BNL, Upton, New York, USA
In order to minimize the systematic errors for the Relativistic Heavy Ion Collider (RHIC) spin physics experiments, flipping the spin of each bunch of protons during the stores is needed. Experiments done with single RF magnet at energies less than 2 GeV have demonstrated a spin-flip efficiency over 99%. At high energy colliders with Siberian snakes, a single magnet spin flipper does not work because of the large spin tune spread and the generation of multiple, overlapping resonances. Over past decade, RHIC spin flipper design has evolved and a sophisticated spin flipper, constructed of nine-dipole magnets, was developed to flip the spin in RHIC. A special optics choice was also used to make the spin tune spread very small. In recent experiment, 97% spin-flip efficiency was measured at both 24 and 255 GeV for the first time. The results show that efficient spin flipping can be achieved at high energies.
BNL, Upton, New York, USA
The physics program in the EIC calls for polarized neutron beam at high energies. The best neutron carriers are 3He nuclei and deuterons. Both neutron carries are expected to be used by spin physics program in the EIC. Due to the small magnetic moment anomaly of deuteron particles, much higher magnetic fields are required for spin rotation, so full Siberian snake is not feasible. However, the resonance strength is in general weak and the number of resonances is also small. It is possible to deal with individual resonances with conventional methods, such as betatron tune jump for intrinsic depolarizing resonances; and a weak partial snakes for imperfection resonances. The study shows that accelerating polarized deuteron beyond 100GeV/n is possible in the EIC.
BNL, Upton, New York, USA
JLab, Newport News, Virginia, USA
Douglas Consulting, York, Virginia, USA
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
Xelera Research LLC, Ithaca, New York, USA
The Electron-Ion Collider will achieve a luminosity of 1034 cm-2 s−1 by incorporating strong hadron cooling to counteract hadron Intra-Beam Scattering, using a coherent electron cooling scheme. An accelerator will deliver the beams with key parameters, such as 1 nC bunch charge, and 1e-4 energy spread. The paper presents the design and beam dynamics simulation results. Methods to minimize beam noise, the challenges of the accelerator design, and the R&D topics being pursued are discussed.
JLab, Newport News, Virginia, USA
BNL, Upton, New York, USA
ODU, Norfolk, Virginia, USA
SBU, Stony Brook, New York, USA
The possibility of two interaction regions (IRs) is a design requirement for Electron-Ion Collider (EIC). There is also a significant interest from the nuclear physics community to have a 2nd IR with measurement capabilities complementary to those of the 1st IR. While the 2nd IR will be in operation over the entire energy range of ~20GeV to ~140GeV center of mass (CM). The 2nd IR can also provide an acceptance coverage complementary to that of the 1st. In this paper, we present a brief overview and the current progress of the 2nd IR design in terms of the parameters, magnet layout, and beam dynamics.
BNL, Upton, New York, USA
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
JLab, Newport News, Virginia, USA
The Electron Ion Collider will collide hadrons in the Hadron Storage Ring (HSR) with ultra-relativistic electrons in the Electron Storage Ring. The HSR design trajectory includes a large radial shift over a large fraction of its circumference, in order to adjust the hadron path length to synchronize collisions over a broad range of hadron energies. The design trajectory goes on-axis through the magnets, crab cavities and other components in the six HSR Insertion Regions. This paper discusses the issues involved and reports on past and future beam experiments in the Relativistic Heavy Ion Collider, which will be upgraded to become the HSR.
BNL, Upton, New York, USA
The Electon Ion Collider (EIC) hadron ring will use the existing Relativistic Heavy Ion Collider storage rings, including the superconducting magnet arcs. The vacuum chambers in the superconducting magnets and the cold mass interconnects were not designed for EIC beams and so must be updated to reduce its resistive-wall heating and to suppress electron clouds. To do so without compromising the EIC luminosity goal, a stainless steel beam screen with co-laminated copper and a thin layer of amorphous carbon will be installed. This paper describes the main requirements that our solution for the hadron ring vacuum chamber needs to satisfy, including impedance, aperture limitations, vacuum, thermal and structural stability, mechanical design, installation and operation. The conceptual design of the beam screen currently under development is introduced.
BNL, Upton, New York, USA
JLab, Newport News, USA
SLAC, Menlo Park, California, USA
This paper presents an overview of the Interaction Region (IR) design for the planned Electron-Ion Collider (EIC) at Brookhaven National Laboratory. The IR is designed to meet the requirements of the nuclear physics community *. The IR design features a ±4.5 m free space for the detector; a forward spectrometer magnet is used for the detection of hadrons scattered under small angles. The hadrons are separated from the neutrons allowing detection of neutrons up to ±4 mrad. On the rear side, the electrons are separated from photons using a weak dipole magnet for the luminosity monitor and to detect scattered electrons (e-tagger). To avoid synchrotron radiation backgrounds in the detector no strong electron bending magnet is placed within 40 m upstream of the IP. The magnet apertures on the rear side are large enough to allow synchrotron radiation to pass through the magnets. The beam pipe has been optimized to reduce the impedance; the total power loss in the central vacuum chamber is expected to be less than 90 W. To reduce risk and cost the IR is designed to employ standard NbTi superconducting magnets, which are described in a separate paper.
* An Assessment of U.S.-Based Electron-Ion Collider Science. (2018). Washington, D.C.: National Academies Press. https://doi.org/10.17226/25171
BNL, Upton, New York, USA
JLab, Newport News, Virginia, USA
The electron-ion luminosity in EIC has a number of limits, including the ion intensity available from the injectors, the total ion beam current, the electron bunch intensity, the total electron current, the synchrotron radiation power, the beam-beam effect, the achievable beta functions at the interaction points (IPs), the maximum angular spreads at the IP, the ion emittances reachable with stochastic or strong cooling, the ratio of horizontal to vertical emittance, and space charge effects. We map the e-A luminosity over the center-of-mass energy range for some ions ranging from deuterons to uranium ions. For e-Au collisions the present design provides for electron-nucleon (e-Au) peak luminosities of 1.7x1033 cm-2s−1 with stochastic cooling, and 4.7x1033 cm-2s−1 with strong hadron cooling.
BNL, Upton, New York, USA
JLab, Newport News, Virginia, USA
SLAC, Menlo Park, California, USA
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
Fermilab, Batavia, Illinois, USA
ODU, Norfolk, Virginia, USA
FRIB, East Lansing, Michigan, USA
The design of the electron-ion collider EIC to be constructed at Brookhaven National Laboratory has been continuously evolving towards a realistic and robust design that meets all the requirements set forth by the nuclear physics community in the White Paper. Over the past year activities have been focused on maturing the design, and on developing alternatives to mitigate risk. These include improvements of the interaction region design as well as modifications of the hadron ring vacuum system to accommodate the high average and peak beam currents. Beam dynamics studies have been performed to determine and optimize the dynamic aperture in the two collider rings and the beam-beam performance. We will present the EIC design with a focus on recent developments.
BNL, Upton, New York, USA
FRIB, East Lansing, Michigan, USA
ODU, Norfolk, Virginia, USA
JLab, Newport News, Virginia, USA
LBNL, Berkeley, California, USA
The design luminosity goal for the Electron-Ion Collider (EIC) is 1e34 cm-2s−1. To achieve such a high luminosity, the EIC design adopts high bunch intensities, flat beams at the interaction point (IP) with a small vertical β*-function, and a high collision frequency, together with crab cavities to compensate the geometrical luminosity loss due to the large crossing angle of 25mrad. In this article, we present our strategies and approaches to obtain the design luminosity by optimizing some key beam-beam related design parameters. Through our extensive strong-strong and weak-strong beam-beam simulations, we found that beam flatness, electron and proton beam size matching at the IP, electron and proton working points, and synchro-betatron resonances arising from the crossing angle collision play a crucial role in proton beam size growth and luminosity degradation. After optimizing those parameters, we found a set of beam-beam related design parameters to reach the design luminosity with an acceptable beam-beam performance.
BNL, Upton, New York, USA
FRIB, East Lansing, Michigan, USA
ODU, Norfolk, Virginia, USA
JLab, Newport News, Virginia, USA
LBNL, Berkeley, California, USA
The Electron-Ion Collider (EIC) is aiming at a design luminosity of 1e34 cm-2s−1. To maintain such a high luminosity, both beams in the EIC need an acceptable beam lifetime in the presence of the beam-beam interaction. For this purpose, we carried out weak-strong element-by-element particle tracking to evaluate the long-term dynamic aperture for the hadron ring lattice design. We improved our simulation code SimTrack to treat some new lattice design features, such as radially offset on-momentum orbits, coordinate transformations in the interaction region, etc. In this article, we will present the preliminary dynamic aperture calculation results with β*- function scan, radial orbit shift, crossing angle collision, and magnetic field errors.
BNL, Upton, New York, USA
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
JLab, Newport News, Virginia, USA
Polarization lifetime for He3 using two and six snakes are studied using the T-BMT Spin Resonance Tracker code. This code integrates a reduced spinor form of the T-BMT equation including only several spin resonances and the kinematics of synchrotron motion. It was previously benchmarked against RHIC polarization lifetime under the two snake system *.
* Phys. Rev.Accel. Beams 22 (2019) 9, 091001