JLab, Newport News, Virginia, USA
Fermilab, Batavia, Illinois, USA
BNL, Upton, New York, USA
The central detector in the present EIC design includes a 4 m long solenoid with an integrated strength of up to 12 Tm. The electron beam passes on-axis through the solenoid, but the hadron beam has an angle of 25 mrad. Thus the solenoid couples horizontal and vertical betatron motion in both electron and hadron storage rings, and causes a vertical closed orbit excursion in the hadron ring. The solenoid also couples the transverse and longitudinal motions of both beams, when crab cavities are also considered. In this paper, we present schemes for closed orbit correction and coupling compensation at the IP, including crabbing.
BNL, Upton, New York, USA
JLab, Newport News, USA
SLAC, Menlo Park, California, USA
This paper presents an overview of the Interaction Region (IR) design for the planned Electron-Ion Collider (EIC) at Brookhaven National Laboratory. The IR is designed to meet the requirements of the nuclear physics community *. The IR design features a ±4.5 m free space for the detector; a forward spectrometer magnet is used for the detection of hadrons scattered under small angles. The hadrons are separated from the neutrons allowing detection of neutrons up to ±4 mrad. On the rear side, the electrons are separated from photons using a weak dipole magnet for the luminosity monitor and to detect scattered electrons (e-tagger). To avoid synchrotron radiation backgrounds in the detector no strong electron bending magnet is placed within 40 m upstream of the IP. The magnet apertures on the rear side are large enough to allow synchrotron radiation to pass through the magnets. The beam pipe has been optimized to reduce the impedance; the total power loss in the central vacuum chamber is expected to be less than 90 W. To reduce risk and cost the IR is designed to employ standard NbTi superconducting magnets, which are described in a separate paper.
* An Assessment of U.S.-Based Electron-Ion Collider Science. (2018). Washington, D.C.: National Academies Press. https://doi.org/10.17226/25171
BNL, Upton, New York, USA
JLab, Newport News, Virginia, USA
SLAC, Menlo Park, California, USA
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
Fermilab, Batavia, Illinois, USA
ODU, Norfolk, Virginia, USA
FRIB, East Lansing, Michigan, USA
The design of the electron-ion collider EIC to be constructed at Brookhaven National Laboratory has been continuously evolving towards a realistic and robust design that meets all the requirements set forth by the nuclear physics community in the White Paper. Over the past year activities have been focused on maturing the design, and on developing alternatives to mitigate risk. These include improvements of the interaction region design as well as modifications of the hadron ring vacuum system to accommodate the high average and peak beam currents. Beam dynamics studies have been performed to determine and optimize the dynamic aperture in the two collider rings and the beam-beam performance. We will present the EIC design with a focus on recent developments.
BNL, Upton, New York, USA
ODU, Norfolk, Virginia, USA
CERN, Geneva, Switzerland
Crab cavities are specialized RF devices designed for colliders targeting high luminosities. It is a straightforward solution to retrieve head-on collision with crossing angle existing to fast separate both beams after collision. The Electron Ion Collider (EIC) has a crossing angle of 25 mrad, and will use local crabbing to minimize the dynamic aperture requirement throughout the rings. The current crab cavity design for the EIC lacks axial symmetry. Therefore, their higher order components of the fundamental deflecting mode have a potential of affecting the long-term beam stability. We present here the multipole analysis and preliminary particle tracking results from the current crab cavity design.
Brookhaven National Laboratory (BNL), Electron-Ion Collider, Upton, New York, USA
BNL, Upton, New York, USA
A new high-luminosity Electron-Ion Collider (EIC) is being designed at Brookhaven National Laboratory (BNL). Stable operation of the electron beam at an average current of 2.5A within 1100 bunches with a 7mm bunch length is one of the challenging tasks in achieving an electron-proton luminosity of 1033-1034 cm-2 ses−1 range. Beam induced heating, short-range and long-range wakefield analysis is discussed for some of the vacuum components of the electron storage ring (ESR), the hadron storage ring (HSR), and the rapid cycling synchrotron (RCS) and as well as the impact of the collective effects on the beam stability.