ANL, Argonne, USA
During the design of the 60.635 MHz RFQ for the ATLAS efficiency and intensity upgrade*, we have established a new full 3D approach for the electromagnetic and beam dynamics simulations of a RFQ. A Detailed full 3D model (four meter long) including vane modulation was built and simulated using CST Microwave Studio, which is made possible by the ever advancing computing capabilities. The approach was validated using experimental measurements on a prototype 57.5 MHz RFQ**. The effects of the radial matchers, vane modulation and tuners on the resonant frequency and field flatness have been carefully studied. The full 3D field distribution was used for beam dynamics simulations using both CST Particle Studio and the beam dynamics code TRACK***. In the final design we have used trapezoidal modulation instead of the standard sinusoidal in the accelerating section of the RFQ to achieve more energy gain for the same length, following the leading work of the Protvino group****. In our case, the output energy increased from 260 keV/u to 295 keV/u with minimal change in the beam dynamics.
* P.N. Ostroumov et al, Proceedings of LINAC-2010
** P.N. Ostroumov et al, Proceedings of LINAC-2006
*** TRACK @ http://www.phy.anl.gov/atlas/TRACK
**** O.K. Belyaev et al, Proceedings of LINAC-2000
ESS Bilbao, Bilbao, Spain
Bilbao, Faculty of Science and Technology, Bilbao, Spain
University of the Basque Country, Faculty of Science and Technology, Bilbao, Spain
ESS-Bilbao, Zamudio, Spain
Imperial College of Science and Technology, Department of Physics, London, United Kingdom
STFC/RAL/ISIS, Chilton, Didcot, Oxon, United Kingdom
The Bilbao Accelerator RFQ is aimed to accelerate a 75 mA proton beam from 75 keV to 3 MeV, while keeping the beam both transversely and longitudinally focused, and presenting a minimum emittance growth. We report on the current status of the project, mainly focusing on the Beam Dynamics aspects of the design. Several particle simulations are carried out with RFQSIM, GPT and TRACK codes, in order to study the particle transmission of the RFQ under several circumstances, such as different current levels, vane geometry changes due to thermal stress, and different input beam characteristics obtained by changing the LEBT operation settings.
ESS, Lund, Sweden
Fermilab, Batavia, USA
NSCL, East Lansing, Michigan, USA
FRIB, East Lansing, Michigan, USA
The driver linac for the Facility for Rare Isotope Beams (FRIB) at MSU will produce primary beams of ions at ≥200 MeV/u for nuclear physics research. A dc ion beam from an ECR ion source will be pre-bunched upstream of the radio frequency quadrupole linac. A multi-harmonic buncher (MHB) was designed for this purpose, using experience gained with a similar buncher for the ReA3 re-accelerator linac, which is presently being commissioned at MSU. The FRIB MHB resonator operates with three frequencies (40.25 MHz, 80.5 MHz, and 120.75 MHz) to produce an approximately linear sawtooth in the voltage as a function of time. The three resonant frequencies are produced via two quarter-wave resonators with a common gridless gap: one resonator is driven at its fundamental mode at 40.25 MHz and its first higher-order mode (120.75 MHz), while the other is driven only at its fundamental mode of 80.5 MHz. The electromagnetic design of the MHB resonator will be presented, including the electrode design and tuning mechanisms.
AES, Medford, NY, USA
ANL, Argonne, USA
TechSource, Santa Fe, New Mexico, USA
The upgrade for the ATLAS facility is designed to increase the efficiency and intensity of beams for the user facility*, **. This will be accomplished with a new CW normal conducting RFQ, which will increase both transverse and longitudinal acceptance of the LINAC. This RFQ must operate over a wide range of power levels to accelerate ion species from protons to uranium. The RFQ design is a split coaxial structure and is made of OFE copper. The geometry of the design must be stable during operation. Engineering studies of the design at different RF power levels were conducted to ensure that the geometry requirements were met. Frequency shift analysis was also completed to determine the effects of high power levels. Thermal stress analysis was completed to show that the structure frequency is repeatable.
*P.N. Ostroumov, et.al, “A New Atlas Efficiency and Intensity Upgrade Project,” SRF2009, tuppo016
**P.N. Ostroumov, et.al., “Efficiency and Intensity Upgrade of the Atlas Facility,” LINAC 2010, MOP045
IAP, Frankfurt am Main, Germany
Fermilab, Batavia, USA
This paper describes the construction and operational status of an accelerator test facility for Project X. The purpose of this facility is for Project X component development activities that benefit from beam tests and any development activities that require 325 MHz or 650 MHz RF power. It presently includes an H- beam line, a 325 MHz superconducting cavity test facility, a 325 MHz (pulsed) RF power source, and a 650 MHz (CW) RF power source. The paper also discusses some specific Project X components that will be tested in the facility.
ESS Bilbao, Bilbao, Spain
Bilbao, Faculty of Science and Technology, Bilbao, Spain
University of the Basque Country, Faculty of Science and Technology, Bilbao, Spain
ESS-Bilbao, Zamudio, Spain
In this work we present a future upgrade of the ESS-Bilbao multi-source Low Energy Transport System (LEBT). It consists of a set of solenoids and steering dipoles used to match the characteristics of both ion source beams i.e., the Electron Cyclotron Resonance (ECR) H+/D+ source and the H− Penning source, to the input specifications of the RFQ. Different configurations of the geometry and magnetic fields are studied in order to minimize the emittance growth along the LEBT, while providing the beam specifications required by the RFQ.
ORNL RAD, Oak Ridge, Tennessee, USA
ORNL, Oak Ridge, Tennessee, USA
Fermilab, Batavia, USA
IAP, Frankfurt am Main, Germany
IAP, Frankfurt am Main, Germany
Funneling is a method to increase low energy beam currents in multiple stages. The Frankfurt Funneling Experiment is a model of such a stage. The experiment is built up of two ion sources with electrostatic lens systems, a Two-Beam-RFQ accelerator, a funneling deflector and a beam diagnostic system. The two beams are bunched and accelerated in a Two-Beam RFQ. A funneling deflector combines the bunches to a common beam axis. Current work is the construction and beam tests of a new beam transport system between RFQ accelerator and deflector. With extended RFQ-electrodes the drift between the Two-Beam-RFQ and the rf-deflector will be minimized and therefore unwanted emittance growth reduced. First rf-measurements with the improved Two-Beam-RFQ will be presented.
IAP, Frankfurt am Main, Germany
NSCL, East Lansing, Michigan, USA
Kress GmbH, Biebergemuend, Germany
GSI, Darmstadt, Germany
FRIB, East Lansing, Michigan, USA
IAP, Frankfurt am Main, Germany
The Facility for Rare Isotope Beams (FRIB) is currently in the preliminary design phase at Michigan State University (MSU). FRIB consists of a driver LINAC for the acceleration of heavy ion beams, followed by a fragmentation target station and a ReAccelerator facility (ReA3). ReA3 comprises gas stopper systems, an Electron Beam Ion Trap (EBIT) charge state booster, a room temperature radio frequency quadrupole (RFQ), a LINAC using superconducting quarter wave resonators and an achromatic beam transport and distribution line to the new experimental area. Beams from ReA3 will range from 3 MeV/u for heavy ions to about 6 MeV/u for light ions. The ReA3 RFQ, which is of the 4 rod type, is designed to accelerate ions with an Q/A of 0.2 to 0.5 from 12 keV/u to 600 keV/u. The RFQ operates at a frequency of 80.5 MHz and power levels up to 120 kW at 10% duty factor. In this paper we will report on commissioning results from the ReA3 RFQ using a H2+ and He+ beam from an auxiliary ion source.
Fermilab, Batavia, USA
Project X, under study at Fermilab, is a multi task SRF beam facility, aiming to provide high intensity protons for rare processes experiments and nuclear physics at low energy, and simultaneously for the production of neutrinos, as well as muon beams in the long term. A beam test facility - former known as High Intensity Neutrino Source (HINS) - is under commissioning for testing critical components of the project, e.g. a beam chopper. In this paper we describe the layout of the test facility and present beam dynamics simulations and measurements.
BNL, Upton, Long Island, New York, USA
IAP, Frankfurt am Main, Germany
The construction and initial commissioning phase of a new heavy ion preinjector was completed at Brookhaven in September, 2010, and the preinjector is now operational. This preinjector, using an EBIS source to produce high charge state heavy ions, provided helium and neon ion beams for use at the NASA Space Radiation Laboratory in the Fall of 2010, and gold and uranium beams are being commissioned during the 2011 run cycle for use in RHIC. The EBIS operates with an electron beam current of up to 10 A, to produce mA level currents in 10 to 40 μs beam pulses. The source is followed by an RFQ and IH linac to accelerate ions with q/m > 0.16 to an energy of 2 MeV/amu, for injection into the Booster synchrotron. The performance of the preinjector is presented, including initial operational experience for the NASA and RHIC programs.
BNL, Upton, Long Island, New York, USA
After reconfiguration of the low energy (35 keV) and the medium energy (750 keV) transport lines in 2009-10, the Brookhaven linac is now delivering the highest intensity beam since it was built in 1970 (~120 μA average current of H− to the Brookhaven Linac Isotope Producer). It is also now delivering lower emittance polarized H− ion beam for the polarized program at RHIC. To increase the intensity further, we are replacing the buncher in the 750 keV line with one with higher Q value, to allow operation at higher power. Also, to improve polarization, we are replacing the magnetic solenoid before the RFQ in the 35 keV line by a solenoid-einzel lens combination. The paper will report on the results of these changes.
ORNL, Oak Ridge, Tennessee, USA
ORNL RAD, Oak Ridge, Tennessee, USA
Running routinely with ~40-mA, 1-MW beams, the SNS linac is fed from the ion source with ~1ms long, ~50-mA H− beam pulses at 60 Hz. This requires the daily extraction of ~230 C of H− ions, which exceeds the routine daily production of other H− accelerator sources by almost an order of magnitude. The source service cycle has been extended from 2, to 3, to 4, and up to 5.6 weeks without age-related failures. The 7-9 kC of H− ions delivered in single service cycles exceed the service cycle yields of other accelerator sources. The paper discusses the findings as well as the issues and their mitigations, which enabled the simultaneous increase of the beam current, the duty factor, the availability, and the service cycle.
ORNL, Oak Ridge, Tennessee, USA
ORNL RAD, Oak Ridge, Tennessee, USA
ANL, Argonne, USA
ATLAS (Argonne Tandem Linac Accelerator System) upgrade requires several substantial developments in accelerator technologies, such as CW heavy ion RFQ and high-performance cryomodule with low-beta cavities. The upgrade project is well advanced. The physics and engineering design of the RFQ are complete and fabrication of OFE copper parts is in progress. The 3.9-meter length RFQ is composed from 5 strongly coupled segments. High-temperature furnace brazing of the segments is planned for the summer of 2011. The RFQ design includes several innovative features such as trapezoidal vane tip modulation, compact output radial matcher to form an axially symmetric beam. The upgrade project also includes development and construction of a cryomodule containing seven 72.75 MHz SC quarter wave cavities designed for the geometrical β= 0.077 and four SC solenoids. The cavity is designed to obtain an accelerating voltage higher than 2.5 MV. The prototype cavity together with high-power capacitive coupler and piezoelectric tuner has been developed, fabricated and is being tested. This paper reports innovative design features of both RFQ and SRF linac and current status of the project.