RuPAC2021 - List of Authors (Makarov, A.)

Paper	Title	Page
TUPSB35	3D Simulation Study and Optimization of Magnetic System of DECRIS Ion Source with the Pumping Frequency 28 GHz	300
	V.M. Amoskov, E.I. Gapionok, V.P. Kukhtin, A.N. Labusov, E.A. Lamzin, A. Makarov, I.Yu. Rodin, A.V. Safonov, N. Shatil, D.B. Stepanov, E.R. Zapretilina NIIEFA, St. Petersburg, Russia S.L. Bogomolov, A.A. Efremov JINR, Dubna, Moscow Region, Russia S.E. Sytchevsky Saint Petersburg State University, Saint Petersburg, Russia
	A superconducting magnet system for a 28 GHz ECR ion source DECRIS-SC2 was studied in order to select its parameters and optimize performance. Parametric magnetic models were performed for two design configurations, conventional ("sextupole-in-solenoid") and reversed ("solenoid-in-sextupole"). In the "sextupole-in-solenoid" design the racetrack coils of the sextupole magnet used for radial plasma confinement are located inside the solenoids producing the axial field. In the "solenoid-in-sextupole" design the coils arrangement is reversed. For both configurations, electromagnetic effect the booster and the steel poles on the magnet performance was investigated from the point of view critical parameters of the system ¿ currents, fields, and forces. Results of the parametric computations were used to optimize the geometry and sizes of the magnet as well as the magnetic shield, the booster, and the poles. For better reliability and validation of the result, computations were performed with two magnetostatic codes, KOMPOT and KLONDIKE, utilizing the differential and integral formulations, respectively. A comparison of the obtained parameters was used to select the candidate magnet configuration for further design and manufacture.
DOI •	reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-TUPSB35
About •	Received ※ 28 September 2021 — Revised ※ 29 September 2021 — Accepted ※ 04 October 2021 — Issued ※ 18 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRA03	Simulation and Design of the Permanent Magnet Multipole for DC140	99
	V.P. Kukhtin, A.A. Firsov, M. Kaparkova, E.A. Lamzin, M.S. Larionov, A. Makarov, A. Nezhentzev, I.Yu. Rodin, N. Shatil NIIEFA, St. Petersburg, Russia N.S. Edamenko, D.A. Ovsyannikov St. Petersburg State University, St. Petersburg, Russia G.G. Gulbekyan, I.A. Ivanenko, I.V. Kalagin, N.Yu. Kazarinov, N.F. Osipov JINR, Dubna, Moscow Region, Russia S.E. Sytchevsky Saint Petersburg State University, Saint Petersburg, Russia
	Permanent magnet (PM) multipoles in some cases are good candidates in accelerator applications for beam transportation and focusing. The PM quadrupole will be utilized in the DC140 cyclotron which is under construction in JINR. A passive magnetic channel and a PM quad will be used for the compensation of horizontal defocusing in the high and low field regions, respectively. The quad is designed as a set of identical PMs rigidly fixed in a non-magnetic housing and capable to generate a a 8.1 T/m gradient field in the 64x25 mm aperture and 29.926 cm effective length. The error of linear approximation should be 1% or less. A special study was accomplished to define the PM specification reasoning from the demand for desired field strength, simple geometry, minimized nomenclature, and commercial availability. The quad design was selected with the use a 2D analytical model and then optimized in iterative 3D FE simulations with realistic PM shape and magnetic characteristics in mind. The resultant concept is the quad formed with 6 coaxial sections each 5cm in width. Every section has 26 identical PM bricks with the dimensions 11mmx11mmx50mm and different orientations. The PM bricks have remanent induction of 1.185 T and magnetic susceptibility of 0.1. Temperature characteristics and expected lifetime were also analysed. From the results obtained, candidate PM materials were proposed and mechanical and magnetic precision were recommended.
	Slides FRA03 [1.465 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-FRA03
About •	Received ※ 09 September 2021 — Accepted ※ 29 September 2021 — Issued ※ 12 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

3D Simulation Study and Optimization of Magnetic System of DECRIS Ion Source with the Pumping Frequency 28 GHz

300

V.M. Amoskov, E.I. Gapionok, V.P. Kukhtin, A.N. Labusov, E.A. Lamzin, A. Makarov, I.Yu. Rodin, A.V. Safonov, N. Shatil, D.B. Stepanov, E.R. Zapretilina
NIIEFA, St. Petersburg, Russia
S.L. Bogomolov, A.A. Efremov
JINR, Dubna, Moscow Region, Russia
S.E. Sytchevsky
Saint Petersburg State University, Saint Petersburg, Russia

A superconducting magnet system for a 28 GHz ECR ion source DECRIS-SC2 was studied in order to select its parameters and optimize performance. Parametric magnetic models were performed for two design configurations, conventional ("sextupole-in-solenoid") and reversed ("solenoid-in-sextupole"). In the "sextupole-in-solenoid" design the racetrack coils of the sextupole magnet used for radial plasma confinement are located inside the solenoids producing the axial field. In the "solenoid-in-sextupole" design the coils arrangement is reversed. For both configurations, electromagnetic effect the booster and the steel poles on the magnet performance was investigated from the point of view critical parameters of the system ¿ currents, fields, and forces. Results of the parametric computations were used to optimize the geometry and sizes of the magnet as well as the magnetic shield, the booster, and the poles. For better reliability and validation of the result, computations were performed with two magnetostatic codes, KOMPOT and KLONDIKE, utilizing the differential and integral formulations, respectively. A comparison of the obtained parameters was used to select the candidate magnet configuration for further design and manufacture.

DOI •

reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-TUPSB35

About •

Received ※ 28 September 2021 — Revised ※ 29 September 2021 — Accepted ※ 04 October 2021 — Issued ※ 18 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

FRA03

Simulation and Design of the Permanent Magnet Multipole for DC140

99

V.P. Kukhtin, A.A. Firsov, M. Kaparkova, E.A. Lamzin, M.S. Larionov, A. Makarov, A. Nezhentzev, I.Yu. Rodin, N. Shatil
NIIEFA, St. Petersburg, Russia
N.S. Edamenko, D.A. Ovsyannikov
St. Petersburg State University, St. Petersburg, Russia
G.G. Gulbekyan, I.A. Ivanenko, I.V. Kalagin, N.Yu. Kazarinov, N.F. Osipov
JINR, Dubna, Moscow Region, Russia
S.E. Sytchevsky
Saint Petersburg State University, Saint Petersburg, Russia

Permanent magnet (PM) multipoles in some cases are good candidates in accelerator applications for beam transportation and focusing. The PM quadrupole will be utilized in the DC140 cyclotron which is under construction in JINR. A passive magnetic channel and a PM quad will be used for the compensation of horizontal defocusing in the high and low field regions, respectively. The quad is designed as a set of identical PMs rigidly fixed in a non-magnetic housing and capable to generate a a 8.1 T/m gradient field in the 64x25 mm aperture and 29.926 cm effective length. The error of linear approximation should be 1% or less. A special study was accomplished to define the PM specification reasoning from the demand for desired field strength, simple geometry, minimized nomenclature, and commercial availability. The quad design was selected with the use a 2D analytical model and then optimized in iterative 3D FE simulations with realistic PM shape and magnetic characteristics in mind. The resultant concept is the quad formed with 6 coaxial sections each 5cm in width. Every section has 26 identical PM bricks with the dimensions 11mmx11mmx50mm and different orientations. The PM bricks have remanent induction of 1.185 T and magnetic susceptibility of 0.1. Temperature characteristics and expected lifetime were also analysed. From the results obtained, candidate PM materials were proposed and mechanical and magnetic precision were recommended.

Slides FRA03 [1.465 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-RuPAC2021-FRA03

About •

Received ※ 09 September 2021 — Accepted ※ 29 September 2021 — Issued ※ 12 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)