IPAC2021 - List of Authors (Liu, R.H.)

Paper	Title	Page
MOPAB299	STRUCTURAL OPTIMIZATION DESIGN OF FARADAY CUP FOR BEAM COMMISSIONING OF CSNS	943
	A.X. Wang, L. Kang, M. Meng, J.L. Sun IHEP, Beijing, People’s Republic of China J.X. Chen, H.Y. He, L. Liu, R.H. Liu, X.J. Nie, C.J. Ning, R.Y. Qiu, G.Y. Wang, T. Yang, J.B. Yu, Y.J. Yu, J.S. Zhang, D.H. Zhu IHEP CSNS, Guangdong Province, People’s Republic of China
	Faraday cup is used to absorb and stop the beam during the two phases of beam commissioning, such as the front end (FE) system and the temporary line after the drift tube linac (DTL) at the Chinese Spallation Neutron Source (CSNS). According to the beam physical parameters, graphite is selected to stop the beam directly, and oxygen-free copper which is just behind the graphite as the thermal conductive material. By the analysis and comparison of the target type and cooling efficiency, the single slant target is adopted. The incident angle between the target surface and the beam is set as 10°, meanwhile a new waterfall type water-cooling structure with parallel tunnels is designed to improve the cooling efficiency. The finite element software ANSYS is used for thermal analysis of the model, by which the diameter and interval of water cooling tunnels are optimized. The faraday cup discussed in this paper is finally successfully installed in the beam commissioning line and went well.
	Poster MOPAB299 [1.113 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-MOPAB299
About •	paper received ※ 13 May 2021 paper accepted ※ 08 July 2021 issue date ※ 19 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAB397	Design of the Two-Layer Girder for Accelerating Tube	3636
	X.J. Nie, H.Y. He, L. Kang IHEP, Beijing, People’s Republic of China J.X. Chen, L. Liu, R.H. Liu, C.J. Ning, A.X. Wang, G.Y. Wang, Y.J. Yu, J.S. Zhang, D.H. Zhu IHEP CSNS, Guangdong Province, People’s Republic of China J.B. Yu DNSC, Dongguan, People’s Republic of China
	An accelerating tube is one kind of important acceleration equipment of a linear accelerator. It is often made up of oxygen-free copper with a long tubular structure. It’s easy to suffer from deformation. Based on support requirements, the reasonable structure of the girder was obtained. Four supporting blocks were installed on the top surface of aluminum profile with the uniform distribution along the beam direction. The support strength with static condition and different working conditions were checked by ANSYS simulation calculation to ensure the stable operation of the girder. The two-layer girder can be used as a reference for other similar slender part for its simple structure and reliable support.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-WEPAB397
About •	paper received ※ 14 May 2021 paper accepted ※ 01 September 2021 issue date ※ 22 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAB282	Optimization Design of Four-Point Vibration Isolation Support for Spallation Neutron Source Vibration Magnet	4352
	J.S. Zhang, J.X. Chen, H.Y. He, L. Liu, R.H. Liu, C.J. Ning, G.Y. Wang, A.X. Wang, J.B. Yu, Y.J. Yu, D.H. Zhu IHEP CSNS, Guangdong Province, People’s Republic of China L. Kang IHEP, Beijing, People’s Republic of China
	Chinese spallation neutron source (CSNS) RCS of the dipole magnets by 25 Hz sinusoidal alternating current (AC) with dc bias field, because the magnet will produce eddy current effect caused by the vibration, this safe and reliable operation of the long-term impact of magnets, so need to CSNS/RCS dipole magnets, a support system for dynamic characteristic research and the performance of vibration isolation design. The mechanical model of ac dipole magnet and support system is first established, and ANSYS theoretical modal analysis and experimental modal verification are carried out. On this basis, vibration isolation parameters of the four-point support system are studied. The theoretical analysis and the experimental results of modal parameters are consistent, which shows that the ANSYS analysis model is correct and reliable. The dynamic system parameter design method established in this paper can be applied to various equipment of AC power accelerator. The final experimental verification shows that the total displacement amplitude of the isolator to the Y direction of the magnet on the magnetic support decreases by 62.3%.
	Poster THPAB282 [0.426 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-THPAB282
About •	paper received ※ 16 May 2021 paper accepted ※ 02 September 2021 issue date ※ 27 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAB300	Structure Design and Motion Analysis of 6-DOF Sample Positioning Platform	4387
	G.Y. Wang, J.X. Chen, L. Liu, R.H. Liu, C.J. Ning, A.X. Wang, J.B. Yu, Y.J. Yu, J.S. Zhang IHEP CSNS, Guangdong Province, People’s Republic of China L. Kang IHEP, Beijing, People’s Republic of China
	with the development of synchrotron radiation (SR) light source technology, in order to meet the requirements of sample positioning platform of some beamline stations, such as adjusting resolution at the nanometer level and having larger sample scanning distance, a six degree of freedom positioning platform based on spacefab structure was developed. The key technologies such as coordinate parameter transformation, kinematics analysis, and adjustment decoupling algorithm of 6-DOF pose adjustment system of SpaceFAB positioning platform are mainly studied. A 6-DOF platform driven by a stepping motor is designed and manufactured. The control system of the 6-DOF Platform Based on bus control is developed, and the adjustment accuracy is tested. The repeated positioning accuracy of the platform in three directions is 0.019 mm, and that of rotation is 0.011 ° in three directions. The test results verify the correctness of the theoretical analysis of SpaceFAB structure and the rationality of mechanism design. The research on the platform motion algorithm and control system has important reference value for the follow-up research of large stroke nano-6-dof positioning platform.
	Poster THPAB300 [1.517 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-THPAB300
About •	paper received ※ 16 May 2021 paper accepted ※ 06 July 2021 issue date ※ 02 September 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

STRUCTURAL OPTIMIZATION DESIGN OF FARADAY CUP FOR BEAM COMMISSIONING OF CSNS

943

A.X. Wang, L. Kang, M. Meng, J.L. Sun
IHEP, Beijing, People’s Republic of China
J.X. Chen, H.Y. He, L. Liu, R.H. Liu, X.J. Nie, C.J. Ning, R.Y. Qiu, G.Y. Wang, T. Yang, J.B. Yu, Y.J. Yu, J.S. Zhang, D.H. Zhu
IHEP CSNS, Guangdong Province, People’s Republic of China

Faraday cup is used to absorb and stop the beam during the two phases of beam commissioning, such as the front end (FE) system and the temporary line after the drift tube linac (DTL) at the Chinese Spallation Neutron Source (CSNS). According to the beam physical parameters, graphite is selected to stop the beam directly, and oxygen-free copper which is just behind the graphite as the thermal conductive material. By the analysis and comparison of the target type and cooling efficiency, the single slant target is adopted. The incident angle between the target surface and the beam is set as 10°, meanwhile a new waterfall type water-cooling structure with parallel tunnels is designed to improve the cooling efficiency. The finite element software ANSYS is used for thermal analysis of the model, by which the diameter and interval of water cooling tunnels are optimized. The faraday cup discussed in this paper is finally successfully installed in the beam commissioning line and went well.

Poster MOPAB299 [1.113 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-MOPAB299

About •

paper received ※ 13 May 2021 paper accepted ※ 08 July 2021 issue date ※ 19 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAB397

Design of the Two-Layer Girder for Accelerating Tube

3636

X.J. Nie, H.Y. He, L. Kang
IHEP, Beijing, People’s Republic of China
J.X. Chen, L. Liu, R.H. Liu, C.J. Ning, A.X. Wang, G.Y. Wang, Y.J. Yu, J.S. Zhang, D.H. Zhu
IHEP CSNS, Guangdong Province, People’s Republic of China
J.B. Yu
DNSC, Dongguan, People’s Republic of China

An accelerating tube is one kind of important acceleration equipment of a linear accelerator. It is often made up of oxygen-free copper with a long tubular structure. It’s easy to suffer from deformation. Based on support requirements, the reasonable structure of the girder was obtained. Four supporting blocks were installed on the top surface of aluminum profile with the uniform distribution along the beam direction. The support strength with static condition and different working conditions were checked by ANSYS simulation calculation to ensure the stable operation of the girder. The two-layer girder can be used as a reference for other similar slender part for its simple structure and reliable support.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-WEPAB397

About •

paper received ※ 14 May 2021 paper accepted ※ 01 September 2021 issue date ※ 22 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAB282

Optimization Design of Four-Point Vibration Isolation Support for Spallation Neutron Source Vibration Magnet

4352

J.S. Zhang, J.X. Chen, H.Y. He, L. Liu, R.H. Liu, C.J. Ning, G.Y. Wang, A.X. Wang, J.B. Yu, Y.J. Yu, D.H. Zhu
IHEP CSNS, Guangdong Province, People’s Republic of China
L. Kang
IHEP, Beijing, People’s Republic of China

Chinese spallation neutron source (CSNS) RCS of the dipole magnets by 25 Hz sinusoidal alternating current (AC) with dc bias field, because the magnet will produce eddy current effect caused by the vibration, this safe and reliable operation of the long-term impact of magnets, so need to CSNS/RCS dipole magnets, a support system for dynamic characteristic research and the performance of vibration isolation design. The mechanical model of ac dipole magnet and support system is first established, and ANSYS theoretical modal analysis and experimental modal verification are carried out. On this basis, vibration isolation parameters of the four-point support system are studied. The theoretical analysis and the experimental results of modal parameters are consistent, which shows that the ANSYS analysis model is correct and reliable. The dynamic system parameter design method established in this paper can be applied to various equipment of AC power accelerator. The final experimental verification shows that the total displacement amplitude of the isolator to the Y direction of the magnet on the magnetic support decreases by 62.3%.

Poster THPAB282 [0.426 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-THPAB282

About •

paper received ※ 16 May 2021 paper accepted ※ 02 September 2021 issue date ※ 27 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAB300

Structure Design and Motion Analysis of 6-DOF Sample Positioning Platform

4387

G.Y. Wang, J.X. Chen, L. Liu, R.H. Liu, C.J. Ning, A.X. Wang, J.B. Yu, Y.J. Yu, J.S. Zhang
IHEP CSNS, Guangdong Province, People’s Republic of China
L. Kang
IHEP, Beijing, People’s Republic of China

with the development of synchrotron radiation (SR) light source technology, in order to meet the requirements of sample positioning platform of some beamline stations, such as adjusting resolution at the nanometer level and having larger sample scanning distance, a six degree of freedom positioning platform based on spacefab structure was developed. The key technologies such as coordinate parameter transformation, kinematics analysis, and adjustment decoupling algorithm of 6-DOF pose adjustment system of SpaceFAB positioning platform are mainly studied. A 6-DOF platform driven by a stepping motor is designed and manufactured. The control system of the 6-DOF Platform Based on bus control is developed, and the adjustment accuracy is tested. The repeated positioning accuracy of the platform in three directions is 0.019 mm, and that of rotation is 0.011 ° in three directions. The test results verify the correctness of the theoretical analysis of SpaceFAB structure and the rationality of mechanism design. The research on the platform motion algorithm and control system has important reference value for the follow-up research of large stroke nano-6-dof positioning platform.

Poster THPAB300 [1.517 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-THPAB300

About •

paper received ※ 16 May 2021 paper accepted ※ 06 July 2021 issue date ※ 02 September 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)