ORNL, Oak Ridge, Tennessee
Solid-state based high-power modulators utilize new technology, yet must meet the operational needs of a high reliability facility. This modulator technology is in use at SNS, and is under consideration and development for future machines, such as the ILC and PEFP. Through operational experience and a sustained development effort, a number of improvements have been deployed in the SNS modulator system to meet the high availability demands of operating facilities. The operating experience and development effort of the world-wide community will also be reviewed.
NSRRC, Hsinchu
The purpose of this paper is to reduce the Electromagnetic Interference (EMI) from kicker and its pulsed power supply. Analysis of conducted and radiated EMI is the beginning mission. Different frequency range of radiated EMI was measured by different sensors. A hybrid shielding method was used to test reduction of radiated EMI. The copper and μ-metal enclosure was used on kicker magnet to prevent the radiated EMI. The reduction of electromagnetic field showed the effect of different material. Besides, the conducted EMI was also tested and eliminated by adding grounding routs. For decreasing grounding noise to other systems, the individual grounding bus was installed. The experimental results showed significant effect. In the future, TPS (Taiwan Photon Source) injection magnets will design higher performance, lower EMI than TLS (Taiwan Light Source). Therefore reducing and eliminating the interference of electromagnetic waves will be a very important issue. All the EMI prevention schemes will implement in the new project.
BNL, Upton, Long Island, New York
Funding: Work supported by Brookhaven Science Associates, LLC underContract No. DE-AC02-98CH10886 with the U.S. Department of Energy.
In order to cross more rapidly the 82 weak resonances caused by the horizontal tune and the partial snakes, we plan to jump the horizontal tune 82 times during the acceleration cycle, 41 up and 41 down*. To achieve this, the magnets creating this tune jump will pulse on in 100 micro-seconds, hold the current flat for about four milli-seconds and zero the current in another 100 micro-seconds. The magnets are old laminated beam transport magnets with longitudinal shims closing the aperture to reduce inductance and power supply current. The power supply uses a high voltage capacitor discharge to raise the magnet current, which is then switched to a low voltage supply, and then the current is switched back to the high voltage capacitor to zero the current. The current in each of the magnet pulses must match the order of magnitude change in proton momentum during the acceleration cycle. The magnet, power supply and cabling will be described with coast saving features and operational experience.
*Overcome Horizontal Depolarizing Resonances in the AGS with Tune Jump
CIAE, Beijing
Department of Physics, Central China Normal University, Wuhan
Light II-A pulsed power generator was used as a power driver of pumping KrF laser at CIAE. The redesign of Light II-A pulsed power generator is based on the consideration that the machine will consist of one single Marx generator with two different experimental lines，which is presented in this paper. The original experimental line with characteristic impedance of 5Ω is remained, and a new line of low impedance (about 1.5Ω ) is added to the Marx generator. The structure design and the electric insulation design are introduced. It is also outlined here the manipulation of modeling the dynamic behavior of gas discharge arc as well as the circuit simulation results of the two experimental lines. Meanwhile a brief introduction is given to the potential application of the low impedance line.
CAEP/IFP, Mainyang, Sichuan
Funding: Hongtao Li is with the Institute of Fluid Physics, China Academy of Engineering Physics (CAEP), Mianyang City, Sichuan, China. (Fax:86-816-2282695; e-mail: lht680526@ 21cn.com).
In order to study the physics of fast Z-pinches and research the key issues of pulse power technology, a 10MA/6MV z-pinch primary test stand (PTS) composed of 24 modules will be built in IFP. The prototype module adopted capacitive storage scheme is composed of the 6MV/300kJ Marx-generator (MG), intermediate storage capacitor (IC), laser-triggered switch (LTS), pulse forming line (PFL), water self-breakdown switch (WS), and tri-plate pulse transmission line (PTL). The measured output current of the prototype is approximate 520kA, and output voltage is approximate 2.1MV. The unique multi-stage LTS based on uniform field distribution design and multi-pin unsymmetrical WS make the prototype modules have low systemic delay jitter which is necessary for synchronization of multi-module facility. 1-δ jitter of delay of the system is less than 4ns.
IHEP Beijing, Beijing
China Spallation Neutron Source is a high intensity beam facility planed to build in future in China. It is composed of Linac, RCS and target station. The beam extraction from the RCS will be realized by ten vertical kicker magnet and one Lambertson magnet. One prototype kicker magnet has been successfully designed and developed in Institute of High Energy Physics. In this paper, the physical and structural design of the prototype kicker magnet are presented, and issues of the magnet development, construction and test are discussed.
IHEP Beijing, Beijing
The prototype of pulsed power supply for injection painting bump magnets of CSNS/RCS is being developed. This pulsed power supply consists of IGBT H bridges in series and parallel. The pulse current of the prototype is 18000A, the voltage is about 3KV and the equivalent frequency is about 1MHz. This paper will introduce this prototype in detail.
IHEP Beijing, Beijing
China Spallation Neutron Source is a high intensity beam facility planed to build in future in China. It is composed of Linac, RCS and target station. Two sets of pulsed painting bump magnets, 4 magnets in each set , will be used in CSNS RCS to create a dynamic orbit bump for injection process. The design of these 8 bump magnets has been completed. One prototype bump magnet has been assembled and tested. In this paper, the magnetic field analysis, the eddy current and thermal consideration in the end plates of the prototype bump magnet are presented, and issues of the magnet development, construction and test are discussed.
DULY Research Inc., Rancho Palos Verdes, California
Marx modulators, operated by the solid-state switches of Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) or Insulated Gate Bipolar Transistors (IGBTs), offer an alternative to conventional high voltage modulators for rf power sources. They have the advantages of compact size, high-energy efficiency, high reliability, pulse width control and cost reduction. However, Marx modulators need a complex voltage compensation circuit if they are employed in long pulse applications such as the ILC project. We describe novel schemes to compensate the voltage droop of the Marx modulator and minimize the flattop fluctuation of the voltage pulse output through the utilization of inductances and the fast switching properties of solid-state switches. The feasibility of the schemes has been analyzed and relevant data will be presented.
Diversified Technologies, Inc., Bedford, Massachusetts
Funding: Funding by U.S. Department of Energy SBIR program.
Diversified Technologies, Inc. (DTI) has developed high power, solid-state Marx Bank modulators for a range of accelerators and colliders. We estimate the Marx topology can deliver equivalent performance to conventional designs, while reducing system costs by 25-50%. In this paper DTI will describe the application of Marx based technology to a long-pulse (140 kV, 160 A, 1.5 ms) modulator design focused on the International Linear Collider. The primary engineering challenge is minimizing the overall size and cost of the storage capacitors in the modulator. Unique choices in components and controls are needed, including the use of electrolytic capacitors. This paper will review recent progress in the development and testing of this long pulse Marx modulator built under a U.S. Department of Energy Phase II SBIR grant.
CERN, Geneva
The goal of the present CLIC Test Facility (CTF3) is to demonstrate the technical feasibility of specific key issues in the CLIC scheme. The extracted drive beam from the combiner ring (CR), of 35 A in magnitude and 140 ns duration, is sent to the new CLic EXperimental area (CLEX) facility. A Tail Clipper (TC) is required, in the CR to CLEX transfer line, to allow the duration of the extracted beam pulse to be adjusted. Fours sets of striplines are used for the tail clipper, each consisting of a pair of deflector plates driven to equal but opposite potential. The tail clipper kick must have a fast field rise-time, of not more than 5 ns, in order to minimize uncontrolled beam loss. High voltage MOSFET switches have been chosen to meet the demanding specifications for the semiconductor switches for the modulator of the tail clipper. This paper discusses the design of the modulator; measurement data obtained during testing and operation of the tail clipper is presented and analyzed.
CERN, Geneva
Fast kicker magnets are used to inject beam into and eject beam out of the CERN SPS accelerator ring. These kickers are generally ferrite loaded transmission line type magnets with a rectangular shaped aperture through which the beam passes. Unless special precautions are taken the impedance of the ferrite yoke can provoke significant beam induced heating, even above the Curie temperature of ferrite. In addition the impedance can contribute to beam instabilities. In this paper different variants of the coaxial wire method, both for measuring longitudinal and transverse impedance, are briefly discussed in a tutorial manner and do's and don'ts are shown on practical examples. In addition we present the results of several impedance measurements for SPS kickers using the wire method and compare those results with theoretical models.
Fermilab, Batavia
Funding: Fermilab is operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
A fast kicker magnet has been designed for use in Main Injector at Fermilab. The magnet will be used for controlled removal of unbunched beam created in the slip stacking process. The strength of each of the six magnets is 75 G·m at 500 A. The aperture is 11.4 cm wide x 5.3 cm high x 64 cm long. The field rise time from 3% to 97% of less than 57 ns has been achieved along with a flattop variation of less than ±3% variation. Results of simulation and measurements will be presented. The pulser is described in a companion paper.
Fermilab, Batavia
Funding: Fermilab is operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
A fast kicker power supply has been designed for use in the Main Injector at Fermilab. The system will be used for controlled removal of unbunched beam created in the slip stacking process. A switch operating at 50 kV with a 3% to 97% rise time of less than 25 ns into a 50 Ω load is required. A thyratron and enclosure have been designed. A pulse length of 1.6 us is required so a cable pulse forming line is used. Results with and without a ferrite pulse sharpening line will be presented. The magnet is described in a companion paper.
Fermilab, Batavia
Funding: Operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
A high voltage modulator has been built and installed at Fermi National Accelerator Laboratory for the purpose of driving the gun anode of the Tevatron Electron Lens (TEL). It produces a defined voltage for each of the 36 (anti)proton bunches. This modulator employs five transformers to produce high voltage at a high repetition rate and high duty factor. It is capable of outputting sustained complex waveforms having peak voltages over 6 kV and average periodic rates up to 450 kHz with voltage transitions occurring at 395 ns intervals. This paper describes key aspects of the hardware design and performance.
FEL/Duke University, Durham, North Carolina
BINP SB RAS, Novosibirsk
Funding: Supported by US DoE grant #DE-FG02-01ER41175
The Duke FEL/HIGS (Free electron laser/High Intensity Gamma-ray source) facility has recently undergone through a series of major upgrade. As a part of this upgrade, a kicker system was designed to provide reliable injection from the booster into the storage ring at any energy chosen from the range of 240 MeV to 1.2 GeV. Relatively new and not sufficiently studied switching device has been selected as a basic component to build a set of nanosecond resolution high-voltage generators. So called Pseudo-Spark Switch (PSS), also known as a cold cathode thyratron, has the same or slightly better jitter, reasonable range of switched high voltages and significantly lower heater power as compared to the traditional “hot” thyratrons. Despite of the fact that it requires more complicated triggering system, this device still seems very attractive as a driver for short pulse kickers. Almost three years of operation of the Duke FEL facility has revealed number of advantages and challenges related to the thyratrons of this type. In this paper we depict design features of the kicker system, discuss some accomplished improvements and summarize our three year experience.
INFN/LNF, Frascati (Roma)
New injection stripline kickers are operating since December 2007 at the DAΦNE collider. They are designed to operate with very short pulse generators to perturb only the injected bunch and the two stored adjacent ones at 2.7 ns and are a test for the design of the fast kickers of the damping ring of the International Linear Collider (ILC). Stripline frequency response and impedance measurements have been performed to characterize the structure and are compared to the simulation results. Operational performances are also described, pointing out the problems occured and the flexibility of the stripline structure that worked with both the short and the old pulse generators and has been used as an additional damping kicker to improve the efficiency of the horizontal multibunch feedback system.
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken
The main circuit of the switching power supplies for the injection bump system is composed of multiple-connection of the IGBT assemblies. The element of the IGBT assembly, which is the power supply of the shift bump-magnets, is a type of 3300V-1200A and 6 kHz in elementary frequency. The power supply has the output performance of 20 kA / 6.6 kV. The synthetic frequency of the multiple-connection assemblies is over 48 kHz and the tracking error less than 1 % is proved. The beam commissioning test of long-term operation for about three-week was performed. The deviation of the exciting current from the programmed current pattern has been confirmed less than 1%. The peculiar characteristic of the pulse power supply has been obtained by the analysis on the frequency response of the exciting current and the magnetic field. In the FFT analytical result of the magnetic field, the peaks of 48 kHz and its higher harmonics that are related to the switching frequency was observed. The ground loop current and the voltage were also measured.
LBNL, Berkeley, California
Funding: *Work supported by the Director, Office of Science, Office of Basic Energy Sciences, Materials Science and Engineering Division, of the Department of Energy under contract No. DE-AC02-05CH11231.
ALS is the 1.9GeV third generation synchrotron light source which has been operating since 1993 at Berkeley National Lab. Our team is now working on the design of a new RF power source (replacement of the existing 320kW klystron with 4 IOT’s). In the new design the existing conventional crow-bar klystron protection system will be replaced with a fast disconnect switch. The switch will be constructed out of 16 high-voltage IGBT’s connected in series equipped with static and dynamic balancing system. The main advantage of using this new technology is faster action and virtually no stress for the components of the high voltage power supply. This paper will describe the hardware design process and the test results of the prototype switch unit.
PSI, Villigen
At PSI, a new and very intensive Ultra-Cold Neutron (UCN) source based on the spallation principle will start operation at the end of 2009. From then on, two neutron spallation sources - the continuous wave SINQ and the macro-pulsed UCN source will be running concurrently at PSI. The 590 MeV, 1.2 MW proton beam will be switched towards the new spallation target for about 8 s every 800 s. This operation can be accomplished by means of a fast kicker magnet with a rise-time shorter than 1 ms. A beam dump capable of absorbing the full-intensity beam for a few milliseconds has been installed after the last bending magnet so that the kicking process and the beam diagnostic can be checked well before the UCN facility will be ready for operation. Recent tests have demonstrated the capability of switching the 1.2 MW beam with negligible losses and to center it through the beam line by using fast beam position monitors. Much longer beam pulses (up to 6 seconds) with reduced beam intensity have also been performed successfully.
PAL, Pohang, Kyungbuk
JASRI/SPring-8, Hyogo-ken
Funding: This work was supported by the MEST (Ministry of Education, Science and Technology) and the POSCO (POhang iron and Steel making COmpany) in Korea.
The PLS-II, the major upgrade program of the PLS (Pohang Light Source, a 2.5-GeV 3rd generation light source), is planned at the Pohang Accelerator Laboratory. The PLS 2.5-GeV linear accelerator, being the full-energy injector for the PLS storage ring, should be upgraded to provide the beam energy of 3 GeV. For the PLS-II linac, we are going to establish a dual electron gun system in which two guns will be on the accelerator beamline with a bending magnet enabling immediate switching of guns. The dual gun system is expected to achieve high reliability for the top-up injection to the PLS-II storage ring. Also the gun will be upgraded to provide the beam energy of 200 keV and a pulse high-voltage modulator will be constructed. Fifteen-section PFNs will be connected in series to make final impedance of approximately 17.3 ohm. A new modulator applying the inverter technology will be used to charge the PFN and obtain more stable charging performances. In this article the authours would like to report on the design status of the accelerator beamline and inverter modulator for the dual gun system.
SLAC, Menlo Park, California
Funding: Work supported by the Department of Energy under contract No. DE-AC02-76SF00515.
The design and installation of the Linac Coherent Light Source* at SLAC National Accelerator Laboratory has included the development of a kicker system for selective beam bunch dumping. The kicker is based on an LC resonant topology formed by the 50 uF energy storage capacitor and the 64 uH air core magnet load and has a sinusoidal pulse period of 400us. The maximum magnet current is 500 A. The circuit is weakly damped, allowing most of the magnet energy to be recovered in the energy storage capacitor. The kicker runs at a repetition rate of 120Hz. A PLC-based control system provides remote control and monitoring of the kicker via EPICS protocol. Fast timing and interlock signals are converted by discrete peak-detect and sample-hold circuits into DC signals that can be processed by the PLC. The design and experimental characterization of the systems is presented.
*http://ssrl.slac.stanford.edu/lcls/
SLAC, Menlo Park, California
Funding: Work supported by the U.S. Department of Energy under contract DE-AC02-76SF00515
A program is underway at SLAC to develop a Marx-topology klystron modulator for the International Linear Collider* project. It is envisioned as a smaller, lower cost, and higher reliability alternative to the bouncer-topology baseline design. The application requires 120 kV (±0.5%), 140 A, 1.6 ms pulses at a rate of 5 Hz. The Marx constructs the high voltage pulse without an output transformer, large at these parameters, by instead combining a number of lower voltage cells in series. The modularity of the Marx topology is further exploited to achieve a redundant, high-availability design. The ILC Marx employs solid state elements; IGBTs and diodes, to control the charge, discharge and isolation of the cells. The SLAC designs are oil-free; air is used for high voltage insulation and cooling. The first generation prototype, P1, is undergoing life testing. Development of a second generation prototype, P2, is underway. Status updates for both prototypes will be presented.
*ILC Reference Design Report, http://www.linearcollider.org/cms/?pid=1000437
SLAC, Menlo Park, California
Funding: Work supported by the Department of Energy under contract No. DE-AC02-76SF00515
The injection and extraction kickers (50 Ω) for the ILC damping rings will require highly reliable modulators to deliver ±5 kV, 2 ns flattop (~1 ns rise and fall time) electrical pulses at up to 6 MHz*. An effort is underway at SLAC National Accelerator Laboratory to meet these requirements using a transmission line adder topology to combine the output of an array of ~1 kV modules. The modules employ an ultra-fast hybrid driver/MOSFET that can switch 33 A in 1.2 ns. Experimental results for a scale adder structure will be presented.
*ILC Reference Design Report, http://www.linearcollider.org/cms/?pid=1000437
SLAC, Menlo Park, California
ORNL, Oak Ridge, Tennessee
Funding: Work supported by the Department of Energy under contract No. DE-AC02-76SF00515.
The 1-MW High Voltage Converter Modulators* have operated in excess of 250,000 hours at the Spallation Neutron Source. Increased demands on the accelerator performance require increased modulator reliability. An effort is underway at SLAC National Accelerator Laboratory to redesign the modulator H-bridge switch plate with the goals of increasing reliability and performance**. The major difference between the SLAC design and the existing design is the use of press-pack IGBTs. Compared to other packaging options, these IGBTs have been shown to have increased performance in pulsed-power applications, have increased cooling capability, and do not fragment and disassemble during a fault event. An overview of the SLAC switch plate redesign is presented. Design steps including electrical modeling of the modulator and H-bridge, development of an integrated IGBT clamping mechanism, and heat sink performance validation are discussed. Experimental results will be presented comparing electrical performance of the SLAC switch plate to the existing switchplate under normal and fault conditions.
*W. A. Reass, et al., “Design, Status, and First Operations of the Spallation Neutron Source Polyphase
”, PAC, 2003
**M.A. Kemp, et al., “Next Generation IGBT Switch Plate
,” LINAC, 2008.
SLAC, Menlo Park, California
ORNL, Oak Ridge, Tennessee
Funding: Work supported by the Department of Energy under contract No. DE-AC02-76SF00515.
SLAC National Accelerator Laboratory is developing a next generation H-bridge switch plate*, a critical component of the SNS High Voltage Converter Modulators**. As part of that effort, a new IGBT gate driver has been developed. The drivers are an integral part of the switch plate, which are essential to ensuring fault-tolerant, high-performance operation of the modulator. The redesigned drivers improve upon the existing gate drives in several ways. The new gate driver has improved fault detection and suppression capabilities; suppression of shoot-through and over-voltage conditions, monitoring of excess di/dt and Vce,sat, and redundant power isolation are some of the added features. Also, triggering insertion delay is reduced by a factor of four compared to the existing driver. This presentation details the design and performance of the new IGBT gate driver. A detailed schematic and description of the construction are included. Operation of the fast over-current detection circuits, active IGBT over-voltage protection circuit, shoot-through prevention and control power isolation breakdown detection circuit are discussed.
*W. A. Reass, et al., “Design, Status, and First Operations of the Spallation Neutron Source Polyphase
”, PAC, 2003
**M.A. Kemp, et al., “Next Generation IGBT Switch Plate
,” LINAC, 2008.
SLAC, Menlo Park, California
Funding: Work supported by the U.S. Department of Energy under contract DE-AC02-76SF00515
Introduced by the U.S. Navy more than a decade ago*, the concept of Power Electronic Building Blocks (PEBBs) has been successfully applied in various applications. It is well accepted within the power electronics arena that this concept offers the potential to achieve increased levels of modularity and compactness. This approach is thus ideally suited for applications where easy serviceability and high availability are key, such as the ILC. This paper presents a building block approach for designing Marx modulators. First the concept of "bricks and buses" is briefly discussed. Then a PEBB-oriented design is presented for the basic Marx cell of a 32-cell Marx modulator to power an ILC klystron; 120 kV, 140 A, 1.6 ms pulses at a repetition rate of 5 Hz. Each basic Marx cell is composed of a main cell and a correction cell that compensates the main cell droop. The main cell has a stored energy of 2.1 kJ per Marx cell and the correction cell an additional 0.5 kJ. This design allows over 30% of the total stored energy in the Marx modulator, 84 kJ, to be delivered in the output pulse, 26.9 kJ, while keeping the droop within a ±0.5% range.
*T. Ericsen. 'Power Electronics Building Blocks - A systematic approach to power electronics.' In: Proceedings of Power Engineering Society Summer Meeting, Seattle, WA, 16-20 July 2000.
Tsukuba University, Ibaraki
A new concept of a fast magnetic kicker system - the bridged-T network lumped kicker - is proposed. The rise time is as fast as that of a transmission line kicker, while the input-impedance can be matched with a characteristic impedance of the pulse power supply. The proposed scheme is compared with several conventional schemes. The demonstration of this proposed scheme is also performed. The results show expected performances.
USTC/NSRL, Hefei, Anhui
Funding: Work supported by National Natural Science Foundation of China (No.10175062 & 10575100).
The light pulse interval adjustment at Hefei Light Source (HLS) can be realized by using pulsed orbit bump technique, which requires for high-frequency repetitive, high magnetic flux density, short pulse kicker magnet system of which the power supply modulator should be specially designed. The technique of solid state modulator based on MOSFET is being developed in National synchrotron Radiation Laboratory (NSRL). In this paper, the design of a prototype of solid-state modulator with 20 MOSFETs in parallel is introduced, including triggering system, drive circuit, transformer configuration. The oscillation induced by parasitic capacitance and inductance is discussed. This prototype with four stage adder can achieve 100ns width power pulse output with 112A, 2.4 kV to the kicker.
LLNL, Livermore, California
TomoTherapy, Madison
TPL, Albuquerque, NM
CPAC, Madison
Funding: This work performed under the auspices of the U.S. Department of Energy by Lawrence Livvermore National Laboratory under Contract DE-AC52-07NA27344.
The dielectric wall accelerator* (DWA) system being developed at the Lawrence Livermore National Laboratory (LLNL) uses fast switched high voltage transmission lines to generate pulsed electric fields on the inside of a high gradient insulating (HGI) acceleration tube. High electric field gradients are achieved by the use of alternating insulators and conductors and short pulse times. The system is capable of accelerating any charge to mass ratio particle. Applications of high gradient proton and electron versions of this accelerator will be discussed. The status of the developmental new technologies that make the compact system possible will be reviewed. These include high gradient vacuum insulators, solid dielectric materials, photoconductive switches and compact proton sources.
*Patents pending.
CERN, Geneva
Fast kicker magnets are used to inject beam into and eject beam out of the CERN SPS accelerator ring. These kickers are generally ferrite loaded transmission line type magnets with a rectangular shaped aperture through which the beam passes. Unless special precautions are taken the impedance of the ferrite yoke can provoke significant beam induced heating, over several hours, even above the Curie temperature of the ferrite. At present the nominal bunch spacing in the SPS is 25 ns, however for an early stage of LHC operation it is preferable to have 50 ns bunch spacing. Machine Development (MD) studies have been carried out with an inter-bunch spacing of 25 ns, 50 ns or 75 ns. For some of the SPS kicker magnets the 75 ns bunch spacing resulted in considerable beam induced heating. In addition the MDs showed that 50 ns bunch spacing could result in a very rapid pressure rise in the kicker magnet and thus cause an interlock. This paper discusses the MD observations of the SPS kickers and analyses the available data to provide explanations for the phenomena: possible remedies are also discussed.
Omega-P, Inc., New Haven, Connecticut
Columbia University, New York
Yale University, Beam Physics Laboratory, New Haven, Connecticut
NSC/KIPT, Kharkov
Funding: US Department of Energy, Office of High Energy Physics, Advanced Accelerator R & D.
A rectangular two-beam dielectric wakefield accelerator (DWA) module is described which, when energized by a 14 MeV, 50 nC drive bunch moving in one channel, is shown to deflect a test bunch which originates from an independent source moving in a parallel channel. We show that such a module, 30 cm in length, can deflect transversely a 1 GeV electron by ~ 1 mrad in 1 ns, after which a following bunch can pass undeflected. Apparatus required to accomplish this task consists of a laser-cathode RF gun and an optional linac to generate the drive bunch. The associated DWA components could be used for kicker applications in a storage ring or a more energetic electron linear accelerator. An example we describe is tailored to a DWA demonstration project underway at the Argonne Wakefield Accelerator, but the design can be altered to allow for changes including a lower-energy but still relativistic drive bunch. The kicker, through appropriate design, can deflect one out of several bunches in a storage ring, leaving the remaining bunches essentially unaffected by the structure.