IPAC2011 - List of Authors (Rumolo, G.)

Paper

Title

Page

Experimental Studies with Low Transition Energy Optics in the SPS

613

H. Bartosik, T. Argyropoulos, T. Bohl, S. Cettour Cave, K. Cornelis, J. Esteban Muller, Y. Papaphilippou, G. Rumolo, B. Salvant, E.N. Shaposhnikova, J. Wenninger
CERN, Geneva, Switzerland

The optics of the SPS can be tuned to lower transition energy such that the slippage factor at injection is raised by a factor of almost 3. From theory, an increase of the intensity thresholds for transverse mode coupling, longitudinal coupled bunch and longitudinal instabilities due to the loss of Landau damping can be expected. In this paper, experimental studies in the SPS with single bunches of protons with intensities of up to 3.5·10¹¹ p/b on the flat bottom and at 450 GeV/c are presented. Longitudinal instabilities were studied with LHC-type beams with 50~ns spacing and injected intensities up to 1.8·10¹¹ p/b. The measurements address the increase of intensity thresholds and the achievable transverse emittances in the new low gamma transition optics with respect to the nominal SPS optics. The obtained results are compared with numerical simulations.

MOPS011

Impact of Low Transition Energy Optics to the Electron Cloud Instability of LHC Beams in the SPS

616

H. Bartosik, E. Benedetto, K.S.B. Li, Y. Papaphilippou, G. Rumolo
CERN, Geneva, Switzerland

One of the main limitations for high intensity multi-bunch LHC proton beams in the SPS is imposed by electron cloud instabilities. A new optics of the SPS with lower transition energy was implemented and successfully tested in machine studies. The significant increase of the slippage factor that it provides at injection energy results in the expected increase of the single bunch instability thresholds. In this paper, the impact of this new optics on the electron cloud instability threshold is estimated by using numerical simulations, taking into account the change of the optics functions and the faster synchrotron motion due to the reduced transition energy.

MOPS013

Transverse Low Frequency Broad-band Impedance Measurements in the CERN PS

622

S. Aumon
EPFL, Lausanne, Switzerland
P. Freyermuth, S.S. Gilardoni, O. Hans, E. Métral, G. Rumolo
CERN, Geneva, Switzerland

The base-line scenario for the High-Luminosity LHC upgrade foresees an intensity increase delivered by the injectors. With its 53 years, the CERN PS would have to operate beyond the limit of its performances to match the future requirements. Beam instabilities driven by transverse impedance are an important issue for the operation of high intensity beams as for the high-brightness LHC beams. Measurements of transverse tune dependence with beam intensity were performed at injection kinetic energy 1.4~GeV and at LHC beam extraction momentum 26~GeV/c. This allows deducing the low frequency inductive broad-band impedance of the machine. Then an estimation of the real part of the impedance is made by the rise time measurement of a fast transverse instability believed to be a TMCI type. Those are the first step towards a global machine impedance characterization in order to push forward the performances of the accelerator.

MOPS056

An Analytical Formula of the Electron Cloud Linear Map Coefficient in a Strong Dipole

733

T. Demma
INFN/LNF, Frascati (Roma), Italy
S. Petracca, A. Stabile
U. Sannio, Benevento, Italy
G. Rumolo
CERN, Geneva, Switzerland

Electron cloud effects have been indentified as one of the most serious bottleneck for reaching design performances in presently running and proposed future storage rings. The analysis of these effects is usually performed with very time consuming simulation codes. An alternative analytic approach, based on a cubic map model for the bunch-to-bunch evolution of the electron cloud density, could be useful to determine regions in parameters space compatible with safe machine operations. In this communication we derive a simple approximate formula relating the quadratic coefficient in the electron cloud density map to the parameters relevant for the electron cloud evolution in a strong vertical magnetic field. Results are compared with simulations with particular reference to the LHC dipoles.

MOPS068

Localization of Transverse Impedance Sources in the SPS using HEADTAIL Macroparticle Simulations

757

N. Biancacci, G. Arduini, E. Métral, D. Quatraro, G. Rumolo, B. Salvant, R. Tomás
CERN, Geneva, Switzerland
N. Biancacci, M. Migliorati, L. Palumbo
Rome University La Sapienza, Roma, Italy
R. Calaga
BNL, Upton, Long Island, New York, USA

In particle accelerators, beam coupling impedance is one of the main contributors to instability phenomena that lead to particle losses and beam quality deterioration. For this reason these machines are continuously monitored and the global and local amount of impedance needs to be evaluated. In this work we present our studies on the local transverse impedance detection algorithm. The main assumptions behind the algorithm are described in order to understand limits in reconstructing the impedance location. The phase advance response matrix is analyzed in particular for the SPS lattice, studying the different response from 90,180,270 degrees phase advance sections. The thin lenses scheme is also implemented and new analytical formulas for phase advance beating were derived. This avails us to put reconstructing lenses everywhere in the lattice, and to study their positioning scheme. Limits in linear response are analyzed. This sets the upper and lower limits in reconstruction to the phase advance measurement accuracy and the linear response regime limit.

MOPS069

Review of Beam Instabilities in the Presence of Electron Clouds in the LHC

760

K.S.B. Li, G. Rumolo
CERN, Geneva, Switzerland

Recent observations at the LHC indicate the build-up of electron clouds when 50 ns spaced beams are injected into the machine at nominal intensity. These electron clouds are a source of coherent beam instabilities and incoherent emittance growth and limit the achievable luminosity. To better understand the influence of electron clouds on the beam dynamics, simulations have been carried out to study both the coherent and the incoherent effects on the beam. The simulations are performed with the HeadTail tracking code; the usage of new post-processing software allows determining not only the beam intensity thresholds in terms of the central electron cloud density but also the footprint of the beam in tune space. In this paper we review instability thresholds and tune footprints for beams with different emittances and interacting with an electron cloud in field-free or dipole regions.

MOPS070

Electromagnetic Modeling of C Shape Ferrite Loaded Kickers

763

C. Zannini
EPFL, Lausanne, Switzerland
E. Métral, G. Rumolo, B. Salvant, V.G. Vaccaro, C. Zannini
CERN, Geneva, Switzerland

The kickers are major contributors to the CERN SPS beam coupling impedance. As such, they may represent a limitation to increasing the SPS bunch current in the frame of an intensity upgrade of the LHC. In this paper, analytical approach and CST Particle Studio time domain electromagnetic simulations are performed to obtain the longitudinal and transverse impedances/wake potentials of models of ferrite loaded kickers. It turns out that the existing models are not sufficient to characterize correctly these components from the coupling impedance point of view. In particular the results show that below few hundred MHz the real C-structure of the magnet cannot be neglected. Therefore an analytical model was developed and benchmarked with EM simulations to take into account the C-shape of the magnet.

MOPS071

Simulations of the Impedance of the New PS Wire Scanner Tank

766

B. Salvant
EPFL, Lausanne, Switzerland
W. Andreazza, F. Caspers, A. Grudiev, J.F. Herranz Alvarez, E. Métral, G. Rumolo
CERN, Geneva, Switzerland

The CERN PS is equipped with 4 wire scanners. It was identified that the small aperture of the current wire scanner tank causes beam losses and a new tank design was needed. The interaction of the PS bunches with the beam coupling impedance of this new tank may lead to beam degradation and wire damage. This contribution presents impedance studies of the current PS tank as well as the new design in order to assess the need to modify the design and/or install lossy materials plates dedicated to damp higher order cavity modes and reduce the total power deposited by the beam in the tank.

MOPS072

Broadband Electromagnetic Characterization of Materials for Accelerator Components

769

C. Zannini, A. Grudiev, E. Métral, T. Pieloni, G. Rumolo
CERN, Geneva, Switzerland
G. De Michele
PSI, Villigen, Switzerland
C. Zannini
EPFL, Lausanne, Switzerland

Electromagnetic (EM) characterization of materials up to high frequencies is a major requirement for the correct modeling of many accelerator components: collimators, kickers, high order modes damping devices for accelerating cavities. In this scenario, the coaxial line method has gained much importance compared to other methods because of its applicability in a wide range of frequencies. In this paper we describe a new coaxial line method that allows using only one measurement setup to characterize the material in a range of frequency from few MHz up to several GHz. A coaxial cable fed at one side is filled with the material under test and closed on a known load on the other side. The properties of the material are obtained from the measured reflection coefficient by using it as input for a transmission line (TL) model or for 3D EM simulations, which describe the measurements setup. We have applied this method to characterize samples of SiC (Silicon Carbide) which could be used for LHC collimators and for CLIC accelerating structures and NiZn ferrite used for kicker magnets.

MOPS075

Simulation of Multibunch Motion with the HEADTAIL Code and Application to the CERN SPS and LHC

778

N. Mounet
EPFL, Lausanne, Switzerland
N. Mounet, E. Métral, G. Rumolo
CERN, Geneva, Switzerland

Multibunch instabilities due to beam-coupling impedance can be a critical limitation for synchrotrons operating with many bunches. It is particularly true for the LHC under nominal conditions, where according to theoretical predictions the 2808 bunches rely entirely on the performance of the transverse feedback system to remain stable. To study these instabilities, the HEADTAIL code has been extended to simulate the motion of many bunches under the action of wake fields. All the features already present in the single-bunch version of the code, such as synchrotron motion, chromaticity, amplitude detuning due to octupoles and the ability to load any kind of wake fields through tables, have remained available. This new code has been then parallelized in order to track thousands of bunches in a reasonable amount of time. The code was benchmarked against theory and exhibited a good agreement. We also show results for bunch trains in the LHC and compare them with beam-based measurements.

TUPC011

Striplines for CLIC Pre-Damping and Damping Rings*

1012

C. Belver-Aguilar, A. Faus-Golfe
IFIC, Valencia, Spain
M.J. Barnes, G. Rumolo
CERN, Geneva, Switzerland
F. Toral
CIEMAT, Madrid, Spain
C. Zannini
EPFL, Lausanne, Switzerland

The Compact Linear Collider (CLIC) study explores the scheme for an electron-positron collider with high luminosity and a nominal center-of-mass energy of 3 TeV: CLIC would complement LHC physics in the multi-TeV range. The CLIC design relies on the presence of Pre-Damping Rings (PDR) and Damping Rings (DR) to achieve, through synchrotron radiation, the very low emittance needed to fulfil the luminosity requirements. The specifications for the kicker systems are very challenging and include very low beam coupling impedance and excellent field homogeneity: striplines have been chosen for the kicker elements. Analytical calculations have been carried out to determine the effect of tapering upon the high frequency beam coupling impedance. In addition detailed numerical modeling of the field homogeneity has been performed and the sensitivity of the homogeneity to various parameters, including stripline cross-section, has been studied. This paper presents the main conclusions of the beam impedance calculations and field homogeneity predictions.

TUPC050

Impedance Effects in the CLIC Damping Rings

1111

E. Koukovini, K.S.B. Li, N. Mounet, G. Rumolo, B. Salvant
CERN, Geneva, Switzerland

Due to the unprecedented brilliance of the beams, the performance of the Compact Linear Collider (CLIC) damping rings is affected by collective effects. Single bunch instability thresholds based on a broad-band resonator model and the associated coherent tune shifts have been evaluated with the HEADTAIL code. Simulations performed for positive and negative values of chromaticity proved that higher order bunch modes can be potentially dangerous for the beam stability. This study also includes the effects of high frequency resistive wall impedance due to different coatings applied on the chambers of the wigglers for e-cloud mitigation and/or ultra-low vacuum pressure. The impact of the resistive-wall wake fields on the transverse impedance budget is finally discussed.

TUPS028

Performance of Carbon Coating for Mitigation of Electron Cloud in the SPS

1590

C. Yin Vallgren, P. Chiggiato, P. Costa Pinto, H. Neupert, G. Rumolo, E.N. Shaposhnikova, M. Taborelli
CERN, Geneva, Switzerland

Amorphous carbon (a-C) coatings have been tested in electron cloud monitors (ECM) in the Super Proton Synchrotron (SPS) and have shown for LHC type beams a reduction of the EC current by a factor 10⁴ compared to stainless steel (SS). This performance has been maintained for more than 2 years under SPS operation conditions. Secondary electron yield (SEY) laboratory data confirm that after 1 year of SPS operation, the coating maintains a SEY below 1. The compatibility of coexisting SS and a-C surfaces has been studied in an ECM having coated and uncoated areas. The results show no degradation of the properties of the a-C areas. The performance of diamond like carbon (DLC) coating has also been studied. DLC shows a less effective reduction of the EC current than a-C, but conditioning is faster than for SS. Three a-C coated dipoles were inserted in the SPS. However, even with no EC detected, the dynamic pressure rise is similar to the one observed in the SS reference dipoles. Measurement in a new ECM equipped with clearing electrodes to verify the relation between pressure signals and intensity of the EC, as well as an improvement of the diagnostics in the dipoles are in progress.

TUPZ003

Simulation of Electron-cloud Build-Up for the Cold Arcs of the LHC and Comparison with Measured Data

1801

G.H.I. Maury Cuna
CINVESTAV, Mérida, Mexico
G. Arduini, G. Rumolo, L.J. Tavian, F. Zimmermann
CERN, Geneva, Switzerland

The electron cloud generated by synchrotron radiation or residual gas ionization is a concern for LHC operation and performance. We report the results of simulations studies which examine the electron cloud build-up, at injection energy, 3.5 TeV for various operation parameters In particular we determine the value of the secondary emission yield corresponding to the multipacting threshold, and investigate the electron density, and heat as a function of bunch intensity for dipoles and field-free regions. We also include a comparison between simulations results and measured heat-load data from the LHC scrubbing runs in 2011

TUPZ015

Electron Cloud Parameterization Studies in the LHC

1834

C.O. Domínguez, G. Arduini, V. Baglin, G. Bregliozzi, J.M. Jimenez, E. Métral, G. Rumolo, D. Schulte, F. Zimmermann
CERN, Geneva, Switzerland

During LHC beam commissioning with 150, 75 and 50-ns bunch spacing, important electron-cloud effects, like pressure rise, cryogenic heat load, beam instabilities or emittance growth, were observed. The main strategy to combat the LHC electron cloud relies on the surface conditioning arising from the chamber-surface bombardment with cloud electrons. In a standard model, the conditioning state of the beam-pipe surface is characterized by three parameters: 1. the secondary emission yield; 2. the incident electron energy at which the yield is maximum; and 3. the probability of elastic reflection of low-energy primary electrons hitting the chamber wall. Since at the LHC no in-situ secondary-yield measurements are available, we compare the relative local pressure-rise measurements taken for different beam configurations against simulations in which surface parameters are scanned. This benchmark of measurements and these simulations is used to infer the secondary-emission properties of the beam-pipe at different locations around the ring and at various stages of the surface conditioning. In this paper we present the methodology and first results from applying the technique to the LHC.

WEPC094

Energy Loss and Longitudinal Wakefield of Relativistic Short Ion Bunches in Electron Clouds

2229

F. Yaman, O. Boine-Frankenheim, E. Gjonaj, T. Weiland
TEMF, TU Darmstadt, Darmstadt, Germany
G. Rumolo
CERN, Geneva, Switzerland

Funding: Work supported by BMBF under contract 06DA9022I
The aim of our study is the numerical computation of the wakefield, impedance and energy loss for an energetic, short (< 10 ns) ion bunch penetrating an electron cloud plasma residing in the beam pipe. We use a 3-D self-consistent and higher order PIC code based on the full-wave solution of the Maxwell equations in the time domain. In our simulations we observe the induced density oscillations in the electron cloud in the longitudinal as well as in the transverse directions. A special numerical procedure is applied to compute the longitudinal wake potential and the broadband coupling impedance due to the beam-electron cloud interaction. The code is applied to the case of the CERN SPS and the projected SIS-100 at GSI. The effects of the beam pipe, electron density, bunch intensity and external magnetic dipole fields are studied. The results are compared to analytical and numerical models of reduced complexity.

WEPC135

Recent Developments in Modeling Time-resolved Shielded-pickup Measurements of Electron Cloud Buildup at CESRTA

2313

J.A. Crittenden, Y. Li, X. Liu, M.A. Palmer, J.P. Sikora
CLASSE, Ithaca, New York, USA
R.P. Badman
Syracuse University, Syracuse, USA
S. Calatroni, G. Rumolo
CERN, Geneva, Switzerland
S. Kato
KEK, Ibaraki, Japan

Funding: Work supported by the U.S. National Science Foundation PHY-0734867, PHY-1002467 and the U.S. Department of Energy DE-FC02-08ER41538
The Cornell Electron Storage Ring Test Accelerator program includes investigations into the mitigation of electron cloud buildup using a variety of techniques in custom vacuum chambers. The CESR ring accommodates two such chambers equipped with BPM-style pickup detectors shielded against the direct beam-induced signal. The signals provide time-resolved information on cloud development. Results for diamond-like carbon, amorphous carbon, and TiN coatings have been compared to those for an uncoated aluminum chamber. Here we report on extensions to the ECLOUD modeling code which refine its description of a variety of new types of in situ vacuum chamber comparisons. Our results highlight the sensitivity afforded by these measurements to the modeled photoelectron production and secondary yield parameters. We draw conclusions comparing the photoelectron and secondary yield properties of the various vacuum chamber coatings, including conditioning effects as a function of synchrotron radiation dose. We find substantial conditioning effects in both the quantum efficiency for producing photoelectrons and in the secondary yield.

THOBA01

Electron Cloud Observations in LHC

2862

G. Rumolo, G. Arduini, V. Baglin, H. Bartosik, P. Baudrenghien, N. Biancacci, G. Bregliozzi, S.D. Claudet, R. De Maria, J. Esteban Muller, M. Favier, C. Hansen, W. Höfle, J.M. Jimenez, V. Kain, E. Koukovini, G. Lanza, K.S.B. Li, G.H.I. Maury Cuna, E. Métral, G. Papotti, T. Pieloni, F. Roncarolo, B. Salvant, E.N. Shaposhnikova, R.J. Steinhagen, L.J. Tavian, D. Valuch, W. Venturini Delsolaro, F. Zimmermann
CERN, Geneva, Switzerland
C.M. Bhat
Fermilab, Batavia, USA
U. Iriso
CELLS-ALBA Synchrotron, Cerdanyola del Vallès, Spain
N. Mounet, C. Zannini
EPFL, Lausanne, Switzerland

Operation of LHC with bunch trains different spacings has revealed the formation of an electron cloud inside the machine. The main observations of electron cloud build-up are the pressure rise measured at the vacuum gauges in the warm regions, as well as the increase of the beam screen temperature in the cold regions due to an additional heat load. The effects of the electron cloud were also visible as a strong instability and emittance growth affecting the last bunches of longer trains, which could be improved running with higher chromaticity and/or larger transverse emittances. A summary of the 2010 and 2011 observations and measurements and a comparison with existing models will be presented. The efficiency of scrubbing and scrubbing strategies to improve the machine running performance will be also briefly discussed.

Slides THOBA01 [2.911 MB]

MOPS009

Probing Intensity Limits of LHC-type Bunches in the CERN SPS with Nominal Optics

610

B. Salvant, G. Adrian, D.J. Allen, O. Andujar, T. Argyropoulos, J. Axensalva, J. Baldy, H. Bartosik, S. Cettour Cave, F. Chapuis, J.F. Comblin, K. Cornelis, D.G. Cotte, K. Cunnington, H. Damerau, M. Delrieux, J.L. Duran-Lopez, A. Findlay, J. Fleuret, F. Follin, P. Freyermuth, H. Genoud, S.S. Gilardoni, A. Guerrero, S. Hancock, K. Hanke, O. Hans, R. Hazelaar, W. Höfle, L.K. Jensen, J. Kuczerowski, Y. Le Borgne, R. Maillet, D. Manglunki, S. Massot, E. Matli, G. Metral, B. Mikulec, E. Métral, J.-M. Nonglaton, E. Ovalle, L. Pereira, F.C. Peters, A. Rey, J.P. Ridewood, G. Rumolo, J.L. Sanchez Alvarez, E.N. Shaposhnikova, R.R. Steerenberg, R.J. Steinhagen, J. Tan, B. Vandorpe, E. Veyrunes
CERN, Geneva, Switzerland

Some of the upgrade scenarios of the high-luminosity LHC require large intensity per bunch from the injector chain. Single bunch beams with intensities of up to 3.5 to 4·10¹¹ p/b and nominal emittances were successfully produced in the PS Complex and delivered to the SPS in 2010. This contribution presents results of studies with this new intense beam in the SPS to probe single bunch intensity limitations with nominal gamma transition. In particular, the vertical Transverse Mode Coupling Instability (TMCI) threshold with low chromaticity was observed at 1.6·10¹¹ p/b for single nominal LHC bunches in the SPS. With increased vertical chromaticity, larger intensities could be injected, stored along the flat bottom and accelerated up to 450 GeV/c. However, significant losses and/or transverse emittance blow up were then observed. Longitudinal and transverse optimization efforts in the PSB, PS and SPS were put in place to minimize this beam degradation and succeeded to obtain single 2.3·10¹¹ p/b LHC type bunches with satisfying parameters at extraction of the SPS.

MOPS083

Update on Electron Cloud Mitigation Studies at Cesr-TA*

796

J.R. Calvey, M.G. Billing, J.V. Conway, G. Dugan, S. Greenwald, Y. Li, X. Liu, J.A. Livezey, J. Makita, R.E. Meller, M.A. Palmer, S. Santos, R.M. Schwartz, J.P. Sikora, C.R. Strohman
CLASSE, Ithaca, New York, USA
S. Calatroni, G. Rumolo
CERN, Geneva, Switzerland
K. Kanazawa, Y. Suetsugu
KEK, Ibaraki, Japan
M.T.F. Pivi, L. Wang
SLAC, Menlo Park, California, USA

Funding: Work supported by the US National Science Foundation (PHY-0734867) and Department of Energy (DE-FC02-08ER41538)
Over the course of the past three years, the Cornell Electron Storage Ring (CESR) has been reconfigured to serve as a test facility for next generation particle accelerators. A significant part of this program has been the installation of several diagnostic devices to measure and quantify the electron cloud effect, a potential limiting factor in these machines. In particular, more than 30 Retarding Field Analyzers (RFAs) have been installed in CESR. These devices measure the local electron cloud density and energy distribution, and can be used to evaluate the efficacy of different cloud mitigation techniques. This paper will provide an overview of RFA results obtained at CesrTA over the past year, including measurements taken as function of bunch spacing and wiggler magnetic field. Understanding these results provides a great deal of insight into the behavior of the electron cloud.

WEPS018

The Proposed CERN Proton-Synchrotron Upgrade Program

2520

S.S. Gilardoni, S. Bart Pedersen, W. Bartmann, S. Bartolome, O.E. Berrig, C. Bertone, A. Blas, D. Bodart, J. Borburgh, R.J. Brown, A.C. Butterworth, M.C.L. Buzio, C. Carli, P. Chiggiato, H. Damerau, T. Dobers, R. Folch, R. Garoby, B. Goddard, M. Gourber-Pace, S. Hancock, M. Hourican, P. Le Roux, L.A. Lopez Hernandez, A. Masi, G. Metral, Y. Muttoni, E. Métral, M. Nonis, J. Pierlot, S. Pittet, C. Rossi, I. Ruehl, G. Rumolo, L. Sermeus, R.R. Steerenberg, M. Widorski
CERN, Geneva, Switzerland

In the framework of the High-Luminosity LHC project, the CERN Proton Synchrotron would require a major upgrade to match the future beam parameters requested as pre-injector of the collider. The different beam dynamics issues, from space-charge limitations to longitudinal instabilities are discussed, as well as the proposed technical solutions to overcome them, covering the increase of the injection energy to RF related improvements.