Paper |
Title |
Page |
MOPB080 |
The Stable Operation of MPG and Measurement of Output |
254 |
|
- B.T. Li, X.Y. Lu, L. Xiao, D.Y. Yang, Y. Yang, Z.Q. Yang, J. Zhao
PKU, Beijing, People's Republic of China
|
|
|
The concept of micro-pulse electron gun(MPG) was proposed decades ago. It can provide electron beam with high current, short pulse and low emittance. But it is still not put into practical use as electron source because of its unsteady operating state. This paper presents an experimental result of the steady running of MPG which can operate stably for more than ten hours. The energy spread of the electron beam is also measured, the peak is located at near 20eV and half width is less than 15eV .
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-SRF2017-MOPB080
|
|
Export • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
MOPB082 |
A Preliminary Scheme for X-ray Emission Based on Micro-pulse Electron Gun |
259 |
|
- Y. Yang, B.T. Li, X.Y. Lu, W.W. Tan, L. Xiao, D.Y. Yang, Z.Q. Yang, J. Zhao
PKU, Beijing, People's Republic of China
|
|
|
X-ray is now widely used in many areas of physics, biology, chemistry and materials. And how to achieve emission, monochrome, and focusing of x-ray is of great significance to study. Micro-pulse electron gun (MPG) is a new type of electron source, with characteristics of high repetition frequency, short-pulse and low cost. Generating x-ray with better monochromaticity is one of the potential applications of MPG. And a preliminary scheme of X-ray based on MPG is proposed in this paper. The scheme is designed by comparing different anode materials and the thickness of filters. The simulation results based on the software MCNP5 show that the proposed scheme can effectively improve the monotonicity of the generated X-rays.
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-SRF2017-MOPB082
|
|
Export • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
TUPB055 |
Nb3Sn Thin Film Deposition On Copper By DC Magnetron Sputtering |
512 |
|
- W.W. Tan, B.T. Li, X.Y. Lu, L. Xiao, D. Xie, D.Y. Yang, Y. Yang, Z.Q. Yang, J. Zhao
PKU, Beijing, People's Republic of China
|
|
|
Nb3Sn for SRF cavities has been coated on copper samples by DC magnetron Sputtering. Pure Nb target and pure Sn target were installed separately in the magnetron sputtering device. Nb3Sn precursor was coated on copper in the Ar atmosphere of 0.5 Pa. The Nb3Sn precursor was annealed in the vacuum furnace whose pressure is 10-4 Pa. The XRD results demonstrate the exist of Nb3Sn crystal, and MPMS results show superconductivity of Nb3Sn. The highest critical temperature obtained is 15K.
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-SRF2017-TUPB055
|
|
Export • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|