IPAC2018 - List of Authors (Perillo-Marcone, A.)

Paper	Title	Page
MOPMF062	Upgrade of the Dilution System for HL-LHC	261
	C. Wiesner, W. Bartmann, C. Bracco, M. Calviani, E. Carlier, L. Ducimetière, M.I. Frankl, M.A. Fraser, S.S. Gilardoni, B. Goddard, T. Kramer, A. Lechner, N. Magnin, A. Perillo-Marcone, T. Polzin, E. Renner, V. Senaj CERN, Geneva, Switzerland
	The LHC Beam Dump System is one of the most critical systems for reliable and safe operation of the LHC. A dedicated dilution system is required to sweep the beam over the front face of the graphite dump core in order to reduce the deposited energy density. The High Luminosity Large Hadron Collider (HL-LHC) project foresees to increase the total beam intensity in the ring by nearly a factor of two, resulting in a correspondingly higher energy deposition in the dump core. In this paper, the beam sweep pattern and energy deposition for the case of normal dilution as well as for the relevant failure cases are presented. The implications as well as possible mitigations and upgrade measures for the dilution system, such as decreasing the pulse-generator voltage, adding two additional kickers, and implementing a retrigger system, are discussed.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-MOPMF062
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAF038	Prototyping Activities for a New Design of CERN's Antiproton Production Target	772
	C. Torregrosa, M.E.J. Butcher, M. Calviani, J.P.C. Espadanal, R. Ferriere, L. Gentini, E. Grenier-Boley, L. Mircea Grec, A. Perillo-Marcone, R. Seidenbinder, N.S. Solieri, M.A. Timmins, E. Urrutia, V. Vlachoudis CERN, Geneva, Switzerland
	Antiprotons are produced at CERN by impacting intense proton beams of 26 GeV/c onto a high-Z water-cooled target. The current design consists in an Ir core target in a graphite matrix and inserted in a Ti-6Al-4V assembly. A new target design has been foreseen for operation after 2021 aiming at improving the operation robustness and antiproton production yield, triggering several R&D activities during the last years. First, both numerical (use of hydrocodes) and experimental approaches were carried out to study the core material response under extreme dynamic loading when impacted by the primary proton beam. The lessons learnt from these studies have been then applied to further prototyping and testing under proton beam impact at the CERN-HiRadMat facility. A first scaled prototype consisting in Ta rods embedded in an expanded graphite matrix was irradiated in 2017, while in 2018, the PROTAD experiment will test different real-scale AD-Target prototypes, in which the old water-cooled assembly is replaced by a more compact air-cooled one, and different core geometry and material configurations are investigated. This contribution details these prototyping and testing activities.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPAF038
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMF084	Design, Prototyping Activities and Beam Irradiation Test for the New n_TOF Neutron Spallation Target	2582
	R. Esposito, M. Bergeret, J. Busom, M.E.J. Butcher, M. Calviani, R. Cimmino, T. Coiffet, J.P.C. Espadanal, L. Gentini, R. Illan Fiastre, V. Maire, F. Ogallar Ruiz, A. Perillo-Marcone, S. Sgobba, M.A. Timmins, C. Torregrosa, E. Urrutia, V. Vlachoudis CERN, Geneva, Switzerland R. Logé EPFL, Lausanne, Switzerland
	A third-generation neutron spallation target for the neutron time-of-flight facility at CERN (n_TOF) is currently undergoing the design and prototyping stage. The new design aims at improving reliability, increasing beam intensity on target and avoiding issues encountered in the current generation target, in particular the contamination of the cooling system water with radioactive spallation products coming from washing out lead. After a preliminary design and an initial prototyping stage, a baseline solution has been defined consisting in a pure lead target core contained in a Ti-6Al-4V cladding and embedded in a massive Pb block. A backup solution has also been defined, consisting in a Ta-cladded W core embedded in a Pb block. Both solutions are currently undergoing the detailed design stage. This contribution details the prototyping activity, the robustness studies for accidental scenarios and the design of a beam irradiation test on prototypes of the target core. R. Esposito et al., "Design of the new CERN n_TOF neutron spallation target: R&D and prototyping activities," in Proc. of IPAC'17, Copenhagen, May 2017.*
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMF084
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMG003	Analysis and Operational Feedback of the New High-Energy Beam Dump in the CERN SPS	2608
	A. Perillo-Marcone, M. Calviani, R. Illan Fiastre, P. Rios Rodriguez, G. Romagnoli CERN, Geneva, Switzerland
	The CERN Super Proton Synchrotron (SPS) high-energy internal dump (TIDVG) is used to intercept beam dumps from 10².2 to 450 GeV. An inspection in 2013 revealed significant beam induced damage to the aluminium absorbing block, resulting in operational limitations to minimize the risk of reproducing this phenomenon. Additionally, in 2016 a vacuum leak was detected in the dump assembly, which imposed further limitations, i.e., a reduction of the beam intensity that could be dumped. In the winter stop of 2016-2017, a new version of the TIDVG (featuring several design modifications) was installed. This paper analyses the performance of the dump observed during the commissioning period and subsequent operation in 2017 of the most recent installed version of the TIDVG. The temperature measurements recorded during this time were used to benchmark numerical models that allow predicting the performance of the dump under different conditions. After several iterations, a good agreement between simulations and real measurements was obtained; resulting in numerical models that can produce reliable results for this and other devices with similar design.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMG003
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMG004	Design of the Future High Energy Beam Dump for the CERN SPS	2612
	S. Pianese, J.A. Briz Monago, M. Calviani, D. Grenier, P.B. Heckmann, J. Humbert, R. Illan Fiastre, A. Perillo-Marcone, G. Romagnoli, S. Sgobba, D. Steyart, V. Vlachoudis CERN, Geneva, Switzerland
	The future CERN Super Proton Synchrotron (SPS) internal dump (Target Internal Dump Vertical Graphite, known as TIDVG#5), to be installed during CERN's Long Shutdown 2 (2019-2020), will be required to intercept beam dumps from 26 to 450 GeV, with increased intensity and repetition rates with respect to its predecessor (TIDVG#4). The beam power to be managed by the dump will increase by approximately a factor of four; resulting in new challenges in terms of design in order to fulfil the highly demanding specification, which is based on guaranteeing a good performance of the machine with little or no limitations imposed by this device. This paper presents the proposed design, including material selection, manufacturing techniques and thermo-mechanical simulations under different operational scenarios expected during the lifetime of the device.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMG004
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAK092	Analysis on the Mechanical Effects Induced by Beam Impedance Heating on the HL-LHC Target Dump Injection Segmented (TDIS) Absorber	3448
	L. Teofili, M. Migliorati Sapienza University of Rome, Rome, Italy M. Calviani, D. Carbajo Perez, S.S. Gilardoni, F. Giordano, I. Lamas Garcia, G. Mazzacano, A. Perillo-Marcone CERN, Geneva, Switzerland
	The High Luminosity Large Hadron Collider (HL-LHC) Project at CERN calls for increasing beam brightness and intensity. In such a scenario, critical accelerator devices need to be redesigned and rebuilt. Impedance is among the design drivers, since its thermo-mechanical effects could lead to premature device failures. In this context, the current work reports the results of a multiphysics study to assess the electromagnetic and thermo-mechanical behaviour of the Target Dump Injection Segmented (TDIS). It first discusses the outcomes of the impedance analysis performed to characterise the resistive wall and the high order resonant modes (HOMs) trapped in the TDIS structures. Then, their RF-heating effects and the related temperature distribution are considered. Finally, mechanical stresses induced by thermal gradients are studied in order to give a final validation on the design quality.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAK092
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Upgrade of the Dilution System for HL-LHC

261

C. Wiesner, W. Bartmann, C. Bracco, M. Calviani, E. Carlier, L. Ducimetière, M.I. Frankl, M.A. Fraser, S.S. Gilardoni, B. Goddard, T. Kramer, A. Lechner, N. Magnin, A. Perillo-Marcone, T. Polzin, E. Renner, V. Senaj
CERN, Geneva, Switzerland

The LHC Beam Dump System is one of the most critical systems for reliable and safe operation of the LHC. A dedicated dilution system is required to sweep the beam over the front face of the graphite dump core in order to reduce the deposited energy density. The High Luminosity Large Hadron Collider (HL-LHC) project foresees to increase the total beam intensity in the ring by nearly a factor of two, resulting in a correspondingly higher energy deposition in the dump core. In this paper, the beam sweep pattern and energy deposition for the case of normal dilution as well as for the relevant failure cases are presented. The implications as well as possible mitigations and upgrade measures for the dilution system, such as decreasing the pulse-generator voltage, adding two additional kickers, and implementing a retrigger system, are discussed.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-MOPMF062

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPAF038

Prototyping Activities for a New Design of CERN's Antiproton Production Target

772

C. Torregrosa, M.E.J. Butcher, M. Calviani, J.P.C. Espadanal, R. Ferriere, L. Gentini, E. Grenier-Boley, L. Mircea Grec, A. Perillo-Marcone, R. Seidenbinder, N.S. Solieri, M.A. Timmins, E. Urrutia, V. Vlachoudis
CERN, Geneva, Switzerland

Antiprotons are produced at CERN by impacting intense proton beams of 26 GeV/c onto a high-Z water-cooled target. The current design consists in an Ir core target in a graphite matrix and inserted in a Ti-6Al-4V assembly. A new target design has been foreseen for operation after 2021 aiming at improving the operation robustness and antiproton production yield, triggering several R&D activities during the last years. First, both numerical (use of hydrocodes) and experimental approaches were carried out to study the core material response under extreme dynamic loading when impacted by the primary proton beam. The lessons learnt from these studies have been then applied to further prototyping and testing under proton beam impact at the CERN-HiRadMat facility. A first scaled prototype consisting in Ta rods embedded in an expanded graphite matrix was irradiated in 2017, while in 2018, the PROTAD experiment will test different real-scale AD-Target prototypes, in which the old water-cooled assembly is replaced by a more compact air-cooled one, and different core geometry and material configurations are investigated. This contribution details these prototyping and testing activities.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPAF038

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMF084

Design, Prototyping Activities and Beam Irradiation Test for the New n_TOF Neutron Spallation Target

2582

R. Esposito, M. Bergeret, J. Busom, M.E.J. Butcher, M. Calviani, R. Cimmino, T. Coiffet, J.P.C. Espadanal, L. Gentini, R. Illan Fiastre, V. Maire, F. Ogallar Ruiz, A. Perillo-Marcone, S. Sgobba, M.A. Timmins, C. Torregrosa, E. Urrutia, V. Vlachoudis
CERN, Geneva, Switzerland
R. Logé
EPFL, Lausanne, Switzerland

A third-generation neutron spallation target for the neutron time-of-flight facility at CERN (n_TOF) is currently undergoing the design and prototyping stage. The new design aims at improving reliability, increasing beam intensity on target and avoiding issues encountered in the current generation target, in particular the contamination of the cooling system water with radioactive spallation products coming from washing out lead. After a preliminary design and an initial prototyping stage*, a baseline solution has been defined consisting in a pure lead target core contained in a Ti-6Al-4V cladding and embedded in a massive Pb block. A backup solution has also been defined, consisting in a Ta-cladded W core embedded in a Pb block. Both solutions are currently undergoing the detailed design stage. This contribution details the prototyping activity, the robustness studies for accidental scenarios and the design of a beam irradiation test on prototypes of the target core.
R. Esposito et al., "Design of the new CERN n_TOF neutron spallation target: R&D and prototyping activities," in Proc. of IPAC'17, Copenhagen, May 2017.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMF084

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMG003

Analysis and Operational Feedback of the New High-Energy Beam Dump in the CERN SPS

2608

A. Perillo-Marcone, M. Calviani, R. Illan Fiastre, P. Rios Rodriguez, G. Romagnoli
CERN, Geneva, Switzerland

The CERN Super Proton Synchrotron (SPS) high-energy internal dump (TIDVG) is used to intercept beam dumps from 10².2 to 450 GeV. An inspection in 2013 revealed significant beam induced damage to the aluminium absorbing block, resulting in operational limitations to minimize the risk of reproducing this phenomenon. Additionally, in 2016 a vacuum leak was detected in the dump assembly, which imposed further limitations, i.e., a reduction of the beam intensity that could be dumped. In the winter stop of 2016-2017, a new version of the TIDVG (featuring several design modifications) was installed. This paper analyses the performance of the dump observed during the commissioning period and subsequent operation in 2017 of the most recent installed version of the TIDVG. The temperature measurements recorded during this time were used to benchmark numerical models that allow predicting the performance of the dump under different conditions. After several iterations, a good agreement between simulations and real measurements was obtained; resulting in numerical models that can produce reliable results for this and other devices with similar design.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMG003

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMG004

Design of the Future High Energy Beam Dump for the CERN SPS

2612

S. Pianese, J.A. Briz Monago, M. Calviani, D. Grenier, P.B. Heckmann, J. Humbert, R. Illan Fiastre, A. Perillo-Marcone, G. Romagnoli, S. Sgobba, D. Steyart, V. Vlachoudis
CERN, Geneva, Switzerland

The future CERN Super Proton Synchrotron (SPS) internal dump (Target Internal Dump Vertical Graphite, known as TIDVG#5), to be installed during CERN's Long Shutdown 2 (2019-2020), will be required to intercept beam dumps from 26 to 450 GeV, with increased intensity and repetition rates with respect to its predecessor (TIDVG#4). The beam power to be managed by the dump will increase by approximately a factor of four; resulting in new challenges in terms of design in order to fulfil the highly demanding specification, which is based on guaranteeing a good performance of the machine with little or no limitations imposed by this device. This paper presents the proposed design, including material selection, manufacturing techniques and thermo-mechanical simulations under different operational scenarios expected during the lifetime of the device.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMG004

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAK092

Analysis on the Mechanical Effects Induced by Beam Impedance Heating on the HL-LHC Target Dump Injection Segmented (TDIS) Absorber

3448

L. Teofili, M. Migliorati
Sapienza University of Rome, Rome, Italy
M. Calviani, D. Carbajo Perez, S.S. Gilardoni, F. Giordano, I. Lamas Garcia, G. Mazzacano, A. Perillo-Marcone
CERN, Geneva, Switzerland

The High Luminosity Large Hadron Collider (HL-LHC) Project at CERN calls for increasing beam brightness and intensity. In such a scenario, critical accelerator devices need to be redesigned and rebuilt. Impedance is among the design drivers, since its thermo-mechanical effects could lead to premature device failures. In this context, the current work reports the results of a multiphysics study to assess the electromagnetic and thermo-mechanical behaviour of the Target Dump Injection Segmented (TDIS). It first discusses the outcomes of the impedance analysis performed to characterise the resistive wall and the high order resonant modes (HOMs) trapped in the TDIS structures. Then, their RF-heating effects and the related temperature distribution are considered. Finally, mechanical stresses induced by thermal gradients are studied in order to give a final validation on the design quality.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAK092

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)