ANL, Argonne
Northern Illinois University, DeKalb, Illinois
Funding: This work was supported by the U.S. Department of Energy, Office of Nuclear Physics, under contract number DE-AC02-06CH11357.
We have developed a pepper pot - scintillator screen system to measure the emittance of low-energy dc beams extracted from an ECR ion source and post-accelerated to an energy of 75 - 90 keV/charge. Different scintillators have been tested and CsI (Tl) was chosen due to its high sensitivity, wide dynamic range and long life-time. The linearity of both the scintillator and the CCD camera has been studied. A LabVIEW code has been developed and used for on-line emittance measurements. Un-normalized rms emittances measured for 209Bi20+ and 209Bi21+ beams with current of 1.0 - 1.5 pnA are usually ~30 π mm.mrad. A complicated structure of multiple images of individual holes has been observed. The innovative combination of a special type of scintillator, a CCD camera and a fast shutter allowed us to create a very efficient emittance meter for low-energy dc ion beams. Using on-line emittance measurements, it was possible to improve the beam quality by re-tuning the ion source conditions. Because of the two-dimensional array of holes in the pepper-pot, this emittance meter can be used to observe and study four-dimensional emittance correlations in beams from ECR ion sources.
Kyoto ICR, Uji, Kyoto
We aim to develop a small and high intensity proton source for a compact accelerator based neutron source. Because this proton source shall be located close to RFQ for simplification, ratio of H+ to molecular ions such as H2+ or H3+ must be large. Therefore we select ECR ion source with permanent magnet as a small and high intensity ion source. ECR ion sources can provide high H+ ratio because of their high plasma temperature. Using permanent magnets makes the ion source small and running cost low. Because there is no hot cathode, longer MTBF is expected. Usually, gas is fed into ion sources continuously, even if ion sources run in pulse operation mode. But, continuous gas flow doesn't make vacuum in good level. So, we decided to install pulse gas valve directly to the plasma chamber. Feeding the gas only when the ion source is in operation reduces the gas load to the evacuation system and the vacuum level can be kept high. Recent experimental results will be presented.
ANL, Argonne
Northern Illinois University, DeKalb, Illinois
Funding: This work was supported by the U.S. Department of Energy, Office of Nuclear Physics, under Contract No. DE-AC-02-06CH11357.
A prototype injector capable to produce multiple-charge-state heavy-ion beams is being developed at ANL. The injector consists of an ECR ion source, a 100 kV platform and a Low Energy Beam Transport (LEBT). The latter comprises two 60-degree bending magnets, electrostatic triplets and beam diagnostics stations. Several charge states of bismuth ions from the ECR have been extracted, accelerated to an energy of 1.8 MeV, separated and then recombined into a high quality beam ready for further acceleration. This technique allows us to double heavy-ion beam intensity in high-power driver linac for future radioactive beam facility. The other application is the post-accelerators of radioactive ions based on charge breeders. The intensity of rare isotope beams can be doubled or even tripled by the extraction and acceleration of multiple charge state beams. We will report the results of emittance measurements of multiple-charge state beams after recombination.
LANL, Los Alamos, New Mexico
Funding: This work was supported by the US Department of Energy under Contract Number DE-AC52-06NA25396
For the purpose of this presentation, the term Linac is narrowed down to comprise rf machines that accelerate ion beams at duty factors between about 5% and continuous operation. This group of Linacs includes proton and H- machines as well as accelerators utilizing multi-charged heavy ions, mostly for nuclear physics applications. Main types of ion sources serving these Linacs include Electron Cyclotron Resonance (ECR) sources, filament and rf driven multi-cusp sources, Penning (PIG) sources and duoplasmatrons. This presentation does not strive to attain encyclopedic character but rather to highlight current trends in performance parameters, major lines of development and type-specific limitations and problems, with emphasis on ECR and multi-cusp sources. The main technical aspects being discussed are ion production and beam formation.
