| Paper | Title | Other Keywords | Page |
|---|---|---|---|
| MOPGW092 | Design Status of DESY IV – Booster Upgrade for PETRA IV | booster, injection, emittance, linac | 331 |
|
|||
| In PETRA IV project the on-axis injection scheme is preferred since there is no sufficient dynamic aperture for off-axis injection in ultra low emittance storage rings. The challenge is to prepare the injected bunches with the smaller emittance and larger intensity. The current injector complex including the accumulator and booster does not fulfill the requirements and thus will need refurbishments. The injector upgrade option chosen will be composed of an upgraded electron gun, a higher energy LINAC, and the new booster synchrotron DESY IV which has smaller emittance. DESY IV will be located in the existing tunnel of the current booster DESY II. The design of the lattice and some simulation results are addressed in this article. | |||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-MOPGW092 | ||
| About • | paper received ※ 18 April 2019 paper accepted ※ 20 May 2019 issue date ※ 21 June 2019 | ||
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
| MOPGW128 | Simulation and Analysis of Wake Fields and Trapped RF Modes in Insertion Device Vacuum Chambers at the Canadian Light Source | vacuum, simulation, undulator, insertion-device | 414 |
|
|||
|
Funding: CFI, NSERC, NRC, CIHR, the Province of Saskatchewan, WD, WESTGRID, Compute Canada, and the University of Saskatchewan The Canadian Light Source (CLS) synchrotron operates with four in-vacuum insertion devices, three in-vacuum undulators, and one in-vacuum wiggler. Presently, each of the devices occupies half of a straight section. The wiggler is unique in our ring as it is both in-vacuum and shares a straight section with an in-vacuum undulator. We have observed gap dependent beam instabilities in the undulator located in the straight section. In order to better understand the problem, the cause of the instabilities was investigated using 3D electromagnetic modelling. First, the ’trapped’ RF modes (natural resonances) for this undulator chamber, their Q value, and their peak frequencies were analysed using Eigenmode simulation. Secondly, beam excitation of the Eigenmodes was simulated with the Wakefield solver. Herein we present the results of this electromagnetic modelling. |
|||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-MOPGW128 | ||
| About • | paper received ※ 14 May 2019 paper accepted ※ 23 May 2019 issue date ※ 21 June 2019 | ||
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
| MOPMP001 | Optic Corrections for FCC-hh | quadrupole, injection, dipole, coupling | 417 |
|
|||
| The FCC-hh (Future Hadron-Hadron Circular Collider) is one of the options considered for the next generation accelerator in high-energy physics as recommended by the European Strategy Group. The evaluation of the various magnets mechanical error and field error tolerances in the arc sections of FCC-hh, as well as an estimation of the required correctors strengths, are important aspects of the collider design. In this study the mechanical tolerances, dipole and quadrupole field error tolerances for the arc sections of FCC-hh are evaluated. The consolidated correction schemes of the linear coupling (with skew quadrupoles) and of the beam tunes (with normal quadrupoles) are presented. The integration of the different ring insertions (interaction region, collimation, injection, etc) is also discussed. | |||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-MOPMP001 | ||
| About • | paper received ※ 14 May 2019 paper accepted ※ 23 May 2019 issue date ※ 21 June 2019 | ||
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
| MOPMP004 | Consolidated Lattice of the Collider FCC-hh | dipole, quadrupole, injection, optics | 428 |
|
|||
|
Funding: The European Circular Energy-Frontier Collider Study (EuroCirCol) project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant No 654305. The FCC-hh (Future Hadron-Hadron Circular Collider) is one of the options considered for the next generation accelerator in high-energy physics as recommended by the European Strategy Group. The latest changes brought to the lattice of the FCC-hh collider are commented: impact of the new intra-beam distance, efforts to increase the beam stay clear in the dispersion suppressors, tuning procedures, and updates on the insertions. |
|||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-MOPMP004 | ||
| About • | paper received ※ 14 May 2019 paper accepted ※ 20 May 2019 issue date ※ 21 June 2019 | ||
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
| MOPMP020 | Smooth and Beta-Beating-Free Optics Transitions for HL-LHC | optics, injection, quadrupole, operation | 472 |
|
|||
| In the CERN LHC, optics transitions are mainly required to control the beam size at the four experimental interaction points. The current method, based on linearly-interpolated optics functions over a small set of matched optics and parabolic time-domain segments, introduces non-zero beta-beating and it is not optimal in time. This contribution presents an alternative approach, based on continuously-matched optics solutions distributed in time domain by using a realistic model of the superconducting circuits, which optimises the overall process duration. This method requires a change in the paradigm used in the control system and it is proposed for the future High Luminosity LHC (HL-LHC) runs. | |||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-MOPMP020 | ||
| About • | paper received ※ 18 April 2019 paper accepted ※ 17 May 2019 issue date ※ 21 June 2019 | ||
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
| WEPGW071 | Evaluation of a New 500 MHz Digitizer at Elettra and Fermi | pick-up, interface, storage-ring, EPICS | 2635 |
|
|||
| A new digitizer was evaluated in ELETTRA storage ring and FERMI linear accelerator. The A/D conversion is done with 14-bits at 500 MS/s. The sampling clock is hard-locked to the Master Oscillator and has a jitter of a maximum 10 ps. The AC coupled version has an analog bandwidth up to 2 GHz and was used to measure the fill pattern. The bunch flat-top is very narrow (10-15 ps). To reach better stability, various external filtering components were used. Bunch-by-bunch beam position was calculated offline and compared to a standard BPM electronics. The DC coupled version was used to sample pulses from the fast current transformer at FERMI. A software interface can configure data acquisition length and fill buffer segments with pre-defined number of triggers. Native TANGO and EPICS interfaces allow for fast integration with CSS and other display tools. | |||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-WEPGW071 | ||
| About • | paper received ※ 13 May 2019 paper accepted ※ 21 May 2019 issue date ※ 21 June 2019 | ||
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
| WEPGW101 | A New Orbit Feedforward Table Generation Method for Insertion Devices | storage-ring, insertion-device, sextupole, ISOL | 2724 |
|
|||
|
Funding: The study is supported by U.S. DOE under Contract No. DE-SC0012704. A new method of orbit feedforward (FF) table generation for insertion devices (IDs) is proposed. The main purpose of the orbit FF table is to suppress orbit disturbance around a storage ring, caused by the gap/phase motion of an ID. A conventional procedure is to measure a closed orbit at a reference ID gap/phase state, and another one at a different state, with all types of orbit feedback (FB) systems disabled. Based on the difference orbit, the correction currents for the local ID correctors are estimated to cancel the global orbit distortion. The new method instead utilizes the orbit deviation at the beam position monitors within an ID straight section (ID BPMs) with respect to a dynamically changing orbit that is defined by the orbit at two BPMs bounding the ID straight. Correction currents are determined such that this orbit deviation at the ID BPMs is minimized. Being impervious to transverse kicks external to this bounded region, this measurement can be performed with a global orbit FB system turned on, which could allow parallel table generation for multiple IDs. |
|||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-WEPGW101 | ||
| About • | paper received ※ 17 May 2019 paper accepted ※ 18 May 2019 issue date ※ 21 June 2019 | ||
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
| WEPRB060 | HOM Damped Normal Conducting 1.5 GHz Cavity Design Evolution for the 3rd Harmonic System of the ALBA Storage Ring | cavity, GUI, HOM, simulation | 2948 |
|
|||
| In a collaboration framework with CERN, ALBA has designed a normal conducting active 1.5 GHz cavity which could serve as main RF system for the Damping Ring of CLIC and as an active third harmonic cavity for the ALBA Storage Ring. The third harmonic cavity at ALBA will be used to increase the bunch length in order to improve the beam lifetime and increase the beam stability thresholds. The main advantage of an active third harmonic cavity is that optimum conditions can be reached for any beam current. This paper presents the evolution of the preliminary design of this cavity and its trans-dampers: high order modes coaxial dampers with waveguide transitions to N, which allows extracting the power of the high order modes induced by the beam outside of the cavity and to dissipate it using standard loads. This approach has two main advantages: no ferrites brazing is needed and they provide a diagnostic to analyze the beam dynamics. The new features of the design, together with electromagnetic simulations, mechanical and thermal stress analysis will be presented in this paper as well as the first stages of the prototype production status. | |||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-WEPRB060 | ||
| About • | paper received ※ 15 May 2019 paper accepted ※ 23 May 2019 issue date ※ 21 June 2019 | ||
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||