NAPAC2019 - List of Keywords (septum)

Paper	Title	Other Keywords	Page
MOPLM01	Alternative Injection Schemes to the NSLS-II Using Nonlinear Injection Magnets	injection, kicker, storage-ring, multipole	91
	R.P. Fliller, III, G. Bassi, A. Blednykh, C. Hetzel, V.V. Smaluk, C.J. Spataro, P. Zuhoski BNL, Upton, New York, USA
	Funding: This manuscript has been authored by Brookhaven Science Associates, LLC under Contract No. DE-SC0012704 with the U.S. Department of Energy The NSLS-II storage ring uses the standard four bump injection scheme to inject beam off axis. BESSY and MAX IV are now using a pulsed multipole magnet as an injection kicker. The injected beam sees a field off axis for injection while the stored beam experiences no field on the magnet axis. The principle advantage of using a pulsed multipole for injection is that the stored beam motion is greatly reduced since the field on axis is negligible. The number of pulsed magnets is reduced from five in the nominal scheme (septum and four bumps) to two or three thereby reducing the possible failure modes. This also eliminates the need to precisely match the pulse shapes of four dipole magnets to achieve minimal stored beam motion outside of the bump. In this paper we discuss two schemes of injecting into the NSLS-II using a pulsed multipole magnet. The first scheme uses a single pulsed multipole located in one cell downstream of the injection septum as the injection kicker. The second scheme uses two pulsed multipoles in the injection straight to perform the injection. We discuss both methods of injection and compare each method.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-MOPLM01
About •	paper received ※ 27 August 2019 paper accepted ※ 05 September 2019 issue date ※ 08 October 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPLM10	Simulation Study With Septum Field Map for the APS Upgrade	simulation, magnet-design, injection, photon	116
	A. Xiao, M. Abliz, M. Borland ANL, Lemont, Illinois, USA
	Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. One of the biggest challenges faced by the Advanced Photon Source Upgrade injection system design is the septum magnet. Not only does the required leakage field inside the stored beam chamber need to be smaller than for the present ring, the magnet has to be slightly tilted about the z-axis to provide a gentle vertical bend that brings the injected beam trajectory close to y=0 when it passes through the storage ring quadrupole magnets upstream of the straight section. This paper describes the coordinate system transformation necessary to properly model the magnet from field maps. The main field is checked by tracking the injected beam backwards, while leakage fields are included in dynamic aperture simulation and beam lifetime calculation. Simulation results show that the magnet design satisfies the physics requirement.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-MOPLM10
About •	paper received ※ 28 August 2019 paper accepted ※ 31 August 2019 issue date ※ 08 October 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPLM12	Progress on the Injection Transport Line Design for the APS Upgrade	injection, simulation, extraction, booster	120
	A. Xiao, M. Borland ANL, Lemont, Illinois, USA
	Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. An on-axis vertical injection scheme was adopted for the Advanced Photon Source upgrade multi-bend achromat lattice. As the design of the injection scheme has become more detailed, the booster to storage ring transport line (BTS) has advanced, including effects such as the septum field map and stray fields of storage ring magnets. Various error effects are simulated for setting specifications and predicting expected performance. The beam diagnostic scheme, including emittance measurement, is incorporated into the beamline design.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-MOPLM12
About •	paper received ※ 28 August 2019 paper accepted ※ 31 August 2019 issue date ※ 08 October 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPLO01	A Beam Spreader System for LCLS-II	kicker, undulator, FEL, electron	236
	T.G. Beukers, J.W. Amann, Y.M. Nosochkov SLAC, Menlo Park, California, USA
	For the LCLS-II project, the SLAC National Accelerator Laboratory is installing a new superconducting RF linac capable of continuously delivering 4 GeV electron bunches spaced 1.1 microseconds apart. A spreader system is required to distribute the beam between a soft X-ray or hard X-ray undulator, and a beam dump. An additional beam diverter is required in the front end of the linac to divert 100 MeV electrons to a diagnostic line. Both the spreader and diagnostic diversion systems are designed to operate on a bunch by bunch basis via the combination of fast kickers and a Lambertson septum. This paper presents a summary of the optics, kicker, and septum design. Of specific interest is the unique challenge associated with building a high repetition, high stability, spreader capable of diverting a single bunch without disturbing neighboring bunches. Additional discussion includes the application of the spreader technology to the proposed DASEL/S30XL beamline. This beamline will acceptμbunches evenly spaced between the undulator bound bunches, thus requiring a kicker with the same repetition rate as LCLS-II but a pulse width extended to approximately 600 ns.
	Poster MOPLO01 [1.256 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-MOPLO01
About •	paper received ※ 27 August 2019 paper accepted ※ 31 August 2019 issue date ※ 08 October 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Other Keywords

Page

MOPLM01

Alternative Injection Schemes to the NSLS-II Using Nonlinear Injection Magnets

injection, kicker, storage-ring, multipole

91

R.P. Fliller, III, G. Bassi, A. Blednykh, C. Hetzel, V.V. Smaluk, C.J. Spataro, P. Zuhoski
BNL, Upton, New York, USA

Funding: This manuscript has been authored by Brookhaven Science Associates, LLC under Contract No. DE-SC0012704 with the U.S. Department of Energy
The NSLS-II storage ring uses the standard four bump injection scheme to inject beam off axis. BESSY and MAX IV are now using a pulsed multipole magnet as an injection kicker. The injected beam sees a field off axis for injection while the stored beam experiences no field on the magnet axis. The principle advantage of using a pulsed multipole for injection is that the stored beam motion is greatly reduced since the field on axis is negligible. The number of pulsed magnets is reduced from five in the nominal scheme (septum and four bumps) to two or three thereby reducing the possible failure modes. This also eliminates the need to precisely match the pulse shapes of four dipole magnets to achieve minimal stored beam motion outside of the bump. In this paper we discuss two schemes of injecting into the NSLS-II using a pulsed multipole magnet. The first scheme uses a single pulsed multipole located in one cell downstream of the injection septum as the injection kicker. The second scheme uses two pulsed multipoles in the injection straight to perform the injection. We discuss both methods of injection and compare each method.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-MOPLM01

About •

paper received ※ 27 August 2019 paper accepted ※ 05 September 2019 issue date ※ 08 October 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPLM10

Simulation Study With Septum Field Map for the APS Upgrade

simulation, magnet-design, injection, photon

116

A. Xiao, M. Abliz, M. Borland
ANL, Lemont, Illinois, USA

Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357.
One of the biggest challenges faced by the Advanced Photon Source Upgrade injection system design is the septum magnet. Not only does the required leakage field inside the stored beam chamber need to be smaller than for the present ring, the magnet has to be slightly tilted about the z-axis to provide a gentle vertical bend that brings the injected beam trajectory close to y=0 when it passes through the storage ring quadrupole magnets upstream of the straight section. This paper describes the coordinate system transformation necessary to properly model the magnet from field maps. The main field is checked by tracking the injected beam backwards, while leakage fields are included in dynamic aperture simulation and beam lifetime calculation. Simulation results show that the magnet design satisfies the physics requirement.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-MOPLM10

About •

paper received ※ 28 August 2019 paper accepted ※ 31 August 2019 issue date ※ 08 October 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPLM12

Progress on the Injection Transport Line Design for the APS Upgrade

injection, simulation, extraction, booster

120

A. Xiao, M. Borland
ANL, Lemont, Illinois, USA

Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357.
An on-axis vertical injection scheme was adopted for the Advanced Photon Source upgrade multi-bend achromat lattice. As the design of the injection scheme has become more detailed, the booster to storage ring transport line (BTS) has advanced, including effects such as the septum field map and stray fields of storage ring magnets. Various error effects are simulated for setting specifications and predicting expected performance. The beam diagnostic scheme, including emittance measurement, is incorporated into the beamline design.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-MOPLM12

About •

paper received ※ 28 August 2019 paper accepted ※ 31 August 2019 issue date ※ 08 October 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPLO01

A Beam Spreader System for LCLS-II

kicker, undulator, FEL, electron

236

T.G. Beukers, J.W. Amann, Y.M. Nosochkov
SLAC, Menlo Park, California, USA

For the LCLS-II project, the SLAC National Accelerator Laboratory is installing a new superconducting RF linac capable of continuously delivering 4 GeV electron bunches spaced 1.1 microseconds apart. A spreader system is required to distribute the beam between a soft X-ray or hard X-ray undulator, and a beam dump. An additional beam diverter is required in the front end of the linac to divert 100 MeV electrons to a diagnostic line. Both the spreader and diagnostic diversion systems are designed to operate on a bunch by bunch basis via the combination of fast kickers and a Lambertson septum. This paper presents a summary of the optics, kicker, and septum design. Of specific interest is the unique challenge associated with building a high repetition, high stability, spreader capable of diverting a single bunch without disturbing neighboring bunches. Additional discussion includes the application of the spreader technology to the proposed DASEL/S30XL beamline. This beamline will acceptμbunches evenly spaced between the undulator bound bunches, thus requiring a kicker with the same repetition rate as LCLS-II but a pulse width extended to approximately 600 ns.

Poster MOPLO01 [1.256 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-MOPLO01

About •

paper received ※ 27 August 2019 paper accepted ※ 31 August 2019 issue date ※ 08 October 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)