SRF2017 - List of Authors (Asensi Conejero, E.)

Paper	Title	Page
MOPB018	Testing of SRF Cavities and Cryomodules for the European Spallation Source	95
	N. Elias, E. Asensi Conejero, C. Darve, N.F. Hakansson, W. Hees, C.G. Maiano, F. Schlander ESS, Lund, Sweden
	The European Spallation Source (ESS) is currently under construction in Lund, Sweden. The ESS linear accelerator aims to deliver a 62.5 mA , 2.86 ms long proton beam onto a rotating tungsten target, at 14 Hz repetition rate, thus achieving an energy of 2 GeV and 5 MW power. Most of the beam acceleration happens in the superconducting fraction of the linac, which is composed of three sectors of cryomodules named after the cavities housed within. The first sector of the SRF linac is composed of 13 Spoke cryomodules containing 2 double-spoke cavities with a geometric beta of 0.5, the second is composed of 9 medium beta cryomodules each housing four elliptical cavities (β=0.67) and finally 21 high beta cryomodules enclosing four elliptical cavities (β=0.86). ESS has strategically built up a SRF collaboration with other European institutions, these partners will deliver through In-Kind agreements cavities and cryomodules performing within the ESS specification. This article describes the process leading to the acceptance of cavities and cryomodules received from the different partners and the necessary testing required prior to the final installation in the ESS tunnel.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2017-MOPB018
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPB020	An Optimal Procedure for Coupler Conditioning for ESS Superconducting Linac	103
	H. Li Uppsala University, Uppsala, Sweden E. Asensi Conejero, C.G. Maiano, R. Zeng ESS, Lund, Sweden
	An optimal procedure for coupler and cavity conditioning is proposed for the ESS superconducting cavities, which is applicable for different test stands and following installation in the ESS tunnel. A preliminary procedure has been developed and successfully tested at FREIA facility, Uppsala. The preliminary procedure will now be improved by integrating it into LLRF and EPICS control. This will be a joint effort between FREIA and ESS and will be used at the test stands in Lund and on the couplers installed in the tunnel. Developing the conditioning procedures on a common platform offers ESS significant advantages by allowing the procedures to be reused at different sites and by recording data in a consistent format. The details of the procedure, its development and testing will be reported and the future activities will be described.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2017-MOPB020
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Testing of SRF Cavities and Cryomodules for the European Spallation Source

95

N. Elias, E. Asensi Conejero, C. Darve, N.F. Hakansson, W. Hees, C.G. Maiano, F. Schlander
ESS, Lund, Sweden

The European Spallation Source (ESS) is currently under construction in Lund, Sweden. The ESS linear accelerator aims to deliver a 62.5 mA , 2.86 ms long proton beam onto a rotating tungsten target, at 14 Hz repetition rate, thus achieving an energy of 2 GeV and 5 MW power. Most of the beam acceleration happens in the superconducting fraction of the linac, which is composed of three sectors of cryomodules named after the cavities housed within. The first sector of the SRF linac is composed of 13 Spoke cryomodules containing 2 double-spoke cavities with a geometric beta of 0.5, the second is composed of 9 medium beta cryomodules each housing four elliptical cavities (β=0.67) and finally 21 high beta cryomodules enclosing four elliptical cavities (β=0.86). ESS has strategically built up a SRF collaboration with other European institutions, these partners will deliver through In-Kind agreements cavities and cryomodules performing within the ESS specification. This article describes the process leading to the acceptance of cavities and cryomodules received from the different partners and the necessary testing required prior to the final installation in the ESS tunnel.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2017-MOPB018

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPB020

An Optimal Procedure for Coupler Conditioning for ESS Superconducting Linac

103

H. Li
Uppsala University, Uppsala, Sweden
E. Asensi Conejero, C.G. Maiano, R. Zeng
ESS, Lund, Sweden

An optimal procedure for coupler and cavity conditioning is proposed for the ESS superconducting cavities, which is applicable for different test stands and following installation in the ESS tunnel. A preliminary procedure has been developed and successfully tested at FREIA facility, Uppsala. The preliminary procedure will now be improved by integrating it into LLRF and EPICS control. This will be a joint effort between FREIA and ESS and will be used at the test stands in Lund and on the couplers installed in the tunnel. Developing the conditioning procedures on a common platform offers ESS significant advantages by allowing the procedures to be reused at different sites and by recording data in a consistent format. The details of the procedure, its development and testing will be reported and the future activities will be described.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2017-MOPB020

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)