A   B   C   D   E   F   G   H   I   K   L   M   N   O   P   Q   R   S   T   U   V   W    

acceleration

          
Paper Title Other Keywords Page
MOOCH02 First Full Beam Loading Operation with the CTF3 Linac linac, beam-loading, gun, instrumentation 39
 
  • R. Corsini, H.-H. Braun, G. Carron, O. Forstner, G. Geschonke, E. Jensen, L. Rinolfi, D. Schulte, F. Tecker, L. Thorndahl
    CERN, Geneva
  • M. Bernard, G. Bienvenu, T. Garvey, R. Roux
    LAL, Orsay
  • A. Ferrari
    Uppsala University, Uppsala
  • L. Groening
    GSI, Darmstadt
  • R.F. Koontz, R.H. Miller, R.D. Ruth, A.D. Yeremian
    SLAC, Menlo Park, California
  • T. Lefevre
    NU, Evanston
  The aim of the CLIC Study is to investigate the feasibility of a high luminosity, multi-TeV linear e+e- collider. CLIC is based on a two-beam method, in which a high current drive beam is decelerated to produce 30 GHz RF power needed for high-gradient acceleration of the main beam running parallel to it. To demonstrate the outstanding feasibility issues of the scheme a new CLIC Test Facility, CTF3, is being constructed at CERN by an international collaboration. In its final configuration CTF3 will consist of a 150 MeV drive beam linac followed by a 42 m long delay loop and an 84 m combiner ring. The installation will include a 30 GHz high power test stand, a representative CLIC module and a test decelerator. The first part of the linac was installed and commissioned with beam in 2003. The first issue addressed was the generation and acceleration of a high-current drive beam in the "full beam loading" condition where RF power is converted into beam power with an efficiency of more than 90%. The full beam loading operation was successfully demonstrated with the nominal beam current of 3.5 A. A variety of beam measurements have been performed, showing good agreement with expectations.  
Video of talk
Transparencies
 
MOPLT001 Acceleration of Electrons by Spatially Modulated Laser Wave electron, laser, vacuum, injection 527
 
  • R.A. Melikian, M.L. Petrosyan, V.S. Pogosyan
    YerPhI, Yerevan
  We study the acceleration of electrons in a system of linearly polarized laser wave, propagating at small angles to the direction of electron motion. The parameters of electron bunch and laser wave are chosen so, that during driving electrons in a band of a wave, the electric field of a wave has not changed the direction. The requirements of deriving of maximum rate of acceleration are found depending on parameters of electronic bunch and laser wave. It is shown, that the dependence of growth of electrons energy from number of light bands has nonlinear character. The influence of light diffraction on process of acceleration is considered. It is shown, that the discussed scheme of acceleration allows a possibility of deriving of high acceleration rate owing to existence of modern powerful lasers.  
 
MOPLT007 Base Line Design for a Beta-beam Neutrino Facility ion, linac, injection, target 542
 
  • M. Benedikt, S. Hancock, M. Lindroos
    CERN, Geneva
  The term beta-beam has been coined for the production of pure beams of electron neutrinos or their antiparticles through the decay of radioactive ions circulating in a storage ring. The neutrino source itself consists of a high energy storage ring (gamma ~150), with long straight sections in line with the experiment(s). The radioactive ions (6He and 18Ne) will be produced in an ISOL type target system. Due to the short life times of around 1s at rest, the beam needs to be accelerated as quickly as possible. For this a staged system of accelerators is proposed. The chain starts with a linac followed by a rapid cycling synchrotron for acceleration up to ~300 MeV/u. For further acceleration the existing PS and SPS machines are used. Finally, after acceleration to SPS top energy, the ions are transferred to the decay ring where they are merged with the already circulating bunch through a longitudinal stacking procedure. The base line design of the beta beam facility will be presented and the major design problems encountered as well possible solutions will be discussed.  
 
MOPLT023 Electron Model of an FFAG Muon Accelerator lattice, resonance, electron, simulation 587
 
  • E. Keil
    CERN, Geneva
  • J.S. Berg
    BNL, Upton, Long Island, New York
  • A. Sessler
    LBNL, Berkeley, California
  Parameters are derived for the lattice and RF system of electron models of a non-scaling FFAG ring for accelerating muons. The models accelerate electrons from about 10 to about 20 MeV, and have circumferences between 10 and 17 m. Magnet types and dimensions, spacings, half apertures, about 12~mm by 20~mm,and number of cells are presented. The magnetic components are compared to existing magnets. The tune variation with momentum covers several integers, similar to that in a full machine, and allows the study of resonance crossing. The consequences of misaligned magnets are studied by simulation. The lattices are designed such that transition is at about 15 MeV. The variation of orbit length with momentum is less than 36~mm, and allows the study of acceleration outside a bucket. A 100~mm straight section, in each of the cells, is adequately long for an RF cavity operating at 3 GHz. Hamiltonian dynamics in longitudinal phase space close to transition is used to calculate the accelerating voltage needed. Acceleration is studied by simulation. Practical RF system design issues, e.g. RF power, and beam loading are estimated.  
 
MOPLT061 Design Study for Advanced Acceleration Experiments and Monochromatic X-ray Production @ SPARC laser, electron, photon, plasma 695
 
  • L. Serafini, S. Cialdi, R. Pozzoli, M. Romé
    INFN-Milano, Milano
  • D. Alesini, S. Bertolucci, M.E. Biagini, C. Biscari, R. Boni, M. Boscolo, M. Castellano, A. Clozza, G. Di Pirro, A. Drago, A. Esposito, M. Ferrario, V. Fusco, A. Gallo, A. Ghigo, S. Guiducci, M. Incurvati, C. Ligi, F. Marcellini, M.  Migliorati, C. Milardi, L. Palumbo, L. Pellegrino, M.A. Preger, P. Raimondi, R. Ricci, C. Sanelli, M. Serio, F. Sgamma, B. Spataro, A. Stecchi, A. Stella, F. Tazzioli, C. Vaccarezza, M. Vescovi, C. Vicario, M. Zobov
    INFN/LNF, Frascati (Roma)
  • F. Alessandria, A. Bacci, F. Broggi, C. De Martinis, D. Giove, M. Mauri
    INFN/LASA, Segrate (MI)
  • R. Bonifacio, I. Boscolo, C. Maroli, V. Petrillo, N. Piovella
    Universita' degli Studi di Milano, MILANO
  • A. Mostacci
    Rome University La Sapienza, Roma
  We present a design study for an upgrade of the SPARC photo-injector system, whose main aim is the construction of an advanced beam test facility for conducting experiments on high gradient plasma acceleration and for the generation of monochromatic X-ray beams to be used in advanced medical applications and condensed matter physics studies. Main components of the proposed plan of upgrade are: two additional beam lines with interaction regions for synchronized high brightness electron and high intensity photon beams and the upgrade of the SPARC Ti:Sa laser system to reach a multi-TW power level (in excess of 1 J in pulse energy). Results of numerical simulations modeling the interaction of the SPARC electron beam and the counter-propagating laser beam are presented with detailed discussion of the monochromatic X-ray beam spectra generated by Compton backscattering: X-ray energies are tunable in the range 20 to 500 keV, with pulse duration from sub-ps to 30 ps. Preliminary simulations of plasma acceleration of the SPARC electron beam, generated in ultra-short bunches, via the LWF mechanism and with external injection are also shown: experiments of self-injection are also foreseen and illustrated.  
 
MOPLT066 Induction Accelerating Cavity for a Circular Ring Accelerator induction, synchrotron, proton, linac 704
 
  • K. Torikai, Y.A. Arakida, T. Kono, K. Koseki, E. Nakamura, Y. Shimosaki, K. Takayama, T. Toyama, M. Wake
    KEK, Ibaraki
  • J. Kishiro
    JAERI/LINAC, Ibaraki-ken
  This paper reports details of an induction accelerating cavity employed for induction synchrotron POP experiments [*] using the KEK 12GeV PS. This cavity is the first induction cavity in the history of accelerator that is used in a circular ring. We focus our attention on crucial aspects distinguished from well-know properties of RF cavity. The single cavity is capable of generating an acceleration voltage of 2.5kV with a pulse width of 250ns, which is operated at a repetition　rate in the range of 667kHz - 882kHz. The cavity is driven by its own pulse modulator through a 25m long transmission cable of 125W, the end of which is connected with a matching resistance so as to minimize reflection in a wide range of frequency. Accelerating field characteristics are discussed and matching features of the cavity as a one-to-one transformer are presented. A longitudinal and transverse coupling impedance have been measured using a net-work analyzer.

* K.Takayama et al., 'POP Experiments of the Induction Synchrotron' in this conference

 
 
MOPLT073 Picosecond High Voltage Switching for Pulsed DC Acceleration laser, electron, plasma, pulsed-power 722
 
  • J. Hendriks, G.J.H. Brussaard
    TUE, Eindhoven
  Laser wakefield acceleration promises the production of high energy electrons from table-top accelerators. External injection of a (low energy) electron bunch into a laser wakefield requires acceleration gradients of the order GV/m. In principle DC acceleration can achieve GV/m acceleration gradients. If high voltage pulses of the order MV can be switched with picosecond precision, the performance of such an accelerator would be greatly enhanced and even multistage DC acceleration would become feasible. Presently risetime and jitter of high voltage pulses in high voltage laser triggered spark gaps are limited to the nanosecond regime by the initial stochastic breakdown process in the gap. A way to overcome this limitation is to create a line focus between the electrodes with an intensity above 1018 W/m2 using a high power femtosecond Ti:Sapphire laser. Because of the instantaneous ionization and high degree of ionization in the plasma channel, picosecond switching precision can be achieved and jitter is reduced significantly. A spark gap test setup with 3 mm interelectrode distance has been build and the first measurements have been done. Femtosecond diagnostics for characterization of the laser induced plasma and electro-optic diagnostics for the high voltage pulse have been developed.  
 
MOPLT075 Ideal Waterbag Electron Bunches from an RF Photogun electron, emittance, cathode, simulation 725
 
  • O.J. Luiten, M.J. Van der Wiel, S.B. van der Geer
    TUE, Eindhoven
  • F. Kiewiet
    FOM Rijnhuizen, Nieuwegein
  • M.J. de Loos
    PP, Soest
  With the implementation of fs mode-locked Ti:Sapphire lasers in high-gradient RF photoguns, a new charged particle acceleration regime has emerged, the so-called pancake regime. Pancake bunches have by definition a restframe length which is much smaller than the bunch radius. This geometry allows a relatively simple, but effective analytical description of the space-charge dominated, critical initial part of the acceleration trajectory. In high-gradient RF photoguns the pancake regime can be relevant up to several MeV. The general opinion is that extremely short bunches should be avoided during the initial stages of the acceleration process, because high space charge densities are always detrimental to the final beam quality. We show that this is not necessarily true: shorter bunches may even lead to better beams.  
 
MOPLT081 Low Energy Ion Beam Dynamics in Axisymmetric RF Undulator Linac focusing, linac, ion, undulator 731
 
  • E.S. Masunov, S.M. Polozov
    MEPhI, Moscow
  The ion beam focusing and acceleration in an axisymmetric periodic RF undulator structure is considered. There is suggested that RF field has no a synchronous wave and accelerating force is to be driven by a combination of two non-synchronous waves. The influence of non-synchronous harmonics on ion beam dynamics is studied by means of a smooth approximation. Choice and optimization of RF field harmonics are made to obtain maximal transmission coefficient. The result is verified by a numerical simulation. The comparison with a conventional RF linac, where a synchronous harmonic accelerates a beam and non-synchronous one is focusing a beam, is described. This comparison is suitable for demonstration of the capabilities of an undulator linac.  
 
MOPLT088 Experimental Plasma Wake-field Acceleration Project at the VEPP-5 Injection Complex plasma, electron, injection, positron 740
 
  • A.V. Petrenko, A. Burdakov, A.M. Kudryavtsev, P.V. Logatchev, K.V. Lotov, A.N. Skrinsky
    BINP SB RAS, Novosibirsk
  The project of an experimental facility based on the VEPP-5 injection complex is described. Due to a good quality of electron or positron beams and special beam preparation system, the facility opens several possibilities for studies of the plasma wakefield acceleration: high peak beam currents, arbitrary beam profiles, long term beam-plasma interaction (up to the full driver depletion), and precise beam diagnostics. Various wakefield regimes can be experimentally demonstrated and studied: the efficient blow-out regime with a low energy spread and high acceleration rate (up to several GeV per meter); multibunch regime; long bunch instabilities; beam self-organization in plasma; plasma lens. If successfully realized, this experiment becomes a solid argument for feasibility of a high-energy collider based upon the plasma wakefield acceleration.  
 
MOPLT101 Performances of the Beam Generated by Metal-Dielectric Cathodes in RF Electron Guns cathode, gun, electron, plasma 767
 
  • I.V. Khodak, I.V. Khodak, V.A. Kushnir
    NSC/KIPT, Kharkov
  The paper describes results of the experimental research of the metal-dielectric cathode operation in RF electron gun. Application of these cathodes permits RF guns to generate intense beams with nanosecond current pulse duration. Electron beam is extracted from plasma sheath developed during the surface vacuum flashover dielectric. Simulated and experimental parameters of the beam obtained at the single-cavity RF gun output are summarized in the paper. The beam formation and its interaction with microwave field of high strength are analyzed qualitatively. Results are compared with experimental results obtained before in the 1.5-cavity RF electron gun. First experimental results on electron beam generation by the RF gun with a ferroelectric cathode are discussed in the paper.  
 
MOPLT102 To the Problem of Wake-field Excitation for Advanced Accelerator Concept electron, radiation, plasma, laser 770
 
  • I.N. Onishchenko, V. Kiselev, A. Linnik, N. Onishchenko, G. Sotnikov
    NSC/KIPT, Kharkov
  • V. Ushkov
    RRC Kurchatov Institute, Moscow
  The advanced accelerator concept to use the wake-fields exited in dielectric by a sequence of electron bunches for high-gradient particle acceleration has been proposed and investigated in [*-***]. Two essential merits are being exploited. First of them [**] is the excitation by a regular sequence of electron bunches that allows superposing coherently the wake-fields excited by each bunch. The second one [***] concludes to multi-mode operation that leads to peaking of the resulting HF-field that is represented by a sequence of spikes of alternative signs with essentially higher amplitude comparatively to only principle mode excitation. The recent works performed in NSC/KIPT on theoretical studies, simulation, and experimental investigations of the wake-fields excitation by a train of 2 MeV electron bunches in a dielectric waveguide are presented. Transition and Cerenkov radiation excited by short bunches in a limited dielectric medium was theoretically investigated. The measurements of wake-fields output power and the electron energy spectrum were experimentally performed.

* W.Gai, P.Schoessow, B.Cole et al. Phys. Rev. Lett. 61, 2756 (1988) ** I.N.Onishchenko, V.A.Kiselev, G.V.Sotnikov et al. Proc. 1995 Particle Accelerator Conf., p. 782-3*** T.B.Zhang, J.L.Hirshfield, T.C.Marshall et al Proc. 1997 Particle Accelerator Conf., V.42, No.3, p.1341

 
 
MOPLT112 Optimizing Non-Scaling FFAG Lattices for Rapid Acceleration lattice, quadrupole, electron, factory 800
 
  • C. Johnstone
    Fermilab, Batavia, Illinois
  • S.R. Koscielniak
    TRIUMF, Vancouver
  A linear approach to fixed field acceleration was first proposed [*,**] and successfully developed to support the rapid and large-emittance acceleration of muons for a Neutrino Factory or Muon Collider. Lattices have evolved from a simple F0D0-cell base as first proposed to a slightly more complex layout that has been referred to as a triplet configuration. In this work a methodology is developed for optimizing nonscaling lattices which demonstrates that the appropriate description is minimum momentum compaction, alpha=(dL/L)/(dp/p). Further, the triplet configuration is not used conventionally as a focusing telescope, but rather its optics is shown to resemble that of a F0D0-cell. This methodology is then used to propose and compare lattices for muon acceleration. Specifically a 2.5-5, 5-10, and 10-20 GeV/c lattice is proposed for muon acceleration and also one for a small, 10-20 MeV/c electron prototype machine.

* C. Johnstone, "FFAG Non-scaling Lattice Design", talk, Proc 4th Int Conf on the Physics Potential and Development of the m+ m- Colliders, San Francisco, CA Dec.10-12, 1997, pgs 696-698** F. Mills, "Linear Orbit Recirculators", ibid, pgs 693-696

 
 
MOPLT158 Cost Optimization of Non-Scaling FFAG Lattices for Muon Acceleration lattice, closed-orbit, extraction, injection 902
 
  • J.S. Berg, R. Palmer
    BNL, Upton, Long Island, New York
  Fixed Field Alternating Gradient (FFAG) accelerators are a promising idea for reducing the cost of acceleration for muon accelerators as well as other machines. This paper presents an automated method for designing these machines to certain specifications, and uses that method to find a minimum cost design. The dependence of this minimum cost on various input parameters to the system is given. The impact of the result on an FFAG design for muon acceleration is discussed.  
 
MOPLT174 Electron Acceleration for e-RHIC with the Non-scaling FFAG electron, emittance, synchrotron, collider 932
 
  • D. Trbojevic, M. Blaskiewicz, E.D. Courant, J. Kewisch, T. Roser, A. Ruggiero, N. Tsoupas
    BNL, Upton, Long Island, New York
  A non-scaling FFAG lattice design to accelerate electrons from 3.2 to 10 GeV is described. This is one of the possible solutions for the future electron-ion collider (eRHIC) at Relativistic Heavy Ion Collier (RHIC) at Brookhaven National Laboratory (BNL). This e-RHIC proposal requires acceleration of the low emittance electrons up to energy of 10 GeV. To reduce a high cost of the full energy super-conducting linear accelerator an alternative approach with the FFAG is considered. The report describes the 1277 meters circumference non-scaling FFAG ring. The Courant-Snyder functions, orbit offsets, momentum compaction, and path length dependences on momentum during acceleration are presented.  
 
TUYACH01 Laser-acceleration and Laser-cooling for Ion Beams ion, proton, laser, target 54
 
  • M. Roth, A. Blazevic, E. Brambrink, M. Geissel
    TU Darmstadt, Darmstadt
  • P. Audebert
    LULI, Palaiseaux
  • M. Bussmann, D. Habs, U. Schramm, J. Schreiber
    LMU, München
  • R. Clarke, S. Karsch, D. Neely
    CCLRC/RAL, Chilton, Didcot, Oxon
  • J.A. Cobble, J. Fernandez, M. Hegelich, S. Letzring
    LANL, Los Alamos, New Mexico
  • T.E. Cowan, J. Fuchs, A. Kemp, H. Ruhl
    University of Nevada, Reno, Reno, Nevada
  • K. Ledingham, P. McKenna
    Strathclyde University, Glasgow
  The acceleration or cooling of particles with lasers has been the subject of growing interest over the last years. Because of the huge difference in mass, the acceleration of ions was so far limited to thermal expansion from laser plasmas, driven by the hot electron temperature. In recent years, due to the development of short-pulse ultra-intense lasers, the manipulation of ions has now become possible. Especially the generation of high quality, intense ion beams from laser solid interaction has attracted large attention and is investigated at many laboratories world-wide. For the first time, intense, directed, low emittance beams of ions have been observed, having several MeV of particle energy right from the source. A wealth of applications including next generation ion sources can be envisioned. The talk will give an overview of the status of laser cooling and ion acceleration including the last experimental results. In addition, an overview of the current and future research activities will be presented.  
Video of talk
Transparencies
 
TUZACH02 Ultra-high Gradient Compact Accelerator Developments plasma, laser, electron, injection 74
 
  • G.J.H. Brussaard, M.J. Van der Wiel
    TUE, Eindhoven
  Continued development of relatively compact, although not quite 'table-top', lasers with peak powers in the range up to 100 TW has enabled laser-plasma-based acceleration experiments with amazing gradients of up to 1 TV/m. In order to usefully apply such gradients to 'controlled' acceleration, various hurdles need to be overcome. The main one is that of well-synchronized injection into a sub-mm to micron wavelength plasma wave. The talk will describe the various physics regimes of laser wakefield acceleration, and the two classes of experiments being pursued. One is that of atmospheric-density plasmas, non-linear wakefields with extreme gradients (hundreds of GV/m)and 'internal injection' of few-femtosecond electron bunches. A second class involves modest-density plasmas,wakefields of order 1 GV/m and external injection of (sub)-ps bunches. The state-of-the-art of these experiments will be covered, including the progress on plasma waveguiding of TW pulses over many diffraction lengths. The talk will also provide an outlook for the coming few years. This part includes proposed schemes for improvements in the area of injection, such as 'all-optical' injection and injection based on GV/m 'pulsed-DC' photoguns.  
Video of talk
Transparencies
 
TUPKF013 Studies on Maximum RF Voltages in Ferrite-tuned Accelerating Cavities synchrotron, proton, ion, antiproton 985
 
  • K. Kaspar, H.G. Koenig, T. Winnefeld
    GSI, Darmstadt
  The GSI SIS100 project requires very high accelerating voltages. With ferrite-tuned synchrotron cavities the gap voltage is often strongly limited by the Q-loss effect appearing at medium dc bias fields. At low bias fields, considerably higher voltages can be reached, however. The maximum usable amplitudes over the bias region have been studied. At zero bias, the ferrites could be driven to more than a factor 3 above the Q-loss limit. Except overheating, no other problems appeared. With increasing bias, the maximum amplitudes decrease continuously to the Q-loss level. In this fall-off region there is still a tuning factor up to 2.5 available, with rf flux densities by at least a factor 2 above the Q-loss level. Measurements on small samples of the ferrite material used in the GSI cavities could be verified very well in a full-size cavity, for the most part. The tests were mainly limited by the available anode voltage and the fear of damaging the cavity. It seems possible, to generalize the main results for other ferrite materials, also. Based on the results, a possible scenario for the SIS100 rf system is given. Additionally, the results lead to an alternative cavity design for higher voltages, which is described as well.  
 
TUPKF015 Status of the Superconducting CH-Structure proton, ion, linac, simulation 991
 
  • H. Podlech, H. Deitinghoff, H. Klein, H. Liebermann, U. Ratzinger, A.C. Sauer, R. Tiede
    IAP, Frankfurt-am-Main
  H-mode cavities (IH-DTL, IH-RFQ, 4-Vane-RFQ) have been developed and operated successfully during the last decades for ion acceleration. At the IAP Frankfurt a new type of H-mode cavity, the CH-structure is under development. This multi cell drift tube cavity is operated in the TE21- mode. Due to its mechanical rigidity, room temperature as well as superconducting versions can be realized. Superconducting CH-structures might be used especially for cw operated linacs in nuclear research facilites and applied research projects like XADS or IFMIF. A superconducting 352 MHz CH-structure (beta=0.1) with 19 gaps will be available for first tests in 2004. We present the status of the cavity and of the new cryo laboratory in Frankfurt.  
 
TUPKF016 Dynamic Lorentz Force Detuning Studies in TESLA Cavities linac, resonance, coupling, beam-loading 994
 
  • V. Ayvazyan, S. Simrock
    DESY, Hamburg
  Dynamic detuning of the superconducting rf cavities due to Lorentz force induced mechanical excitation is a critical concern since the magnitude can approach the cavity bandwidth and require significant additional rf power for field control. In this paper, the influence of high accelerating fields on the resonance frequency in superconducting TESLA cavities is discussed. Cavities at the TESLA Test Facility have been operated at the design operating gradient close to 25 MV/m. It is shown that Lorentz force detuning constant factors are different for different cavities, significant spread have been observed.  
 
TUPKF024 Operation Experience with ALPI Nb/Cu Resonators ion, superconductivity, cathode 1018
 
  • A.M. Porcellato, L. Bertazzo, M. De Lazzari, D. Giora, V. Palmieri, S. Stark, F. Stivanello
    INFN/LNL, Legnaro, Padova
  The refurbishing, by replacing the Pb superconducting film by Nb, of ALPI QW accelerating resonators was completed in 2003. All the 52 cavities are now in operation showing a large increase in the average accelerating field, which exceeds 4.5 MV/m (21 MV/m pick electrical surface field). The performance of renewed resonators has been increasing with time reaching 6MV/m in the last produced units. The increase in ALPI performance and the advantage in conditioning and setting time obtained by the upgrading process will be reported.  
 
TUPKF035 RF System for Compact Medical Proton Synchrotron synchrotron, proton, impedance, radiation 1039
 
  • Z. Fang, K. Egawa, K. Endo, S. Yamanaka
    KEK, Ibaraki
  • Y. Cho, T. Fusato, T. Hirashima
    DKK, Kanagawa
  The rf system has been developed for the compact medical proton synchrotron. The rf system will be operated in pulse mode with the fundamental rf frequency sweeping from 1.6 to 15 MHz during the acceleration time of 5 ms. The required rf cavity voltage is a function of acceleration time too, with the voltage of fundamental varying from 13 to 6 kV. Besides, high order harmonics are also considered to apply to the rf system, and the cavity peak voltage varying from 20 to 9 kV during the acceleration time is expected. The performance of the rf system is being studied and will be presented.  
 
TUPKF037 Multi-harmonic RF Acceleration System for a Medical Proton Synchrotron synchrotron, feedback, proton, impedance 1045
 
  • K. Saito, M. Katane, K. Kobayashi, K. Masui, K. Moriyama, H. Nishiuchi, H. Sakurabata, H. Satomi
    Hitachi, Ltd., Power & Industrial Systems R&D Laboratory, Ibaraki-ken
  We have developed an RF accelerating system for medical proton synchrotron. The RF cavity is a tuning-free wideband type, loaded with FINEMET cores, which is driven by a solid-state RF power amplifier with operation frequency range between 1MHz and 10MHz. Multi-harmonic RF acceleration scheme has been realized with the RF control system, to reduce beam loss by space-charge effect in low energy region. The original techniques for high-speed digital signal processing and high-precision RF signal processing have been applied, in order to fulfill feedback control of the frequency, phase and amplitude of the second and third harmonic RF signals as well as the fundamental one.  
 
TUPKF067 High Power Magnicons at Decimeter Wavelength for Muon and Electron-Positron Colliders collider, gun, electron, linac 1099
 
  • O.A. Nezhevenko, V.P. Yakovlev
    Omega-P, Inc., New Haven, Connecticut
  • J.L. Hirshfield
    Yale University, Physics Department, New Haven, CT
  The CLIC drive linac requires pulsed RF amplifiers with a power of 50 MW at 937 MHz. In turn the muon collider requires 100 MW, 800 MHz RF amplifiers for the final stages of acceleration. In this paper conceptual designs of magnicons for these applications are presented. In addition to the typical magnicon advantages in power and efficiency, the designs offers substantially shorter tube length compared to either single- or multiple-beam klystrons.  
 
TUPKF079 A Low Noise RF Source for RHIC beam-losses, instrumentation, controls, luminosity 1123
 
  • T. Hayes
    BNL, Upton, Long Island, New York
  The Relativistic Heavy Ion Collider requires a low noise rf source to ensure that beam lifetime during a store is not limited by the rf system. The beam is particularly sensitive to noise from power line harmonics. Additionally, the rf source must be flexible enough to handle the frequency jump required for rebucketing (transferring bunches from the acceleration to the storage rf systems). This paper will describe the design of a Direct Digital Synthesizer (DDS) based system that provides both the noise performance and the flexibility required.

Work performed under the auspices of the US Department of Energy

 
 
TUPLT020 High Intensity Uranium Operation in SIS18 ion, injection, septum, beam-losses 1180
 
  • P.J. Spiller, K. Blasche, P. Hülsmann, A. Kraemer, H. Ramakers, H.R. Sprenger
    GSI, Darmstadt
  For the present experiment program and the planned international accelerator facility at GSI, the space charge limit of SIS18 for highly(4x1010) and intermediate (2.7x1011) charged uranium ions shall be reached within the next four years. Furthermore, measures to increase the repetition- and ramp rate up to 4 Hz with 10 T/s have been progressed. The present state of intensities per cycle and the limitations will be described. In connection with the planned enhancement of heavy ion intensities, protection, interlock and diagnostic systems, especially for the injection- and extraction devices have been prepared. Special attention is drawn on the insights which were achieved with respect to the operation at dynamic vacuum conditions. Results of R&D work with the goal to increase the intensity threshold and to improve the beam life time will be summarized. Furthermore, the specific upgrade program and schedule for the SIS18 booster mode will be presented.  
 
TUPLT044 Delta-T Procedure for Superconducting Linear Accelerator linac, pick-up, simulation, injection 1249
 
  • A. Bogdanov, R. Maier, Y. Senichev
    FZJ/IKP, Jülich
  Development of the tune-up procedure for a linear accelerator is the next important stage after the design is complete. Conventional delta-T procedure developed for tuning of a normal-conducting linear accelerator by Crandall allows setting up of accelerating field amplitude and phase in cavity with known phase velocity. However, application of the delta-T procedure to a superconducting linac meets some difficulties. In particular, the synchronous phase velocity in superconducting linac is determined by RF phase shift between cavities, but not by geometrical size of accelerating cells as in normal conducting linac. Additionally, in superconducting linac the smaller phase advance leads to an insensibility of particles at the cavity exit to the variation of the electric field inside the cavity. In the paper we consider the modified delta-T procedure adjusted for superconducting linac. Numerical simulations prove that by proposed technique both tasks of preservation of necessary stable region motion and providing the beam with required final energy can be successfully solved.  
 
TUPLT045 Separatrix Formalism Applied to Linacs Accelerating Particles with Different Charge to Mass Ratio linac, space-charge, proton, simulation 1252
 
  • A. Bogdanov, R. Maier, Y. Senichev
    FZJ/IKP, Jülich
  We have developed separatrix formalism for superconducting linear accelerators. This method allows optimizing the quasi-synchronous velocity behavior along a linac. It gives a great advantage in acceleration of particles with different charge to mass ratio. In the article design optimization of structure supposed to accelerate different particles is presented. As an example for numerical simulation superconducting injector COSY is taken.  
 
TUPLT052 GANIL Status Report ion, cyclotron, target, secondary-beams 1270
 
  • F. Chautard, J.L. Baelde, C. Barue, C. Berthe, A. Colombe, L. David, P. Dolegieviez, B. Jacquot, C. Jamet, P. Leherissier, R. Leroy, M.H. Moscatello, E. Petit, A. Savalle, G. Sénécal, F. Varenne
    GANIL, Caen
  The GANIL facility (Caen, France) is dedicated to the acceleration of heavy ion beams for nuclear physics, atomic physics, radiobiology and material irradiation. The production of radioactive ion beams for nuclear physics studies represents the main part of the activity. The in-flight fragmentation method was already used, since 1994, with the SISSI device. Since September 2001, SPIRAL, the Radioactive Ion Beam Facility at GANIL, delivers radioactive species produced by the ISOL method. The heavy ion beams of GANIL are sent onto a target and source assembly, and the radioactive beams are accelerated up to a maximum energy of 25 MeV/u by the cyclotron CIME. The operation and the running statistics of GANIL-SPIRAL are presented, with particular attention to the first SPIRAL beams. Few results about the cyclotron CIME, as the mass selection and tuning principle are summarized. The recent developments for increasing stable beams intensities, up to a factor 13 for argon, for use with SPIRAL, SISSI, or the LISE spectrometer, are presented. Considering the future of GANIL, SPIRAL II projects aims to produce high intensity secondary beams, by fission induced with a 5 mA deuteron beam in an uranium target.  
 
TUPLT072 Dual Harmonic Acceleration with Broadband MA Cavities in J-PARC RCS impedance, beam-loading, emittance, simulation 1318
 
  • M. Yamamoto
    JAERI, Chiba-ken
  • S. Anami, E. Ezura, K. Hara, Y. Hashimoto, C. Ohmori, A. Takagi, M. Yoshii
    KEK, Ibaraki
  • M. Nomura, A. Schnase, F. Tamura
    JAERI/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken
  In the J-PARC RCS rf system, since the fundamental rf acceleration voltage and the 2nd higher harmonic one are applied to each cavity, the impedance of hte cavity has a broadband characteristic. The Q-value of the cavity is chosen to make the higher harmonic beam loading effect as small as possible. The analysis of the amplifier and the beam loading effect on the dual harmonic rf system is described.  
 
TUPLT151 Status of the Fermilab Electron Cooling Project electron, recirculation, vacuum, antiproton 1485
 
  • J.R. Leibfritz, D.R. Broemmelsiek, A.V. Burov, K. Carlson, B. Kramper, T. Kroc, M. McGee, S. Nagaitsev, L. Nobrega, G. Saewert, C.W. Schmidt, A.V. Shemyakin, M. Sutherland, V. Tupikov, A. Warner
    Fermilab, Batavia, Illinois
  • G. Kazakevich
    BINP SB RAS, Novosibirsk
  • S. Seletsky
    Rochester University, Rochester, New York
  Fermilab has constructed and commissioned a full-scale prototype of a multi-MV electron cooling system to be installed in the 8.9 GeV/c Fermilab Recycler ring. This prototype was used to test all of the electron beam properties needed for cooling. However, because the prototype is not located within proximity of the Recycler ring, the actual electron cooling of antiprotons can not be demonstrated until it is relocated. The Fermilab electron cooling R&D project is scheduled to be completed in May, 2004 at which time it will be disassembled and relocated to a newly constructed facility where it will be installed in the Recycler. This paper describes the experimental results obtained with the prototype cooler system, gives an overview of the new electron cooling facility, and discusses the overall status of the project.  
 
WEOACH01 High Field Gradient Cavity for J-PARC 3 GeV RCS impedance, beam-loading, synchrotron, injection 123
 
  • C. Ohmori, S. Anami, E. Ezura, K. Hara, Y. Hashimoto, A. Takagi, M. Toda, M. Yoshii
    KEK, Ibaraki
  • M. Nomura, A. Schnase, F. Tamura, M. Yamamoto
    JAERI/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken
  A new type of rf cavity will be used for J-PARC project. To minimize the beam loading effects, the quality factor of the core stack is increased by a cut core configuration. High power test of the rf system has been performed. Temperature rise around the cut surface of the cores were observed. It is minimized by improving the cooling efficiency.  
Video of talk
Transparencies
 
WEODCH01 1.5-GeV FFAG Accelerator as Injector to the BNL-AGS injection, lattice, proton, linac 159
 
  • A. Ruggiero, M. Blaskiewicz, T. Roser, D. Trbojevic, N. Tsoupas, W. Zhang
    BNL, Upton, Long Island, New York
  A 1.5-GeV Fixed-Field Alternating-Gradient (FFAG) Accelerator has been recently proposed as a new injector to the Alternating-Gradient Synchrotron (AGS) of Brookhaven National Laboratory (BNL). It is being considered as a replacement of the present 1.5-GeV AGS Booster. The substitution will enhance the performance of the AGS accelerator facility in a variety of ways. It would still allow acceleration of all hadronic particles: protons, and heavy-ions. The major benefit is that it would considerably shorten the typical combined AGS acceleration cycle, and, consequently, may yield to an improvement of beam stability, intensity and size. The AGS-FFAG will also facilitate the proposed upgrade of the AGS facility toward a 1-MW average proton beam power. The paper describes a compact FFAG design for acceleration of protons from 200 MeV to 1.5 GeV. The circumference is about 250 m. The lattice is a periodic sequence of FDF triplets of combined-function magnets. An adjusted field profile has been calculated to compensate the variation of the main lattice functions with momentum. At injection, a beam pulse 130 μs long of negative-ions (H?) is stacked with the charge-exchange method. Acceleration of one pulse with 2.5 x 1013 protons takes about 130 μs, if harmonic-jump scheme is used in conjunction with the choice of 201.25 MHz. Four of such beam pulses are required to fill entirely the AGS. The entire filling process thus takes less than one millisecond.  
Video of talk
Transparencies
 
WEPKF075 Measurements of Sextupole Decay and Snapback in Tevatron Dipole Magnets injection, sextupole, dipole, superconductivity 1780
 
  • G. Velev, J. Annala, P. Bauer, J. DiMarco, H. Glass, R. Hanft, R. Kephart, M. Lamm, M. Martens, P. Schlabach, C. Sylvester, M. Tartaglia, J. Tompkins
    Fermilab, Batavia, Illinois
  To optimize the performance of the Fermilab Tevatron accelerator in Collider Run II, we have undertaken a systematic study of the drift and subsequent snapback of dipole magnet harmonics. The study has mostly focused on the dynamic behavior of the normal sextupole component, b2, as measured in a sample of spare Tevatron dipoles at the Fermilab Magnet Test Facility. We measured the dependence of the decay amplitude and the snapback time on Tevatron ramp parameters and magnet operational history. A series of beam studies was also performed [*]. This paper summarizes the magnetic measurement results and describes an optimization of the b2 correction scheme which is derived from these measurements.

* P.Bauer et al. These proceedings.

 
 
WEPLT014 Mechanical Dynamic Load of the LHC Arc Cryo-magnets during the LHC Installation monitoring, quadrupole, dipole, simulation 1849
 
  • O. Capatina, K. Artoos, G. Huet, B. Nicquevert
    CERN, Geneva
  About 1700 LHC main superconducting dipoles and quadrupoles will have to be transported and handled between the assembly, the magnet measurements and the storage that precedes the final installation in the LHC tunnel. To ensure the required mechanic and geometric integrity of the cryo-magnets, transport specifications and allowed acceleration loads were defined after detailed dynamic analysis. A large number of cryo-magnets are now arriving at CERN on a regular basis. The logistics for the handling and transport are monitored with tri-axial acceleration monitoring devices that are installed on each cryo-magnet. Measurements are made to commission new equipment like overhead cranes, tunnel transport and handling devices to guarantee that the defined acceleration limits are respected. The results from the acceleration monitoring that are stored in the same quality assurance system as the cryo-magnets allowed to give a first idea of the level of the mechanical dynamic load on each magnet throughout the logistics chain and were used to detect details such as out-of-specification accelerations that needed improvement.  
 
WEPLT015 Proposal for the Creation and Storage of Long Bunches in the LHC luminosity, emittance, injection, hadron 1852
 
  • H. Damerau, R. Garoby
    CERN, Geneva
  Long bunches with a uniform longitudinal line density held by barrier buckets are considered for a future luminosity upgrade of the Large Hadron Collider (LHC). With such bunches, the luminosity is maximised for a fixed number of particles. Instead of conventional barrier buckets, periodic barriers are proposed. These are generated with multiple RF harmonics (e.g. multiples of 40 MHz). A possible scheme to create and hold long flat bunches in the LHC is described, and the resulting gain in luminosity is estimated.  
 
WEPLT022 Transport and Installation of Cryo-magnets in CERN's Large Hadron Collider Tunnel factory, dipole, collider, hadron 1873
 
  • K. Kershaw, K. Artoos, O. Capatina, A.Y. Coin, M. Gielen, C. Hauviller
    CERN, Geneva
  The arcs of the Large Hadron Collider (LHC) will contain around 1700 main superconducting dipoles and quadrupoles. The long and heavy magnets are supported on fragile composite support posts inside a cryostat to reduce the heat in-leak to the magnets' super fluid helium bath. The presence of fragile components and the need to avoid geometry changes make the cryo-magnets very difficult to handle and transport. The transport and installation of the LHC cryo-magnets in the LEP tunnels originally designed for smaller, lighter LEP magnets has required development of completely new handling solutions. The paper explains the constraints imposed by the cryo-magnet characteristics, the existing tunnel infrastructure and schedule considerations. The development and realisation of transport and handling solutions are described, starting from conceptual design, through manufacture and testing to the installation of the first cryo-magnet. Integration studies to verify and reserve space needed for manoeuvre and the preparation of the infrastructure for transport and installation operations are also presented. The paper includes conclusions and some of the lessons learned.  
 
WEPLT056 An Electron Cooling System for the Proposed HESR Antiproton Storage Ring electron, antiproton, target, storage-ring 1969
 
  • M. Steck, K. Beckert, P. Beller, A. Dolinskii, B.  Franzke, F. Nolden
    GSI, Darmstadt
  • V.V. Parkhomchuk, V.B. Reva, A.N. Skrinsky, V.A. Vostrikov
    BINP SB RAS, Novosibirsk
  The HESR storage ring in the proposed new international accelerator facility will provide high quality antiproton beams for experiments with an internal target. In order to achieve the design luminosity for collisions with a hydrogen target powerful beam cooling is required. For dedicated experiments ultimate resolution is demanded. Therefore it is foreseen to provide cooled antiproton beams in the energy range 0.8-14 GeV with an energy spread of 100 keV or better. According to computer simulations the required cooling rates can be achieved by electron cooling with an electron current of 1 A. The conceptual design of an electron beam device which is based on electrostatic acceleration of the electrons and their transport in longitudinal magnetic fields into a cooling section with a strong magnetic field of up to 0.5 T will be presented. This design will allow cooling in the magnetized regime in order to reach the required high cooling rates. Some novel features for the generation and regulation of the accelerating voltage and for the beam transport are proposed.  
 
WEPLT110 Specific Beam Dynamics in Super-bunch Acceleration induction, synchrotron, emittance, simulation 2110
 
  • Y. Shimosaki, E. Nakamura, K. Takayama, T. Toyama
    KEK, Ibaraki
  • K. Horioka, M. Nakajima
    TIT, Yokohama
  • K. Koseki
    GUAS/AS, Ibaraki
  • K. Torikai
    Kyushu University, Fukuoka
  • M. Watanabe
    RIKEN, Saitama
  Proof-of-principle experiments on the induction synchrotron concept using the KEK 12-GeV PS makes progress, in which RF bunches and a super-bunch will be accelerated with a long step voltage generated in the induction accelerating gaps. In order to give a guide for super-bunch acceleration, the beam stabilities against a droop and a fluctuation of the accelerating voltage have been examined by using a simulation. The droop voltage gives an additional focusing or defocusing force in the longitudinal direction, which leads the mismatching beyond the transition energy. Furthermore, the extremely slow fluctuation of the accelerating voltage causes a lowest-order resonance near the transition. These induce a serious emittance blow-up in the longitudinal, so that the compensating manners will be presented. Moreover, the other issues such as head-tail instability and intra beam scattering will be discussed.  
 
WEPLT115 A Study of Transverse Resonance Crossing in FFAG resonance, simulation, beam-losses, emittance 2119
 
  • M. Aiba
    University of Tokyo, Tokyo
  • S. Machida, Y. Mori
    KEK, Ibaraki
  A study of "resonance crossing" in FFAG accelerator is described in this paper. A deviation of FFAG guiding field in actual magnet breaks zero chromaticity condition, and tunes cross resonance while acceleration. In order to avoid a critical beam loss or emittance growth, nominal tune should be chosen so as not to cross low-order resonances. However, crossing higher order resonance can be critical and that depends on the parameters such as crossing speed, excitation magnitude and initial beam emittance. We will present analytical model and simulation study in various parameter space.  
 
WEPLT118 Performance of the TU/e 2.6 Cell Rf-photogun in the 'Pancake' Regime plasma, simulation, space-charge, focusing 2128
 
  • S.B. van der Geer, G.J.H. Brussaard, O.J. Luiten, M.J. Van der Wiel
    TUE, Eindhoven
  • G. Pöplau
    Rostock University, Faculty of Engineering, Rostock
  • M.J. de Loos
    PP, Soest
  The 2.6 cell rf-photogun currently in operation at Eindhoven University of Technology has been designed as a booster for a 2 MeV semi-DC accelerator with a field of 1 GV/m. In this paper we present GPT simulation results of the TU/e gun, operated without its pre-accelerator, in the low-charge short-pulse regime. The main part of the paper describes detailed calculations of bunch lengthening due to path-length differences and space-charge effects, making use of high-precision field-maps and the newly developed 3D mesh-based space-charge model of GPT. It is shown that with the present set-up bunches can be produced that are well suited for injection into a planned experiment for controlled acceleration in a plasma-wakefield accelerator.  
 
WEPLT133 On Beam Dynamics Optimization rfq, controls, proton, electron 2152
 
  • D.A. Ovsyannikov, S.V. Merkuryev
    St. Petersburg State University, St. Petersburg
  Mathematical optimization methods are widely used in designing and construction of charged particle accelerators. In this paper new approach to beam dynamics optimization is considered. Suggested approach to the problem is based on the analytical representation for variation of examined functionals via solutions of special partial differentional equations. The problem of optimization is considered as a problem of mutual optimization chosen synchronous particle motion and charged particles beam at whole. This approach was applied to the beam dynamics optimization for RFQ structures.  
 
THPKF032 Cleaning of Parastic Bunches in the ESRF Booster Synchrotron for Time Structure Modes of Operation booster, injection, synchrotron, betatron 2341
 
  • E. Plouviez, N. Michel
    ESRF, Grenoble
  The ESRF injector booster accelerates electron bunches from 200 MeV to 6 GeV and inject them in a storage ring. It can accelerate a small number (1 to 5) of high charge bunches for the so called "time structure" filling mode operation of the SR. In this case we must avoid storing parasitic low charge bunches in the unused RF bucket of the SR. Until now this was achieved by a resonant knockout of these parasitic bunches on the beam stored in the SR. We have developed and implemented a system allowing the removal of these parasitic electrons during the acceleration in the booster, so that no extra cleaning is needed on the beam stored in the SR. This paper describes our setup and its key components, the tuning of the operating parameters of the system and presents the results achieved.  
 
THPKF038 Radiation Damage of Magnet Coils due to Synchrotron Radiation radiation, synchrotron, synchrotron-radiation, storage-ring 2359
 
  • K. Tsumaki, S. Matsui, M. Oishi, T. Yorita
    JASRI/SPring-8, Hyogo
  • T. Shibata, T. Tateishi
    KOBELCO, Hyogo
  Radiation damage of the equipment in the SPring-8 storage ring tunnel has become a serious problem. In the storage ring, the unnecessary radiation from bending magnets is shielded by absorbers. The equipment around the absorbers was damaged by the scattered radiation from the absorbers. Last year, cooling water leaked from the rubber hose of magnets. It was due to the deterioration of rubber hose caused by synchrotron radiation. We measured the radiation distribution around the storage ring and found that the most high intensity spot was on the magnet coil near the absorbers. If the coils are damaged and the magnets do not work correctly, we need to shut down the storage ring to exchange the magnet coils. To avoid such a situation, we needed to clarify the relation between the radiation damage of the coils and the dose of radiation. We did an acceleration test of the radiation damage of magnet coils. The magnet coils were exposed to the radiation from the bending magnet directly. We observed the degree of damage with changing the doses of radiation. In this paper, we describe about these acceleration tests and test results.  
 
THPLT004 Toroidal Cavity Loaded with an Electron Beam radiation, synchrotron, electromagnetic-fields, synchrotron-radiation 2463
 
  • E.D. Gazazyan, T. Harutyunyan, D.K. Kalantaryan
    YSU, Yerevan
  • V. Kocharyan
    DESY, Hamburg
  Three problems have been considered in this paper: the development of Maxwell's equations strict solution method to define the electromagnetic own values and own functions of the toroidal cavity; the radiation of the charged bunch rotating along the average radius, and, at last, the consideration of the case of a toroid filled with dielectric medium. The peculiarities of this radiation have been investigated as well. We suppose to consider the case when toroid is filled with plasma like a disperse medium.  
 
THPLT006 A Comparison of COSY DA Maps with Analytic Formulae for Orbit Functions of a Non-scaling FFAG Accelerator closed-orbit, electron, betatron, quadrupole 2469
 
  • S.R. Koscielniak
    TRIUMF, Vancouver
  Fixed Field Alternating Gradient (FFAG) magnetic lattices with fixed, possibly high, radio-frequency proposed for muon acceleration have unusual requirements: relative momentum swing dp/p of ± 30% and relative spread of revolution frequencies < 10(-3). It is not evident whether the existing accelerator optical design codes are sufficiently accurate for such a large momentum range. Analytic expressions for orbit displacements, tunes and path length have been derived for thick-element models of doublet, F0D0 and FDF triplet lattices; it is this paper's purpose to compare these with values computed by SYNCH and COSY, and truncated Taylor maps constructed by Lie algebra. The mutual agreement of results from independent sources will serve to validate them all. A mathematical necessity is that one at least of the magnets be of the combined-function type, and with entrance and exit faces disposed in a sector layout. It is sufficient to consider the triplet case because in the limit that the two F quadrupoles are combined, the cell reduces to the simpler F0D0. We use as our example a "nonscaling" FFAG ring proposed for accelerations of muons over the momentum range 10-20 GeV/c.  
 
THPLT009 Comparative Transverse Distribution Measurements between the New SPS Rest Gas Ionisation Monitor and the Wire Scanner Monitors. emittance, proton, target, injection 2478
 
  • C. Fischer, B. Dehning, J. Koopman, D. Kramer, F. Roncarolo
    CERN, Geneva
  During the past two years, a new Ionization Profile Monitor was installed and tested in the CERN SPS. In parallel modifications were made on various wire scanner monitors. The aim is to develop instruments performing reliable measurements of transverse beam distributions in the SPS and in the LHC, in order to control the stringent emittance preservation requirements. Measurements made with the two types of monitors were performed under various conditions of LHC type beams, ranging from a pilot bunch up to beams having in the SPS nominal distributions in bunch number, intensity and energy for injection into the LHC. The data provided by the two types of instruments are compared. In the case of discrepancies, an analysis of the possible reasons is made. The cures implemented and the improvements foreseen are discussed.  
 
THPLT015 Accuracy of Profile Monitors and LHC Emittance Measurements emittance, booster, injection, proton 2496
 
  • F. Roncarolo, G. Arduini, B. Dehning, G. Ferioli, J. Koopman, D. Kramer
    CERN, Geneva
  The monitoring and controlling of the beam transverse emittance is essential to allow high luminosity performances in a collider operation. The profile monitors in the LHC injection chain are exploited to determine their precision. A fit strategy was developed to reduce the fitting procedure error and make it negligible compared to instrumentation errors. The method proved to be robust against non-Gaussian tails and can estimate the fraction of non-Gaussian distributed beam intensity. The procedure was applied to the 2003 SPS Wire Scanner measurements with different kind of LHC type beams. The reproducibility of the six available monitors was determined by choosing one as a reference and making synchronized measurements. Several instrumental errors were discovered and corrected to the one per cent level. The demanding small LHC transverse emittances were determined under different beam conditions in terms of intensity, bunch spacing and length in the PS Booster, PS and SPS.  
 
THPLT029 Parallel Particle in Cell Computations with GdfidL electromagnetic-fields, simulation, vacuum, plasma 2538
 
  • W. Bruns
    WBFB, Berlin
  The electromagnetic field solver GdfidL has been extended to compute with free moving charges. For computing in parallel, GdfidL partitions the computational volume in many small subvolumes. Each processor computes the electromagnetic field in its part of the whole volume. In addition to the normal field update equations, the movement of the particles must be computed from the Lorentz-force, and the convection current due to the moving charges must be computed and be used to change the electric field near the particle. For each particle, these computations are performed by the processor which is responsible for the volume where the particle is in. Details of the parallel implementation of the used algorithm, Particle in Cell, are given.  
 
THPLT048 Progress in 3D Space-charge Calculations in the GPT Code space-charge, brightness, electron, emittance 2592
 
  • G. Pöplau, U. Van Rienen
    Rostock University, Faculty of Engineering, Rostock
  • M.J. de Loos
    PP, Soest
  • S.B. van der Geer
    TUE, Eindhoven
  The mesh-based 3D space-charge routine in the GPT (General Particle Tracer, Pulsar Physics) code scales linearly with the number of particles in terms of CPU time and allows a million particles to be tracked on a normal PC. The crucial ingredient of the routine is a non-equidistant multi-grid Poisson solver to calculate the electrostatic potential in the rest frame of the bunch. The solver has been optimized for very high and very low aspect ratio bunches present in state-of-the-art high-brightness electron accelerators. In this paper, we explore the efficiency and accuracy of the calculations as function of meshing strategy and boundary conditions.  
 
THPLT066 Commissioning of 150MeV FFAG Synchronisation injection, septum, extraction, kicker 2643
 
  • Y. Yonemura, M. Matoba
    Kyushu University, Fukuoka
  • M. Aiba, M. Sugaya
    University of Tokyo, Tokyo
  • S. Machida, Y. Mori, A. Muto, J. Nakano, C. Ohmori, I. Sakai, Y. Sato, A. Takagi, T. Yokoi, M. Yoshii, M. Yoshimoto, Y. Yuasa
    KEK, Ibaraki
  • T. Uesugi
    NIRS, Chiba-shi
  • A. Yamazaki
    LNS, Sendai
  A 150MeV proton FFAG (Fixed Field Alternating Gradient) synchrotron has been constructed to be a prototype for various applications such as proton beam therapy. At the moment, all the components are assembled, and multi-turn injection and beam storage were successfully performed. We are in the phase of beam acceleration up to final energy and expect the beam extraction in a few months. In this paper, beam commissioning results such as multi-turn injection, orbit correction, tune survey and optimization of RF gymnastics will be presented.  
 
THPLT078 Construction of FFAG Accelerators in KURRI for ADS Study proton, booster, ion, ion-source 2676
 
  • M. Tanigaki, K. Mishima, S. Shiroya
    KURRI, Osaka
  • S. Fukumoto, Y. Ishi
    Mitsubishi Electric Corp, Energy & Public Infrastructure Systems Center, Kobe
  • M. Inoue
    SLLS, Shiga
  • S. Machida, Y. Mori
    KEK, Ibaraki
  KART (Kumatori Accelerator driven Reactor Test) project has started at Kyoto University Research Reactor Institute (KURRI) from the fiscal year of 2002. The purpose of this project is to demonstrate the basic feasibility of ADS, studying the effect of incident neutron energy on the effective multiplication factor of the subcritical nuclear fuel system. We are now constructing a proton FFAG accelerator complex as a neutron production driver for this project. Our accelerator complex consists of a 2.5 MeV FFAG betatron as an injector and 20 MeV and 150 MeV FFAG synchrotrons as a booster and a main ring, respectively. Our FFAG betatron is a spiral sector type. Both booster and main rings are radial sector type FFAG synchrotrons, but different in the production of required magnetic field with a certain magnetic field index. The distribution of magnetic field is determined by the shaped pole-face in the main ring while the magnetic field is realized by use of trim coils in the booster ring. This FFAG complex will be combined with our Kyoto University Critical Assembly (KUCA) in KURRI by the end of March 2006 and the experiments will begin as soon as the whole system is ready.  
 
THPLT079 The Study of APF-IH Linac linac, ion, focusing, proton 2679
 
  • K. Yamamoto, T. Hattori, K. Yamamoto
    RLNR, Tokyo
  • M. Okamura
    RIKEN, Saitama
  • S. Yamada
    NIRS, Chiba-shi
  We have manufactured the IH linac with Alternating Phase Focus as the test machine of medical accelerator injection. It will accelerate C4+ ion up to 2MeV/u from 40 keV/u, the tank length is around 1.5m, operation frequency is 100MHz. Furthermore, We have succeeded the acceleration test using proton with simple acceleration system consist of P.I.G. ion source, bending magnets and focus lenses, less than 5m long. Otherwise, We have been making the program of beam dynamics with the results of the electro-magnetic simulation soft (Micro-Wave-Studio,OPERA-3D), it has the merit of easily to calculate the 3D- beam dynamics in the tank. We will report the some results of the test and the beam simulation and the comparisons.  
 
THPLT110 Modelling of Accelerating Structures with Finite-difference Time-domain Method simulation, focusing, electromagnetic-fields 2742
 
  • E.V. Pickulin, V.N. Malyshev
    LETI, Saint-Petersburg
  • S.A. Silaev, Y.A. Svistunov
    NIIEFA, St. Petersburg
  A finite-difference time-domain (FDTD) method is very popular for electromagnetic field modeling. The practical interest in the method is the ability to calculate fields in time domain at any time point in the accelerating structure. That is to say the FDTD method is able to model transient process taking into account the peculiarity of RF power input device. A FDTD approach for modeling of alternate phase focusing structure is presented in this paper. The modeling of lossy metals is a problem in classical formulation of FDTD method. This matter is investigated and one of the solutions is presented in this paper. There are some problems of signal processing when using time-domain method for resonant structure modeling. The matters of mode determination are also investigated and presented in this paper. The simulation results are compared with experimental data.  
 
THPLT123 Coupling Coefficients in the Inhomogeneous Cavity Chain coupling, electromagnetic-fields, damping 2759
 
  • K. Kramarenko, M.I. Ayzatskiy
    NSC/KIPT, Kharkov
  In this paper a mathematical method on the base of a rigorous electrodynamic approach for description of inhomogeneous chain of cylindrical cavities is presented. The form of the obtained for chosen amplitudes set of equations is similar to the set of equations that describe the simple coupled circuit chain. As the cavity have the infinite number of resonant frequencies, to obtain the coupling coefficients one have to solve additional infinite set of linear equations with coefficients that depend on the frequency. Using the developed method in the case of inhomogeneous cavity chain we calculated the dependence of the coupling coefficients on frequency and geometrical sizes with taking into account the 'long-range' coupling.  
 
THPLT124 Simulation Technique for Study of Transient Self-consistent Beam Dynamics in RF Linacs simulation, linac, beam-loading, impedance 2762
 
  • V.V. Mytrochenko, A. Opanasenko
    NSC/KIPT, Kharkov
  The report describes a simulation technique for study of unsteady self-consistent dynamics of charged particles in resonant linacs. The technique allows simulating the linacs that consist of resonant cavities and traveling wave sections. The proposed approach is based on unsteady theories of excitation of resonant cavities and waveguides by a beam of charged particles and RF feeders. The theory of waveguide excitation is generalized to the case of spatially inhomogeneous traveling wave structures. The system of self-consistent differential equations for fields and motion of particles is integrated over time and space. The SUPERFISH code is used to evaluate characteristics of the axially symmetrical cavities and traveling wave sections. The PARMELA code is applied to simulate motion of the particles at each time step of the integration. In such a way the fields and beam characteristics in the axially symmetrical accelerating structures can be obtained for transient and steady state operation. Description of the algorithm and results of its validation are presented.  
 
THPLT137 Commissioning of the Head-tail Monitoring Application for the Tevatron synchrotron, kicker, proton, monitoring 2780
 
  • V.H. Ranjbar, V. Lebedev, E. Lorman, A. Xiao
    Fermilab, Batavia, Illinois
  A head-tail beam monitoring application has recently been developed for use in the Tevatron. With this application beam dynamics problems including head-tail instabilities can be monitored. In addition it can be use to perform chromaticity measurements using the head-tail technique developed at CERN. This application speeds up chromaticity measurements in the Tevatron especially during the acceleration ramp and low beta squeeze, which previously required three separate ramps using uncoalesced protons