| Paper | Title | Other Keywords | Page | ||
|---|---|---|---|---|---|
| MPPT002 | Design and Experiment of the BEPCII IR Conventional Dual Aperture Quadrupole | quadrupole, multipole, septum, interaction-region | |||
|
The quadrupole magnet Q1a is one of the final horizontal focus quadrupoles for the Beijing Electron-Positron Collider Interaction Region (BEPCII IR). The BEPCII IR lattice design specification calls for a very high field quality for the quadrupole magnet. The Q1a is a conventional dual apertures quadrupole magnet. The required integral quadrupole strengths in two apertures are the same. This magnet is a septum quadrupole with high current density and solid core. 2D pole contour optimization and pole end chamfers are used to minimize harmonic error. The design methods, experiment results and magnet performances are described in this paper.
|
|
|
||
| MPPT003 | RESOLUTIONS OF PROBLEMS THAT OCCURRED IN SPEAR3 MAGNET | dipole, injection | 838 | ||
|
Funding: DOE National Institutes of Health. |
Few problems occurred during the SPEAR3 magnets production at IHEP, China. It was very hard to find resolution from existing knowledge of those problems. It was possible that similar problems might happen in building accelerator magnet in other institutes before, but they were not addressed in public papers. Those problems were discussed and solved by engineers from both SSRL and IHEP after conducting certain experiments. Traditionally, the magnet design and measurement data have been always well documented and addressed in the papers, but the production experiences have not been recorded adequately. It is the goal of this paper to record the problems and their resolutions during SPEAR3 magnet production, which will certainly benefit future magnet projects. |
|
||
| MPPT009 | HTS Power Leads for the BTeV Interaction Region | quadrupole, interaction-region, power-supply, accumulation | 1147 | ||
|
Funding: DOE |
A new Interaction Region for the BTEV experiment is planned to be built soon at Fermilab. This IR will require new superconducting quadrupole magnets and many additional power circuits for their operation. The new "low beta" quadupole magnet design is based upon the Fermilab LHC quadrupole design, and will operate at 9.56 kA in 4.5 K liquid helium. The use of conventional power leads for these circuits would require substantially more helium for cooling than is available from the cryogenic plant, which is already operating close to its limit. To decrease the heat load and helium cooling demands, the use of HTS power leads is necessary. Fermilab is in the process of procuring HTS leads for this new interaction region. Several 6 kA HTS leads produced by American Superconductor Corporation have been tested at over-current conditions. Based on the test results, design requirements are being developed for procuring the HTS current leads. This paper summarizes the test results and describes the design requirements for the 9.65 kA HTS power leads. |
|
||
| MPPT046 | Superconducting Helical Snake Magnet for the AGS | dipole, resonance, proton, acceleration | 2935 | ||
|
Funding: DOE |
A superconducting helical magnet has been built for polarized proton acceleration in the Brookhaven AGS. This "partial Snake" magnet will help to reduce the loss of polarization of the beam due to machine resonances. It is a 3 T magnet some 1940 mm in magnetic length in which the dipole field rotates with a pitch of 0.2053 degrees/mm for 1154 mm in the center and a pitch of 0.3920 degrees/mm for 393 mm in each end. The coil cross-section is made of two slotted cylinders containing superconductor. In order to minimize residual offsets and deflections of the beam on its orbit through the Snake, a careful balancing of the coil parameters was necessary. In addition to the main helical coils, a solenoid winding was built on the cold bore tube inside the main coils to compensate for the axial component of the field that is experienced by the beam when it is off-axis in this helical magnet. Also, two dipole corrector magnets were placed on the same tube with the solenoid. A low heat leak cryostat was built so that the magnet can operate in the AGS cooled by several cryocoolers. The design, construction and performance of this unique magnet will be summarized. |
|
||
| MPPT056 | First Ideas Towards the Super-Conducting Magnet Design for the HESR at FAIR | dipole, quadrupole, sextupole, antiproton | 3354 | ||
|
The Forschungszentrum Juelich has taken the leadership of a consortium being responsible for the design of the HESR going to be part of the FAIR project at GSI. The HESR is a 50 Tm storage ring for antiprotons, based on a super-conducting magnet technology. On basis of the RHIC Dipole D0 (3.6 T), the magnet design for the HESR has started recently. One key issue will be a very compact layout because of the rather short magnets (been 1.82 m for the dipoles and 0.5 m for the other magnets). This paper will present first ideas of the magnetic and cryogenic layout, give a status report on the achievements so far and discuss the need and possible solutions for a bent magnet with a radius of curvature of 13.2 m.
|
|
|
||
| MPPT081 | Undulator for the LCLS Project - Changes in the Magnet Structure Design | undulator, permanent-magnet, site | 4075 | ||
|
The design modifications of a new hybrid-type undulator with a fixed gap of 6.4 mm, a period of 30 mm and a length of 3.4 m are presented. The prior pole design included side "wings" which were used for precise positioning, and clamps to fasten poles to the magnet base. This design has been replaced by a more straightforward assembly, where the pole is attached to the magnet structure base using only two screws. Tests were performed on the vanadium permendure pole material to prove that the threaded holes are easy to fabricate and are able to successfully withstand the torque required to hold the pole in place. A fixture was also developed to ensure the precise location of the poles on the base during assembly. In addition to the pole modifications, the magnet structure base is now manufactured as one piece as opposed to three, which greatly eases assembly. Finally, a small section of the original prototype had these changes successfully implemented, and the test results are presented.
|
|
|
||
| ROAB009 | NuMI Proton Kicker Extraction System | kicker, coupling, extraction, injection | 692 | ||
|
Funding: Fermilab is operated by Universities Research Association Inc. under Contract No. DE-AC02-76CH03000 with the U.S. Department of Energy. |
This system extracts up to 9.6 us of 120 GeV beam every 1.87 seconds for the NuMI beamline neutrino experiments. A pulse forming network consisting of two continuous wound coils and 68 capacitors was designed and built to drive three kicker magnets. The field stability requirement is better than ± 1% with a field rise time of 1.6 us. New kicker magnets were built based on the successful traveling wave magnets built for the Main Injector. Two of these magnets, which have a propagation time of 550 ns, are in series making the risetime of the pulser a serious constraint. A forced cooling system using FluorinertŪ was designed for the magnet termination resistors to maintain the field flatness and amplitude stability. The system has been commissioned and early results will be presented. |
|