BNL, Upton, Long Island, New York
In this paper we describe unique features of magnets for R&D ERL, which is under construction in Collider-Accelerator Department, BNL. The R&D ERL serves as a test-bed future BNL ERLs, such as electron-cooler-ERL for RHIC and 20 GeV ERL for future electron-hadron, eRHIC. We present selected designs of various dipole and quadrupole magnets, which are used in Z-bend merging systems and the returning loop, 3-D simulations of the fields in these magnets, particle tracking and analysis of magnet's influence on the beam parameters. We discuss an uncommon method of setting requirements on the quality of magnetic field and transferring them into measurable parameters as well as into manufacturing tolerances. We compare selected simulation with results magnetic measurements.
BNL, Upton, Long Island, New York
BNL, Upton, Long Island, New York
AES, Princeton, New Jersey
CLASSE, Ithaca
Stony Brook University, StonyBrook
Jefferson Lab, Newport News, Virginia
In this paper we present status and plans for the 20-MeV R&D energy recovery linac, which is under construction at Collider Accelerator Department at BNL. The facility is based on high current (up to 0.5 A of average current) super-conducting 2.5 MeV RF gun, single-mode super-conducting 5-cell RF linac and about 20-m long return loop with very flexible lattice. The R&D ERL, which is planned for commissioning in 2008, aims to address many outstanding questions relevant for high current, high brightness energy-recovery linacs.
BNL, Upton, Long Island, New York
Tech-X, Boulder, Colorado
ORNL, Oak Ridge, Tennessee
AES, Princeton, New Jersey
Fermilab, Batavia, Illinois
Jefferson Lab, Newport News, Virginia
BINP SB RAS, Novosibirsk
JINR, Dubna, Moscow Region
The physics interest in a luminosity upgrade of RHIC requires the development of a cooling-frontier facility. Detailed cooling calculations have been made to determine the efficacy of electron cooling of the stored RHIC beams. This has been followed by beam dynamics simulations to establish the feasibility of creating the necessary electron beam. Electron cooling of RHIC at collisions requires electron beam energy up to about 54 MeV at an average current of between 50 to 100 mA and a particularly bright electron beam. The accelerator chosen to generate this electron beam is a superconducting Energy Recovery Linac (ERL) with a superconducting RF gun with a laser-photocathode. An intensive experimental R&D program engages the various elements of the accelerator: Photocathodes of novel design, superconducting RF electron gun of a particularly high current and low emittance, a very high-current ERL cavity and a demonstration ERL using these components.
BNL, Upton, Long Island, New York
Tech-X, Boulder, Colorado
JINR, Dubna, Moscow Region
The traditional electron cooling system used in low-energy coolers employs an electron beam immersed in a longitudinal magnetic field. In the first relativistic cooler, which was recently commissioned at Fermilab, the friction force is dominated by the non-magnetized collisions between electrons and antiprotons. The design of the higher-energy cooler for Relativistic Heavy Ion Collider (RHIC) recently adopted a non-magnetized approach which requires a low temperature electron beam. However, to avoid significant loss of heavy ions due to recombination with electrons in the cooling section, the temperature of the electron beam should be very high. These two contradictory requirements are satisfied in the design of the RHIC cooler with the help of the undulator fields. The model of the friction force in the presence of an undulator field was benchmarked vs direct numerical simulations with an excellent agreement. Simulations of ion beam dynamics in the presence of such a cooler and helical undulator is discussed in detail, including recombination suppression and resulting luminosities.
BNL, Upton, Long Island, New York
JINR, Dubna, Moscow Region
The low-energy electron cooling system is based on an electron beam immersed in a longitudinal magnetic field of a solenoid. The coupling of the horizontal and vertical motion allows representation of the friction force as a sum of the transverse and longitudinal components. The analytic treatment proceeds by allowing several approximations, for example, uniform transverse density distribution of electron beam and Maxwellian distribution in the velocity space. The high-energy electron cooling system for RHIC is unique compared to standard coolers. It requires bunched electron beam. Electron bunches are produced by an Energy Recovery Linac (ERL), and cooling is planned without a longitudinal magnetic field. To address the unique features of the RHIC cooler, a generalized 3-D treatment of the cooling force was introduced in the BETACOOL code which allows to calculate the friction force from an arbitrary six-dimensional distribution of the electrons. Results based on this treatment are compared to typical approximations. Simulations for the RHIC cooler based on a realistic electron distribution from the ERL are presented.
BNL, Upton, Long Island, New York
Non-magnetized electron cooling of RHIC requires an electron beam energy of 54.3 MeV, electron charge per bunch of 5 nC, normalized rms beam emittance of 4 mm-mrad, and rms energy spread of 3·10-4 *. In this paper we describe a lattice of a two-pass SCRF energy recovery linac (ERL) and results of a PARMELA simulation that provides electron beam parameters satisfying RHIC electron cooling requirements.
* A. Fedotov, Electron Cooling Studies for RHIC II http://www.bnl.gov/cad/ecooling/docs/PDF/Electron_Cooling.pdf
BNL, Upton, Long Island, New York
A super-conducting RF R&D Energy recovery linac (ERL) is under construction at Brookhaven National Laboratory (BNL). This ERL will be used as a test facility to study issues relevant to high-current, high-brightness beams. One of the goals is to demonstrate an electron beam with high charge per bunch (~ 5 nC) and extremely low normalized emittance (~ 5 mm-mrad) at an energy of 20 MeV. In contrast with operational high-brightness linear electron accelerators, all presently operating ERLs have an order of magnitude larger emittances for the same charge per bunch. One reason for this emittance growth is that the merger system mixes transverse and longitudinal degrees of freedom, and consequently violates emittance compensation conditions. A merger system based on zigzag scheme* resolves this problem. In this paper we discuss performance of the present design of the BNL R&D ERL injector with a zigzag merger.
* V. N. Litvinenko, R. Hajima, and D. Kayran, Nucl. Instr. and Meth. A 557 (2006) 165.
BNL, Upton, Long Island, New York
Electron cooling at RHIC-II upgrade imposes strict requirements on the quality of the electron beam at the cooling section. Beam current dependent effects such as the space charge, wake fields, CSR in bending magnets, trapped ions, etc., will tend to spoil the beam quality and decrease the cooling efficiency. In this paper, we estimate the defocusing effect of the space charge at the cooling section and describe our plan to compensate the defocusing space charge force by focusing solenoids. We also estimate the energy spread and emittance growth cased by wake fields. Finally, we discuss ion trapping in the electron cooler and consider different techniques to minimize the effect of ion trapping.
BNL, Upton, Long Island, New York
The ERL Prototype project is currently under development at the Brookhaven National Laboratory. The ERL is expected to demonstrate energy recovery of high-intensity beams with a current of up to a few hundred milliamps, while preserving the emittance of bunches with a charge of a few nanocoulombs produced by a high-current SRF gun. To successfully accomplish this task the machine will include beam diagnostics that will be used for accurate characterization of the three dimensional beam phase space at the injection and recirculation energies, transverse and longitudinal beam matching, orbit alignment, beam current measurement, and machine protection. This paper outlines requirements on the ERL diagnostics and describes its setup and modes of operation.