Author: Zhou, X.
Paper Title Page
TUPPD057 High Charge Low Emittance RF Gun for SuperKEKB 1533
  • T. Natsui, Y. Ogawa, M. Yoshida, X. Zhou
    KEK, Ibaraki, Japan
  We are developing a new RF gun for SuperKEKB. We are upgrading KEKB to SuperKEKB now. High charge low emittance electron and positron beams are required for SuperKEKB. We will generate 7.0 GeV electron beam at 5 nC 20 mm-mrad by J-linac. In this linac, a photo cathode S-band RF gun will be used as the electron beam source. For this reason, we are developing an advanced RF gun. Now, we are testing a Disk and Washer (DAW) type RF gun. Its photo cathode material is LaB6. Normally, LaB6 is used as a thermionic cathode, but it is suitable for long-life photo cathode operation. This gun has a strong focusing field at the cathode and the acceleration field distribution also has a focusing effect. We will obtain 3.2 MeV beam energy with the gun. The design of RF gun and experimental results will be shown.  
WEPPD056 Ytterbium Fiber Laser System of DAW RF Gun for SuperKEKB 2648
  • X. Zhou, T. Natsui, Y. Ogawa, M. Yoshida
    KEK, Ibaraki, Japan
  For obtaining higher luminosity in the SuperKEKB, the photocathode DAW-type RF gun for high-current, low-emittance beams will be employed in the injector linac. The electron beams with a charge of 5 nC and a normalized emittance of 10 micrometer are expected generate in the photocathode RF gun by using the laser source with a center wavelength of 260 nm and a pulse width of 30 ps. Fiber laser especially Ytterbium(Yb) fiber have attracted attention as one of the promising practical alternatives to usual solid-state lasers, offering high energy-extraction efficiency, high repetition rate, high output power, low-cost and so on. Introducing the Ytterbium fiber laser system, we have developed a stable laser amplifier system, which could allow steady beam injection into the SuperKEKB rings. The laser system starts with a large mode-area Yb-doped fiber-based amplifier system, which consists of a passively mode-locked femtosecond Yb-fiber oscillator. To obtain the mJ-class pulse energy, a multi-pass solid-state amplifier is employed. Deep UV pulses for the photocathode are generated by using two frequency-doubling stages. High pulse energy and good stability would be expected.  
TUPPR005 Linac Upgrade in Intensity and Emittance for SuperKEKB 1819
  • T. Higo, M. Akemoto, D.A. Arakawa, Y. Arakida, A. Enomoto, S. Fukuda, K. Furukawa, Y. Higashi, H. Honma, N. Iida, M. Ikeda, E. Kadokura, K. Kakihara, T. Kamitani, H. Katagiri, M. Kurashina, S. Matsumoto, T. Matsumoto, H. Matsushita, S. Michizono, K. Mikawa, T. Miura, F. Miyahara, T. Mori, H. Nakajima, K. Nakao, T. Natsui, Y. Ogawa, S. Ohsawa, M. Satoh, T. Shidara, A. Shirakawa, H. Sugimoto, T. Suwada, T. Takatomi, T. Takenaka, Y. Yano, K. Yokoyama, M. Yoshida, L. Zang, X. Zhou
    KEK, Ibaraki, Japan
  • D. Satoh
    TIT, Tokyo, Japan
  The SuperKEKB is designed to produce 40 times luminosity than that of the KEKB. In order to realize such a high luminosity, the injector linac should provide both electron and positron beams of about 4-5 nC/bunch, which is several times higher than before. In addition, their emittance requirement of the injection beam to the rings is 20 microns, which is a factor of a few tens smaller than before. The intensity and emittance of the electron beam are realized directly by developing the photo RF gun. In contrast, the positron intensity is increased by adopting a higher capture efficiency system with flux concentrator followed by large-aperture accelerators, while its emittance is reduced by a damping ring. For preserving such a low emittance of both beams toward the injection to the rings, the suppression of the emittance growth is crucial. To this end, the alignment of the accelerator components should be a few tens of microns, where we need an improvement by more than a factor 10. The beam-based alignment is definitely needed with better-resolution BPMs. In the present paper are reviewed the overall progress and perspective of the design and the associated component developments.