HB2012 - List of Authors (Bustinduy, I.)

Paper

Title

Page

Medium Energy Beam Transport Design Update for ESS

128

I. Bustinduy, F.J. Bermejo, A. Ghiglino, O. González, J.L. Muñoz, I. Rodríguez, A. Zugazaga
ESS Bilbao, Bilbao, Spain
B. Cheymol, M. Eshraqi, R. Miyamoto
ESS, Lund, Sweden
J. Stovall
CERN, Geneva, Switzerland

The major challenge of this part of the accelerator is to keep a high quality beam, with a pulse well defined in time, a low emittance and a minimized halo, so that the beam losses downstream the linac be limited and the overall ESS reliability be maximized. In order to minimize beam loss at high energy linac, and the consequent activation of components, a fast chopping scheme is presented for the medium energy beam transport section (MEBT). The considered versatile MEBT is being designed to achieve four main goals: First, to contain a fast chopper and its correspondent beam dump, that could serve in the commissioning as well as in the ramp up phases. Second, to serve as a halo scraping section by means of two adjustable blades. Third, to measure the beam phase and profile between the RFQ and the DTL, along with other beam monitors. And finally, to match the RFQ output beam characteristics to the DTL input both transversally and longitudinally. For this purpose a set of ten quadrupoles is used to match the beam characteristics transversally, combined with two 352.2 MHz buncher cavities, which are used to adjust the beam in order to fulfill the required longitudinal parameters.

TUO3B01

Beam Dynamics Design of ESS Warm Linac

274

M. Comunian, F. Grespan, A. Pisent
INFN/LNL, Legnaro (PD), Italy
I. Bustinduy
ESS Bilbao, Bilbao, Spain
L. Celona, S. Gammino, L. Neri
INFN/LNS, Catania, Italy
R. De Prisco
Lund University, Lund, Sweden
M. Eshraqi, R. Miyamoto, A. Ponton
ESS, Lund, Sweden

In the present design of the European Spallation Source (ESS) accelerator, the Warm Linac will accelerate a pulsed proton beam of 50 mA peak current from source at 0.075 MeV up to 80 MeV. Such Linac is designed to operate at 352.2 MHz, with a duty cycle of 4% (3 ms pulse length, 14 Hz repetition period).In this paper the main design choices and the beam dynamics studies for the source up to the end of DTL are shown.

Slides TUO3B01 [17.664 MB]

WEO3A02

Beam Loss and Collimation in the ESS Linac

368

R. Miyamoto, B. Cheymol, H. Danared, M. Eshraqi, A. Ponton, J. Stovall, L. Tchelidze
ESS, Lund, Sweden
I. Bustinduy
ESS Bilbao, Bilbao, Spain
A.I.S. Holm, S.P. Møller, H.D. Thomsen
ISA, Aarhus, Denmark

The European Spallation Source (ESS), to be built in Lund, Sweden, is a spallation neutron source based on a 5 MW proton linac. A high power proton linac has a tight tolerance on beam losses to avoid activation of its components and it is ideal to study patterns of the beam loss and prepare beam loss mitigation schemes at the design stage. This paper presents simulations of the beam loss in the ESS linac as well as beam loss mitigation schemes using collimators in beam transport sections.

Slides WEO3A02 [6.377 MB]

Paper	Title	Page
MOP235	Medium Energy Beam Transport Design Update for ESS	128
	I. Bustinduy, F.J. Bermejo, A. Ghiglino, O. González, J.L. Muñoz, I. Rodríguez, A. Zugazaga ESS Bilbao, Bilbao, Spain B. Cheymol, M. Eshraqi, R. Miyamoto ESS, Lund, Sweden J. Stovall CERN, Geneva, Switzerland
	The major challenge of this part of the accelerator is to keep a high quality beam, with a pulse well defined in time, a low emittance and a minimized halo, so that the beam losses downstream the linac be limited and the overall ESS reliability be maximized. In order to minimize beam loss at high energy linac, and the consequent activation of components, a fast chopping scheme is presented for the medium energy beam transport section (MEBT). The considered versatile MEBT is being designed to achieve four main goals: First, to contain a fast chopper and its correspondent beam dump, that could serve in the commissioning as well as in the ramp up phases. Second, to serve as a halo scraping section by means of two adjustable blades. Third, to measure the beam phase and profile between the RFQ and the DTL, along with other beam monitors. And finally, to match the RFQ output beam characteristics to the DTL input both transversally and longitudinally. For this purpose a set of ten quadrupoles is used to match the beam characteristics transversally, combined with two 352.2 MHz buncher cavities, which are used to adjust the beam in order to fulfill the required longitudinal parameters.

TUO3B01	Beam Dynamics Design of ESS Warm Linac	274
	M. Comunian, F. Grespan, A. Pisent INFN/LNL, Legnaro (PD), Italy I. Bustinduy ESS Bilbao, Bilbao, Spain L. Celona, S. Gammino, L. Neri INFN/LNS, Catania, Italy R. De Prisco Lund University, Lund, Sweden M. Eshraqi, R. Miyamoto, A. Ponton ESS, Lund, Sweden
	In the present design of the European Spallation Source (ESS) accelerator, the Warm Linac will accelerate a pulsed proton beam of 50 mA peak current from source at 0.075 MeV up to 80 MeV. Such Linac is designed to operate at 352.2 MHz, with a duty cycle of 4% (3 ms pulse length, 14 Hz repetition period).In this paper the main design choices and the beam dynamics studies for the source up to the end of DTL are shown.
	Slides TUO3B01 [17.664 MB]

WEO3A02	Beam Loss and Collimation in the ESS Linac	368
	R. Miyamoto, B. Cheymol, H. Danared, M. Eshraqi, A. Ponton, J. Stovall, L. Tchelidze ESS, Lund, Sweden I. Bustinduy ESS Bilbao, Bilbao, Spain A.I.S. Holm, S.P. Møller, H.D. Thomsen ISA, Aarhus, Denmark
	The European Spallation Source (ESS), to be built in Lund, Sweden, is a spallation neutron source based on a 5 MW proton linac. A high power proton linac has a tight tolerance on beam losses to avoid activation of its components and it is ideal to study patterns of the beam loss and prepare beam loss mitigation schemes at the design stage. This paper presents simulations of the beam loss in the ESS linac as well as beam loss mitigation schemes using collimators in beam transport sections.
	Slides WEO3A02 [6.377 MB]