RuPAC2021 - List of Authors (Telnov, A.V.)

Paper	Title	Page
MOPSA02	Experimental Tests of CW Resonance Accelerator With 7.5 MeV High Intensity Electron Beam	132
	L.E. Polyakov, Ya.V. Bodryashkin, M.A. Guzov, I.I. Konishev, N.N. Kurapov, V.V. Kuznetsov, I.A. Mashin, V.R. Nikolaev, A.M. Opekunov, G. Pospelov, A.N. Shein, I.V. Shorikov, N.V. Zavyalov, I.V. Zhukov RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia S.A. Putevskoy, M.L. Smetanin, A.V. Telnov VNIIEF, Sarov, Russia
	CW resonance accelerator with high average power electron beam is developed at RFNC-VNIIEF. Electron energy range is varied from 1.5 to 7.5 MeV and average beam current is up to 40 mA. Electrons obtain the required energy by several passing of coaxial half-wave accelerating cavity. In this paper we present the results of electron beam dynamics simulation during its acceleration and transportation. The operating parameters of RF system, beam optics and bending magnets are determined. These parameters permit to obtain output beam with minimal current losses on each accelerating stage. As a result of carried out tests we obtained 7.5 MeV electron beam after five passes of accelerating cavity. The electron energy spectrum, average beam current, transverse beam dimensions were determined on each accelerating stage. Common beam current loss is under 10 %.
DOI •	reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-MOPSA02
About •	Received ※ 25 September 2021 — Revised ※ 26 September 2021 — Accepted ※ 07 October 2021 — Issued ※ 21 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPSA03	Calculations of Ion Dynamics and Elecrodynamics Characteristics of 800 KeV/nucleon RFQ	135
	M.A. Guzov, A.M. Opekunov, L.E. Polyakov, N.V. Zavyalov RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia M.A. Guzov, E.N. Indiushnii, Y. Lozeev, A.I. Makarov, S.M. Polozov MEPhI, Moscow, Russia M.L. Smetanin, A.V. Telnov VNIIEF, Sarov, Russia
	Accelerating structure with radio-frequency quadrupole focusing (RFQ) was observed in this research. The RFQ is aimed to bunch up, accelerate and focus 1 MeV/nucleon ions with A/Z from 1 to 3.2 (A - mass number of ion, Z - ion charge). The chemical elements from H⁺ to O5+ fill up this particle types range. The protons current is 2 mA and ion current is 1 mA. In this paper charged particle dynamics calculations, which essential for next electrodynamic cavity modeling, were performed. The electrodynamic model of 4-vane RFQ cavity with windows of magnetic connection was created. The dependence between frequency and cavity geometrics was defined. Topology of magnetic windows, which aimed to have the maximum mod separations, was determined. Different types of tanks were considered and corresponding electromagnetic characteristics were calculated. Tuning elements (plungers and spacers) influence on cavity was modeled. As a result optimized model of accelerating structure was realized.
DOI •	reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-MOPSA03
About •	Received ※ 20 September 2021 — Revised ※ 29 September 2021 — Accepted ※ 07 October 2021 — Issued ※ 18 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPSA54	Calculation of Dose Fields and Energy Spectra of Secondary Radiation in the Extraction Zone of a Synchrotron Accelerator for Protons With Energies Up to 700 MeV	222
	R.P. Truntseva, N.N. Kurapov, A.M. Opekunov RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia A.V. Telnov, N.V. Zavyalov VNIIEF, Sarov, Russia
	The possibility of using a multipurpose synchrotron accelerator for researching the processes of heavy charged particles interaction with various materials is considered. The accelerator provides proton energies up to 700 MeV. It is necessary to evaluate the emerging dose fields at the design stage of the experimental room. In this case, it is important to evaluate the dose distribution, energies and types of secondary radiation that may enter the adjacent rooms. This paper presents the results of the radiation environment evaluation in the radiation extraction zone of the synchrotron accelerator. Simulation results of secondary radiation energy spectra near the walls, which separate the irradiation zone from adjacent rooms, are presented. Proton energies are equal to 60, 85, 110 and 700 MeV are considered. Simulation was performed by the Monte Carlo method in a program developed using Geant4* libraries. * Geant4 User’s Guide for Application Developers //Geant4 Collaboration.
DOI •	reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-MOPSA54
About •	Received ※ 27 September 2021 — Revised ※ 28 September 2021 — Accepted ※ 09 October 2021 — Issued ※ 11 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUB07	The Conceptual Design of the 7.5 MeV/u Light Ion Injector	51
	S.M. Polozov, A.E. Aksentyev, M.M. Bulgacheva, O.V. Deryabochkin, M.S. Dmitriyev, V.V. Dmitriyeva, M.V. Dyakonov, V.S. Dyubkov, A.V. Gerasimenko, A.A. Gorchakov, M. Gusarova, M.A. Guzov, E.N. Indiushnii, A.M. Korshunov, K.I. Kozlovskiy, A.S. Krasnov, M.V. Lalayan, Y. Lozeev, T.A. Lozeeva, A.I. Makarov, S.V. Matsievskiy, A.P. Melekhov, O.V. Murygin, R.E. Nemchenko, G.G. Novikov, A.E. Novozhilov, A.S. Panishev, V.N. Pashentsev, A.G. Ponomarenko, A.V. Prokopenko, V.I. Rashchikov, A.V. Samoshin, A.A. Savchik, V.L. Shatokhin, A.E. Shikanov, K.D. Smirnov, G.A. Tsarev, S.A. Tumanov, I.A. Yurin, M.I. Zhigailova MEPhI, Moscow, Russia M.L. Smetanin, A.V. Telnov VNIIEF, Sarov, Russia N.V. Zavyalov RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia
	The new linac for light ion beam injection is under development at MEPhI. Such linac was proposed for acceleration of 7.5 MeV/u ion beam with A/Z=1-3 and current up to 5 mA for proton and 0.4 pmA for light ions. The linac general layout will include two types of ion sources: ECR ion source for proton anf He ions and laser ion source for ions form Li to O. Following the LEBT ions will be bunched and accelerated to the final energy using RFQ section and 14 IH cavities. These IH-cavities will be identical (divided into two groups) and independently phased. All cavities will operate on 81 MHz. Results of the beam dynamics simulations and the cavities design will presented in the report.
	Slides TUB07 [5.210 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-TUB07
About •	Received ※ 16 September 2021 — Revised ※ 25 September 2021 — Accepted ※ 27 September 2021 — Issued ※ 14 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPSB12	Development of a Program Code for Calculation of Charged Particle Dynamics in RFQ	256
	A.S. Boriskov, A.M. Opekunov, L.E. Polyakov, N.V. Zavyalov RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia M.L. Smetanin, A.V. Telnov VNIIEF, Sarov, Russia
	The calculation of charged particles dynamics is the initial stage in the development of an accelerator. The advancement of computer technology makes it possible to calculate particle dynamics using numerical methods with a required accuracy. During beam dynamics calculation it is necessary to take into account RF field force and self-induced Coulomb forces which also have an effect on charged particles. In this paper a model of «large particles» was chosen to simulate a space charge effect. To implement this model, a program code was written using parallel computing tools in the «C» programming language in the CUDA toolkit. The dynamics of ions with a ratio A / Z from 1 to 3.2 (A - the mass number, Z - the charge state of the ion) in the RFQ structure was calculated. The operating frequency of structure is 81.25 MHz, output energy is up to 820 keV / nucleon. Output beam characteristics (relative velocity, particle capture coefficient, beam profile, transverse emittances, longitudinal phase portrait) were determined. These results were verified by the BEAMDULAC-RFQ program. Polozov S. M., Prob. of Atomic Sci. and Tech., 3 (79), 2012, pp. 131-136.
DOI •	reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-TUPSB12
About •	Received ※ 30 September 2021 — Revised ※ 01 October 2021 — Accepted ※ 09 October 2021 — Issued ※ 14 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPSC04	Accelerating Structure of 8 MeV Electron Linac	346
	A.N. Shein, I.V. Shorikov RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia A.V. Telnov VNIIEF, Sarov, Russia
	Linear resonance electron accelerator LU-10-20 is under operation in RFNC-VNIIEF since 1994. LU-10-20 is aimed at carrying out radiation processing of materials and researching radiation processes. The energy of accelerated electrons is up to 10 MeV, the average beam power - up to 12 kW. This accelerator has demonstrated that it is highly useful for performing radiation researches and tests. As of today work is underway on modernization of LU-10-20 including its accelerating structure and RF power supply. Accelerating structure is aimed at electron beam acceleration up to nominal energy and consists of complicated resonance TW RF structure, which uncluded iris-loaded waveguide, input and output matching devices. The paper presents the electrodynamic calculation results of modernized accelerating structure, input and output matching devices, and also beam dynamics calculation results. N.V.Zavyalov et al. Commercial linear accelerator of electrons LU-10-20. Materials of the XV All-Union Seminar on Linear Accelerators of Charged Particles, Nucl. Phys. Res.No2, 3(29, 30),1997, p.39-41.
DOI •	reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-WEPSC04
About •	Received ※ 28 September 2021 — Revised ※ 29 September 2021 — Accepted ※ 09 October 2021 — Issued ※ 18 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPSC57	System of on-Line Energy Control of Electron Beam for Accelerator	446
	N.N. Kurapov, Ya.V. Bodryashkin, A.S. Cherkasov, I.V. Shorikov RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia A.V. Telnov VNIIEF, Sarov, Russia
	There arises a need for measuring the output electron energy in the on-line mode during set-up, adjustment or operation of an accelerator. For this purpose a system is developed, allowing an on-line control of an accelerated electron energy spectrum simultaneously with average current measurement. This system is meant for reconstruction of the energy spectrum of accelerated electrons in the energy range from 1 up to 10 MeV at the average beam current from 20 up to 150 µA. The system is based on the method of absorbing filters and consists of an assembly, absorbing an accelerated electron beam, and a measuring system. The absorption assembly represents a set of insulated from each other electro-conducting plates of dimension 100x100 mm and thickness from 0.15 up to 1 mm with an air gap between plates 2 mm. The operation involves development, manufacture and calculation of electron beam transmission through the absorption assembly, development and manufacture of hardware for automated measuring of absorbed charges in the assembly elements, development of a master computer program as well as a program of energy spectrum reconstruction, using measured and calculated data, testing of the energy on-line control system on the LU-10-20 linear resonance electron accelerator. Tests of the developed sample on the electron accelerator have proved the applicability of the system to control the electron beam energy in the real-time mode.
DOI •	reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-WEPSC57
About •	Received ※ 27 September 2021 — Revised ※ 30 September 2021 — Accepted ※ 09 October 2021 — Issued ※ 22 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Experimental Tests of CW Resonance Accelerator With 7.5 MeV High Intensity Electron Beam

132

L.E. Polyakov, Ya.V. Bodryashkin, M.A. Guzov, I.I. Konishev, N.N. Kurapov, V.V. Kuznetsov, I.A. Mashin, V.R. Nikolaev, A.M. Opekunov, G. Pospelov, A.N. Shein, I.V. Shorikov, N.V. Zavyalov, I.V. Zhukov
RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia
S.A. Putevskoy, M.L. Smetanin, A.V. Telnov
VNIIEF, Sarov, Russia

CW resonance accelerator with high average power electron beam is developed at RFNC-VNIIEF. Electron energy range is varied from 1.5 to 7.5 MeV and average beam current is up to 40 mA. Electrons obtain the required energy by several passing of coaxial half-wave accelerating cavity. In this paper we present the results of electron beam dynamics simulation during its acceleration and transportation. The operating parameters of RF system, beam optics and bending magnets are determined. These parameters permit to obtain output beam with minimal current losses on each accelerating stage. As a result of carried out tests we obtained 7.5 MeV electron beam after five passes of accelerating cavity. The electron energy spectrum, average beam current, transverse beam dimensions were determined on each accelerating stage. Common beam current loss is under 10 %.

DOI •

reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-MOPSA02

About •

Received ※ 25 September 2021 — Revised ※ 26 September 2021 — Accepted ※ 07 October 2021 — Issued ※ 21 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPSA03

Calculations of Ion Dynamics and Elecrodynamics Characteristics of 800 KeV/nucleon RFQ

135

M.A. Guzov, A.M. Opekunov, L.E. Polyakov, N.V. Zavyalov
RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia
M.A. Guzov, E.N. Indiushnii, Y. Lozeev, A.I. Makarov, S.M. Polozov
MEPhI, Moscow, Russia
M.L. Smetanin, A.V. Telnov
VNIIEF, Sarov, Russia

Accelerating structure with radio-frequency quadrupole focusing (RFQ) was observed in this research. The RFQ is aimed to bunch up, accelerate and focus 1 MeV/nucleon ions with A/Z from 1 to 3.2 (A - mass number of ion, Z - ion charge). The chemical elements from H⁺ to O5+ fill up this particle types range. The protons current is 2 mA and ion current is 1 mA. In this paper charged particle dynamics calculations, which essential for next electrodynamic cavity modeling, were performed. The electrodynamic model of 4-vane RFQ cavity with windows of magnetic connection was created. The dependence between frequency and cavity geometrics was defined. Topology of magnetic windows, which aimed to have the maximum mod separations, was determined. Different types of tanks were considered and corresponding electromagnetic characteristics were calculated. Tuning elements (plungers and spacers) influence on cavity was modeled. As a result optimized model of accelerating structure was realized.

DOI •

reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-MOPSA03

About •

Received ※ 20 September 2021 — Revised ※ 29 September 2021 — Accepted ※ 07 October 2021 — Issued ※ 18 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPSA54

Calculation of Dose Fields and Energy Spectra of Secondary Radiation in the Extraction Zone of a Synchrotron Accelerator for Protons With Energies Up to 700 MeV

222

R.P. Truntseva, N.N. Kurapov, A.M. Opekunov
RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia
A.V. Telnov, N.V. Zavyalov
VNIIEF, Sarov, Russia

The possibility of using a multipurpose synchrotron accelerator for researching the processes of heavy charged particles interaction with various materials is considered. The accelerator provides proton energies up to 700 MeV. It is necessary to evaluate the emerging dose fields at the design stage of the experimental room. In this case, it is important to evaluate the dose distribution, energies and types of secondary radiation that may enter the adjacent rooms. This paper presents the results of the radiation environment evaluation in the radiation extraction zone of the synchrotron accelerator. Simulation results of secondary radiation energy spectra near the walls, which separate the irradiation zone from adjacent rooms, are presented. Proton energies are equal to 60, 85, 110 and 700 MeV are considered. Simulation was performed by the Monte Carlo method in a program developed using Geant4* libraries.
* Geant4 User’s Guide for Application Developers //Geant4 Collaboration.

DOI •

reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-MOPSA54

About •

Received ※ 27 September 2021 — Revised ※ 28 September 2021 — Accepted ※ 09 October 2021 — Issued ※ 11 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUB07

The Conceptual Design of the 7.5 MeV/u Light Ion Injector

51

S.M. Polozov, A.E. Aksentyev, M.M. Bulgacheva, O.V. Deryabochkin, M.S. Dmitriyev, V.V. Dmitriyeva, M.V. Dyakonov, V.S. Dyubkov, A.V. Gerasimenko, A.A. Gorchakov, M. Gusarova, M.A. Guzov, E.N. Indiushnii, A.M. Korshunov, K.I. Kozlovskiy, A.S. Krasnov, M.V. Lalayan, Y. Lozeev, T.A. Lozeeva, A.I. Makarov, S.V. Matsievskiy, A.P. Melekhov, O.V. Murygin, R.E. Nemchenko, G.G. Novikov, A.E. Novozhilov, A.S. Panishev, V.N. Pashentsev, A.G. Ponomarenko, A.V. Prokopenko, V.I. Rashchikov, A.V. Samoshin, A.A. Savchik, V.L. Shatokhin, A.E. Shikanov, K.D. Smirnov, G.A. Tsarev, S.A. Tumanov, I.A. Yurin, M.I. Zhigailova
MEPhI, Moscow, Russia
M.L. Smetanin, A.V. Telnov
VNIIEF, Sarov, Russia
N.V. Zavyalov
RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia

The new linac for light ion beam injection is under development at MEPhI. Such linac was proposed for acceleration of 7.5 MeV/u ion beam with A/Z=1-3 and current up to 5 mA for proton and 0.4 pmA for light ions. The linac general layout will include two types of ion sources: ECR ion source for proton anf He ions and laser ion source for ions form Li to O. Following the LEBT ions will be bunched and accelerated to the final energy using RFQ section and 14 IH cavities. These IH-cavities will be identical (divided into two groups) and independently phased. All cavities will operate on 81 MHz. Results of the beam dynamics simulations and the cavities design will presented in the report.

Slides TUB07 [5.210 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-TUB07

About •

Received ※ 16 September 2021 — Revised ※ 25 September 2021 — Accepted ※ 27 September 2021 — Issued ※ 14 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPSB12

Development of a Program Code for Calculation of Charged Particle Dynamics in RFQ

256

A.S. Boriskov, A.M. Opekunov, L.E. Polyakov, N.V. Zavyalov
RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia
M.L. Smetanin, A.V. Telnov
VNIIEF, Sarov, Russia

The calculation of charged particles dynamics is the initial stage in the development of an accelerator. The advancement of computer technology makes it possible to calculate particle dynamics using numerical methods with a required accuracy. During beam dynamics calculation it is necessary to take into account RF field force and self-induced Coulomb forces which also have an effect on charged particles. In this paper a model of «large particles» was chosen to simulate a space charge effect. To implement this model, a program code was written using parallel computing tools in the «C» programming language in the CUDA toolkit. The dynamics of ions with a ratio A / Z from 1 to 3.2 (A - the mass number, Z - the charge state of the ion) in the RFQ structure was calculated. The operating frequency of structure is 81.25 MHz, output energy is up to 820 keV / nucleon. Output beam characteristics (relative velocity, particle capture coefficient, beam profile, transverse emittances, longitudinal phase portrait) were determined. These results were verified by the BEAMDULAC-RFQ program*.
* Polozov S. M., Prob. of Atomic Sci. and Tech., 3 (79), 2012, pp. 131-136.

DOI •

reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-TUPSB12

About •

Received ※ 30 September 2021 — Revised ※ 01 October 2021 — Accepted ※ 09 October 2021 — Issued ※ 14 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPSC04

Accelerating Structure of 8 MeV Electron Linac

346

A.N. Shein, I.V. Shorikov
RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia
A.V. Telnov
VNIIEF, Sarov, Russia

Linear resonance electron accelerator LU-10-20 is under operation in RFNC-VNIIEF since 1994*. LU-10-20 is aimed at carrying out radiation processing of materials and researching radiation processes. The energy of accelerated electrons is up to 10 MeV, the average beam power - up to 12 kW. This accelerator has demonstrated that it is highly useful for performing radiation researches and tests. As of today work is underway on modernization of LU-10-20 including its accelerating structure and RF power supply. Accelerating structure is aimed at electron beam acceleration up to nominal energy and consists of complicated resonance TW RF structure, which uncluded iris-loaded waveguide, input and output matching devices. The paper presents the electrodynamic calculation results of modernized accelerating structure, input and output matching devices, and also beam dynamics calculation results.
*N.V.Zavyalov et al. Commercial linear accelerator of electrons LU-10-20. Materials of the XV All-Union Seminar on Linear Accelerators of Charged Particles, Nucl. Phys. Res.No2, 3(29, 30),1997, p.39-41.

DOI •

reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-WEPSC04

About •

Received ※ 28 September 2021 — Revised ※ 29 September 2021 — Accepted ※ 09 October 2021 — Issued ※ 18 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPSC57

System of on-Line Energy Control of Electron Beam for Accelerator

446

N.N. Kurapov, Ya.V. Bodryashkin, A.S. Cherkasov, I.V. Shorikov
RFNC-VNIIEF, Sarov, Nizhniy Novgorod region, Russia
A.V. Telnov
VNIIEF, Sarov, Russia

There arises a need for measuring the output electron energy in the on-line mode during set-up, adjustment or operation of an accelerator. For this purpose a system is developed, allowing an on-line control of an accelerated electron energy spectrum simultaneously with average current measurement. This system is meant for reconstruction of the energy spectrum of accelerated electrons in the energy range from 1 up to 10 MeV at the average beam current from 20 up to 150 µA. The system is based on the method of absorbing filters and consists of an assembly, absorbing an accelerated electron beam, and a measuring system. The absorption assembly represents a set of insulated from each other electro-conducting plates of dimension 100x100 mm and thickness from 0.15 up to 1 mm with an air gap between plates 2 mm. The operation involves development, manufacture and calculation of electron beam transmission through the absorption assembly, development and manufacture of hardware for automated measuring of absorbed charges in the assembly elements, development of a master computer program as well as a program of energy spectrum reconstruction, using measured and calculated data, testing of the energy on-line control system on the LU-10-20 linear resonance electron accelerator. Tests of the developed sample on the electron accelerator have proved the applicability of the system to control the electron beam energy in the real-time mode.

DOI •

reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-WEPSC57

About •

Received ※ 27 September 2021 — Revised ※ 30 September 2021 — Accepted ※ 09 October 2021 — Issued ※ 22 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)