IPAC2015 - List of Authors (Molina Marinas, E.)

Paper	Title	Page
MOPTY043	Update on the Development of the New Electronic Instrumentation for the LIPAc/IFMIF Beam Position Monitors	1025
	A. Guirao, D. Jiménez-Rey, L.M. Martinez Fresno, E. Molina Marinas, J. Mollá, I. Podadera, I. Rivera CIEMAT, Madrid, Spain
	Funding: This work has been funded by the Spanish Ministry of Economy and Competitiveness under the project FIS2013-40860-R and the Agreement as published in BOE, 16/01/2013, page 1988 Among all the LIPAc/IFMIF accelerator diagnostics instrumentation, the Beam Position Monitors (BPMs) are a cornerstone for its operation. An electronics system centered on self-calibration and extraction of beam phase information for Time Of Flight measurement is proposed for the twenty BPM stations distributed along the accelerator. The system under development is a fully digital instrumentation which incorporates automatic calibration of the monitors' signals and allows monitoring of both fundamental and second signal harmonics. The current state of the development and first experimental results of the system on the test bench will be presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPTY043
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPWI015	Experience on Serial Production of the Quadrupole Movers with Submicrometric Repeatability for the European XFEL*	2271
	J. Munilla, J. Calero, L. García-Tabarés, A. Guirao, J.L. Gutiérrez, T. Martínez, E. Molina Marinas, F. Toral, C. Vázquez CIEMAT, Madrid, Spain J.A. Gorrotxategi, M. Tarragual ZEHATZ, Mendaro, Spain B. Junkera, A. Urzainki DMP, Mendaro, Spain C. Martins, E. Ramiro, F. Ramiro RAMEM, Madrid, Spain
	Funding: This work is partially supported by the Spanish Ministry of Science and Innovation under SEI Resolution on 17-September-2009 and Project ref. AIC10-A-000524 CIEMAT is in charge of the design and manufacturing of the quadrupole movers with submicrometric repeatability for the XFEL. EU intersections. Prototyping of these precision devices was successful but manufacturing them in a serial production scheme (101 units) implies some changes at design, fabrication procedures and quality controls. This paper will present some of the main problems and solutions adopted to transform a prototype made at a research facility into a serial production at a conventional industrial company. Also, it describes the inspection and tests, the quality controls and reporting procedures. All the devices have been validated and recepted. This paper describes the adopted procedure and the performance of the serial units.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-TUPWI015
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Update on the Development of the New Electronic Instrumentation for the LIPAc/IFMIF Beam Position Monitors

1025

A. Guirao, D. Jiménez-Rey, L.M. Martinez Fresno, E. Molina Marinas, J. Mollá, I. Podadera, I. Rivera
CIEMAT, Madrid, Spain

Funding: This work has been funded by the Spanish Ministry of Economy and Competitiveness under the project FIS2013-40860-R and the Agreement as published in BOE, 16/01/2013, page 1988
Among all the LIPAc/IFMIF accelerator diagnostics instrumentation, the Beam Position Monitors (BPMs) are a cornerstone for its operation. An electronics system centered on self-calibration and extraction of beam phase information for Time Of Flight measurement is proposed for the twenty BPM stations distributed along the accelerator. The system under development is a fully digital instrumentation which incorporates automatic calibration of the monitors' signals and allows monitoring of both fundamental and second signal harmonics. The current state of the development and first experimental results of the system on the test bench will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPTY043

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPWI015

Experience on Serial Production of the Quadrupole Movers with Submicrometric Repeatability for the European XFEL*

2271

J. Munilla, J. Calero, L. García-Tabarés, A. Guirao, J.L. Gutiérrez, T. Martínez, E. Molina Marinas, F. Toral, C. Vázquez
CIEMAT, Madrid, Spain
J.A. Gorrotxategi, M. Tarragual
ZEHATZ, Mendaro, Spain
B. Junkera, A. Urzainki
DMP, Mendaro, Spain
C. Martins, E. Ramiro, F. Ramiro
RAMEM, Madrid, Spain

Funding: This work is partially supported by the Spanish Ministry of Science and Innovation under SEI Resolution on 17-September-2009 and Project ref. AIC10-A-000524
CIEMAT is in charge of the design and manufacturing of the quadrupole movers with submicrometric repeatability for the XFEL. EU intersections. Prototyping of these precision devices was successful but manufacturing them in a serial production scheme (101 units) implies some changes at design, fabrication procedures and quality controls. This paper will present some of the main problems and solutions adopted to transform a prototype made at a research facility into a serial production at a conventional industrial company. Also, it describes the inspection and tests, the quality controls and reporting procedures. All the devices have been validated and recepted. This paper describes the adopted procedure and the performance of the serial units.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-TUPWI015

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)