Paper | Title | Page |
---|---|---|
THPZ024 | Updated Design of the Italian SuperB Factory Injection System | 3738 |
|
||
The ultra high luminosity B-factory (SuperB) project of INFN requires a high performance and reliable injection system, providing electrons at 4 GeV and positrons at 7 GeV, to fulfill the very tight requirements of the collider. Due to the short beam lifetime, continuous injection of electrons and positrons in both HER and LER rings is necessary to keep the average luminosity at a high level. An updated version of the injection system, optimized at higher repetition frequency is presented. This scheme includes a polarized electron gun, a positron production scheme with electron/positron conversion at low energy 0.6 GeV, and a 1 GeV damping ring to reduce the injected emittance of the positron beam. | ||
THPZ003 | The SuperB Project: Accelerator Status and R&D | 3684 |
|
||
The SuperB collider project has been recently approved by the Italian Government as part of the National Research Plan. SuperB is a high luminosity (1036 cm-2 s-1) asymmetric e+e− collider at the Y(4S) energy. The design is based on a “large Piwinski angle and Crab Waist” scheme already successfully tested at the DAΦNE Phi-Factory in Frascati, Italy. The project combines the challenges of high luminosity colliders and state-of-the-art synchrotron light sources, with two beams (e+ at 6.7 and e- at 4.2 GeV) with extremely low emittances and small beam sizes at the Interaction Point. As unique features, the electron beam will be longitudinally polarized at the IP and the rings will be able to ramp down to collide at the tau/charm energy threshold with one tenth the luminosity. The relatively low beam currents (about 2 A) will allow for low running (power) costs compared to similar machines. The insertion of beam lines for synchrotron radiation users is the latest feature included in the design. The lattice has been recently modified to accommodate insertion devices for X-rays production. A status of the project and a description of R&D in progress will be presented. | ||
WEPS001 | A New Lattice for the Beta-beam Decay Ring to Reduce the Head Tail Effects | 2478 |
|
||
Funding: I acknowledge the financial support of the European Community under the European Commission Framework Programme 7 Design Study: EUROnu, Project Number 212372. The beta-beam concept relies on the production, by beta decay of radioactive ions of a very high flux, of an electron neutrino and anti-neutrino beam towards a distant detector. In this aim, the radioactive isotopes are stored in a long racetrack-shaped ring, called the decay ring, where they orbit until they decay or are lost. The intensities to store in the decay ring to obtain the required neutrino fluxes are very high (several amperes in average). Therefore, collective effects occur. Among them, the head tail effect, caused by transversal resonance impedance, is one of the main issues: the beam was shown to be unstable with the previous decay ring lattice. The transition gamma was reduced to mitigate this problem. For this purpose the lattice was changed by removing the injection from the arc to put it in a chicane which is added in one of the long straight sections. After presenting the limitation due to head tail effects, we will present the modification in the lattice and their impact on the dynamic aperture in the decay ring. Then the improvement on the beta-beam performance with respect to the lower transition gamma will be shown. |
||
WEPS002 | Limitations in Mitigating Collective Effects in the Beta-Beam Decay Ring by the Use of Octupoles | 2481 |
|
||
Funding: I acknowledge the financial support of the European Community under the European Commission Framework Programme 7 Design Study: EUROnu, Project Number 212372. The beta-beam concept relies on the production, by beta decay of radioactive ions of a very high flux, of an electron neutrino and anti-neutrino beam towards a distant detector. After production and acceleration in an accelerator complex consisting of a rapid cycling synchrotron, the CERN PS and the CERN SPS, the radioactive isotopes are injected into a long racetrack-shaped ring, called the decay ring, where they orbit until they decay or are lost. The required intensities to store in the decay ring to reach the aimed neutrino fluxes are very high. Among the collective effects, the head tail effect, caused by transversal resonance impedance, is one of the main issues: the beam was shown to be unstable with the previous decay ring lattice. The lattice was changed to handle this problem; e.g. octupoles were included to increase the stability limit with an amplitude detuning. We here report on the improvement on the beta-beam performance with respect to amplitude detuning in the decay ring and discuss other mitigation attempts. |
||
WEPS024 | Beta Beams: An Accelerator-based Facility to Explore Neutrino Oscillation Physics | 2535 |
|
||
Funding: This contribution is a project funded by European Community under the European Commission Framework Programme 7 Design Study: EUROnu, Project Number 212372. The recent discovery of neutrino oscillations, has implications for the Standard Model of particle physics (SM). Knowing the contribution of neutrinos to the SM, needs precise measurements of the parameters governing the neutrino oscillations. The EUROν Design Study will review three facilities (the so-called Super-Beams, Beta Beams and Neutrino Factories) and perform a cost assessment that, coupled with the physics performance, will give means to the European research authorities to make a decision on future European neutrino oscillation facility. "Beta Beams" produce collimated pure electron (anti-)neutrino by accelerating beta active ions to high energies and having them decay in a storage ring. EUROν Beta Beams are based on CERN’s infrastructure and existing machines. Using existing machines is an advantage for the cost evaluation, however, this choice is also constraining the Beta Beams. Recent work to make the Beta Beam facility a solid option will be described: production of Beta Beam isotopes, the 60 GHz pulsed ECR source development, integration into the LHC-upgrades, ensure the high intensity ion beam stability, and optimizations to get high neutrino fluxes. |
||