IPAC2016 - List of Authors (Singh, O.)

Paper	Title	Page
MOPMR057	Measurements using Button BPM SUM Signal	377
	W.X. Cheng, K. Ha, J. Mead, O. Singh, G.M. Wang BNL, Upton, Long Island, New York, USA
	Modern digital BPM detectors measure not only the beam positions, four buttons SUM signal can be very helpful for machine developments and operations. At NSLS-II, BPM SUM signal has been used from commissioning stage, to investigate localized beam losses. During top-off operation, precise beam lifetime measurement within relative short period of time becomes important. With many BPMs along the ring, BPM SUM can be a much more accurate tool to measure the beam current and lifetime. BPM SUM signal shall be proportional to beam current, and it may depends on button sizes and BPM chamber geometry, cable attenuations, electronics attenuations, beam position, bunch lengths, fill pattern etc. Experience of BPM SUM signals measurements will be presented.
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-MOPMR057
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPOR033	Experimental Study of Single Bunch Instabilities at NSLS-II Storage Ring	1738
	W.X. Cheng, B. Bacha, G. Bassi, A. Blednykh, B. Podobedov, O. Singh, V. Smalyuk BNL, Upton, New York, USA
	Single bunch instabilities have been observed since the early stage of NSLS-II storage ring commissioning. After installing the super-conducting cavity, the single bunch instability threshold current was similar at 0.7mA. The instability was eventually determined to be due to transverse mode coupling. Microwave instability has been characterized using streak camera bunch profile, horizontal beam sizes at dispersion location and beam spectrums. Microwave instability threshold current dependency on bunch lengths and IUV gaps has been studied. Most recent experimental results will be presented in this paper.
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-TUPOR033
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEOBB01	Single Micron Single-Bunch Turn-by-Turn BPM Resolution Achieved at NSLS-II	2095
	B. Podobedov, W.X. Cheng, K. Ha, Y. Hidaka, J. Mead, O. Singh, K. Vetter BNL, Upton, Long Island, New York, USA
	NSLS-II state-of-the-art BPMs provide a single micron turn-by-turn BPM resolution for any bunch train of reasonable intensity. For certain beam dynamics studies a similar, or even better, resolution is desired for a single-, or a few-bunch fill, which is not yet available with our standard BPM signal processing. This paper describes our experience with more advanced BPM ADC signal processing which allowed us to significantly improve turn-by-turn BPM resolution in single bunch mode down to the level of about one micron at ~1 nC/bunch. We also present the examples of machine studies that benefit from this BPM performance enhancement.
	Slides WEOBB01 [2.565 MB]
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-WEOBB01
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPOW059	The NSLS-II Top Off Safety System	2985
	R.P. Fliller, D. Bergman, A. Caracappa, L. Doom, G. Ganetis, Y. Hu, Y. Li, W. Louie, D. Padrazo, O. Singh, J. Tagger, G.M. Wang, Z. Xia BNL, Upton, Long Island, New York, USA
	Funding: This manuscript has been authored by Brookhaven Science Associates, LLC under Contract No. DE-SC0012704 with the U.S. Department of Energy. Top Off operation is the desired mode of operation for 3rd generation light sources to ensure beam current stability for user experiments. However, top off operation introduces the hazard of injecting electrons into the front ends with the beamline shutters open. This hazard can be mitigated with the appropriate safety system. This past year, the NSLS-II has transitioned from decay mode to top off operation with the introduction of the Top Off Safety System (TOSS). Top Off was initially demonstrated September 22, 2015 and become standard mode of operating. In this paper we discuss the top off safety system, operation with the system, and future directions.
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-WEPOW059
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPOY048	NSLS-II Active Interlock System and Post-Mortem Architecture	4214
	K. Ha, E.B. Blum, W.X. Cheng, J. Choi, Y. Hu, D. Padrazo, S. Seletskiy, O. Singh, R.M. Smith, J. Tagger, Y. Tian, G. Wang, T. Yang BNL, Upton, Long Island, New York, USA
	The NSLS-II at Brookhaven National Laboratory (BNL) started the user beam service in early 2015, and is currently operating 13 of the insertion device (ID) and beamlines as well as constructing new beamlines. The fast machine protection consists of an active interlock system (AIS), beam position monitor (BPM), cell controller (CCs) and front-end (FE) systems. The AIS measures the electron beam envelop and the dumps the beam by turning off RF system, and then the diagnostic system provides the post-mortem data for an analysis of which system caused the beam dump and the machine status analysis. NSLS-II post-mortem system involves AIS, CCs, BPMs, radio frequency system (RFs), power supply systems (PSs) as well as the timing system. This paper describes the AIS architecture and PM performance for NSLS-II safe operations.
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-THPOY048
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Measurements using Button BPM SUM Signal

377

W.X. Cheng, K. Ha, J. Mead, O. Singh, G.M. Wang
BNL, Upton, Long Island, New York, USA

Modern digital BPM detectors measure not only the beam positions, four buttons SUM signal can be very helpful for machine developments and operations. At NSLS-II, BPM SUM signal has been used from commissioning stage, to investigate localized beam losses. During top-off operation, precise beam lifetime measurement within relative short period of time becomes important. With many BPMs along the ring, BPM SUM can be a much more accurate tool to measure the beam current and lifetime. BPM SUM signal shall be proportional to beam current, and it may depends on button sizes and BPM chamber geometry, cable attenuations, electronics attenuations, beam position, bunch lengths, fill pattern etc. Experience of BPM SUM signals measurements will be presented.

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-MOPMR057

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPOR033

Experimental Study of Single Bunch Instabilities at NSLS-II Storage Ring

1738

W.X. Cheng, B. Bacha, G. Bassi, A. Blednykh, B. Podobedov, O. Singh, V. Smalyuk
BNL, Upton, New York, USA

Single bunch instabilities have been observed since the early stage of NSLS-II storage ring commissioning. After installing the super-conducting cavity, the single bunch instability threshold current was similar at 0.7mA. The instability was eventually determined to be due to transverse mode coupling. Microwave instability has been characterized using streak camera bunch profile, horizontal beam sizes at dispersion location and beam spectrums. Microwave instability threshold current dependency on bunch lengths and IUV gaps has been studied. Most recent experimental results will be presented in this paper.

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-TUPOR033

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEOBB01

Single Micron Single-Bunch Turn-by-Turn BPM Resolution Achieved at NSLS-II

2095

B. Podobedov, W.X. Cheng, K. Ha, Y. Hidaka, J. Mead, O. Singh, K. Vetter
BNL, Upton, Long Island, New York, USA

NSLS-II state-of-the-art BPMs provide a single micron turn-by-turn BPM resolution for any bunch train of reasonable intensity. For certain beam dynamics studies a similar, or even better, resolution is desired for a single-, or a few-bunch fill, which is not yet available with our standard BPM signal processing. This paper describes our experience with more advanced BPM ADC signal processing which allowed us to significantly improve turn-by-turn BPM resolution in single bunch mode down to the level of about one micron at ~1 nC/bunch. We also present the examples of machine studies that benefit from this BPM performance enhancement.

Slides WEOBB01 [2.565 MB]

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-WEOBB01

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPOW059

The NSLS-II Top Off Safety System

2985

R.P. Fliller, D. Bergman, A. Caracappa, L. Doom, G. Ganetis, Y. Hu, Y. Li, W. Louie, D. Padrazo, O. Singh, J. Tagger, G.M. Wang, Z. Xia
BNL, Upton, Long Island, New York, USA

Funding: This manuscript has been authored by Brookhaven Science Associates, LLC under Contract No. DE-SC0012704 with the U.S. Department of Energy.
Top Off operation is the desired mode of operation for 3rd generation light sources to ensure beam current stability for user experiments. However, top off operation introduces the hazard of injecting electrons into the front ends with the beamline shutters open. This hazard can be mitigated with the appropriate safety system. This past year, the NSLS-II has transitioned from decay mode to top off operation with the introduction of the Top Off Safety System (TOSS). Top Off was initially demonstrated September 22, 2015 and become standard mode of operating. In this paper we discuss the top off safety system, operation with the system, and future directions.

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-WEPOW059

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPOY048

NSLS-II Active Interlock System and Post-Mortem Architecture

4214

K. Ha, E.B. Blum, W.X. Cheng, J. Choi, Y. Hu, D. Padrazo, S. Seletskiy, O. Singh, R.M. Smith, J. Tagger, Y. Tian, G. Wang, T. Yang
BNL, Upton, Long Island, New York, USA

The NSLS-II at Brookhaven National Laboratory (BNL) started the user beam service in early 2015, and is currently operating 13 of the insertion device (ID) and beamlines as well as constructing new beamlines. The fast machine protection consists of an active interlock system (AIS), beam position monitor (BPM), cell controller (CCs) and front-end (FE) systems. The AIS measures the electron beam envelop and the dumps the beam by turning off RF system, and then the diagnostic system provides the post-mortem data for an analysis of which system caused the beam dump and the machine status analysis. NSLS-II post-mortem system involves AIS, CCs, BPMs, radio frequency system (RFs), power supply systems (PSs) as well as the timing system. This paper describes the AIS architecture and PM performance for NSLS-II safe operations.

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-THPOY048

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)