• J. Peters
  DESY, Hamburg

The HERA RF-Volume Source is the only source that delivers routinely a H – current of 40 mA without Cs. It has been running for years without interruption for maintenance. The production mechanism for H – ions in this type of source is still under discussion. Laser photodetachment measurements have been done at DESY in order to measure the H – distribution in the source. The measurements were done also under extraction conditions at high voltage. The dependency of the quality of the Hminus beam on the frequency was investigated. A frequency range of 1.65 – 9 Mhz was scanned and the emittance was measured for several Hminus currents up to 40 mA. The results of our investigations make further source improvements possible. Recently currents of 60 mA were reached.

• M. Cavenago
  INFN/LNL, Legnaro, Padova
• V. Antoni, F. Sattin
  CNR/RFX, Padova
• A. Tanga
  MPI/IPP, Garching

Effects of plasma meniscus on the emittance in negative ion source proposed for spallation sources or neutral beam injectors (NBI) for tokamaks are particularly interesting to study with fluid models because: 1) at least three different charged fluid can be recognised: the thermalized and fully magnetized electrons; the slightly magnetized and roughly thermalized positive ions; the negative ions, typically formed within few cm from meniscus; 2) different implementation of the magnetic filter system need to be compared; 3) optimization of electron dump and outlet electrode strongly depends on plasma meniscus contact point. With reasonable assumption on system geometry, 2D and 3D charged fluid quation for the selfconsistent electrostatic field can be written and effect of grid aperture is investigated. Moreover, these equations are easily implemented into a multiphysics general purpose program. Preliminary results are described, and compared to existing codes.

• M. Re, F. Chines, G. Cuttone, M. Menna, E. Messina
  INFN/LNS, Catania
• J.-C. Bilheux, D.W. Stracener
  ORNL, Oak Ridge, Tennessee

• I.-S. Hong, Y.-S. Cho, S.-H. Han
  KAERI, Daejon

Duoplasmatron type ion source with 50keV proton beam has been constructed and stably operated as the injector for Proton Engineering Frontier Project(PEFP). In DC operation, the beam current of 50mA with 50kV extraction voltage is routinely obtained. However, the pulsed operation mode of the ion source also has been considered to reduce beam induced damage at the entrance of RFQ. A high voltage pulse switch is connected between accelerating electrode and ground electrode for this purpose. The detailed scheme on the focusing of the pulsed proton beam with space charge compensation is in progress. Beam profile and current in front of RFQ will be measured by DCCT and optical measuring tools.

• R.C. Pardo, S.I. Baker, A.A.H. Hecht, E.F. Moore, G. Savard
  ANL, Argonne, Illinois

An upgrade to the radioactive beam capability of the ATLAS facility has been proposed using 252Cf fission fragments thermalized and collected into a low-energy particle beam using a helium gas catcher. In order to reaccelerate these beams an existing ATLAS ECR ion source will be reconfigured as a charge breeder source. A 1Ci 252Cf source is expected to provide sufficient yield to deliver beams of up to ~106 far from stability ions per second on target. A facility description, the expected performance and the expected performance will be presented in this paper. This work is supported by the U.S. Department of Energy, Office of Nuclear Physics, under contract W-31-109-ENG-38.

• D. Raparia, Y.Y. Lee, J. Wei
  BNL, Upton, Long Island, New York

• J. Qiang, D. Leitner, D.S. Todd
  LBNL, Berkeley, California

The driver linac of the proposed Rare Isotope Accelerator (RIA) requires a great variety of high intensity, high charge state ion beams. In order to design and optimize the low energy beam line optics of the RIA front end, we have developed a new parallel three-dimensional model to simulate the low energy, multi-species beam transport from the ECR ion source extraction region to the focal plane of the analyzing magnet. A multi-section overlapped computational domain has been used to break the original transport system into a number of independent subsystems. Within each subsystem, macro-particle tracking is used to obtain the charge density distribution in this subdomain. The three-dimensional Poisson equation is solved within the subdomain and particle tracking is repeated until the solution converges. Two new Poisson solvers based on a combination of the spectral method and the multigrid method have been developed to solve the Poisson equation in cylindrical coordinates for the beam extraction region and in the Frenet-Serret coordinates for the bending magnet region. Some test examples and initial applications will also be presented.

• G.A. Westenskow, D.P. Grote, E. F. Halaxa
  LLNL, Livermore, California
• F.M. Bieniosek, J.W. Kwan
  LBNL, Berkeley, California

To provide compact high-brightness heavy-ion beams for Heavy Ion Fusion (HIF) accelerators, we have been experimenting with merging multi-beamlets in an injector which uses an RF plasma source. In an 80-kV 20-microsecond experiment, the RF plasma source has produced up to 5 mA of Ar+ in a single beamlet. An extraction current density of 100 mA/cm2 was achieved, and the thermal temperature of the ions was below 1 eV. More than 90% of the ions were in the Ar+ state, and the energy spread from charge exchange was found to be small. We have tested at full voltage gradient the first 4 gaps of a 61-beamlet injector design. Einzel lens were used to focus the beamlets while reducing the beamlet to beamlet space charge interaction. We will report on a converging 119 multi-beamlet source. Although the source has the same optics as a full 1.6 MV injector system, the test will be carried out at 400 kV due to the test stand HV limit. We will measure the beam’s emittance after the beamlets are merged and have been transported through an electrostatic quadrupole. Our goal is to confirm the emittance growth and to demonstrate the technical feasibility of building a driver-scale HIF injector.

• E.R. Forringer, H.G. Blosser
  NSCL, East Lansing, Michigan

• Q. Zhao, A.I. Balabin, M. Doleans, F. Marti, J.W. Stetson, X. Wu
  NSCL, East Lansing, Michigan

• Y. Kawai, G. Alton, Y. Liu
  ORNL, Oak Ridge, Tennessee

Radioactive atoms produced by the ISOL technique must diffuse from a target, effusively flow to an ion source, be ionized, be extracted, and be accelerated to research energies in a time commensurate with the lifetime of the species of interest. We have developed a fast valve system (closing time ~100 us) that can be used to accurately measure the effusion times of chemically active or inactive species through arbitrary geometry and size vapor transport systems with and without target material in the reservoir. The effusive flow times are characteristic of the system and thus serve as figures of merit for assessing the quality of a given vapor transport system as well as for assessing the permeability properties of a given target design. This article presents effusive flow data for noble gases flowing through a target reservoir and ion source system routinely used to generate radioactive species at the HRIBF with and without disks of 6 times and 10 times compressed Reticulated Vitreous Carbon Foam (RVCF) with the objective of determining the added delay time associated with each of these target matrices.

• Y. Kawai, G. Alton, J. O. Kiggans, D.W. Stracener
  ORNL, Oak Ridge, Tennessee

A new infiltration paint coating method has been developed for fabricating ISOL targets for radioactive ion beam applications. The technique has been shown to be inexpensive, fast, and almost universal for the uniform deposition of many refractory target materials onto the interior surfaces of complex geometry matrices, such as Reticulated-Vitreous-Carbon-Foam (RVCF). The process yields robust, highly permeable targets with fast diffusion and release properties. We demonstrate the viability of the technique for coating forms of RVCF compressed by factors of 6 and 10 with materials to form targets for use at high energy facilities such as RIA. The use of compressed RVCF, coated with an optimum thickness of target material, reduces target lengths to practical values, while preserving high permeability. We calculate thermal conductivities and diffusion for various targets on 6xRVCF and 10xRVCF.

• Y. Kawai, G. Alton, Y. Liu
  ORNL, Oak Ridge, Tennessee

The multiple discrete frequency technique has been used to improve the performance of conventional B-field configuration ECR ion sources. However, the practical application of this technique is very costly, requiring multiple independent single-frequency rf power supplies and complicated rf injection systems. Broadband sources of rf power offer a low-cost and more effective method for increasing the physical size of the ECR zone within these ion sources. An Additive White Gaussian Noise Generator (AWGNG) system for injecting broadband rf power into these ion sources has been developed in conjunction with a commercial firm. The noise generator, in combination with an external oscillator and a traveling wave tube amplifier, can be used to generate broadband rf power without modifying the injection system. The AWGNG and its use for enhancing the performance of conventional B-field configuration ECR ion sources will be described.

• Y. Liu, H. Z. Bilheux, Y. Kawai
  ORNL, Oak Ridge, Tennessee

Elements with low ionization potentials can be efficiently ionized by positive surface ionization. It has been experimentally observed and theoretically shown that the ionization efficiency in a hot-cavity can be significantly higher than expected for the surface ionization mechanism. This is explained by the existence of a thermal plasma inside the cavity consisting of surface ionized ions and thermionic electrons. We have investigated the suggested ioniation mechanisms in a tubular hot-cavity surface ionization source where the area of the exit aperture is small compared with the tube inner surface. Thermal analyses of the tubular cavity and calculated mean number of wall collisions of a neutral particle in the cavity before escaping through the exit aperture are presented. Measured emittance and ionization efficiencies of various elements as a function of the cavity temperature for different cavity materials are discussed.

• Y. Liu, C. Baktash, J.R. Beene, H. Z. Bilheux, C.C. Havener, H.F. Krause, D.R. Schultz, D.W. Stracener, C.R. Vane
  ORNL, Oak Ridge, Tennessee
• K. Brueck, Ch. Geppert, T. Kessler, K. Wendt
  Johannes Gutenberg University Mainz, Mainz

The isobaric purity of radioactive ion beams (RIBs) is of crucial importance to many experiments. Laser ion sources based on resonant photoionization have already proved to be of great value at existing ISOL RIB facilities. In these ion sources, ions of a selected isotope are produced by laser radiation via stepwise atomic resonant excitations followed by ionization in the last transition. Because each element has its own unique atomic energy levels, the resonant photoionization process can provide elemental selectivity of nearly 100%. We have initiated a research effort to develop a prototype laser ion source with the potential to achieve the high selectivity and high efficiency required for research with ISOL-generated RIBs at the Rare Isotope Accelerator (RIA). A pilot experiment has been conducted to demonstrate resonant photoionization of three atomic species using all-solid-state tunable Ti:Sapphire lasers. Three Ti:Sapphire lasers were provided by the University of Mainz and used in the experiment for three-photon resonant ionization of the elements. Laser generated Sn, Ni, and Ge ions have been successfully obtained in a hot-cavity laser ion source with overall efficiencies of 22%, 2.7%, and 3.3%, respectively.

• D.W. Stracener, G. Alton, J.R. Beene, H. Z. Bilheux, J.-C. Bilheux, J.C. Blackmon, D. Dowling, R.C. Juras, Y. Kawai, Y. Liu, M.J. Meigs, P.E. Mueller, B. A. T. Tatum
  ORNL, Oak Ridge, Tennessee
• H.K. Carter, A. Kronenberg, E.H. Spejewski
  Center of Excellence for RIB Studies for Stewardship Science, Oak Ridge Associated Universities, Oak Ridge, Tennessee

Radioactive beams are produced at the Holifield Radioactive Ion Beam Facility (HRIBF) at Oak Ridge National Laboratory using the Isotope Separator On-Line (ISOL) technique. Radioactive nuclei are produced in a thick target via irradiation with energetic light ions (protons, deuterons, helium isotopes) and then post-accelerated to a few MeV/nucleon for use in nuclear physics experiments. An overview of radioactive beam development at the HRIBF will be presented, including ion source development, improvements in the ISOL production targets, and a description of techniques to improve the quality (intensity and purity) of the beams. Facilities for radioactive ion beam development include two ion source test facilities, a target/ion source preparation and quality assurance facility, and an in-beam test facility where low intensity production beams are used. A new test facility, the High Power Target Laboratory, will be available later this year. At this facility, high intensity production beams will be available to measure the power-handling capabilities of ISOL production targets. This information will be used to optimize target materials and geometries for high power densities.

• Y. Zhang, G. Alton, Y. Kawai
  ORNL, Oak Ridge, Tennessee

Delay times associated with diffusion release from targets and effusive-flow transport of radioactive isotopes to ion sources are principal intensity limiters at ISOL-based radioactive ion beam facilities, and simulation studies with computer models are cost effective methods for designing targets and vapor transport systems with minimum delay times to avoid excessive decay losses of short lived ion species. A finite difference code, Diffuse II, was recently developed at the Oak Ridge National Laboratory to study diffusion-release of short-lived species from three principal target geometries. Simulation results are in close agreement with analytical solutions to Fick’s second equation. Complementary to the development of Diffuse II, the Monte-Carlo code, Effusion, was developed to address issues related to the design of fast vapor transport systems. Results, derived by using Effusion, are also found to closely agree with experimental measurements. In this presentation, the codes will be used in concert to make realistic estimations of intensities of a number of short-lived isotopes that are candidates for use in future nuclear physics and nuclear astrophysics experiments at the HRIBF.

• R. Keller, P.A. Luft, M. T. Monroy, A. Ratti, M.J. Regis, D. L. Syversrud, J.G. Wallig
  LBNL, Berkeley, California
• D.E. Anderson, R.F. Welton
  ORNL, Oak Ridge, Tennessee

A novel concept for creating intense beams of negative hydrogen ion beams is presented. In this approach, an ECR ion source operating at 2.45 GHz frequency is utilized as a primary plasma generator and coupled to an SNS-type multi-cusp H^- ion source. The secondary source is driven by chopped dc power avoiding the use of filaments or of an internal rf antenna. The development of the new ion source is aimed at the future beam-power goal of 3 MW for the Spallation Neutron Source (SNS) that will be pursued after the start of SNS operations, but application to other proton driver accelerators that include an accumulator ring is feasible as well. The first two phases of this development effort have been successfully completed: assembly of a test stand and verification of the performance of an rf-driven SNS ion-source prototype; and extraction of electrons with more than 350 mA current from a 2.45-GHz ECR ion source obtained on loan from Argonne National Laboratory. The next goal is the demonstration of actual H^- ion production by this novel, hybrid ion source. This paper describes the source principle and design in detail and reports on the current status of the development work.

• K. Dunkel, F. Kremer, C. Piel, J. Plitzko
  ACCEL, Bergisch Gladbach

• D.C. Faircloth, R. Sidlow, M. Whitehead, T.W. Wood
  CCLRC/RAL/ISIS, Chilton, Didcot, Oxon

The development of H^- ion sources with performances exceeding those achieved today is a key requirement for the next generation of high power proton accelerators. The Penning surface plasma source development program at ISIS is now well established. To allow different ion source designs to be fully tested, the ability to vary the Penning field is required. Until now the Penning field has been generated by the same magnetic circuit that creates the analyzing field, giving no practical way of altering the Penning field alone. This paper describes the infrastructure changes required to allow the Penning field to be independently varied. The effect the Penning field has on beam current, emittance and discharge stability are discussed.

• K. Sakakibara, T. Hattori, N. Hayashizaki, T. Ito
  RLNR, Tokyo
• H. Kashiwagi
  JAERI/ARTC, Gunma-ken
• M. Okamura
  RIKEN, Saitama

• F.W. Meyer, Y. Liu
  ORNL, Oak Ridge, Tennessee
• H.J. You
  Hanyang University, Seoul

In this paper, real-time, in-situ, plasma potential measurements are reported for an ECR ion source and correlated with extracted beam characteristics. The local real-time plasma potential of the ORNL CAPRICE ECR ion source was measured using an emissive probe, which was inserted perpendicularly from the plasma chamber wall at the mid-plane of the ECR zone between one of the six radial loss cones of the magnetic field structure, where perturbation of the main ECR plasma is expected to be small. Slots machined through the plasma- and puller-electrodes at the plasma chamber wall radius permitted insertion of the probe from the extraction side of the ECR source without perturbation of the coaxial microwave injection. The emissive probe technique permits plasma potential determination independent of plasma conditions and avoids problems related to probe geometry. The probe loop tip was pointed toward the chamber center in a radial plane and was located about 5 mm outside of the ECR zone. Details of the measurements, and a comparison with an external-beam-deceleration-based plasma potential determination will be presented.