Author: Park, S.J.
Paper Title Page
TUPPP060 Injector Design for PAL-XFEL Project 1732
 
  • J.H. Han, M.S. Chae, J.H. Hong, I. Hwang, H.-S. Kang, I.S. Ko, S.J. Park
    PAL, Pohang, Kyungbuk, Republic of Korea
 
  Funding: The Ministry of Education, Science and Technology of the Korean Government
The PAL-XFEL project has the baseline specification of FEL radiation down to 0.1 nm with a 10 GeV S-band normal conducting linac. To fulfill the requirement of the beam parameter, the S-band photoinjector was designed. Numerical optimizations for nominal and low charge operations are presented.
 
 
TUOBB02 Commissioning of the PLS-II 1089
 
  • S. Shin, J.Y. Choi, T. Ha, J.Y. Huang, I. Hwang, W.H. Hwang, Y.D. Joo, C. Kim, D.T. Kim, D.E. Kim, J.M. Kim, M. Kim, S.H. Kim, S.-C. Kim, S.J. Kwon, B.-J. Lee, E.H. Lee, H.-S. Lee, H.M. Lee, J.W. Lee, S.H. Nam, E.S. Park, I.S. Park, S.S. Park, S.J. Park, Y.G. Son, J.C. Yoon
    PAL, Pohang, Kyungbuk, Republic of Korea
  • J-Y. Kim, B.H. Oh
    KAERI, Daejon, Republic of Korea
  • J. Lee
    POSTECH, Pohang, Kyungbuk, Republic of Korea
 
  The Pohang Light Source (PLS) has operated for 14 years successfully. To meet the request of the increasing user community, the PLS-II that is the upgrade project of PLS has been completed. Main goals of the PLS-II are to increase beam energy to 3 GeV, to increase number of insertion devices by the factor of two (20 IDs), to increase beam current to 400 mA and to reduce beam emittance below 10 nm with existing PLS tunnel and injection system. The PLS-II had been commissioned over the six months. During commissioning, we achieved 14 insertion devices operation and top-up operation with 100 mA beam current and 5.8 nm beam emittance. In this presentation, we report the experimental results from the PLS-II commissioning.  
slides icon Slides TUOBB02 [3.484 MB]  
 
TUPPD061 High-Power RF Test of an RF-Gun for PAL-XFEL 1539
 
  • J.H. Hong, J.H. Han, H.-S. Kang, C. Kim, S.H. Kim, C.-K. Min, S.S. Park, S.J. Park, Y.J. Park
    PAL, Pohang, Kyungbuk, Republic of Korea
  • M.S. Chae, I.S. Ko, Y.W. Parc
    POSTECH, Pohang, Kyungbuk, Republic of Korea
 
  A photocathode RF-gun for the X-ray free electron laser (XFEL) at the Pohang Accelerator Laboratory (PAL) has been fabricated and tested at PAL. This RF-gun is based on a 1.6-cell cavity with dual-feed waveguide ports and two pumping ports. The RF gun was designed by PAL and POSTECH. The RF-gun has been successfully tested with a cathode electric field gradient up to 126MV/m at a repetition rate of 30 Hz. This paper reports the recent results on the beam test of the RF-gun with high power RF at the gun test facility. We present and discuss the measurements of the basic beam parameters such as charge, energy, energy spread, and transverse emittance.  
 
WEPPD069 PLS-II Linac Upgrade 2681
 
  • B.-J. Lee, J.Y. Choi, S. Chunjarean, T. Ha, J.Y. Huang, I. Hwang, Y.D. Joo, C. Kim, M. Kim, S.H. Kim, S.J. Kwon, S.H. Nam, S.S. Park, S.J. Park, S. Shin, Y.G. Son
    PAL, Pohang, Kyungbuk, Republic of Korea
 
  This paper reports on the recent status of the Pohang Light Source (PLS)-II linac at Pohang Accelerator Laboratory (PAL). From 2009, the linac upgrade has been started increasing its energy from 2.5 GeV to 3 GeV aiming stable top-up mode operation. First, we show that the stability status of the two different types of modulators to meet the top-up condition which requires very stable modulator system in linac. Next, we introduce upgrade status those differ from their PLS (2.5 GeV) such as installation of the dual vacuum systems for the electron gun to replace it immediately, adding important diagnostic tools, and reutilization of the beam analysis system just after pre-injector. Finally we present the electron beam parameters measured by those diagnostic system.  
 
THPPC016 PLSII Linac RF Conditioning Status 3311
 
  • H.-S. Lee, J.Y. Huang, W.H. Hwang, H.-G. Kim, K.R. Kim, S.H. Kim, S.H. Kim, S.H. Nam, W. Namkung, S.S. Park, S.J. Park, Y.J. Park, S. Shin
    PAL, Pohang, Kyungbuk, Republic of Korea
 
  PLS linac has been upgraded in energy from 2.5 to 3.0 GeV. A klystron supplies RF power of 80 MW four acceleration structures through a SLED. But our machine is not enough RF power to get 3 GeV beam energy. So we have changed the RF scheme in four modules as a klystron supplies RF power of 80 MW two accelerating structures through a SLED. There were several problems during the RF conditioning and beam operation. So we will describe the conditioning results and the current status in this paper.  
 
TUPPC026 Design of Compact C-Band Standing-Wave Accelerating Structure Enhancing RF Phase Focusing 1221
 
  • H.R. Yang, M.-H. Cho, J. Jang, S.H. Kim, W. Namkung, S.J. Park
    POSTECH, Pohang, Kyungbuk, Republic of Korea
  • J.-S. Oh
    NFRI, Daejon, Republic of Korea
 
  Funding: Work supported by POSTECH Physics BK21 Program.
We design a C-band standing-wave accelerating structure for an X-ray source of the imaging and medical applications. It is capable of producing 6-MeV, 100-mA pulsed electron beams which is focused by less than 1.5 mm without external magnets. As an RF source, we use peak 1.5-MW magnetron with duty factor of 0.08%. The accelerating structure is a bi-periodic and on-axis-coupled structure with a built-in bunching section, which consists 3 bunching cells, 13 normal cells and a coupler cell. It operated with π/2-mode standing-waves. The bunching section is designed to enhance the RF phase focusing in order to achieve 1.2-mm beam spot size. Each cavity is designed with the MWS code to maximize the effective shunt impedance within 3.5% inter-cell coupling. In this paper, we present design details of RF cavities and the beam dynamics simulation by the PARMELA code.