IPAC2011 - List of Authors (Glock, H.-W.)

Paper	Title	Page
MOPC080	First Considerations Concerning an Optimized Cavity Design for the Main Linac of BERLinPro	259
	B. Riemann, T. Weis DELTA, Dortmund, Germany W. Anders, J. Knobloch, A. Neumann HZB, Berlin, Germany H.-W. Glock, C. Potratz, U. van Rienen Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany F. Marhauser JLAB, Newport News, Virginia, USA
	Funding: work supported by BMBF under contracts 05K10PEA and 05K10HRC The Berlin Energy Recovery Linac Project (BERLinPro) is designed to develop and demonstrate CW linac technology and expertise required to drive next-generation Energy Recovery Linacs. Strongly HOM-damped multicell 1.3 GHz cavities are required for the main linac. The optimization of the cavities presented here is primarily based on the CEBAF 1.5 GHz 5-cell high-current cavity design, including HOM waveguide couplers. The cavity was scaled to 1.3 GHz and extended to 7 cells. Modifications to the end group design have also been studied. An effort was also made to reduce the ratio Epk/Eacc while still permitting HOMs to propagate.

WEPC096	Calculation of High Frequency Fields in Resonant Cavities Based on Perturbation Theory*	2235
	K. Brackebusch, H.-W. Glock, U. van Rienen Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
	Funding: Work supported by Federal Ministry for Research and Education BMBF under contracts 05H09HR5 and 05K10HRC. The knowledge of the eigenmodes of resonant accelerator cavities is essential for the determination of their performance characteristics, comprising resonant frequencies and field distributions inside the cavities. Apart from the material properties the eigenmodes of a cavity depend on its geometry. In spite of the high elaborateness during the complex fabrication process, minor deviations of the actual cavity shape from the desired one are inevitable. Moreover, especially superconducting cavities are subject to extreme operating conditions that may cause deformations of their shape. Any geometry perturbation results in a shift of the resonant frequencies and modified field distributions. In this paper, we will analyze a generalization of Slater's theorem proposed in literature. The method should allow for the calculation of resonant frequencies and field distributions of a slightly perturbed cavity by using a set of precomputed eigenmodes of the unperturbed cavity. We will evaluate the practicability of the method by applying it to cavity geometries for which the eigenmodes are analytically known, ascertain the effort of reasonable calculation results and describe its limitations.

WEPC097	A Concatenation Scheme for the Computation of Beam Excited Higher Order Mode Port Signals	2238
	T. Flisgen, H.-W. Glock, U. van Rienen Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
	Ongoing studies investigate in how far higher order mode (HOM) port signals of superconducting RF cavities can be used for machine and beam diagnostics. Apart from experiments e.g. at the FLASH facility at DESY in Hamburg, numerical modelling is needed for the prediction of HOM coupler signals. For this purpose, the RF properties of the entire accelerating module have to be taken into account, since higher order modes can propagate along the cavity chain. A discretization of the full chain, followed by a wake field simulation is only feasible with powerful and expensive cluster computers. Instead, an element wise wake field simulation of sub-sections of the chain, followed by a suitable concatenation scheme can be performed on standard hardware assuming the beam to be sufficiently stiff. In this paper a concatenation scheme for the computation of beam excited HOM port signals is derived as a generalization of the Coupled S-Parameter scheme CSC. Furthermore, the validity of the method is shown for a sample structure.

WEPC098	Automatic Pole and Q-Value Extraction for RF Structures	2241
	C. Potratz, H.-W. Glock, U. van Rienen Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany F. Marhauser JLAB, Newport News, Virginia, USA
	The experimental characterization of RF structures like accelerating cavities often demands for measuring resonant frequencies of Eigenmodes and corresponding (loaded) Q-values over a wide spectral range. A common procedure to determine the Q-values is the -3dB method, which works well for isolated poles, but may not be applicable directly in case of multiple poles residing in close proximity (e.g. for adjacent transverse modes differing by polarization). Although alternative methods may be used in such cases, this often comes at the expense of inherent systematic errors. We have developed an automation algorithm, which not only speeds up the measurement time significantly, but is also able to extract Eigenfrequencies and Q-values both for well isolated and overlapping poles. At the same time the measurement accuracy may be improved as a major benefit. To utilize this procedure merely complex scattering parameters have to be recorded for the spectral range of interest. In this paper we present the proposed algorithm applied to experimental data recorded for superconducting higher-order-mode damped multi-cell cavities as an application of high importance.

WEPC099	Coupler Design and Optimization by GPU-Accelerated DG-FEM	2244
	C. Potratz, H.-W. Glock, U. van Rienen Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
	The numerical optimization of rf-components like couplers is a common task during the design phase of particle accelerators. Typically, these optimizations involve the simulation of a multitude of very similar structures with minor geometric variations. Nevertheless, this process is in its entire extend rather demanding on both the invested time and hardware budget. With recent advancements in the field of numerical electromagnetic field simulation and consumer graphic processors, an interesting alternative for the time-consuming simulation part of the optimization is available. In this contribution we show, how the Discontinuous Galerkin FEM method in conjunction with consumer graphic cards can be used to build moderately prized cluster solutions for the parallel simulation of rf-components. The contribution will mainly focus on, but is not limited to, Higher Order Mode couplers as a typical application example, where the DG-FEM method accelerated by a graphic processor might be used to significantly reduce the overall time necessary for the optimization.

Paper

Title

Page

First Considerations Concerning an Optimized Cavity Design for the Main Linac of BERLinPro

259

B. Riemann, T. Weis
DELTA, Dortmund, Germany
W. Anders, J. Knobloch, A. Neumann
HZB, Berlin, Germany
H.-W. Glock, C. Potratz, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
F. Marhauser
JLAB, Newport News, Virginia, USA

Funding: work supported by BMBF under contracts 05K10PEA and 05K10HRC
The Berlin Energy Recovery Linac Project (BERLinPro) is designed to develop and demonstrate CW linac technology and expertise required to drive next-generation Energy Recovery Linacs. Strongly HOM-damped multicell 1.3 GHz cavities are required for the main linac. The optimization of the cavities presented here is primarily based on the CEBAF 1.5 GHz 5-cell high-current cavity design, including HOM waveguide couplers. The cavity was scaled to 1.3 GHz and extended to 7 cells. Modifications to the end group design have also been studied. An effort was also made to reduce the ratio Epk/Eacc while still permitting HOMs to propagate.

WEPC096

Calculation of High Frequency Fields in Resonant Cavities Based on Perturbation Theory*

2235

K. Brackebusch, H.-W. Glock, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany

Funding: Work supported by Federal Ministry for Research and Education BMBF under contracts 05H09HR5 and 05K10HRC.
The knowledge of the eigenmodes of resonant accelerator cavities is essential for the determination of their performance characteristics, comprising resonant frequencies and field distributions inside the cavities. Apart from the material properties the eigenmodes of a cavity depend on its geometry. In spite of the high elaborateness during the complex fabrication process, minor deviations of the actual cavity shape from the desired one are inevitable. Moreover, especially superconducting cavities are subject to extreme operating conditions that may cause deformations of their shape. Any geometry perturbation results in a shift of the resonant frequencies and modified field distributions. In this paper, we will analyze a generalization of Slater's theorem proposed in literature. The method should allow for the calculation of resonant frequencies and field distributions of a slightly perturbed cavity by using a set of precomputed eigenmodes of the unperturbed cavity. We will evaluate the practicability of the method by applying it to cavity geometries for which the eigenmodes are analytically known, ascertain the effort of reasonable calculation results and describe its limitations.

WEPC097

A Concatenation Scheme for the Computation of Beam Excited Higher Order Mode Port Signals

2238

T. Flisgen, H.-W. Glock, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany

Ongoing studies investigate in how far higher order mode (HOM) port signals of superconducting RF cavities can be used for machine and beam diagnostics. Apart from experiments e.g. at the FLASH facility at DESY in Hamburg, numerical modelling is needed for the prediction of HOM coupler signals. For this purpose, the RF properties of the entire accelerating module have to be taken into account, since higher order modes can propagate along the cavity chain. A discretization of the full chain, followed by a wake field simulation is only feasible with powerful and expensive cluster computers. Instead, an element wise wake field simulation of sub-sections of the chain, followed by a suitable concatenation scheme can be performed on standard hardware assuming the beam to be sufficiently stiff. In this paper a concatenation scheme for the computation of beam excited HOM port signals is derived as a generalization of the Coupled S-Parameter scheme CSC. Furthermore, the validity of the method is shown for a sample structure.

WEPC098

Automatic Pole and Q-Value Extraction for RF Structures

2241

C. Potratz, H.-W. Glock, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
F. Marhauser
JLAB, Newport News, Virginia, USA

The experimental characterization of RF structures like accelerating cavities often demands for measuring resonant frequencies of Eigenmodes and corresponding (loaded) Q-values over a wide spectral range. A common procedure to determine the Q-values is the -3dB method, which works well for isolated poles, but may not be applicable directly in case of multiple poles residing in close proximity (e.g. for adjacent transverse modes differing by polarization). Although alternative methods may be used in such cases, this often comes at the expense of inherent systematic errors. We have developed an automation algorithm, which not only speeds up the measurement time significantly, but is also able to extract Eigenfrequencies and Q-values both for well isolated and overlapping poles. At the same time the measurement accuracy may be improved as a major benefit. To utilize this procedure merely complex scattering parameters have to be recorded for the spectral range of interest. In this paper we present the proposed algorithm applied to experimental data recorded for superconducting higher-order-mode damped multi-cell cavities as an application of high importance.

WEPC099

Coupler Design and Optimization by GPU-Accelerated DG-FEM

2244

C. Potratz, H.-W. Glock, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany

The numerical optimization of rf-components like couplers is a common task during the design phase of particle accelerators. Typically, these optimizations involve the simulation of a multitude of very similar structures with minor geometric variations. Nevertheless, this process is in its entire extend rather demanding on both the invested time and hardware budget. With recent advancements in the field of numerical electromagnetic field simulation and consumer graphic processors, an interesting alternative for the time-consuming simulation part of the optimization is available. In this contribution we show, how the Discontinuous Galerkin FEM method in conjunction with consumer graphic cards can be used to build moderately prized cluster solutions for the parallel simulation of rf-components. The contribution will mainly focus on, but is not limited to, Higher Order Mode couplers as a typical application example, where the DG-FEM method accelerated by a graphic processor might be used to significantly reduce the overall time necessary for the optimization.