GSI, Darmstadt
Experimental results from ion beams, extracted from an Electron Cyclotron Resonance ion source (ECRIS) are presented and compared with different models used for simulation. The model for the simulation has to satisfy different facts: The energy of ions within the plasma is in the eV-range. Electrons have a different energy distribution: there are hot electrons (up to MeV range), but also low energy electrons, responsible for charge neutrality within the plasma. Because the gyration radius of ions is within the mm-range and below, ions can be extracted only if they are located on a magnetic field line which goes through the extraction aperture. Because of the gradient dBz/dz of the mirror field only these ions can be extracted, which have enough energy in direction of the field line. These conditions are fulfilled for ions which are going to be lost through the loss cone created by the hexapole. The extracted beam shows a typical behavior for an ECRIS: when the beam is focused by a lens (here a solenoid) directly behind extraction, the initial round and hollow beam develops wings with a 120-degree symmetry. These wings has influence on the beam emittance.
Kyoto ICR, Uji, Kyoto
We aim to develop a small and high intensity proton source for a compact accelerator based neutron source. Because this proton source shall be located close to RFQ for simplification, ratio of H+ to molecular ions such as H2+ or H3+ must be large. Therefore we select ECR ion source with permanent magnet as a small and high intensity ion source. ECR ion sources can provide high H+ ratio because of their high plasma temperature. Using permanent magnets makes the ion source small and running cost low. Because there is no hot cathode, longer MTBF is expected. Usually, gas is fed into ion sources continuously, even if ion sources run in pulse operation mode. But, continuous gas flow doesn't make vacuum in good level. So, we decided to install pulse gas valve directly to the plasma chamber. Feeding the gas only when the ion source is in operation reduces the gas load to the evacuation system and the vacuum level can be kept high. Recent experimental results will be presented.
ANL, Argonne
Northern Illinois University, DeKalb, Illinois
Funding: This work was supported by the U.S. Department of Energy, Office of Nuclear Physics, under Contract No. DE-AC-02-06CH11357.
A prototype injector capable to produce multiple-charge-state heavy-ion beams is being developed at ANL. The injector consists of an ECR ion source, a 100 kV platform and a Low Energy Beam Transport (LEBT). The latter comprises two 60-degree bending magnets, electrostatic triplets and beam diagnostics stations. Several charge states of bismuth ions from the ECR have been extracted, accelerated to an energy of 1.8 MeV, separated and then recombined into a high quality beam ready for further acceleration. This technique allows us to double heavy-ion beam intensity in high-power driver linac for future radioactive beam facility. The other application is the post-accelerators of radioactive ions based on charge breeders. The intensity of rare isotope beams can be doubled or even tripled by the extraction and acceleration of multiple charge state beams. We will report the results of emittance measurements of multiple-charge state beams after recombination.
ORNL, Oak Ridge, Tennessee
ORNL RAD, Oak Ridge, Tennessee
Funding: *SNS is managed by UT-Battelle, LLC, under contract DE-AC05-00OR22725 for the U.S. Department of Energy
During the first three years, the Spallation Neutron Source is ramping up the rep rate, pulse length, and beam current to reach 1 to 1.4 MW beam power in 2009. This challenges the Front-end with the H- source designed and built by Lawrence Berkeley National Laboratory. Early in 2007, the low-energy beam transport needed to be modified to improve the availability for duty factors in excess of 0.2%. Late in 2007, the H- source needed to be modified to produce the required 25 mA LINAC beam current during the ~0.4 ms long pulses at 60 Hz. The optimistic 1.4 MW goal requires 38 mA LINAC beam current, which was demonstrated for 4 hours on 12/24/07. LBNL developed a cesium system that uses only 30 mg of Cs to minimize the risk to the adjacent electrostatic LEBT and RFQ. Improved procedures and configuration were needed to generate intense beam currents for long pulses (>0.2 ms). Now optimal beam currents are reached within eight hours of replacing the H- source. The beam decay appears to be as small as 1% per day, which is compensated by a gradual increase in rf power. The peak performance can be restored by slowly re-cesiating the converter without interupting the neutron production.
BNL, Upton, Long Island, New York
IAP, Frankfurt am Main
Funding: Work supported by the US Department of Energy and the National Aeronautics and Space Agency
A new heavy ion preinjector is presently under construction at Brookhaven National Laboratory. This preinjector uses an Electron Beam Ion Source (EBIS), and an RFQ and IH Linac, both operating at 100 MHz, to produce 2 MeV/u ions of any species for use, after further acceleration, at the Relativistic Heavy Ion Collider, and the NASA Space Radiation Laboratory. Among the increased capabilities provided by this preinjector are the ability to produce ions of any species, and the ability to switch between multiple species in 1 second, to simultaneously meet the needs of both physics programs. Fabrication of all major components for this preinjector is in process, with testing of the EBIS and RFQ starting this year. The status of this construction will be presented.
LANL, Los Alamos, New Mexico
Funding: This work was supported by the US Department of Energy under Contract Number DE-AC52-06NA25396
For the purpose of this presentation, the term Linac is narrowed down to comprise rf machines that accelerate ion beams at duty factors between about 5% and continuous operation. This group of Linacs includes proton and H- machines as well as accelerators utilizing multi-charged heavy ions, mostly for nuclear physics applications. Main types of ion sources serving these Linacs include Electron Cyclotron Resonance (ECR) sources, filament and rf driven multi-cusp sources, Penning (PIG) sources and duoplasmatrons. This presentation does not strive to attain encyclopedic character but rather to highlight current trends in performance parameters, major lines of development and type-specific limitations and problems, with emphasis on ECR and multi-cusp sources. The main technical aspects being discussed are ion production and beam formation.