IBIC2018 - List of Keywords (storage-ring)

Paper	Title	Other Keywords	Page
MOPB09	Comparison Among Different Tune Measurement Schemes at HLS-II Storage Ring	betatron, detector, pick-up, experiment	93
	L.T. Huang, X.Y. Liu, P. Lu, M.X. Qian, B.G. Sun, J.G. Wang, J.H. Wei, F.F. Wu, Y.L. Yang, T.Y. Zhou USTC/NSRL, Hefei, Anhui, People’s Republic of China
	Tune measurement is one of the most significant beam diagnostics at HLS-II storage ring. When measuring tune, higher tune spectral component and lower other compo-nents are expected, so that the tune measurement will be more accurate. To this end, a set of BBQ (Base Band Tune) front-end based on 3D (Direct Diode Detection) technique has previously developed to improve the effec-tive signal content and suppress other components. Em-ploying the BBQ front-end, four different tune measure-ment schemes are designed and related experiments per-formed on the HLS-II storage ring. Experimental results and analysis will be presented later.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPB09
About •	paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPB14	SSRF Beam Operation Stability Evaluation Using Bunch by Bunch Beam Position Method	injection, SRF, operation, damping	104
	N. Zhang SSRF, Shanghai, People’s Republic of China Y.B. Leng, Y.M. Zhou SINAP, Shanghai, People’s Republic of China
	Funding: Work supported by National Natural Science Foundation of China (No.11575282 No.11375255 No.11305253) In order to improve the efficiency and quality of light in top-up mode at SSRF, disturbance caused by leakage fields mismatch during injection should be minimized and stable. This could be evaluated by analysis of bunch by bunch residual betatron oscillation data, using this method, instability of tune distribution and damping repeatability could also be calculated. So we could evaluate the beam operation stability by the data analysis and discuss in the paper.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPB14
About •	paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPC02	Identification of Faulty Beam Position Monitor Based Clustering by Fast Search and Find of Density Peaks	SRF, electron, electronics, operation	114
	R. Jiang, Y.B. Leng SSRF, Shanghai, People’s Republic of China F.Z. Chen, Z.C. Chen, Y.B. Leng SINAP, Shanghai, People’s Republic of China
	The accuracy and stability of beam position moni-tors(BPMs) are important for all kinds of measurement systems and feedback systems in particle accelerator field. A proper method detecting faulty beam position monitor or monitoring their stability could optimize accel-erator operating conditions. With development in ma-chine learning methods, a series of powerful analysis approaches make it possible for detecting beam position monitor’s stability. Here, this paper proposed a clustering analysis approach to detect the defective BPMs. The method is based on the idea that cluster centres are char-acterized by a higher density than their neighbours and by a relatively large distance from points with higher densi-ties. The results showed that clustering by fast search and find of density peaks could classify beam data into dif-ferent clusters on the basis of their similarity. And that, aberrant data points could be detected by decision graph. So the algorithm is appropriate for BPM detecting and it could be a significant supplement for data analysis in accelerator physics.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPC02
About •	paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPC03	Precise Measurement of Small Currents at the MLS	electron, radiation, experiment, synchrotron	118
	Y. Petenev, J. Feikes, J. Li, A.N. Matveenko, Y. Tamashevich HZB, Berlin, Germany R. Klein, J. Lubeck, R. Thornagel PTB, Berlin, Germany
	The Physikalisch-Technische Bundesanstalt (PTB), the National Metrology Institute of Germany, utilizes an electron storage ring - the Metrology Light Source (MLS), located in Berlin, as a radiation source standard in the VIS, UV and VUV spectral range. In order to be able to calculate the absolute intensity of the radiation, the electron beam current has to be measured with low uncertainty. In this paper we focus on the measurement of the beam current in a range of several nA to 1 pA (one electron) by means of Si photodiodes, detecting synchrotron radiation from the beam. Electrons are gradually scraped out of the ring and the diode signal is analyzed afterwards. The exact number of stored electrons then can be derived from the signal. The measurement is carried out automatically with an in-house developed software.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPC03
About •	paper received ※ 04 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPC08	Beam Intensity Monitoring with nA Resolution - the Cryogenic Current Comparator (CCC)	cryogenics, antiproton, proton, shielding	130
	D.M. Haider, P. Forck, F. Kurian, M. Schwickert, T. Sieber, T. Stöhlker GSI, Darmstadt, Germany H. De Gersem, N. Marsic TEMF, TU Darmstadt, Darmstadt, Germany M.F. Fernandes, J. Tan CERN, Geneva, Switzerland J. Golm, F. Schmidl, P. Seidel FSU Jena, Jena, Germany J. Golm, T. Stöhlker, V. Tympel HIJ, Jena, Germany M. Schmelz, R. Stolz, V. Zakosarenko IPHT, Jena, Germany T. Stöhlker IOQ, Jena, Germany V. Zakosarenko Supracon AG, Jena, Germany
	Funding: Work supported by AVA - Accelerators Validating Antimatter the EU H2020 Marie-Curie Action No. 721559 and by the BMBF under contract No. 05P15SJRBA. The storage of low current beams as well as the long extraction times from the synchrotrons at FAIR require non-destructive beam intensity monitoring with a current resolution of nanoampere. To fulfill this requirement, the concept of the Cryogenic Current Comparator (CCC), based on the low temperature SQUID, is used to obtain an extremely sensitive beam current transformer. During the last years, CCCs have been installed to do measurements of the spill structure in the extraction line of GSI SIS18 and for current monitoring in the CERN Antiproton Decelerator. From these experiences lessons can be learned to facilitate further developments. The goal of the ongoing research is to improve the robustness of the CCC towards external influences, such as vibrations, stray fields and He-pressure variations, as well as to develop a cost-efficient concept for the superconducting shield and the cryostat.
	Poster MOPC08 [1.441 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPC08
About •	paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPC16	The Development and Applications of Digital BPM Signal Processor on SSRF	SRF, brilliance, controls, FEL	147
	L.W. Lai, F.Z. Chen, Y.B. Leng, Y.B. Yan, N. Zhang, W.M. Zhou SSRF, Shanghai, People’s Republic of China
	The development of Digital BPM Signal Processors (DBPM) for SSRF started from 2008. The first prototype for SSRF storage ring was completed in 2012, with turn-by-turn resolution better than 1μm. From 2016 to 2017, SSRF successively constructed two FEL facilities in China, DCLS and SXFEL test facilities. The second ver-sion DBPM was developed and used in large scale during this period to meet the requirements of signal processing for stripline BPMs and cavity BPMs. After that, we turned to the development of DBPM for SSRF storage ring based on the second version hardware, including FPGA firmware, EPICS IOC, EDM control panel. The development was completed and tests were carried out in early 2018. Test results showed that the position data is accurate and can monitor beam movement correctly, and online turn-by-turn position data resolution reaches 0.46μm. This paper will introduce the design of DBPM for the SSRF storage ring and the tests carried out to verify the data accuracy and evaluate the system performance.
	Poster MOPC16 [1.372 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPC16
About •	paper received ※ 04 September 2018 paper accepted ※ 13 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUOB03	Demonstration of a Newly Developed Pulse-by-pulse X-Ray Beam Position Monitor in SPring-8	detector, radiation, operation, ISOL	182
	H. Aoyagi, Y. Furukawa, S. Takahashi, A. Watanabe JASRI/SPring-8, Hyogo, Japan
	Funding: This work was partly supported by Japan Society for the Promotion of Science through a Grant-in-Aid for Scientific Research (c), No. 20416374 and No. 18K11943. A newly designed pulse-by-pulse X-ray beam position monitor (XBPM), which is photoemission type, has been demonstrated successfully in the SPring-8 synchrotron radiation beamline. Conventional XBPMs work in the direct-current (DC) mode, because it is difficult to measure a beam position in the pulse mode under the sever heat load condition. The key point of the design is aiming at improving heat-resistance property without degradation of high frequency property [1]. This monitor is equipped with microstripline structure for signal transmission line to achieve pulse-by-pulse beam position signal. A photocathode is titanium electrode that is sputtered on a diamond heat sink to achieve high heat resistance. We have manufactured the prototype, and demonstrated feasibility at the SPring-8 bending magnet beamline. As a result, we observed a unipolar single pulse with the pulse length of less than 1 ns FWHM and confirmed that it has pulse-by-pules position sensitivity [2]. Furthermore, this monitor can be also used in the direct-current mode with good stability and good resolution. The operational experience will be also presented. [1] http://accelconf.web.cern.ch/AccelConf/medsi2016/papers/wepe10.pdf [2] http://www.pasj.jp/web_publish/pasj2017/proceedings/PDF/THOM/THOM06.pdf
	Slides TUOB03 [2.380 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUOB03
About •	paper received ※ 31 August 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUOC04	Development of Beam Position Monitor for the SPring-8 Upgrade	electron, electronics, radiation, brilliance	204
	H. Maesaka RIKEN SPring-8 Center, Innovative Light Sources Division, Hyogo, Japan H. Dewa, T. Fujita, M. Masaki, S. Takano JASRI, Hyogo, Japan
	We are developing a new electron beam position monitor (BPM) system for the low-emittance upgrade of SPring-8. The requirements for the BPM system are: (1) a single-pass resolution of 100 µm rms for a 100 pC bunch and an electric center accuracy of 100 µm rms for the initial beam commissioning to achieve the first turn, (2) a closed-orbit distortion (COD) resolution better than 0.1 µm rms for a 100 mA stored beam and a position stability of less than 5 µm for the ultimate stability of a photon beam axis. We have completed prototypes of a precise button electrode and a BPM block to obtain high-intensity signals and sufficient mechanical accuracy while suppressing high-Q trapped modes leading to impedance and heating issues. The development of readout electronics based on the MTCA.4 standard and the evaluation of radiation-hard coaxial cables have also been conducted. The prototype BPM head was installed in the present SPring-8 storage ring for performance verification with an actual electron beam. We confirmed sufficient signal intensity, electric center accuracy, position stability, etc. by the beam test. The new BPM system is almost ready for the SPring-8 upgrade.
	Slides TUOC04 [2.126 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUOC04
About •	paper received ※ 06 September 2018 paper accepted ※ 12 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPA03	Test of New Beam Loss Monitors for SOLEIL	detector, controls, shielding, electron	215
	N. Hubert, M. El Ajjouri, D. Pédeau SOLEIL, Gif-sur-Yvette, France
	Soleil is currently testing new beam loss monitors to replace its pin-diode based existing system. The new detectors are made of plastic scintillators associated with photomultiplier and connected to Libera BLM dedicated electronics. This new detector should provide both fast (turn by turn) and slow (averaged) loss measurements, post mortem capabilities and should be less sensitive to the beam directivity compared to the pin-diodes. Different methods for a relative calibration of the modules are under investigation, either using a diode (LED) or a cesium radioactive source. Calibration results and first measurements with beam are presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUPA03
About •	paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPB04	Development of a New Button Beam-position Monitor for BESSY VSR	impedance, vacuum, resonance, operation	265
	J.G. Hwang, V. Dürr, M. Ries, A. Schälicke, G. Schiwietz, D. Wolk HZB, Berlin, Germany
	An extreme operation mode such as the BESSY-VSR conditions stimulates the development of a high accuracy bunch-by-bunch beam-position monitor (BPM) system which is compatible with the bunch-selective operation for the orbit feedback system. Such a system will also greatly benefit to accelerator R&D such as transverse resonance island buckets (TRIBs). Compensation of the long-range ringing signal produced by the combined effect of impedance mismatching inside the button and trapped TE-modes in the aluminum-oxide insulator (Al2O3) material is required essentially to improve the resolution. This is important since the ringing causes a misreading of the beam position and current of following bunches. We show the design study of a new button-type BPM to mitigate the influence of the ringing signal as well as to reduce wake losses by improving the impedance matching in the button and by replacing the insulator material.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUPB04
About •	paper received ※ 04 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPC01	Australian Synchrotron BPM Electronics Upgrade	electron, brilliance, coupling, synchrotron	297
	Y.E. Tan, R.B. Hogan AS - ANSTO, Clayton, Australia
	The storage ring at the Australian Synchrotron (AS) was originally equipped with 98 Libera Electrons. In late 2017 all 98 of the BPM electronics has been upgraded to Libera Brilliance⁺ and the old Libera Electrons have been moved to the injection system. The transition process and results from commissioning the new system will be presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUPC01
About •	paper received ※ 05 September 2018 paper accepted ※ 13 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPC12	Beam Transverse Quadrupole Oscillation Measurement in the Injection Stage for the HLS-II Storage Ring	quadrupole, injection, betatron, electron	325
	F.F. Wu, F.L. Gao, L.T. Huang, X.Y. Liu, P. Lu, B.G. Sun, J.G. Wang, J.H. Wei, T.Y. Zhou USTC/NSRL, Hefei, Anhui, People’s Republic of China
	Funding: Supported by the National Science Foundation of China (Grant No. 11705203, 11575181, 11605202) and the National Key Research and Development Program of China(No. 2016YFA0402000) Beam transverse quadrupole oscillation can be excited in the injection stage if injected beam parameters(twiss parameters or dispersion) are not matched with the parameters in the injection point of the storage ring. In order to measure the beam transverse quadrupole oscillation in the injection stage for the HLS-II storage ring, some axially symmetric stripline BPMs were designed. Transverse quadrupole component for these BPMs was simulated and off-line calibrated. Beam transverse quadrupole oscillation has been measured when beam was injected into the HLS-II electron storage ring. The spectrum of the transverse quadrupole component showed that beam transverse quadrupole oscillation is very obvious in the injection stage and this oscillation isn’t the second harmonic of beam betatron oscillation. The relationship between transverse quadrupole oscillation and beam current was also analyzed and the result shows that the relationship is not linear.
	Poster TUPC12 [0.467 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUPC12
About •	paper received ※ 06 September 2018 paper accepted ※ 12 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEOB02	RadFET Dose Monitor System for SOLEIL	radiation, electron, electronics, vacuum	353
	N. Hubert, F. Dohou, M. El Ajjouri, D. Pédeau SOLEIL, Gif-sur-Yvette, France
	Soleil is currently testing new dose monitors based on RadFET transistors. This new detector at SOLEIL will provide a measurement of the dose received by equipment that are damaged by the radiations in the storage ring, and to anticipate their replacement. This monitor should be very compact to be placed in tiny areas, sensitive to all kind of radiation and low cost to install many of them around the ring. A readout electronic module is being developed in-house, and a first prototype has been build and installed on the machine. Description of the system and first results recorded on the machine are presented.
	Slides WEOB02 [4.250 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEOB02
About •	paper received ※ 05 September 2018 paper accepted ※ 12 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPA02	Recent Progress of Bunch Resolved Beam Diagnostics for BESSY VSR	diagnostics, photon, cavity, beam-diagnostic	379
	J.G. Hwang, T. Atkinson, P. Goslawski, A. Jankowiak, M. Koopmans, T. Mertens, M. Ries, A. Schälicke, G. Schiwietz HZB, Berlin, Germany
	BESSY VSR is an upgrade project of the existing storage ring BESSY II to create long and short photon pulses simultaneously for all beam lines by installing additional superconducting cavities with harmonic frequencies of 1.5 GHz and 1.75 GHz. The storage-ring operation will be influenced by a transient beam-loading effect of all cavities and by the complex filling pattern due to the disparity in the current of long and short bunches. This, in turn, could introduce a variation of beam trajectory, transverse profile, and length for the different bunches. This stimulates the development of bunch-resolved monitors for bunch length, beam size, filling pattern and beam trajectory displacement. In this paper, we show new developments of crucial beam diagnostics including measurements of the bunch-resolved temporal profile with a resolution of less than 1 ps FWHM and bunch-resolved profile with a resolution of less than 10 um rms. The upgrade of the booster beam-diagnostics will be discussed as well.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEPA02
About •	paper received ※ 04 September 2018 paper accepted ※ 13 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPB18	Performance of a Reflective Microscope Objective in an X-ray Pinhole Camera	target, photon, electron, emittance	477
	L. Bobb, G. Rehm DLS, Oxfordshire, United Kingdom
	X-ray pinhole cameras are used to measure the transverse beam profile of the electron beam in the storage ring from which the emittance is calculated. As improvements to the accelerator lattice reduce the beam emittance, e.g. with upgrades to fourth generation synchrotron light sources, likewise the beam size will be reduced such that micron and sub-micron scale resolution is required for beam size measurement. Therefore the spatial resolution of the pinhole camera imaging system must be improved accordingly. Here, the performance of a reflective microscope objective is compared to the high quality refractive lens which is currently in use to image the scintillator screen to the camera. The modulation transfer functions for each system have been assessed and will be discussed.
	Poster WEPB18 [0.751 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEPB18
About •	paper received ※ 04 September 2018 paper accepted ※ 12 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPC15	Machine Learning Applied to Predict Transverse Oscillation at SSRF	diagnostics, SRF, injection, network	512
	B. Gao, J. Chen, Y.B. Leng, Y.M. Zhou SINAP, Shanghai, People’s Republic of China
	A fast beam size diagnostic system has been developed at SSRF (Shanghai Synchrotron Radiation Facility) storage ring for turn-by-turn and bunch-by-bunch beam transverse oscillation study. This system is based on visible synchrotron radiation direct imaging system. Currently, this system already has good experimental results. However, this system still has some limitations, the resolution is subject to the point spread function and the speed of online data processing is limited by the complex algorithm. We present a technique that applied machine learning tools to predict transverse oscillation.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEPC15
About •	paper received ※ 05 September 2018 paper accepted ※ 13 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THOB01	Injection Transient Study Using 6-Dimensional Bunch-by-bunch Diagnostic System at SSRF	SRF, injection, extraction, kicker	542
	Y.M. Zhou, Y.B. Leng, N. Zhang SSRF, Shanghai, People’s Republic of China B. Gao SINAP, Shanghai, People’s Republic of China
	Beam instability often occurs in the accelerator and even causes beam loss. The beam injection transient process provides an important window for the study of beam instability. Measurement of the bunch-by-bunch dynamic parameters of the storage ring is useful for accelerator optimization. A 6-dimensional bunch-by-bunch diagnostic system has been successfully implemented at SSRF. The measurements of transverse position and size and longitudinal phase and length are all completed by the system. Button BPM is used to measure beam position, phase, and length, and the synchrotron radiation light is used to beam size measurement. Signals are sampled simultaneously by a multi-channel acquisition system with the same clock and trigger. Different data processing methods are used to extract the 6-dimensional information, where the delta-over-sum algorithm for beam position extraction, the Gaussian fitting algorithm for beam size extraction, zero-crossing detection algorithm for beam phase extraction and the two-frequency method for bunch length extraction. The system set up and performance will be discussed in more detail in this paper.
	Slides THOB01 [7.413 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-THOB01
About •	paper received ※ 05 September 2018 paper accepted ※ 10 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THOB02	Energy Loss Measurements with Streak Camera at ALBA	injection, simulation, synchrotron, GUI	548
	A.A. Nosych, B. Bravo, U. Iriso ALBA-CELLS Synchrotron, Cerdanyola del Vallès, Spain
	Analyzing streak camera images of the beam injected into a Storage Ring with no RF voltage allows calculating several parameters, like the energy loss per turn and the energy mismatch between injected and stored beams. These measurements are based on the analysis of the centroid drift path of a bunch as it spirals inwards, changing its rotation period. This drift is clear and measurable in single and multi-bunch modes in several horizontal sweep speeds of the streak. With this technique we also measure the momentum compaction factor and observe its change with respect to the insertion devices’ open/closed states. The obtained values are comparable with theoretical expectations, as well as with values measured by other means.
	Slides THOB02 [3.030 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-THOB02
About •	paper received ※ 07 September 2018 paper accepted ※ 14 September 2018 issue date ※ 29 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Other Keywords

Page

MOPB09

Comparison Among Different Tune Measurement Schemes at HLS-II Storage Ring

betatron, detector, pick-up, experiment

93

L.T. Huang, X.Y. Liu, P. Lu, M.X. Qian, B.G. Sun, J.G. Wang, J.H. Wei, F.F. Wu, Y.L. Yang, T.Y. Zhou
USTC/NSRL, Hefei, Anhui, People’s Republic of China

Tune measurement is one of the most significant beam diagnostics at HLS-II storage ring. When measuring tune, higher tune spectral component and lower other compo-nents are expected, so that the tune measurement will be more accurate. To this end, a set of BBQ (Base Band Tune) front-end based on 3D (Direct Diode Detection) technique has previously developed to improve the effec-tive signal content and suppress other components. Em-ploying the BBQ front-end, four different tune measure-ment schemes are designed and related experiments per-formed on the HLS-II storage ring. Experimental results and analysis will be presented later.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPB09

About •

paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPB14

SSRF Beam Operation Stability Evaluation Using Bunch by Bunch Beam Position Method

injection, SRF, operation, damping

104

N. Zhang
SSRF, Shanghai, People’s Republic of China
Y.B. Leng, Y.M. Zhou
SINAP, Shanghai, People’s Republic of China

Funding: Work supported by National Natural Science Foundation of China (No.11575282 No.11375255 No.11305253)
In order to improve the efficiency and quality of light in top-up mode at SSRF, disturbance caused by leakage fields mismatch during injection should be minimized and stable. This could be evaluated by analysis of bunch by bunch residual betatron oscillation data, using this method, instability of tune distribution and damping repeatability could also be calculated. So we could evaluate the beam operation stability by the data analysis and discuss in the paper.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPB14

About •

paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPC02

Identification of Faulty Beam Position Monitor Based Clustering by Fast Search and Find of Density Peaks

SRF, electron, electronics, operation

114

R. Jiang, Y.B. Leng
SSRF, Shanghai, People’s Republic of China
F.Z. Chen, Z.C. Chen, Y.B. Leng
SINAP, Shanghai, People’s Republic of China

The accuracy and stability of beam position moni-tors(BPMs) are important for all kinds of measurement systems and feedback systems in particle accelerator field. A proper method detecting faulty beam position monitor or monitoring their stability could optimize accel-erator operating conditions. With development in ma-chine learning methods, a series of powerful analysis approaches make it possible for detecting beam position monitor’s stability. Here, this paper proposed a clustering analysis approach to detect the defective BPMs. The method is based on the idea that cluster centres are char-acterized by a higher density than their neighbours and by a relatively large distance from points with higher densi-ties. The results showed that clustering by fast search and find of density peaks could classify beam data into dif-ferent clusters on the basis of their similarity. And that, aberrant data points could be detected by decision graph. So the algorithm is appropriate for BPM detecting and it could be a significant supplement for data analysis in accelerator physics.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPC02

About •

paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPC03

Precise Measurement of Small Currents at the MLS

electron, radiation, experiment, synchrotron

118

Y. Petenev, J. Feikes, J. Li, A.N. Matveenko, Y. Tamashevich
HZB, Berlin, Germany
R. Klein, J. Lubeck, R. Thornagel
PTB, Berlin, Germany

The Physikalisch-Technische Bundesanstalt (PTB), the National Metrology Institute of Germany, utilizes an electron storage ring - the Metrology Light Source (MLS), located in Berlin, as a radiation source standard in the VIS, UV and VUV spectral range. In order to be able to calculate the absolute intensity of the radiation, the electron beam current has to be measured with low uncertainty. In this paper we focus on the measurement of the beam current in a range of several nA to 1 pA (one electron) by means of Si photodiodes, detecting synchrotron radiation from the beam. Electrons are gradually scraped out of the ring and the diode signal is analyzed afterwards. The exact number of stored electrons then can be derived from the signal. The measurement is carried out automatically with an in-house developed software.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPC03

About •

paper received ※ 04 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPC08

Beam Intensity Monitoring with nA Resolution - the Cryogenic Current Comparator (CCC)

cryogenics, antiproton, proton, shielding

130

D.M. Haider, P. Forck, F. Kurian, M. Schwickert, T. Sieber, T. Stöhlker
GSI, Darmstadt, Germany
H. De Gersem, N. Marsic
TEMF, TU Darmstadt, Darmstadt, Germany
M.F. Fernandes, J. Tan
CERN, Geneva, Switzerland
J. Golm, F. Schmidl, P. Seidel
FSU Jena, Jena, Germany
J. Golm, T. Stöhlker, V. Tympel
HIJ, Jena, Germany
M. Schmelz, R. Stolz, V. Zakosarenko
IPHT, Jena, Germany
T. Stöhlker
IOQ, Jena, Germany
V. Zakosarenko
Supracon AG, Jena, Germany

Funding: Work supported by AVA - Accelerators Validating Antimatter the EU H2020 Marie-Curie Action No. 721559 and by the BMBF under contract No. 05P15SJRBA.
The storage of low current beams as well as the long extraction times from the synchrotrons at FAIR require non-destructive beam intensity monitoring with a current resolution of nanoampere. To fulfill this requirement, the concept of the Cryogenic Current Comparator (CCC), based on the low temperature SQUID, is used to obtain an extremely sensitive beam current transformer. During the last years, CCCs have been installed to do measurements of the spill structure in the extraction line of GSI SIS18 and for current monitoring in the CERN Antiproton Decelerator. From these experiences lessons can be learned to facilitate further developments. The goal of the ongoing research is to improve the robustness of the CCC towards external influences, such as vibrations, stray fields and He-pressure variations, as well as to develop a cost-efficient concept for the superconducting shield and the cryostat.

Poster MOPC08 [1.441 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPC08

About •

paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPC16

The Development and Applications of Digital BPM Signal Processor on SSRF

SRF, brilliance, controls, FEL

147

L.W. Lai, F.Z. Chen, Y.B. Leng, Y.B. Yan, N. Zhang, W.M. Zhou
SSRF, Shanghai, People’s Republic of China

The development of Digital BPM Signal Processors (DBPM) for SSRF started from 2008. The first prototype for SSRF storage ring was completed in 2012, with turn-by-turn resolution better than 1μm. From 2016 to 2017, SSRF successively constructed two FEL facilities in China, DCLS and SXFEL test facilities. The second ver-sion DBPM was developed and used in large scale during this period to meet the requirements of signal processing for stripline BPMs and cavity BPMs. After that, we turned to the development of DBPM for SSRF storage ring based on the second version hardware, including FPGA firmware, EPICS IOC, EDM control panel. The development was completed and tests were carried out in early 2018. Test results showed that the position data is accurate and can monitor beam movement correctly, and online turn-by-turn position data resolution reaches 0.46μm. This paper will introduce the design of DBPM for the SSRF storage ring and the tests carried out to verify the data accuracy and evaluate the system performance.

Poster MOPC16 [1.372 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-MOPC16

About •

paper received ※ 04 September 2018 paper accepted ※ 13 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUOB03

Demonstration of a Newly Developed Pulse-by-pulse X-Ray Beam Position Monitor in SPring-8

detector, radiation, operation, ISOL

182

H. Aoyagi, Y. Furukawa, S. Takahashi, A. Watanabe
JASRI/SPring-8, Hyogo, Japan

Funding: This work was partly supported by Japan Society for the Promotion of Science through a Grant-in-Aid for Scientific Research (c), No. 20416374 and No. 18K11943.
A newly designed pulse-by-pulse X-ray beam position monitor (XBPM), which is photoemission type, has been demonstrated successfully in the SPring-8 synchrotron radiation beamline. Conventional XBPMs work in the direct-current (DC) mode, because it is difficult to measure a beam position in the pulse mode under the sever heat load condition. The key point of the design is aiming at improving heat-resistance property without degradation of high frequency property [1]. This monitor is equipped with microstripline structure for signal transmission line to achieve pulse-by-pulse beam position signal. A photocathode is titanium electrode that is sputtered on a diamond heat sink to achieve high heat resistance. We have manufactured the prototype, and demonstrated feasibility at the SPring-8 bending magnet beamline. As a result, we observed a unipolar single pulse with the pulse length of less than 1 ns FWHM and confirmed that it has pulse-by-pules position sensitivity [2]. Furthermore, this monitor can be also used in the direct-current mode with good stability and good resolution. The operational experience will be also presented.
[1] http://accelconf.web.cern.ch/AccelConf/medsi2016/papers/wepe10.pdf
[2] http://www.pasj.jp/web_publish/pasj2017/proceedings/PDF/THOM/THOM06.pdf

Slides TUOB03 [2.380 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUOB03

About •

paper received ※ 31 August 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUOC04

Development of Beam Position Monitor for the SPring-8 Upgrade

electron, electronics, radiation, brilliance

204

H. Maesaka
RIKEN SPring-8 Center, Innovative Light Sources Division, Hyogo, Japan
H. Dewa, T. Fujita, M. Masaki, S. Takano
JASRI, Hyogo, Japan

We are developing a new electron beam position monitor (BPM) system for the low-emittance upgrade of SPring-8. The requirements for the BPM system are: (1) a single-pass resolution of 100 µm rms for a 100 pC bunch and an electric center accuracy of 100 µm rms for the initial beam commissioning to achieve the first turn, (2) a closed-orbit distortion (COD) resolution better than 0.1 µm rms for a 100 mA stored beam and a position stability of less than 5 µm for the ultimate stability of a photon beam axis. We have completed prototypes of a precise button electrode and a BPM block to obtain high-intensity signals and sufficient mechanical accuracy while suppressing high-Q trapped modes leading to impedance and heating issues. The development of readout electronics based on the MTCA.4 standard and the evaluation of radiation-hard coaxial cables have also been conducted. The prototype BPM head was installed in the present SPring-8 storage ring for performance verification with an actual electron beam. We confirmed sufficient signal intensity, electric center accuracy, position stability, etc. by the beam test. The new BPM system is almost ready for the SPring-8 upgrade.

Slides TUOC04 [2.126 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUOC04

About •

paper received ※ 06 September 2018 paper accepted ※ 12 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPA03

Test of New Beam Loss Monitors for SOLEIL

detector, controls, shielding, electron

215

N. Hubert, M. El Ajjouri, D. Pédeau
SOLEIL, Gif-sur-Yvette, France

Soleil is currently testing new beam loss monitors to replace its pin-diode based existing system. The new detectors are made of plastic scintillators associated with photomultiplier and connected to Libera BLM dedicated electronics. This new detector should provide both fast (turn by turn) and slow (averaged) loss measurements, post mortem capabilities and should be less sensitive to the beam directivity compared to the pin-diodes. Different methods for a relative calibration of the modules are under investigation, either using a diode (LED) or a cesium radioactive source. Calibration results and first measurements with beam are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUPA03

About •

paper received ※ 05 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPB04

Development of a New Button Beam-position Monitor for BESSY VSR

impedance, vacuum, resonance, operation

265

J.G. Hwang, V. Dürr, M. Ries, A. Schälicke, G. Schiwietz, D. Wolk
HZB, Berlin, Germany

An extreme operation mode such as the BESSY-VSR conditions stimulates the development of a high accuracy bunch-by-bunch beam-position monitor (BPM) system which is compatible with the bunch-selective operation for the orbit feedback system. Such a system will also greatly benefit to accelerator R&D such as transverse resonance island buckets (TRIBs). Compensation of the long-range ringing signal produced by the combined effect of impedance mismatching inside the button and trapped TE-modes in the aluminum-oxide insulator (Al2O3) material is required essentially to improve the resolution. This is important since the ringing causes a misreading of the beam position and current of following bunches. We show the design study of a new button-type BPM to mitigate the influence of the ringing signal as well as to reduce wake losses by improving the impedance matching in the button and by replacing the insulator material.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUPB04

About •

paper received ※ 04 September 2018 paper accepted ※ 11 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPC01

Australian Synchrotron BPM Electronics Upgrade

electron, brilliance, coupling, synchrotron

297

Y.E. Tan, R.B. Hogan
AS - ANSTO, Clayton, Australia

The storage ring at the Australian Synchrotron (AS) was originally equipped with 98 Libera Electrons. In late 2017 all 98 of the BPM electronics has been upgraded to Libera Brilliance⁺ and the old Libera Electrons have been moved to the injection system. The transition process and results from commissioning the new system will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUPC01

About •

paper received ※ 05 September 2018 paper accepted ※ 13 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPC12

Beam Transverse Quadrupole Oscillation Measurement in the Injection Stage for the HLS-II Storage Ring

quadrupole, injection, betatron, electron

325

F.F. Wu, F.L. Gao, L.T. Huang, X.Y. Liu, P. Lu, B.G. Sun, J.G. Wang, J.H. Wei, T.Y. Zhou
USTC/NSRL, Hefei, Anhui, People’s Republic of China

Funding: Supported by the National Science Foundation of China (Grant No. 11705203, 11575181, 11605202) and the National Key Research and Development Program of China(No. 2016YFA0402000)
Beam transverse quadrupole oscillation can be excited in the injection stage if injected beam parameters(twiss parameters or dispersion) are not matched with the parameters in the injection point of the storage ring. In order to measure the beam transverse quadrupole oscillation in the injection stage for the HLS-II storage ring, some axially symmetric stripline BPMs were designed. Transverse quadrupole component for these BPMs was simulated and off-line calibrated. Beam transverse quadrupole oscillation has been measured when beam was injected into the HLS-II electron storage ring. The spectrum of the transverse quadrupole component showed that beam transverse quadrupole oscillation is very obvious in the injection stage and this oscillation isn’t the second harmonic of beam betatron oscillation. The relationship between transverse quadrupole oscillation and beam current was also analyzed and the result shows that the relationship is not linear.

Poster TUPC12 [0.467 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-TUPC12

About •

paper received ※ 06 September 2018 paper accepted ※ 12 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEOB02

RadFET Dose Monitor System for SOLEIL

radiation, electron, electronics, vacuum

353

N. Hubert, F. Dohou, M. El Ajjouri, D. Pédeau
SOLEIL, Gif-sur-Yvette, France

Soleil is currently testing new dose monitors based on RadFET transistors. This new detector at SOLEIL will provide a measurement of the dose received by equipment that are damaged by the radiations in the storage ring, and to anticipate their replacement. This monitor should be very compact to be placed in tiny areas, sensitive to all kind of radiation and low cost to install many of them around the ring. A readout electronic module is being developed in-house, and a first prototype has been build and installed on the machine. Description of the system and first results recorded on the machine are presented.

Slides WEOB02 [4.250 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEOB02

About •

paper received ※ 05 September 2018 paper accepted ※ 12 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPA02

Recent Progress of Bunch Resolved Beam Diagnostics for BESSY VSR

diagnostics, photon, cavity, beam-diagnostic

379

J.G. Hwang, T. Atkinson, P. Goslawski, A. Jankowiak, M. Koopmans, T. Mertens, M. Ries, A. Schälicke, G. Schiwietz
HZB, Berlin, Germany

BESSY VSR is an upgrade project of the existing storage ring BESSY II to create long and short photon pulses simultaneously for all beam lines by installing additional superconducting cavities with harmonic frequencies of 1.5 GHz and 1.75 GHz. The storage-ring operation will be influenced by a transient beam-loading effect of all cavities and by the complex filling pattern due to the disparity in the current of long and short bunches. This, in turn, could introduce a variation of beam trajectory, transverse profile, and length for the different bunches. This stimulates the development of bunch-resolved monitors for bunch length, beam size, filling pattern and beam trajectory displacement. In this paper, we show new developments of crucial beam diagnostics including measurements of the bunch-resolved temporal profile with a resolution of less than 1 ps FWHM and bunch-resolved profile with a resolution of less than 10 um rms. The upgrade of the booster beam-diagnostics will be discussed as well.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEPA02

About •

paper received ※ 04 September 2018 paper accepted ※ 13 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPB18

Performance of a Reflective Microscope Objective in an X-ray Pinhole Camera

target, photon, electron, emittance

477

L. Bobb, G. Rehm
DLS, Oxfordshire, United Kingdom

X-ray pinhole cameras are used to measure the transverse beam profile of the electron beam in the storage ring from which the emittance is calculated. As improvements to the accelerator lattice reduce the beam emittance, e.g. with upgrades to fourth generation synchrotron light sources, likewise the beam size will be reduced such that micron and sub-micron scale resolution is required for beam size measurement. Therefore the spatial resolution of the pinhole camera imaging system must be improved accordingly. Here, the performance of a reflective microscope objective is compared to the high quality refractive lens which is currently in use to image the scintillator screen to the camera. The modulation transfer functions for each system have been assessed and will be discussed.

Poster WEPB18 [0.751 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEPB18

About •

paper received ※ 04 September 2018 paper accepted ※ 12 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPC15

Machine Learning Applied to Predict Transverse Oscillation at SSRF

diagnostics, SRF, injection, network

512

B. Gao, J. Chen, Y.B. Leng, Y.M. Zhou
SINAP, Shanghai, People’s Republic of China

A fast beam size diagnostic system has been developed at SSRF (Shanghai Synchrotron Radiation Facility) storage ring for turn-by-turn and bunch-by-bunch beam transverse oscillation study. This system is based on visible synchrotron radiation direct imaging system. Currently, this system already has good experimental results. However, this system still has some limitations, the resolution is subject to the point spread function and the speed of online data processing is limited by the complex algorithm. We present a technique that applied machine learning tools to predict transverse oscillation.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-WEPC15

About •

paper received ※ 05 September 2018 paper accepted ※ 13 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THOB01

Injection Transient Study Using 6-Dimensional Bunch-by-bunch Diagnostic System at SSRF

SRF, injection, extraction, kicker

542

Y.M. Zhou, Y.B. Leng, N. Zhang
SSRF, Shanghai, People’s Republic of China
B. Gao
SINAP, Shanghai, People’s Republic of China

Beam instability often occurs in the accelerator and even causes beam loss. The beam injection transient process provides an important window for the study of beam instability. Measurement of the bunch-by-bunch dynamic parameters of the storage ring is useful for accelerator optimization. A 6-dimensional bunch-by-bunch diagnostic system has been successfully implemented at SSRF. The measurements of transverse position and size and longitudinal phase and length are all completed by the system. Button BPM is used to measure beam position, phase, and length, and the synchrotron radiation light is used to beam size measurement. Signals are sampled simultaneously by a multi-channel acquisition system with the same clock and trigger. Different data processing methods are used to extract the 6-dimensional information, where the delta-over-sum algorithm for beam position extraction, the Gaussian fitting algorithm for beam size extraction, zero-crossing detection algorithm for beam phase extraction and the two-frequency method for bunch length extraction. The system set up and performance will be discussed in more detail in this paper.

Slides THOB01 [7.413 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-THOB01

About •

paper received ※ 05 September 2018 paper accepted ※ 10 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THOB02

Energy Loss Measurements with Streak Camera at ALBA

injection, simulation, synchrotron, GUI

548

A.A. Nosych, B. Bravo, U. Iriso
ALBA-CELLS Synchrotron, Cerdanyola del Vallès, Spain

Analyzing streak camera images of the beam injected into a Storage Ring with no RF voltage allows calculating several parameters, like the energy loss per turn and the energy mismatch between injected and stored beams. These measurements are based on the analysis of the centroid drift path of a bunch as it spirals inwards, changing its rotation period. This drift is clear and measurable in single and multi-bunch modes in several horizontal sweep speeds of the streak. With this technique we also measure the momentum compaction factor and observe its change with respect to the insertion devices’ open/closed states. The obtained values are comparable with theoretical expectations, as well as with values measured by other means.

Slides THOB02 [3.030 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2018-THOB02

About •

paper received ※ 07 September 2018 paper accepted ※ 14 September 2018 issue date ※ 29 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)