IPAC2012 - List of Authors (Veshcherevich, V.)

Paper

Title

Page

Performance of the Cornell High-Brightness, High-Power Electron Injector

20

B.M. Dunham, A.C. Bartnik, I.V. Bazarov, L. Cultrera, J. Dobbins, C.M. Gulliford, G.H. Hoffstaetter, R.P.K. Kaplan, V.O. Kostroun, Y. Li, M. Liepe, X. Liu, F. Löhl, P. Quigley, D.H. Rice, E.N. Smith, K.W. Smolenski, M. Tigner, V. Veshcherevich, Z. Zhao
CLASSE, Ithaca, New York, USA
S.S. Karkare, H. Li, J.M. Maxson
Cornell University, Ithaca, New York, USA

Funding: NSF DMR-0807731
The last year has seen significant progress in demonstrating the feasibility of a high current, high brightness photoinjector as required for the Energy Recovery Linac driven X-ray source at Cornell University. Both low emittances (0.4 mm-mrad rms normalized for 100% of the beam at 20 pC per bunch and 0.15 mm-mrad rms core emittance with 70% of the beam, and twice these values at 80 pC per bunch) and high average currents with a good lifetime well in excess of 1000 Coulombs at 5 MeV, 20 mA have been demonstrated. If these beams can be accelerated to 5 GeV without diluting the phase space, it would already provide a beam brightness higher than any existing storage ring. Operational experience, results, and the outlook for the future will be presented.

Slides MOOAA01 [1.424 MB]

WEPPC072

High Current Operation of the Cornell ERL Superconducting RF Injector Cryomodule

2378

M. Liepe, G.H. Hoffstaetter, S. Posen, P. Quigley, V. Veshcherevich
CLASSE, Ithaca, New York, USA

Cornell University has developed a SCRF injector cryomodule for the acceleration of high current, low emittance beams in continuous wave operation. This cryomodule is based on superconducting RF technology, and is currently under extensive testing in the Cornell ERL injector prototype with CW beam currents exceeding 25 mA. Strong damping of Higher-Order-Modes in the cavities is essential for high beam current operation, and is achieved by beamline RF absorber located at cryogenic temperatures in the beam pipe sections between the cavities. This paper gives an overview of the experience gained during the high beam current operation of the cryomodule.

WEPPC031

Completed Assembly of the Daresbury International ERL Cryomodule and its Implementation on ALICE

2272

P.A. McIntosh, M.A. Cordwell, P.A. Corlett, P. Davies, E. Frangleton, P. Goudket, K.J. Middleman, S.M. Pattalwar, A.E. Wheelhouse
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
S.A. Belomestnykh
BNL, Upton, Long Island, New York, USA
A. Büchner, F.G. Gabriel, P. Michel
HZDR, Dresden, Germany
J.N. Corlett, D. Li, S.M. Lidia
LBNL, Berkeley, California, USA
G.H. Hoffstaetter, M. Liepe, H. Padamsee, P. Quigley, J. Sears, V.D. Shemelin, V. Veshcherevich
CLASSE, Ithaca, New York, USA
T.J. Jones, J. Strachan
STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom
R.E. Laxdal
TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada
D. Proch, J.K. Sekutowicz
DESY, Hamburg, Germany
T.I. Smith
Stanford University, Stanford, California, USA

The completion of an optimised SRF cryomodule for application on ERL accelerators has now culminated with the successful assembly of an integrated cryomodule, following an intensive 5 years of development evolution. The cryomodule, which incorporates 2 x 7-cell 1.3 GHz accelerating structures, 3 separate layers of magnetic shielding, fully adjustable & high power input couplers and fast piezo tuners, has been installed on the ALICE ERL facility at Daresbury Laboratory. It is intended that this will permit operational optimisation for maximised efficiency demonstration, through increased Qext adjustment whilst retaining both effective energy recovery and IR-FEL lasing. The collaborative design processes employed in completing this new cryomodule development are explained, along with the assembly and implementation procedures used to facilitate its successful installation on the ALICE ERL facility.

WEPPC073

Progress on Superconducting RF Work for the Cornell ERL

2381

M. Liepe, F. Furuta, G.M. Ge, Y. He, G.H. Hoffstaetter, T.I. O'Connell, S. Posen, J. Sears, M. Tigner, N.R.A. Valles, V. Veshcherevich
CLASSE, Ithaca, New York, USA

Cornell University is developing the superconducting RF technology required for the construction of a 100 mA hard X-ray light source driven by an Energy-Recovery Linac. Prototypes of all beam line components of the 5 GeV cw SRF main linac cryomodule have been fabricated and tested in detail. This work includes an optimized 7-cell SRF cavity, a broadband HOM beamline absorber, a cold frequency tuner, and a 5 kW CW RF input coupler. A one-cavity test cryomodule has been assembled for a first full cryomodule test of the main linac cavity, and is currently under testing. In this paper we give an overview of these extensive R&D activities at Cornell.

WEPPC075

Testing of the Main-Linac Prototype Cavity in a Horizontal Test Cryomodule for the Cornell ERL

2387

N.R.A. Valles, F. Furuta, G.M. Ge, Y. He, K.M.V. Ho, G.H. Hoffstaetter, M. Liepe, T.I. O'Connell, S. Posen, P. Quigley, J. Sears, M. Tigner, V. Veshcherevich
CLASSE, Ithaca, New York, USA

Cornell has recently finished producing and testing the first prototype 7-cell main linac cavity for the Cornell Energy Recovery Linac (ERL). The cavity construction met all necessary fabrication constraints. After a bulk BCP, 650C outgassing, final BCP, and 120C bake the cavity was vertically tested. The cavity met quality factor and gradient specifications (2·10¹⁰ at 16.2 MV/m) in the vertical test. Progressing with the ERL linac development, the cavity was installed in a horizontal test cryomodule and the quality factor versus accelerating gradient was again measured. This baseline measurement is the first test in a sequence of tests of the main linac cavity in the test cryomodule. Subsequent tests will be with increased complexity of the beam line, e.g. with HOM beamline loads installed, to study potential sources of reducing the cavity’s quality factor.

WEPPD082

Characterization of Photocathode Damage during High Current Operation of the Cornell ERL Photoinjector

2717

J.M. Maxson, S.S. Karkare
Cornell University, Ithaca, New York, USA
I.V. Bazarov, S.A. Belomestnykh, L. Cultrera, D.S. Dale, J. Dobbins, B.M. Dunham, K. Finkelstein, R.P.K. Kaplan, V.O. Kostroun, Y. Li, X. Liu, F. Löhl, B. Pichler, P. Quigley, D.H. Rice, K.W. Smolenski, M. Tigner, V. Veshcherevich, Z. Zhao
CLASSE, Ithaca, New York, USA

The Cornell ERL Photoinjector prototype has recently demonstrated successful operation at 20 mA for 8 hours using a bi-alkali photocathode grown on a Si substrate. The photocathode film was grown off center, and remained relatively undamaged; however, upon removal from the gun, the substrate at the gun electrostatic center displayed significant visible damage. Here we will describe not only the parameters of that particular high current run, but a suite of post-operation surface morphology and crystallographic measurements, including X-ray fluorescence, X-ray diffraction, contact profilometry, scanning electron microscopy, performed about the damage site and photocathode film. The data indicate violent topological changes to the substrate surface, as well as significant induced crystallographic strain. Ion back-bombardment is proposed as a possible mechanism for damage, and a simple model for induced crystal strain is proposed (as opposed to ion induced sputtering), and is shown to have good qualitative agreement with the spatial distribution of damage.

Paper	Title	Page
MOOAA01	Performance of the Cornell High-Brightness, High-Power Electron Injector	20
	B.M. Dunham, A.C. Bartnik, I.V. Bazarov, L. Cultrera, J. Dobbins, C.M. Gulliford, G.H. Hoffstaetter, R.P.K. Kaplan, V.O. Kostroun, Y. Li, M. Liepe, X. Liu, F. Löhl, P. Quigley, D.H. Rice, E.N. Smith, K.W. Smolenski, M. Tigner, V. Veshcherevich, Z. Zhao CLASSE, Ithaca, New York, USA S.S. Karkare, H. Li, J.M. Maxson Cornell University, Ithaca, New York, USA
	Funding: NSF DMR-0807731 The last year has seen significant progress in demonstrating the feasibility of a high current, high brightness photoinjector as required for the Energy Recovery Linac driven X-ray source at Cornell University. Both low emittances (0.4 mm-mrad rms normalized for 100% of the beam at 20 pC per bunch and 0.15 mm-mrad rms core emittance with 70% of the beam, and twice these values at 80 pC per bunch) and high average currents with a good lifetime well in excess of 1000 Coulombs at 5 MeV, 20 mA have been demonstrated. If these beams can be accelerated to 5 GeV without diluting the phase space, it would already provide a beam brightness higher than any existing storage ring. Operational experience, results, and the outlook for the future will be presented.
	Slides MOOAA01 [1.424 MB]

WEPPC072	High Current Operation of the Cornell ERL Superconducting RF Injector Cryomodule	2378
	M. Liepe, G.H. Hoffstaetter, S. Posen, P. Quigley, V. Veshcherevich CLASSE, Ithaca, New York, USA
	Cornell University has developed a SCRF injector cryomodule for the acceleration of high current, low emittance beams in continuous wave operation. This cryomodule is based on superconducting RF technology, and is currently under extensive testing in the Cornell ERL injector prototype with CW beam currents exceeding 25 mA. Strong damping of Higher-Order-Modes in the cavities is essential for high beam current operation, and is achieved by beamline RF absorber located at cryogenic temperatures in the beam pipe sections between the cavities. This paper gives an overview of the experience gained during the high beam current operation of the cryomodule.

WEPPC031	Completed Assembly of the Daresbury International ERL Cryomodule and its Implementation on ALICE	2272
	P.A. McIntosh, M.A. Cordwell, P.A. Corlett, P. Davies, E. Frangleton, P. Goudket, K.J. Middleman, S.M. Pattalwar, A.E. Wheelhouse STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom S.A. Belomestnykh BNL, Upton, Long Island, New York, USA A. Büchner, F.G. Gabriel, P. Michel HZDR, Dresden, Germany J.N. Corlett, D. Li, S.M. Lidia LBNL, Berkeley, California, USA G.H. Hoffstaetter, M. Liepe, H. Padamsee, P. Quigley, J. Sears, V.D. Shemelin, V. Veshcherevich CLASSE, Ithaca, New York, USA T.J. Jones, J. Strachan STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom R.E. Laxdal TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada D. Proch, J.K. Sekutowicz DESY, Hamburg, Germany T.I. Smith Stanford University, Stanford, California, USA
	The completion of an optimised SRF cryomodule for application on ERL accelerators has now culminated with the successful assembly of an integrated cryomodule, following an intensive 5 years of development evolution. The cryomodule, which incorporates 2 x 7-cell 1.3 GHz accelerating structures, 3 separate layers of magnetic shielding, fully adjustable & high power input couplers and fast piezo tuners, has been installed on the ALICE ERL facility at Daresbury Laboratory. It is intended that this will permit operational optimisation for maximised efficiency demonstration, through increased Qext adjustment whilst retaining both effective energy recovery and IR-FEL lasing. The collaborative design processes employed in completing this new cryomodule development are explained, along with the assembly and implementation procedures used to facilitate its successful installation on the ALICE ERL facility.

WEPPC073	Progress on Superconducting RF Work for the Cornell ERL	2381
	M. Liepe, F. Furuta, G.M. Ge, Y. He, G.H. Hoffstaetter, T.I. O'Connell, S. Posen, J. Sears, M. Tigner, N.R.A. Valles, V. Veshcherevich CLASSE, Ithaca, New York, USA
	Cornell University is developing the superconducting RF technology required for the construction of a 100 mA hard X-ray light source driven by an Energy-Recovery Linac. Prototypes of all beam line components of the 5 GeV cw SRF main linac cryomodule have been fabricated and tested in detail. This work includes an optimized 7-cell SRF cavity, a broadband HOM beamline absorber, a cold frequency tuner, and a 5 kW CW RF input coupler. A one-cavity test cryomodule has been assembled for a first full cryomodule test of the main linac cavity, and is currently under testing. In this paper we give an overview of these extensive R&D activities at Cornell.

WEPPC075	Testing of the Main-Linac Prototype Cavity in a Horizontal Test Cryomodule for the Cornell ERL	2387
	N.R.A. Valles, F. Furuta, G.M. Ge, Y. He, K.M.V. Ho, G.H. Hoffstaetter, M. Liepe, T.I. O'Connell, S. Posen, P. Quigley, J. Sears, M. Tigner, V. Veshcherevich CLASSE, Ithaca, New York, USA
	Cornell has recently finished producing and testing the first prototype 7-cell main linac cavity for the Cornell Energy Recovery Linac (ERL). The cavity construction met all necessary fabrication constraints. After a bulk BCP, 650C outgassing, final BCP, and 120C bake the cavity was vertically tested. The cavity met quality factor and gradient specifications (2·10¹⁰ at 16.2 MV/m) in the vertical test. Progressing with the ERL linac development, the cavity was installed in a horizontal test cryomodule and the quality factor versus accelerating gradient was again measured. This baseline measurement is the first test in a sequence of tests of the main linac cavity in the test cryomodule. Subsequent tests will be with increased complexity of the beam line, e.g. with HOM beamline loads installed, to study potential sources of reducing the cavity’s quality factor.

WEPPD082	Characterization of Photocathode Damage during High Current Operation of the Cornell ERL Photoinjector	2717
	J.M. Maxson, S.S. Karkare Cornell University, Ithaca, New York, USA I.V. Bazarov, S.A. Belomestnykh, L. Cultrera, D.S. Dale, J. Dobbins, B.M. Dunham, K. Finkelstein, R.P.K. Kaplan, V.O. Kostroun, Y. Li, X. Liu, F. Löhl, B. Pichler, P. Quigley, D.H. Rice, K.W. Smolenski, M. Tigner, V. Veshcherevich, Z. Zhao CLASSE, Ithaca, New York, USA
	The Cornell ERL Photoinjector prototype has recently demonstrated successful operation at 20 mA for 8 hours using a bi-alkali photocathode grown on a Si substrate. The photocathode film was grown off center, and remained relatively undamaged; however, upon removal from the gun, the substrate at the gun electrostatic center displayed significant visible damage. Here we will describe not only the parameters of that particular high current run, but a suite of post-operation surface morphology and crystallographic measurements, including X-ray fluorescence, X-ray diffraction, contact profilometry, scanning electron microscopy, performed about the damage site and photocathode film. The data indicate violent topological changes to the substrate surface, as well as significant induced crystallographic strain. Ion back-bombardment is proposed as a possible mechanism for damage, and a simple model for induced crystal strain is proposed (as opposed to ion induced sputtering), and is shown to have good qualitative agreement with the spatial distribution of damage.