IPAC2021 - List of Keywords (PLC)

Paper	Title	Other Keywords	Page
TUPAB314	SPS Personnel Protection System: From Design to Commissioning	site, controls, operation, MMI	2224
	T. Ladzinski, T. Hakulinen, F. Havart, V. Martins De Sousa Dos Rios, M. Munoz Codoceo, P. Ninin, J.P. Ridewood, E. Sanchez-Corral Mena, D. Vaxelaire CERN, Meyrin, Switzerland
	During the second long shutdown (LS2) of the accelerator complex at CERN, the access system of the Super Proton Synchrotron (SPS) was completely renovated. This complex project was motivated by the technical obsolescence and lack of sufficient redundancy in the existing system, as well as by the need for homogenisation of technologies and practices across the different machines at CERN. The new Personnel Protection System includes 16 state-of-the-art access points making sure that only fully identified, trained and authorised personnel can enter the facility and an interlock system with a rationalized number of safety chains designed to meet the current safety standards. The control part is based on Siemens 1500 series of programmable logic controllers, complemented by a technologically diverse relay logic loop for the critical safety functions. This paper presents the new system and the design choices made to permit fast installation in a period where the access system itself was heavily used to allow vast upgrades of the SPS accelerator and its infrastructure. It also covers the verification and validation methodology and lessons learned during the commissioning phase.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB314
About •	paper received ※ 14 May 2021 paper accepted ※ 10 June 2021 issue date ※ 22 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAB319	SNS Credited Beam Power Limit System Preliminary Design	timing, target, controls, dipole	2242
	C. Deibele ORNL, Oak Ridge, Tennessee, USA K.L. Mahoney ORNL RAD, Oak Ridge, Tennessee, USA
	The Controls Group at the Spallation Neutron Source (SNS) is designing a programmable signal processor based credited safety control that calculates pulsed beam power based on beam kinetic energy and charge. The system must reliably shut off the beam if the average power exceeds 2.145 MW averaged over 60 seconds. This paper discusses architecture and design choices needed to develop the system under the auspices of a programmable radiation-safety credit control.
	Poster TUPAB319 [1.925 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB319
About •	paper received ※ 16 May 2021 paper accepted ※ 02 July 2021 issue date ※ 25 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAB322	Redesign and Upgrade of the LHC Access Control System	controls, site, interface, hardware	2249
	T. Hakulinen, S. Di Luca, G. Godineau, R. Nunes, G. Smith CERN, Meyrin, Switzerland
	The old LHC Access Control System (LACS) was based on a single access control solution, which integrated software and hardware into one monolithic application encompassing all the different subsystems (access control, video surveillance, interphones, biometry, equipment control, safety elements). Both the hardware and software were approaching end-of-life by the vendor before the CERN Long Shutdown 2 (LS2). The new design is based on a distributed approach, where the different subsystems are integrated in a flexible manner with well-defined interfaces, which will permit much easier single sub-system management, upgrades, and even full replacements if necessary. From the system point of view, the focus is on the advantages that this redesign brings to system operation, testing, and management. Procedurally the interest is in the overall management of a very complex in-place upgrade of a system, where the new implementation needed to coexist with the old during its constant simultaneous solicitation over the LS2.
	Poster TUPAB322 [6.906 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB322
About •	paper received ※ 15 May 2021 paper accepted ※ 28 May 2021 issue date ※ 28 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAB353	Remote Commissioning of 400 kW 352 MHz Amplifiers	controls, power-supply, real-time, MMI	2332
	C. Pasotti, A. Cuttin, A. Fabris Elettra-Sincrotrone Trieste S.C.p.A., Basovizza, Italy A. Frizzi, G. Zardi Itelco Broadcast Srl, Orvieto (TR), Italy M. Rossi DB Science, Padova, Italy
	In the framework of the European Spallation Source ERIC (ESS ERIC) In-Kind collaboration, Elettra Sincrotrone Trieste has the task to deliver 26 400 kW 352 MHz Radio Frequency Power Station (RFPS) units. They will feed the Spoke Cavities section of the proton Linac. The RFPS manufacturing contract has been awarded to the European Science Solutions consortium (ESS-C) gained the. The production of the amplifiers is well underway and it has reached a steady rate of delivery. Each RFPS is subject to a Factory Acceptance Test (FAT). In this contribution, the main results of the FATs are presented, together with the FAT remote session protocol. This protocol has been specifically developed to cope with the traveling and in persons meeting restrictions imposed by the COVID-19 pandemic.
	Poster TUPAB353 [2.675 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB353
About •	paper received ※ 17 May 2021 paper accepted ※ 23 June 2021 issue date ※ 17 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAB354	352-MHz Solid State RF System Development at the Advanced Photon Source	cavity, GUI, controls, klystron	2335
	D. Horan, D.J. Bromberek, N.P. DiMonte, A. Goel, T.J. Madden, A. Nassiri, G. Trento, G.J. Waldschmidt ANL, Lemont, Illinois, USA
	Development effort is underway on a 352MHz, 200kW solid state rf system intended as the base design to replace the existing klystron-based rf systems presently in use at the Advanced Photon Source (APS). A sixteen-input, 200kW final combining cavity was designed, built, and successfully tested to 29kW CW in combiner mode, and to 200kW CW in back-feed mode, where an external klystron was used to transmit power into the combining cavity. A four-port waveguide combiner was also tested in both backfeed and combiner mode to 193kW and 26kW respectively. Slow and fast interlock systems were designed and implemented to support the testing process. An EPICS and Programmable Logic Controller (PLC)-based system was developed to control, communicate with, and monitor the rf amplifiers used in the combiner-mode test, and to monitor and log system performance parameters relating to the combining cavity. Low-level rf control of the cavity in 29kW combiner-mode operation was achieved using the existing APS analog low-level rf hardware. Test data and design details are presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB354
About •	paper received ※ 18 May 2021 paper accepted ※ 31 May 2021 issue date ※ 19 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAB394	Development of a New Interlock and Data Acquisition for the RF System at High Energy Photon Source	controls, EPICS, cavity, FPGA	3630
	Z.W. Deng, J.P. Dai, H.Y. Lin, Q.Y. Wang, P. Zhang IHEP, Beijing, People’s Republic of China
	Funding: This work was supported by High Energy Photon Source, a major national science and technology infrastructure in China. A new interlock and data acquisition (DAQ) system is being developed for the RF system at High Energy Photon Source (HEPS) to protect essential devices as well as to locate the fault. Various signals collected and pre-processed by the DAQ system and individual interlock signals from solid-state power amplifiers, low-level RFs, arc detectors, etc. are sent to the interlock system for logic decision to control the RF switch. Programmable logic controllers (PLC) are used to collect slow signals like temperature, water flowrate, etc., while fast acquisition for RF signals is realized by dedicated boards with down-conversion frontend and digital signal processing boards. In order to improve the response time, field programmable gate array (FPGA) has been used for interlock logic implementation with an embedded experimental physics and industrial control system (EPICS). Data storage is managed by using EPICS Archiver Appliance and an operator interface is developed by using Control System Studio (CSS) running on a standalone computer. This paper presents the design and the first test of the new interlock and DAQ for HEPS RF system.
	Poster WEPAB394 [2.140 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-WEPAB394
About •	paper received ※ 16 May 2021 paper accepted ※ 14 July 2021 issue date ※ 31 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Other Keywords

Page

TUPAB314

SPS Personnel Protection System: From Design to Commissioning

site, controls, operation, MMI

2224

T. Ladzinski, T. Hakulinen, F. Havart, V. Martins De Sousa Dos Rios, M. Munoz Codoceo, P. Ninin, J.P. Ridewood, E. Sanchez-Corral Mena, D. Vaxelaire
CERN, Meyrin, Switzerland

During the second long shutdown (LS2) of the accelerator complex at CERN, the access system of the Super Proton Synchrotron (SPS) was completely renovated. This complex project was motivated by the technical obsolescence and lack of sufficient redundancy in the existing system, as well as by the need for homogenisation of technologies and practices across the different machines at CERN. The new Personnel Protection System includes 16 state-of-the-art access points making sure that only fully identified, trained and authorised personnel can enter the facility and an interlock system with a rationalized number of safety chains designed to meet the current safety standards. The control part is based on Siemens 1500 series of programmable logic controllers, complemented by a technologically diverse relay logic loop for the critical safety functions. This paper presents the new system and the design choices made to permit fast installation in a period where the access system itself was heavily used to allow vast upgrades of the SPS accelerator and its infrastructure. It also covers the verification and validation methodology and lessons learned during the commissioning phase.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB314

About •

paper received ※ 14 May 2021 paper accepted ※ 10 June 2021 issue date ※ 22 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAB319

SNS Credited Beam Power Limit System Preliminary Design

timing, target, controls, dipole

2242

C. Deibele
ORNL, Oak Ridge, Tennessee, USA
K.L. Mahoney
ORNL RAD, Oak Ridge, Tennessee, USA

The Controls Group at the Spallation Neutron Source (SNS) is designing a programmable signal processor based credited safety control that calculates pulsed beam power based on beam kinetic energy and charge. The system must reliably shut off the beam if the average power exceeds 2.145 MW averaged over 60 seconds. This paper discusses architecture and design choices needed to develop the system under the auspices of a programmable radiation-safety credit control.

Poster TUPAB319 [1.925 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB319

About •

paper received ※ 16 May 2021 paper accepted ※ 02 July 2021 issue date ※ 25 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAB322

Redesign and Upgrade of the LHC Access Control System

controls, site, interface, hardware

2249

T. Hakulinen, S. Di Luca, G. Godineau, R. Nunes, G. Smith
CERN, Meyrin, Switzerland

The old LHC Access Control System (LACS) was based on a single access control solution, which integrated software and hardware into one monolithic application encompassing all the different subsystems (access control, video surveillance, interphones, biometry, equipment control, safety elements). Both the hardware and software were approaching end-of-life by the vendor before the CERN Long Shutdown 2 (LS2). The new design is based on a distributed approach, where the different subsystems are integrated in a flexible manner with well-defined interfaces, which will permit much easier single sub-system management, upgrades, and even full replacements if necessary. From the system point of view, the focus is on the advantages that this redesign brings to system operation, testing, and management. Procedurally the interest is in the overall management of a very complex in-place upgrade of a system, where the new implementation needed to coexist with the old during its constant simultaneous solicitation over the LS2.

Poster TUPAB322 [6.906 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB322

About •

paper received ※ 15 May 2021 paper accepted ※ 28 May 2021 issue date ※ 28 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAB353

Remote Commissioning of 400 kW 352 MHz Amplifiers

controls, power-supply, real-time, MMI

2332

C. Pasotti, A. Cuttin, A. Fabris
Elettra-Sincrotrone Trieste S.C.p.A., Basovizza, Italy
A. Frizzi, G. Zardi
Itelco Broadcast Srl, Orvieto (TR), Italy
M. Rossi
DB Science, Padova, Italy

In the framework of the European Spallation Source ERIC (ESS ERIC) In-Kind collaboration, Elettra Sincrotrone Trieste has the task to deliver 26 400 kW 352 MHz Radio Frequency Power Station (RFPS) units. They will feed the Spoke Cavities section of the proton Linac. The RFPS manufacturing contract has been awarded to the European Science Solutions consortium (ESS-C) gained the. The production of the amplifiers is well underway and it has reached a steady rate of delivery. Each RFPS is subject to a Factory Acceptance Test (FAT). In this contribution, the main results of the FATs are presented, together with the FAT remote session protocol. This protocol has been specifically developed to cope with the traveling and in persons meeting restrictions imposed by the COVID-19 pandemic.

Poster TUPAB353 [2.675 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB353

About •

paper received ※ 17 May 2021 paper accepted ※ 23 June 2021 issue date ※ 17 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAB354

352-MHz Solid State RF System Development at the Advanced Photon Source

cavity, GUI, controls, klystron

2335

D. Horan, D.J. Bromberek, N.P. DiMonte, A. Goel, T.J. Madden, A. Nassiri, G. Trento, G.J. Waldschmidt
ANL, Lemont, Illinois, USA

Development effort is underway on a 352MHz, 200kW solid state rf system intended as the base design to replace the existing klystron-based rf systems presently in use at the Advanced Photon Source (APS). A sixteen-input, 200kW final combining cavity was designed, built, and successfully tested to 29kW CW in combiner mode, and to 200kW CW in back-feed mode, where an external klystron was used to transmit power into the combining cavity. A four-port waveguide combiner was also tested in both backfeed and combiner mode to 193kW and 26kW respectively. Slow and fast interlock systems were designed and implemented to support the testing process. An EPICS and Programmable Logic Controller (PLC)-based system was developed to control, communicate with, and monitor the rf amplifiers used in the combiner-mode test, and to monitor and log system performance parameters relating to the combining cavity. Low-level rf control of the cavity in 29kW combiner-mode operation was achieved using the existing APS analog low-level rf hardware. Test data and design details are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB354

About •

paper received ※ 18 May 2021 paper accepted ※ 31 May 2021 issue date ※ 19 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAB394

Development of a New Interlock and Data Acquisition for the RF System at High Energy Photon Source

controls, EPICS, cavity, FPGA

3630

Z.W. Deng, J.P. Dai, H.Y. Lin, Q.Y. Wang, P. Zhang
IHEP, Beijing, People’s Republic of China

Funding: This work was supported by High Energy Photon Source, a major national science and technology infrastructure in China.
A new interlock and data acquisition (DAQ) system is being developed for the RF system at High Energy Photon Source (HEPS) to protect essential devices as well as to locate the fault. Various signals collected and pre-processed by the DAQ system and individual interlock signals from solid-state power amplifiers, low-level RFs, arc detectors, etc. are sent to the interlock system for logic decision to control the RF switch. Programmable logic controllers (PLC) are used to collect slow signals like temperature, water flowrate, etc., while fast acquisition for RF signals is realized by dedicated boards with down-conversion frontend and digital signal processing boards. In order to improve the response time, field programmable gate array (FPGA) has been used for interlock logic implementation with an embedded experimental physics and industrial control system (EPICS). Data storage is managed by using EPICS Archiver Appliance and an operator interface is developed by using Control System Studio (CSS) running on a standalone computer. This paper presents the design and the first test of the new interlock and DAQ for HEPS RF system.

Poster WEPAB394 [2.140 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-WEPAB394

About •

paper received ※ 16 May 2021 paper accepted ※ 14 July 2021 issue date ※ 31 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)