Keyword: brilliance
Paper Title Other Keywords Page
MOPEA026 X-ray Powder Diffraction Beamline for the Iranian Light Source Facility photon, electron, synchrotron, focusing 130
 
  • H. Khosroabadi, S. Amiri, H. Ghasem, A. Gholampour
    ILSF, Tehran, Iran
  • H. Ghasem
    IPM, Tehran, Iran
 
  Iranian Light Source Facility (ILSF) project has been initiated since 2010 in order to design and construction of a synchrotron facility in Iran. In parallel with the machine’s activities, scientific committee, users community and beamline technical group are working on different aspects of the scientific and beamline design issues for the operating phase after construction*. X-ray powder diffraction beamline is one of the most priorities in ILSF due to wide range of applications and big potential user community in Iran. Conceptual design report of this beamline operating in other worldwide synchrotrons have been studied and compared in details. The light source and schematic design of the beamline has been prepared in this study. Then, the parameters have been calculated and have been optimized by employing computational software such as XOP and SHADOW**. The optical properties of the optical elements such as reflectivity, absorbance, Bragg diffraction, rocking curve, aberration, etc have been studied at this design, and the results have been compared with the other published results. The outcome and final results of this design progress will be discussed in details.
References:
* Conceptual Design Report (2011, summer), ILSF, http://ilsf.ipm.ac.ir/.
** http://www.esrf.eu/UsersAndScience/Experiments/TBS/SciSoft/xop2.3.
 
 
MOPME043 Calibration of Beam Position Monitors in the Injector of HLS II quadrupole, coupling, linac, emittance 568
 
  • J.Y. Zou, J. Fang, W.B. Li, P. Lu, T.J. Ma, B.G. Sun, Y.L. Yang, Z.R. Zhou
    USTC/NSRL, Hefei, Anhui, People's Republic of China
 
  Funding: Supported by the National Science Foundation of China (11175173, 11105141)
A beam position monitor(BPM) system is being installed to improve the beam position measurement of the injector at the upgrade project of Hefei Light Source (HLS II). The new BPM system is consists of 19 stripline BPMs and 19 Libera Brilliance Single Pass modules. Before installation, the response of the BPMs must be mapped to improve the accuracy of measurement. The theoretical equations of both position and quadrupole component of the BPM are calculated first, using both formula and matlab simulation. A laboratory calibration system is built. The inconsistency of Libera Brilliance Single Pass channels is measured to improve the accuracy of calibration. The calibrating results show the position sensitivity is less than 5% difference compare to the theoretical value, while the quadrupole component sensitivity is less than 10% difference.
 
 
TUOAB203 ESRF Upgrade Phase II lattice, emittance, storage-ring, vacuum 1140
 
  • J.-L. Revol, P. Berkvens, J.C. Biasci, J-F. B. Bouteille, N. Carmignani, F. Ewald, L. Farvacque, A. Franchi, L. Goirand, M. Hahn, L. Hardy, J. Jacob, J.M. Koch, G. Lebec, S.M. Liuzzo, B. Nash, T.P. Perron, E. Plouviez, P. Raimondi, K.B. Scheidt, V. Serrière
    ESRF, Grenoble, France
 
  Four years after the launch of the Upgrade Programme, the ESRF is midway through its first phase (2009-2015) and has defined the objectives for the ensuing second phase. The first phase paved the way to a new generation of nano-beam X-ray beamlines fed by an X-ray source itself substantially improved in terms of reliability, stability and brilliance. The second phase envisions a major upgrade of the source to best serve the science case of this new generation of beamlines. In December 2012, the ESRF Council endorsed Management's proposal to launch the technical design study of a new 7-bend achromat lattice. This new configuration will allow the ESRF storage ring to operate with a decrease in horizontal emittance by a factor of about 30 and a consequent increase in brilliance and coherence of the photon beam. The increase will be substantially higher at X-ray energies larger than 50 keV.  
slides icon Slides TUOAB203 [3.664 MB]  
 
WEPWA030 Using the Power Spectral Density Method to Characterize and Evaluate the X-ray Mirrors Surfaces synchrotron, simulation, focusing, optics 2196
 
  • W.Q. Hua, F.G. Bian, Y.M. He, W.H. Lin, L. Song, J. Wang, N. Zhao
    SINAP, Shanghai, People's Republic of China
 
  Rapid progress in synchrotron X-ray beams’ coherence and X-ray optics performance places a high demand on characterization and evaluation of optical surface figure and slope errors and roughness on meter-long optics over spatial frequencies as short as 0.1mm. In this paper, the propagation model of hard X-ray beams through reflecting mirror surface is proposed based on wave-front propagation, and numerical simulations are performed for predicting the hard X-ray focusing performance of different imperfect mirrors using a Fresnel diffraction calculation. The imperfect mirror surface height maps synthesized from power spectral functions are used to analyze and evaluate the influences of different mirror surface errors on the reflected hard X-ray beam properties.  
 
WEPME037 Fast Orbit Feedback at Taiwan Photon Source controls, feedback, EPICS, storage-ring 3007
 
  • A. Bardorfer, P. Leban
    I-Tech, Solkan, Slovenia
  • P.C. Chiu, K.T. Hsu, C.H. Kuo
    NSRRC, Hsinchu, Taiwan
 
  Low latency, distributed, Fast Orbit Feedback (FOFB) application, based on singular value decomposition, entirely implemented in FPGA, has been developed for the Taiwan Photos Source (TPS). The FOFB utilizes the latest Libera Brilliance+ units for measuring beam position and the Gigabit Data eXchange (GDX) modules, which take care of global orbit distribution via 6.5 Gbit/s fiber optic or passive Cu links, and provide a large orbit data history buffer. The magnet correction in a matrix form of M = V . PI( S-1 . UT . ( Golden-Orbit ) ) is calculated entirely in FPGA, using a massively parallel approach and sent to the magnet power supplies via 2.5 Gbit/s link. The entire FOFB calculation is distributed over 48 GDX modules and the system allows for synchronous (on/off/pause) FOFB control via external input signal. The latencies of 60 ns per BPM for orbit distribution, 1.5 us for FOFB calculation and 1.5 us for magnet data transmission have been measured at TPS test installation in November 2012. The expected total communication and FOFB calculation latency in the TPS final configuration (168 BPMs) is expected to stay within 15-20 us range.