A   B   C   D   E   F   G   H   I   K   L   M   N   O   P   Q   R   S   T   U   V   W    

single-bunch

    
Paper Title Other Keywords Page
MOPKF082 A Multi-bunch, Three-dimensional, Strong-strong Beam-beam Simulation Code for Parallel Computers luminosity, simulation, beam-beam-effects, target 509
 
  • A.C. Kabel, Y. Cai
    SLAC, Menlo Park, California
  We have developed a parallel simulation code allowing the self-consistent, three-dimensional simulation of the strong-strong beam-beam effect, using a particle-on-mesh technique and fast elliptic solvers. It is able to operate with sufficiently high logitudinal resolution to treat phase-averaging and hourglass effects in the interaction point (IP) correctly. This code has been generalized to handle the collisions of an arbitrary set of bunches at arbitrary positions in the ring (parasitic crossings), using appropriately reduced longitudinal resolution of collisions not in the design IP. We provide benchmarking results and parameter studies based on PEP-II.  
 
TUPLT074 Dark Current Reduction System for SPring-8 Linac linac, storage-ring, gun, synchrotron 1324
 
  • T. Kobayashi, T. Asaka, H. Hanaki, M. Shoji, S. Suzuki, K. Tamura
    JASRI/SPring-8, Hyogo
  The SPring-8 linac accelerates dark currents generated by its injector part up to 1 GeV. These dark currents are injected with main beam into the SPring-8 storage ring and then spoil the purity of the stored beam. The dark currents are mainly composed of a grid emission current from a thermionic gun and field emission currents from rf accelerating structures. A beam deflector for kicking only the grid emission by a pulsed electric field was developed and installed in the SPring-8 linac. We observed that the beam deflector greatly reduced the grid emission current accelerated up to 1 GeV. The measured purity of the stored single-bunched beam was about 5x10-6 when the deflector operated, which was almost 1/100 of the purity without filtering by the deflector. However, the deflector, which is installed before the prebucher, cannot reduced the field emission currents from the buncher cavities and the first acccelerating structure. These dark currents take considerable proportion of the total dark currents observed at the end of the linac. We are trying to spin off the field emission currents by weak magnetic fields across the accelerating structure generated by several coils.  
 
WEPKF043 Measurement of the Vertical Quadrupolar Tune Shift in the Photon Factory Storage Ring storage-ring, betatron, factory, photon 1702
 
  • S. Sakanaka, T. Mitsuhashi, T. Obina
    KEK, Ibaraki
  We measured the frequencies of vertical quadrupole oscillations in the 2.5-GeV Photon Factory storage ring at KEK. The measured vertical quadrupole tunes showed remarkable dependence of about -7.5E-5/mA on the bunch current. This contrasts with our previous result of about +4.8E-5/mA (presented in PAC2003) for the horizontal quadrupole tune shift. These results will suggest that the transverse wake forces in a quadrupolar mode contribute significantly to the transverse motions of particles in the Photon Factory storage ring.  
 
WEPLT036 Energy Loss of a Single Bunch in the CERN SPS impedance, kicker, beam-loading, pick-up 1909
 
  • E.N. Shaposhnikova, T. Bohl, T.P.R. Linnecar, J. Tuckmantel
    CERN, Geneva
  • A. Hofmann
    Honorary CERN Staff Member, Grand-Saconnex
  The dependence of energy loss on bunch length was determined experimentally for a single proton bunch in the SPS at 26 GeV/c. This was done from measurements of the synchronous phase as a function of intensity for different capture voltages. The results are compared with the expected dependence calculated from the resistive part of the SPS impedance below 1 GHz. Two impedance sources, the cavities of the 200 MHz RF system and the extraction kickers, give the main contributions to particle energy loss in very good agreement with experiment. The results obtained allow a better understanding of some mechanisms leading to capture loss of the high intensity LHC beam in the SPS.  
 
WEPLT069 Investigation of Scraper Induced Wake Fields at ANKA impedance, closed-orbit, synchrotron, storage-ring 2008
 
  • A.-S. Müller, I. Birkel, E. Huttel, M. Pont, F. Pérez
    FZK-ISS-ANKA, Karlsruhe
  • F. Zimmermann
    CERN, Geneva
  The ANKA synchrotron light source operates in the energy range from 0.5 to 2.5 GeV. Typical requirements for light sources include small beam sizes, large lifetimes and high currents to provide the highest possible photon flux. The understanding of impedance and instability related issues is very important in order to improve the machine performance, in particular when small aperture insertion devices are installed that require protection by a scraper. In the framework of an impedance survey the transverse and longitudinal wake fields induced by a vertical scraper have been measured and analysed. This paper reports the beam observations and compares them with the expectation.  
 
WEPLT073 VDHL Design and Simulation of a Fast Beam Loss Interlock for TTF2 beam-losses, linac, simulation, electron 2020
 
  • A. Hamdi
    CEA/Saclay, Gif-sur-Yvette
  • M. Luong
    CEA/DSM/DAPNIA, Gif-sur-Yvette
  • M. Werner
    DESY, Hamburg
  The TTF2 fast beam loss interlock provides different modes of protection. Based on the differential beam charge monitoring over a macropulse, a pulse slice or bunch-by-bunch, the signal processing time should be as short as the bunch repetition period (110 ns). The signal delivered by the toroid-like inductive current transformer always shows an envelope droop due to its self-inductance to resistance ratio. When the macropulse length is comparable to this ratio, the charge of each bunch must be derived from the difference of the top to the bottom level on the signal. This necessity combined to the various protection modes leads to a digital implementation. All the processing functionalities are designed with VHDL for a Xilinx FPGA. Because the interlock involves other control signals in addition to the toroid signal with specific shapes, which cannot be easily reproduced for the design validation before the TTF2 completion, VHDL provides meanwhile the possibility for an exhaustive validation of the system with a software test bench including all timing information.  
 
WEPLT080 Study of Resistive-wall Effects on SOLEIL impedance, vacuum, focusing, synchrotron 2038
 
  • R. Nagaoka
    SOLEIL, Gif-sur-Yvette
  The presence of low-gap chambers for insertion devices, along with a relatively small vertical gap of 25 mm chosen for the standard vacuum chambers, implies a significant influence of the resistive-wall on the beam in the future SOLEIL storage ring. A systematic approach was taken to quantify the net contribution by taking into account all local variations of the non-circular chamber cross-sections as well as beta functions. Low multibunch instability thresholds were found in both transverse planes, indicating the necessity of cures, by means of transverse feedback and/or chromaticity shifts. An effort was made to evaluate the effect of metallic coating, particularly that of NEG, which was adopted in all straight sections. The dependence on both resistivity and thickness of NEG was followed. It is found that, the NEG coating nearly doubles the reactive part of the impedance in the frequency range seen by the beam. Implication on the reduction of the transverse mode-coupling instability threshold is discussed. Incoherent tune shifts arising from the non-circular chamber cross-section were also evaluated, including a non-negligible NEG contribution in the short-range wakes.  
 
WEPLT083 Coherent and Incoherent Tune Shifts Deduced from Impedance Modelling in the ESRF-Ring impedance, vacuum, storage-ring, coupling 2047
 
  • T.F. Günzel
    ESRF, Grenoble
  In single bunch the detuning of the transverse modes m=0,1 and -1 are calculated on the base of an impedance model contructed from element-wise wakefield calculation and the resistive wall impedance of the ESRF-ring. As the vacuum chambers of the ESRF storage ring have notably flat cross sections incoherent wake fields have an impact on the tune shifts as well as coherent wake fields. Compared to tune shift measurements in single bunch the calculated transverse mode detuning can explain half of the tune shift in the vertical plane and almost completely the tune shift in horizontal plane.  
 
WEPLT093 Electromagnetic Fields of an Off-axis Bunch in a Circular Pipe with Finite Conductivity and Thickness - I multipole, vacuum, injection, electromagnetic-fields 2068
 
  • S. Petracca, L. Cappetta, T. Demma
    U. Sannio, Benevento
  The electromagnetic field produced by a bunched beam in a circular pipe is usually computed under the assumption that the field penetration(skin depth) is far less than the wall thickness. Chao [*] gave a formula which exploits the wall thickness, but his result is restricted to the monopole term. Piwinski [**] treated the case of a metal coated ceramic wall, when the coating thickness is much smaller than the skin-depth, but his analysis is also limited to the monopole term.In this paper we solve the problem in full generality, by providing an exact (Green's functions) solution for the field of an off-axis point particle running at constant velocity in a circular pipe with finite wall conductivity and thickness.

* A.W. Chao, Phys. of Collective Beam Instab. in High En. Accel., Wiley,1993** S. Piwinski, DESY 1972/72

 
 
WEPLT122 Investigation of Microwave Instability on Electron Storage Ring TLS impedance, simulation, damping, storage-ring 2140
 
  • M.-H. Wang
    NSRRC, Hsinchu
  • A. Chao
    SLAC, Menlo Park, California
  With the planned installation of a superconducting rf system, the new operation mode of TLS, the electron storage ring at NSRRC, is expected to double the beam intensity. Several accelerator physics topics need to be examined. One of these topics concerns the beam instability of single-bunch longitudinal microwave instability. We consider different approaches to measure the effective broad band impedance. We compare these measurement results with each other and to the old data [*]. The new measurements of effective broad band impedance are higher than the old measurement since between these two sets of measurements several narrow gap insertion devices were installed into the storage ring. We calculate the threshold current of microwave instability with a mode-mixing analysis code written by Dr. K. Oide of KEK [**]. We also develop a multi-particle tracking code to simulate the instability. The results of simulation and measurement are compared and discussed. We conclude that the doubling of beam current will not onset the microwave instability even without a Landau cavity to lengthen the bunch.

* M.H. Wang, et al.,"Longitudinal Beam Instability Observation with streak Camera at SRRC", proceeding of 1996 European Particle Accelerator Conference, pp. 1120** K. Oide, "Longitudinal Single-Bunch Instability in Electron Storage Rings", KEK Preprint 90-10

 
 
WEPLT144 New Characteristics of a Single-bunch Instability Observed in the APS Storage Ring betatron, synchrotron, storage-ring, lattice 2173
 
  • C.-X. Wang
    ANL, Argonne, Illinois
  • K. Harkay
    ANL/APS, Argonne, Illinois
  In the Advanced Photon Source storage ring, a transverse single-bunch instability has long been observed that appears unique to this ring. Many of its features have been previously reported. New results have recently been obtained using beam centroid history measurements and analysis. These preliminary results provide more detailed information regarding the characteristics of this instability and could provide insight into the physics mechanism.  
 
THOACH03 Top-up Operation at SPring-8 - Towards Maximizing the Potential of a 3rd Generation Light Source injection, storage-ring, target, beam-losses 222
 
  • H. Tanaka, T. Aoki, T. Asaka, S. Daté, K. Fukami, Y. Furukawa, H. Hanaki, N. Hosoda, T. Kobayashi, N. Kumagai, M. Masaki, T. Masuda, S. Matsui, A. Mizuno, T. Nakamura, T. Nakatani, T. Noda, T. Ohata, H. Ohkuma, T. Ohshima, M. Oishi, S. Sasaki, J. Schimizu, M. Shoji, K. Soutome, M. Suzuki, S. Suzuki, S. Takano, M. Takao, T. Takashima, H. Takebe, K. Tamura, R. Tanaka, T. Taniuchi, Y. Taniuchi, K. Tsumaki, A. Yamashita, K. Yanagida, H. Yonehara, T. Yorita
    JASRI/SPring-8, Hyogo
  • M. Adachi, K. Kobayashi, M. Yoshioka
    SES, Hyogo-pref.
  Top-up operation maximizes research activities in a light source facility by an infinite beam lifetime and photon beam stability. We have been improving the SPring-8 accelerators to achieve the ideal top-up operation. For the perturbation-free injection, we adjusted the magnetic field shape of four bump magnets to close the bump orbit, and introduced a scheme to suppress the stored beam oscillation induced by the nonlinearlity of sextupole magnets. These reduced the horizontal oscillation down to a third of the stored beam size. For the loss-free injection, beam collimators were installed upstream of the injection line. This realized the injection efficiency of ~100% under the restricted gap condition of in-vacuum insertion devices (ID). Since autumn 2003, we have been injecting the beams keeping the photon beam shutters opened and ID gaps closed. We developed a bunch-by-bunch feedback system to reduce the beam loss further with all the ID gaps fully closed by lowering the operating chromaticity. The operation with constant stored current is scheduled in June 2004. We present the overview and progress of the SPring-8 top-up operation focusing on our developments and results.  
Video of talk
Transparencies
 
THOALH03 The Measurements of the Longitudinal Beam Profile on the Preinjector VEPP-5 electron, radiation, space-charge, linac 259
 
  • S. Gurov, P.A. Bak, P.V. Logatchev, V. Pavlov, E. Pyata
    BINP SB RAS, Novosibirsk
  • D. Chernousov
    ICKC, Novosibirsk
  For effective work of preinjector VEPP-5 it is necessary 3 ns bunch with charge 1* 1010 electrons from termogun compress to bunch with 40 ps duration on the positron target. A new streak-camera with RF cavity on the main linac frequency is used. Streak-camera with circle scanning allows see 350 ps single light signal with sub-ps resolution. An additional slow scanning can obtain the trochoidal scanning. Thus one can see with picosecond resolution and with less then 1 psec synchronization the train of ten bunches which are spacing by 350psec. The results of worked streak-camera with RF-cavity for circle scanning are presented.  
Video of talk
Transparencies
 
THPKF006 Lifetime Studies in the LNLS Electron Storage Ring storage-ring, scattering, synchrotron, coupling 2266
 
  • N.P. Abreu, P.F. Tavares
    LNLS, Campinas
  In this paper we present a set of measurements performed at the 1.37 GeV electron storage ring of the Brazilian Synchrotron Light Source. We measured the beam lifetime as a function of: current per bunch, gap voltage and position of horizontal and vertical scrapers. Those measurements helped us to determine the contribution of various particle loss mechanisms (Touschek, elastic and inelastic scattering and quantum fluctuations) to the lifetime of the beam. Comparison with theory is also presented as well as an interpretation of each effect.  
 
THPKF015 Compressed Electron Bunches for THz-Generation - Operating BESSY II in a Dedicated Low Alpha Mode optics, radiation, electron, sextupole 2290
 
  • G. Wustefeld, J. Feikes, K. Holldack, P. Kuske
    BESSY GmbH, Berlin
  For the first time an electron storage ring was operated during regular user shifts in a dedicated 'low alpha' mode, where electron bunches are compressed to 5 times shorter length for THz [*] and short X-ray pulses experiments. The 1 mm rms-long bunches emit powerfull, coherent THz waves, up to 107 times stronger than incoherent radiation. We report on machine set up and operating experience.

* M. Abo-Bakr et al., Phys. Rev. Lett. 88, 254801 (2002)

 
 
THPLT005 Ultra-high Frequency Scanning Cavities for Non-relativistic Electron Beam electron, polarization, target, impedance 2466
 
  • G.G. Oksuzyan, E.D. Gazazyan, A.T. Margaryan, A.D. Ter-Poghosyan
    YerPhI, Yerevan
  • M. Ivanyan
    CANDLE, Yerevan
  The different scanning schemes based on the RF cavities for non-relativistic electron beam are examined. Optimization criteria for various types of cavities were developed. A complete picture of the beamscanning at a given point of interest is obtained.  
 
THPLT017 Review and Comparison of Simulation Codes Modeling Electron-Cloud Build Up and Instabilities electron, simulation, emittance, proton 2502
 
  • F. Zimmermann, E. Benedetto, F. Ruggiero, D. Schulte
    CERN, Geneva
  • G. Bellodi
    CCLRC/RAL/ASTeC, Chilton, Didcot, Oxon
  • M. Blaskiewicz, L. Wang
    BNL, Upton, Long Island, New York
  • Y. Cai, M.T.F. Pivi
    SLAC, Menlo Park, California
  • V.K. Decyk, W. Mori
    UCLA, Los Angeles, California
  • M.A. Furman
    LBNL/AFR, Berkeley, California
  • A.F. Ghalam, T. Katsouleas
    USC, Los Angeles, California
  • K. Ohmi, S.S. Win
    KEK, Ibaraki
  • G. Rumolo
    GSI, Darmstadt
  Several computer codes written at various laboratories are employed for modelling the generation and the consequences of an electron cloud. We review the most popular of these programs, which simulate either the build of an electron cloud or the instabilities it produces, and we compare simulation results for identical, or similar, input parameters obtained from the various codes.  
 
THPLT159 Instability Thresholds and Generation of the Electron-cloud in the GLC/NLC and Tesla Damping Rings electron, damping, simulation, synchrotron 2831
 
  • M.T.F. Pivi, T.O. Raubenheimer
    SLAC/NLC, Menlo Park, California
  In the beam pipe of the Damping Ring (DR) of a linear collider, an electron cloud may be produced by ionization of residual gas and secondary emission. This electron cloud can reach equilibrium after the passage of only a few bunches. We present recent computer simulation results for the main features of the electron cloud generation in the GLC/NLC main DR and for the TESLA DR. Single and multi-bunch instability thresholds are also calculated for the NLC main DR. The results are obtained by the computer simulation codes HEAD-TAIL and POSINST, which were developed to study the electron cloud effect in particle accelerators.