| Paper | Title | Other Keywords | Page |
|---|---|---|---|
| MOPO001 | Interaction Point Feedback Design and Integrated Simulations to Stabilize the CLIC Final Focus* | controls, simulation, feedback, quadrupole | 475 |
|
|||
| The Compact Linear Collider (CLIC) accelerator has strong precision requirements on offset position between the beams. The beam which is sensitive to ground motion needs to be stabilized to unprecedented requirements. Different Beam Based Feedback (BBF) algorithms such as Orbit Feedback (OFB) and Beam-Beam Offset Feedback (BBOF) have been designed. This paper focuses on the BBOF control which could be added to the CLIC baseline. It has been tested for different ground motion models in the presence of noises or disturbances and uses digital linear control with or without an adaptive loop. The simulations demonstrate that it is possible to achieve the required performances and quantify the maximum allowed noise level. This amount of admitted noises and disturbances is given in terms of an equivalent disturbance on the position of the magnet that controls the beam offset. Due to the limited sampling frequency of the process, the control loop is in a very small bandwidth. The study shows that these disturbances have to be lowered by other means in the higher frequency range. | |||
| MOPO014 | SVD-based Filter Design for the Trajectory Feedback of CLIC | feedback, luminosity, controls, simulation | 511 |
|
|||
| The orbit feedback of the Compact Linear Collider (CLIC) is the basic counter-measure against ground motion effects below 1 Hz in the beam delivery system and the main linac of CLIC. In this paper we present significant improvements of the orbit feedback design, by using time-dependent and spatial filters. The design procedure is based on a singular value decomposition (SVD) of the orbit response matrix and on loop-shaping techniques. This modified design has essential advantages compared to previous ones. The required beam position monitor resolution in the beam delivery system could be relaxed by a factor of five. At the same time the suppression of ground motion effects is improved. As a consequence, the tight tolerances for the allowable luminosity loss due to ground motion effects in CLIC can be met. The presented methods can be easily adapted to other accelerators in order to relax sensor tolerances and to efficiently suppress ground motion effects. | |||
| MOPO028 | Modal Analysis and Measurement of Water Cooling Induced Vibrations on a CLIC Main Beam Quadrupole Prototype* | quadrupole, resonance, controls, damping | 541 |
|
|||
|
Funding: The research leading to these results has received funding from the European Commission under the FP7 Research Infrastructures project EuCARD, grant agreement no. 227579. To reach the Compact Linear Collider (CLIC) design luminosity, the mechanical jitter of the CLIC main beam quadrupoles should be smaller than 1.5 nm integrated root mean square (r.m.s.) displacement above 1 Hz. A stiff stabilization and nano-positioning system is being developed but the design and effectiveness of such a system will greatly depend on the stiffness of the quadrupole magnet which should be as high as possible. Modal vibration measurements were therefore performed on a first assembled prototype magnet to evaluate the different mechanical modes and their frequencies. The results were then compared with a Finite Element (FE) model. The vibrations induced by water-cooling without stabilization were measured with different flow rates. This paper describes and analyzes the measurement results. |
|||
| TUPC014 | System Control for the CLIC Main Beam Quadrupole Stabilization and Nano-positioning* | feedback, quadrupole, luminosity, simulation | 1021 |
|
|||
| The conceptual design of the active stabilization and nano-positioning of the CLIC main beam quadrupoles was validated in models and experimentally demonstrated on test benches. Although the mechanical vibrations were reduced to within the specification of 1.5 nm at 1 Hz, additional input for the stabilization system control was received from integrated luminosity simulations that included the measured stabilization transfer functions. Studies are ongoing to obtain a transfer function which is more compatible with beam based orbit feedback; it concerns the controller layout, new sensors and their combination. In addition, the gain margin must be increased in order to reach the requirements from a higher vibration background. For this purpose, the mechanical support is adapted to raise the frequency of some resonances in the system and the implementation of force sensors is considered. Furthermore, this will increase the speed of repositioning the magnets between beam pulses. This paper describes the improvements and their implementation from a controls perspective. | |||
| TUPC023 | Status of Ground Motion Mitigation Techniques for CLIC | luminosity, feedback, quadrupole, simulation | 1048 |
|
|||
| The Compact Linear Collider (CLIC) accelerator has strong stability requirements on the position of the beam. In particular, the beam position will be sensitive to ground motion. A number of mitigation techniques are proposed - quadrupole stabilisation and positioning, final doublet stabilisation as well as beam based orbit and interaction point (IP) feedback. Integrated studies of the impact of the ground motion on the CLIC Main Linac (ML) and Beam Delivery System (BDS) have been performed, which model the hardware and beam performance in detail. Based on the results future improvements of the mitigation techniques are suggested and simulated. It is shown that with the current design the tight luminosity budget for ground motion effects is fulfilled and accordingly, an essential feasibility issue of CLIC has been addressed. | |||
| TUPZ041 | Site Studies for the SuperB Collider and Synchrotron Radiation Facility Project | site, collider, linac, injection | 1900 |
|
|||
| The SuperB project aims at the construction of a very high luminosity (1036 cm-2 s−1) asymmetric electron-positron collider. Due to its large beam current (~2 A) high energy (~7 GeV) and low vertical emittance (less than 10-11 m) the facility looks very attractive as an x-ray synchrotron radiation source, and therefore few beam lines are also foreseen. Possible locations are the campus of the University of Rome Tor Vergata or near another Italian INFN laboratory site. This paper presents and describes the status of the preliminary design of the civil infrastructure layout and related site issues. | |||