Keyword: optics
Paper Title Other Keywords Page
TUPP010 A Fast Wire Scanner System for the European XFEL FEL, timing, operation, detector 304
 
  • T. Lensch, B. Beutner, T. Wamsat
    DESY, Hamburg, Germany
 
  The European-XFEL is an X-ray Free Electron Laser facility located in Hamburg (Germany). The 17.5 GeV superconducting accelerator will provide photons simultaneously to several user stations. Currently 14 Wire Scanner stations are used to image transverse beam profiles in the high energy sections. These scanners provide a slow scan mode for beam halo studies and beam optics matching. When operating with long bunch trains (>100 bunches) fast scans will be used to measure beam sizes in an almost non-destructive manner. This paper briefly describes the wire scanner setup and focusses on the fast scan concept and first measurements.  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2019-TUPP010  
About • paper received ※ 04 September 2019       paper accepted ※ 10 September 2019       issue date ※ 10 November 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUPP017 Thermal Performance of Diamond SR Extraction Mirrors for SuperKEKB extraction, MMI, radiation, electron 332
 
  • J.W. Flanagan, M. Arinaga, H. Fukuma, H. Ikeda, G. Mitsuka, Y. Suetsugu
    KEK, Ibaraki, Japan
  • E. Mulyani
    BATAN, Yogyakarta, Indonesia
  • E. Mulyani
    Sokendai, Ibaraki, Japan
 
  The SuperKEKB accelerator is a high-current, low-emittance upgrade to the KEKB double ring collider. The beryllium extraction mirrors used for the synchrotron radiation (SR) monitors at KEKB suffered from heat distortion due to incident SR, leading to systematic changes in magnification with beam current, and necessitating continuous monitoring and compensation of such distortions in order to correctly measure the beam sizes.* To minimize such mirror distortions, quasi-monocrystalline CVD diamond mirrors have been designed and installed at SuperKEKB.** Diamond has a very high heat conductance and a low thermal expansion coefficient. With such mirrors it is hoped to reduce the beam current-dependent magnification to the level of a few percent at SuperKEKB. Preliminary measurements of mirror distortion during SuperKEKB commissioning show very promising results with regard to thermal performance, though full beam currents have not yet been stored in the SuperKEKB rings. Measurements of the thermal deformation of the diamond mirrors will be presented in this paper, along with a description of the design of the mirrors and their mounts, and issues encountered during commissioning.
*M. Arinaga et al., NIM, A499, p. 100 (2003).
**J.W. Flanagan et al., "Diamond mirrors for the SuperKEKB synchrotron radiation monitors," Proc. IBIC2012, Tsukuba, Japan p. 515 (2012).
 
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2019-TUPP017  
About • paper received ※ 09 September 2019       paper accepted ※ 10 September 2019       issue date ※ 10 November 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUPP042 Turn-by-Turn Synchrotron Radiation Transverse Profile Monitor for IOTA experiment, radiation, electron, lattice 432
 
  • N. Kuklev, Y.K. Kim
    University of Chicago, Chicago, Illinois, USA
 
  Funding: Work supported by National Science Foundation award PHY-1549132, the Center for Bright Beams. Fermi Research Alliance operates Fermilab under Contract DE-AC02-07CH11359 with the US Dept. of Energy.
The Integrable Optics Test Accelerator is a research electron and proton storage ring recently commissioned at Fermilab. A key part of its beam diagnostics suite are synchrotron radiation monitors, used for measuring transverse beam profile, position, and intensity. So far, this system has used only visible light cameras, which are optimal for orbit measurements but do not provide turn-by-turn temporal resolution needed for beam dynamics analysis. Current electrostatic BPM system, while capable of turn-by-turn acquisition, will be pushed to its limits of accuracy and linearity by the requirements of planned nonlinear integrable optics experiments, and furthermore does not provide transverse profile data. To address these drawbacks, we present in this paper the design of a turn-by-turn BPM system based on a multi-anode photomultiplier detector. Extensive simulations are shown, combining both particle and optics tracking. A potential hardware and readout architecture is described. Statistical and systematic errors are explored. We conclude by outlining the prototype testing plans for run 2 in the fall of 2019, and other future work.
 
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2019-TUPP042  
About • paper received ※ 11 September 2019       paper accepted ※ 12 September 2019       issue date ※ 10 November 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
WEPP005 BPM Resolution Studies at PETRA III brilliance, electron, electronics, pick-up 517
 
  • G. Kube, J. Neugebauer, F. Schmidt-Föhre
    DESY, Hamburg, Germany
 
  In order to measure the noise level of a BPM system from beam generated orbit data, the correlated beam jitter has to be removed from the position signals. There exist different ways to extract the BPM noise, as the "three-BPM" correlation method or the model-independent principal components analysis (PCA). Both methods will shortly be reviewed. Based on a PCA, the resolution of the PETRA III Libera Brilliance based BPM system was measured. The results will be presented together with first measurements in view of an updated BPM system for the future PETRA IV project at DESY.  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2019-WEPP005  
About • paper received ※ 02 September 2019       paper accepted ※ 10 September 2019       issue date ※ 10 November 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
WEPP018 THz Generation by Optical Rectification for a Novel Shot to Shot Synchronization System Between Electron Bunches and Femtosecond Laser Pulses in a Plasma Wakefield Accelerator laser, plasma, electron, wakefield 555
 
  • S. Mattiello, A. Penirschke
    THM, Friedberg, Germany
  • H. Schlarb
    DESY, Hamburg, Germany
 
  Funding: The work of S. Mattiello is supported by the German Federal Ministry of Education and Research (BMBF) within the Project ¿ MAKE-PWA.
We investigate the influence of the optical properties and of the theoretical description of the THz generation on the conversion efficiency of the generation of short THz pulses. The application is a feedback-system for SINBAD with a time resolution of less than 1 fs for the synchronization of the electron bunch and of the plasma wake field in a laser driven plasma particle accelerator*. Here stable THz pulses are generated by optical rectification of a fraction of the plasma generating high energy laser pulses in a nonlinear lithium niobate crystal. Then the generated THz pulses will energy modulate the electron bunches shot to shot before the plasma to achieve the required time resolution. In this contribution we compare different approximations for the modeling of the generation dynamics using second order or first order equations as well as considering pump depletion effects. Additionally, the dependence of the efficiency of the THz generation on the choice of the dielectric function has been investigated.
*The feedback system will be tested at the Accelerator R&D facility SINBAD (Short Innovative Bunches and Accelerators at DESY).
 
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2019-WEPP018  
About • paper received ※ 04 September 2019       paper accepted ※ 09 September 2019       issue date ※ 10 November 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
WEPP034 Optics-Measurement-Based BPM Calibration factory, collider, dipole, injection 610
 
  • A. García-Tabarés Valdivieso, R. Tomás
    CERN, Geneva, Switzerland
 
  Beam position monitors (BPMs) are key elements in accelerator operation, providing essential information about different beam parameters that are directly related to the accelerator performance. In order to obtain an accurate conversion from an induced voltage to the center of charge position, the BPMs have to be calibrated prior to its installation in the accelerator. This calibration procedure can only be performed when the accelerator is in a period of non-activity and does not completely reproduce the exact conditions that occur during the machine operation. Discrepancies observed during the optics measurements at the Large Hadron Collider and the Proton Synchrotron Booster show that the impact of the BPM calibration factors on the optics functions was greater than expected from the design values and tolerances. Measurement of the optics functions allows obtaining extra information on BPM calibration together with its associated uncertainty and resolution. The optics measurement based calibration allows further developing new techniques for computing optics functions that are biased by a possible miss-calibration such as beta function, dispersion function and beam action.  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IBIC2019-WEPP034  
About • paper received ※ 04 September 2019       paper accepted ※ 10 September 2019       issue date ※ 10 November 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)