y. He, C.L. Li, A.D. Wu, S.X. Zhang
IMP/CAS, Lanzhou, People’s Republic of China

The commissioning of the 25 MeV high power and high intensity proton Linac demo for CiADS showed that the performance of the SRF cavities was mainly limited by field emission inside the cavities. Therefore, the techniques of helium processing and reactive oxygen plasma cleaning have been developed to mitigate field emission issues. We performed an experiment with a low beta HWR cavity exposed to air directly and processed by helium and reactive oxygen. In this paper, the details of the experiment will be described, the efficiency of helium processing and plasma cleaning will be compared and discussed

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAB6

About •

paper received ※ 23 June 2019 paper accepted ※ 01 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAB7

Plasma Processing to Reduce Field Emission in LCLS-II 1.3 GHz SRF Cavities

plasma, radiation, vacuum, HOM

1231

B. Giaccone, J. Zasadzinski
IIT, Chicago, Illinois, USA
P. Berrutti, B. Giaccone, A. Grassellino, M. Martinello
Fermilab, Batavia, Illinois, USA
M. Doleans
ORNL, Oak Ridge, Tennessee, USA
D. Gonnella, G. Lanza, M.C. Ross
SLAC, Menlo Park, California, USA

Plasma cleaning for LCLS-II 9-cell 1.3 GHz cavities is under study at Fermilab. Starting from ORNL method, we have developed a new technique for plasma ignition using HOMs. Plasma processing is being applied to contaminated and field emitting cavities, here are discussed the first results in terms of Q and radiation vs E measured before and after treatment. Further studies are ongoing to optimize plasma parameters and to acquire statistics on plasma cleaning effectiveness.

Slides FRCAB7 [14.701 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAB7

About •

paper received ※ 23 June 2019 paper accepted ※ 04 July 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRCAB8

Systematic Studies of the Second Sound Method for Quench Detection of Superconducting Radio Frequency Cavities

simulation, radio-frequency, interface, diagnostics

1239

L. Steder, B. Bein, D. Reschke
DESY, Hamburg, Germany
W. Hillert
University of Hamburg, Institut für Experimentalphysik, Hamburg, Germany

DESY conducts R&D for SRF cavities, part of the manifold activities are vertical performance tests. Besides the determination of accelerating gradient and quality factor, additional sensors and diagnostic methods are used to obtain more information about the cavity behaviour and the test environment. The second sound system is a tool for spatially resolved quench detection via oscillating super-leak transducers, they record the second sound wave, generated by the quench of the superconducting Niobium. The mounting of the sensors was improved to reduce systematic uncertainties and results of a recent master thesis are presented in the following. Different reconstruction methods are used to determine the origin of the waves. The precision, constraints and limits of these are compared. To introduce an external reference and to qualify the different methods a calibration tool was used. It injects short heat pulses to resistors at exact known space and time coordinates. Results obtained by the different algorithms and measurements with the calibration tool are presented with an emphasis on the possible spatial resolution and the estimation of systematic uncertainties of the methods.

Slides FRCAB8 [3.039 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2019-FRCAB8

About •

paper received ※ 21 June 2019 paper accepted ※ 30 June 2019 issue date ※ 14 August 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)