IPAC2013 - List of Authors (Yoshida, M.)

Paper

Title

Page

Development of Better Quantum Efficiency and Long Lifetime Iridium Cerium Photocathode for High Charge electron RF Gun

327

D. Satoh
TIT, Tokyo, Japan
N. Hayashizaki
RLNR, Tokyo, Japan
M. Yoshida
KEK, Ibaraki, Japan

We developed an Ir5Ce photocathode as a high charge electron source for SuperKEKB electron linac. The required electron beam parameters are 5 nC and 10 mm•mrad from the electron gun of the SuperKEKB electron linac. We plan to generate this electron beam using a laser-driven RF gun installed with a photocathode that has a long lifetime and a high-power laser system through more than a year without replacement. Therefore, we focused on the Ir5Ce compound as a new photocathode which has a high melting point (> 2100 K) and a low work function (2.57 eV). The results of measurements showed that the quantum efficiency of Ir5Ce photocathode was 1.0×10^-4 treated by the laser cleaning using the 4nd harmonic of Nd:YAG laser or the heater treatment. Furthermore, its photoemission properties could be maintained for a long term even if its photocathode was in the low vacuum conditions ( ～10^-6 Pa) since the Ir5Ce compound is far less contaminated than other photocathodes. Finally, We have succeed to generate electron beams of 4.4 nC by the Ir5Ce photocathode installed at the 3-2 sector DAW type RF gun and accelerate it through a linac end in KEK electron linac.

TUOCB103

Quasi Traveling Wave Side Couple RF Gun for SuperKEKB

1117

T. Natsui, Y. Ogawa, M. Yoshida, X. Zhou
KEK, Ibaraki, Japan

We are developing a new RF gun for SuperKEKB. High charge low emittance electron and positron beams are required for SuperKEKB. We will generate 7.0 GeV electron beam at 5 nC 20 mm-mrad by J-linac. In this linac, a photo cathode S-band RF gun will be used as the electron beam source. For this reason, we are developing an advanced RF gun. We have tested a Disk and Washer (DAW) type RF gun. Additionally, another new RF gun which has two side coupled standing wave field is developed. We call it quasi traveling wave side couple RF gun. This gun has a strong focusing field at the cathode and the acceleration field distribution also has a focusing effect. The design of RF gun and experimental results will be shown.

Slides TUOCB103 [2.959 MB]

TUPFI003

The Accelerator Design of Muon g-2 Experiment at J-PARC

1334

S. Artikova, F. Naito, M. Yoshida
KEK, Ibaraki, Japan

New muon g-2 experiment at J-PARC is aimed to improve the precise measurement of the muon g-2. In this experiment, the ultra-cold muons created in the muonium target region is reaccelerated to around 300MeV/c in momentum (210 MeV kinetic energy) to then be injected into the muon g-2 storage ring to measure the decay products depending on the muon spin. The linac has advantage over circular accelerators to shorten the reacceleration time in the limited life time of muon. The muon linac consists of the initial acceleration (to 0.01 of v/c), bunching section (0.01 to 0.08 of v/c), low beta section (0.08 to 0.3 of v/c), middle beta section (0.3 to 0.7 of v/c) and high beta section (0.7 to 0.94 of v/c). As a part of the design consideration of this linac, we mainly present the simulation result of initial acceleration and further acceleration of muons with RFQ. An electric field is used to extract the ultra-cold muons from the laser ionization region and RF field is used to create some bunches and to accelerate to higher energies.

TUPFI004

Longitudinal Manipulation to Obtain and Keep the Low Emittance and High Charge Electron Beam for SuperKEKB Injector

1337

M. Yoshida, N. Iida, T. Natsui, Y. Ogawa, S. Ohsawa, H. Sugimoto, L. Zang, X. Zhou
KEK, Ibaraki, Japan

The design strategy of SuperKEKB is based on the.nano-beam scheme. The dynamic aperture decreases due to the very small beta function at the interaction point. Thus the injector upgrade is required to obtain the low emittance and high charge beam corresponding to the short beam life and small injection acceptance. The required beam parameters are 5 nC, 20 mm mrad and 4 nC, 6 mm mrad for the electron and positron respectively. For the electron beam, we installed new photocathode RF-Gun with the focusing electric field and temporal adjusting laser system. Further the projected emittance dilution in the LINAC is an important issue for the low emittance injection. The longitudinal bunch length and shape is an important key to avoid the space charge effect and emittance dilution. The longitudinal manipulation using the temporal adjusting laser system and the bunch compression will be presented. Further the longitudinal bunch measurement will be also presented.

TUPME010

High-intensity and Low-emittance Upgrade of 7-GeV Injector Linac towards SuperKEKB

1583

K. Furukawa, M. Akemoto, D.A. Arakawa, Y. Arakida, A. Enomoto, S. Fukuda, H. Honma, R. Ichimiya, N. Iida, M. Ikeda, E. Kadokura, K. Kakihara, T. Kamitani, H. Katagiri, M. Kurashina, S. Matsumoto, T. Matsumoto, H. Matsushita, S. Michizono, K. Mikawa, T. Miura, F. Miyahara, T. Mori, H. Nakajima, K. Nakao, T. Natsui, Y. Ogawa, S. Ohsawa, F. Qiu, M. Satoh, T. Shidara, A. Shirakawa, H. Sugimoto, T. Suwada, T. Takatomi, T. Takenaka, M. Tanaka, Y. Yano, K. Yokoyama, M. Yoshida, L. Zang, X. Zhou
KEK, Ibaraki, Japan
D. Satoh
TIT, Tokyo, Japan

After a decade of successful operation at KEKB a new electron/positron collider, SuperKEKB, is being constructed to commission within FY2014. It aims at a luminosity of 8 x 10³⁵ /s.cm², 40-times higher than that of KEKB, in order to study the flavor physics of elementary particles further, by mainly squeezing the beams at the collision point. The injector linac should provide high-intensity and low-emittance beams of 7-GeV electron and 4-GeV positron by newly installing a RF-gun, a flux concentrator, and a damping ring with careful emittance and energy management. It also have to perform simultaneous top-up injections into four storage rings by pulse-to-pulse beam modulations not to interfare between three facilities of SuperKEKB, Photon Factory and PF-AR. This paper describes the injector design decisions and present status of the construction.

WEPWA015

Progress in Construction of the 35 MeV Compact Energy Recovery Linac at KEK

2159

S. Sakanaka, S. Adachi, M. Akemoto, D.A. Arakawa, S. Asaoka, K. Enami, K. Endo, S. Fukuda, T. Furuya, K. Haga, K. Hara, K. Harada, T. Honda, Y. Honda, H. Honma, T. Honma, K. Hosoyama, K. Hozumi, E. Kako, Y. Kamiya, H. Katagiri, H. Kawata, Y. Kobayashi, Y. Kojima, Y. Kondou, T. Kume, T. Matsumoto, H. Matsumura, H. Matsushita, S. Michizono, T. Miura, T. Miyajima, S. Nagahashi, H. Nakai, H. Nakajima, N. Nakamura, K. Nakanishi, K. Nakao, K.N. Nigorikawa, T. Nogami, S. Noguchi, S. Nozawa, T. Obina, T. Ozaki, F. Qiu, H. Sagehashi, H. Sakai, S. Sasaki, K. Satoh, M. Satoh, T. Shidara, M. Shimada, K. Shinoe, T. Shioya, T. Shishido, M. Tadano, T. Takahashi, R. Takai, T. Takenaka, Y. Tanimoto, M. Tobiyama, K. Tsuchiya, T. Uchiyama, A. Ueda, K. Umemori, K. Watanabe, M. Yamamoto, Y. Yamamoto, Y. Yano, M. Yoshida
KEK, Ibaraki, Japan
E. Cenni
Sokendai, Ibaraki, Japan
R. Hajima, S.M. Matsuba, R. Nagai, N. Nishimori, M. Sawamura, T. Shizuma
JAEA, Ibaraki-ken, Japan
H. Takaki
ISSP/SRL, Chiba, Japan

The 35-MeV Compact Energy Recovery Linac (the Compact ERL or cERL) is under construction at the High Energy Accelerator Research Organization (KEK) in Japan. With the Compact ERL, we aim at establishing cutting-edge technologies for the GeV-class ERL-based synchrotron light source. To install the accelerator components of the cERL, we have constructed a shielding room having an area of about 60 m x 20 m. We have then installed a 500-kV DC photocathode gun, a 5-MV superconducting (SC) cryomodule for the injector, a 30-MV SC cryomodule for the main linac, and some of the other components. High-power test on the main SC cryomodule is underway in December, 2012. High-power or high-voltage tests on the injector cryomodule and on the DC gun are planned during January to March, 2013. An injector of the Compact ERL will be commissioned in April, 2013. We report the newest status of its construction.

WEPME018

Ytterbium Laser Development of DAW RF Gun for SuperKEKB

2965

X. Zhou, T. Natsui, Y. Ogawa, M. Yoshida
KEK, Ibaraki, Japan

For obtaining higher luminosity in the SuperKEKB, the photocathode RF electron gun with strong electric focusing field for high-current, low-emittance beams will be employed in the injector linac. The electron beams with a charge of 5 nC and a normalized emittance of 10 μm are expected to be generated in the photocathode RF gun by using the laser source with a center wavelength of 260 nm and a pulse width of 30 ps. Furthermore, for reducing the emittance, the laser pulse width should be reshaped from Gaussian to rectangle structure. Therefore, Ytterbium (Yb)-doped laser system that provides broader bandwidth, higher amplify efficiency and higher output power is employed. The laser system starts with a large mode-area Yb-doped fiber-based amplifier system, which consists of a passively mode-locked femtosecond Yb-fiber oscillator and two steps Yb-fiber amplifier. To obtain the several 10mJ-class pulse energy, a Yb:YAG thin-disk regenerative solid-state amplifier is employed. Deep UV pulses for the photocathode are generated by using two frequency-doubling stages. High pulse energy and good stability would be expected.

Paper	Title	Page
MOPFI023	Development of Better Quantum Efficiency and Long Lifetime Iridium Cerium Photocathode for High Charge electron RF Gun	327
	D. Satoh TIT, Tokyo, Japan N. Hayashizaki RLNR, Tokyo, Japan M. Yoshida KEK, Ibaraki, Japan
	We developed an Ir5Ce photocathode as a high charge electron source for SuperKEKB electron linac. The required electron beam parameters are 5 nC and 10 mm•mrad from the electron gun of the SuperKEKB electron linac. We plan to generate this electron beam using a laser-driven RF gun installed with a photocathode that has a long lifetime and a high-power laser system through more than a year without replacement. Therefore, we focused on the Ir5Ce compound as a new photocathode which has a high melting point (> 2100 K) and a low work function (2.57 eV). The results of measurements showed that the quantum efficiency of Ir5Ce photocathode was 1.0×10^-4 treated by the laser cleaning using the 4nd harmonic of Nd:YAG laser or the heater treatment. Furthermore, its photoemission properties could be maintained for a long term even if its photocathode was in the low vacuum conditions ( ～10^-6 Pa) since the Ir5Ce compound is far less contaminated than other photocathodes. Finally, We have succeed to generate electron beams of 4.4 nC by the Ir5Ce photocathode installed at the 3-2 sector DAW type RF gun and accelerate it through a linac end in KEK electron linac.

TUOCB103	Quasi Traveling Wave Side Couple RF Gun for SuperKEKB	1117
	T. Natsui, Y. Ogawa, M. Yoshida, X. Zhou KEK, Ibaraki, Japan
	We are developing a new RF gun for SuperKEKB. High charge low emittance electron and positron beams are required for SuperKEKB. We will generate 7.0 GeV electron beam at 5 nC 20 mm-mrad by J-linac. In this linac, a photo cathode S-band RF gun will be used as the electron beam source. For this reason, we are developing an advanced RF gun. We have tested a Disk and Washer (DAW) type RF gun. Additionally, another new RF gun which has two side coupled standing wave field is developed. We call it quasi traveling wave side couple RF gun. This gun has a strong focusing field at the cathode and the acceleration field distribution also has a focusing effect. The design of RF gun and experimental results will be shown.
	Slides TUOCB103 [2.959 MB]

TUPFI003	The Accelerator Design of Muon g-2 Experiment at J-PARC	1334
	S. Artikova, F. Naito, M. Yoshida KEK, Ibaraki, Japan
	New muon g-2 experiment at J-PARC is aimed to improve the precise measurement of the muon g-2. In this experiment, the ultra-cold muons created in the muonium target region is reaccelerated to around 300MeV/c in momentum (210 MeV kinetic energy) to then be injected into the muon g-2 storage ring to measure the decay products depending on the muon spin. The linac has advantage over circular accelerators to shorten the reacceleration time in the limited life time of muon. The muon linac consists of the initial acceleration (to 0.01 of v/c), bunching section (0.01 to 0.08 of v/c), low beta section (0.08 to 0.3 of v/c), middle beta section (0.3 to 0.7 of v/c) and high beta section (0.7 to 0.94 of v/c). As a part of the design consideration of this linac, we mainly present the simulation result of initial acceleration and further acceleration of muons with RFQ. An electric field is used to extract the ultra-cold muons from the laser ionization region and RF field is used to create some bunches and to accelerate to higher energies.

TUPFI004	Longitudinal Manipulation to Obtain and Keep the Low Emittance and High Charge Electron Beam for SuperKEKB Injector	1337
	M. Yoshida, N. Iida, T. Natsui, Y. Ogawa, S. Ohsawa, H. Sugimoto, L. Zang, X. Zhou KEK, Ibaraki, Japan
	The design strategy of SuperKEKB is based on the.nano-beam scheme. The dynamic aperture decreases due to the very small beta function at the interaction point. Thus the injector upgrade is required to obtain the low emittance and high charge beam corresponding to the short beam life and small injection acceptance. The required beam parameters are 5 nC, 20 mm mrad and 4 nC, 6 mm mrad for the electron and positron respectively. For the electron beam, we installed new photocathode RF-Gun with the focusing electric field and temporal adjusting laser system. Further the projected emittance dilution in the LINAC is an important issue for the low emittance injection. The longitudinal bunch length and shape is an important key to avoid the space charge effect and emittance dilution. The longitudinal manipulation using the temporal adjusting laser system and the bunch compression will be presented. Further the longitudinal bunch measurement will be also presented.

TUPME010	High-intensity and Low-emittance Upgrade of 7-GeV Injector Linac towards SuperKEKB	1583
	K. Furukawa, M. Akemoto, D.A. Arakawa, Y. Arakida, A. Enomoto, S. Fukuda, H. Honma, R. Ichimiya, N. Iida, M. Ikeda, E. Kadokura, K. Kakihara, T. Kamitani, H. Katagiri, M. Kurashina, S. Matsumoto, T. Matsumoto, H. Matsushita, S. Michizono, K. Mikawa, T. Miura, F. Miyahara, T. Mori, H. Nakajima, K. Nakao, T. Natsui, Y. Ogawa, S. Ohsawa, F. Qiu, M. Satoh, T. Shidara, A. Shirakawa, H. Sugimoto, T. Suwada, T. Takatomi, T. Takenaka, M. Tanaka, Y. Yano, K. Yokoyama, M. Yoshida, L. Zang, X. Zhou KEK, Ibaraki, Japan D. Satoh TIT, Tokyo, Japan
	After a decade of successful operation at KEKB a new electron/positron collider, SuperKEKB, is being constructed to commission within FY2014. It aims at a luminosity of 8 x 10³⁵ /s.cm², 40-times higher than that of KEKB, in order to study the flavor physics of elementary particles further, by mainly squeezing the beams at the collision point. The injector linac should provide high-intensity and low-emittance beams of 7-GeV electron and 4-GeV positron by newly installing a RF-gun, a flux concentrator, and a damping ring with careful emittance and energy management. It also have to perform simultaneous top-up injections into four storage rings by pulse-to-pulse beam modulations not to interfare between three facilities of SuperKEKB, Photon Factory and PF-AR. This paper describes the injector design decisions and present status of the construction.

WEPWA015	Progress in Construction of the 35 MeV Compact Energy Recovery Linac at KEK	2159
	S. Sakanaka, S. Adachi, M. Akemoto, D.A. Arakawa, S. Asaoka, K. Enami, K. Endo, S. Fukuda, T. Furuya, K. Haga, K. Hara, K. Harada, T. Honda, Y. Honda, H. Honma, T. Honma, K. Hosoyama, K. Hozumi, E. Kako, Y. Kamiya, H. Katagiri, H. Kawata, Y. Kobayashi, Y. Kojima, Y. Kondou, T. Kume, T. Matsumoto, H. Matsumura, H. Matsushita, S. Michizono, T. Miura, T. Miyajima, S. Nagahashi, H. Nakai, H. Nakajima, N. Nakamura, K. Nakanishi, K. Nakao, K.N. Nigorikawa, T. Nogami, S. Noguchi, S. Nozawa, T. Obina, T. Ozaki, F. Qiu, H. Sagehashi, H. Sakai, S. Sasaki, K. Satoh, M. Satoh, T. Shidara, M. Shimada, K. Shinoe, T. Shioya, T. Shishido, M. Tadano, T. Takahashi, R. Takai, T. Takenaka, Y. Tanimoto, M. Tobiyama, K. Tsuchiya, T. Uchiyama, A. Ueda, K. Umemori, K. Watanabe, M. Yamamoto, Y. Yamamoto, Y. Yano, M. Yoshida KEK, Ibaraki, Japan E. Cenni Sokendai, Ibaraki, Japan R. Hajima, S.M. Matsuba, R. Nagai, N. Nishimori, M. Sawamura, T. Shizuma JAEA, Ibaraki-ken, Japan H. Takaki ISSP/SRL, Chiba, Japan
	The 35-MeV Compact Energy Recovery Linac (the Compact ERL or cERL) is under construction at the High Energy Accelerator Research Organization (KEK) in Japan. With the Compact ERL, we aim at establishing cutting-edge technologies for the GeV-class ERL-based synchrotron light source. To install the accelerator components of the cERL, we have constructed a shielding room having an area of about 60 m x 20 m. We have then installed a 500-kV DC photocathode gun, a 5-MV superconducting (SC) cryomodule for the injector, a 30-MV SC cryomodule for the main linac, and some of the other components. High-power test on the main SC cryomodule is underway in December, 2012. High-power or high-voltage tests on the injector cryomodule and on the DC gun are planned during January to March, 2013. An injector of the Compact ERL will be commissioned in April, 2013. We report the newest status of its construction.

WEPME018	Ytterbium Laser Development of DAW RF Gun for SuperKEKB	2965
	X. Zhou, T. Natsui, Y. Ogawa, M. Yoshida KEK, Ibaraki, Japan
	For obtaining higher luminosity in the SuperKEKB, the photocathode RF electron gun with strong electric focusing field for high-current, low-emittance beams will be employed in the injector linac. The electron beams with a charge of 5 nC and a normalized emittance of 10 μm are expected to be generated in the photocathode RF gun by using the laser source with a center wavelength of 260 nm and a pulse width of 30 ps. Furthermore, for reducing the emittance, the laser pulse width should be reshaped from Gaussian to rectangle structure. Therefore, Ytterbium (Yb)-doped laser system that provides broader bandwidth, higher amplify efficiency and higher output power is employed. The laser system starts with a large mode-area Yb-doped fiber-based amplifier system, which consists of a passively mode-locked femtosecond Yb-fiber oscillator and two steps Yb-fiber amplifier. To obtain the several 10mJ-class pulse energy, a Yb:YAG thin-disk regenerative solid-state amplifier is employed. Deep UV pulses for the photocathode are generated by using two frequency-doubling stages. High pulse energy and good stability would be expected.