Paper | Title | Page |
---|---|---|
THPPP010 | Mechanical Analysis and Tests of Austenitic Stainless Steel Bolts for Beamline Flange Connection | 290 |
|
||
Cryogenic tests of 1.3GHz superconducting accelerator cryomodule for the Shanghai Hard X-ray Free Electron Laser Installation Project(SHINE) are in progress. For better performance, a study of mechanical analysis and tests of austenitic stainless steel bolts for beamline flange connection has been done in preliminary work. In order to satisfy the residual magnetism and strength, high-strength austenitic stainless steel bolts are selected. For higher sealing performance, the torque coefficient is determined by compression test, the lower limit of yield of the bolts is obtained by tensile test, then the maximum torque applied to the bolts under real working conditions can be obtained according to the relationship between preload and torque. A finite element model is established to get the deformation curve of the gasket, and the measured results of gasket thickness are compared to ensure the reliability of the simulation. The deformation curve of the gasket is used to calculate the change of compression force under the temperature cycling load(cool down and warm-up). Finally, the results of residual magnetism show that the bolts have a negligible effect on magnetic field. | ||
DOI • | reference for this paper ※ doi:10.18429/JACoW-MEDSI2023-THPPP010 | |
About • | Received ※ 25 October 2023 — Revised ※ 06 November 2023 — Accepted ※ 09 November 2023 — Issued ※ 18 November 2023 | |
Cite • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
THPPP035 | Mechanical System of the U26 Undulator Prototype for SHINE | 325 |
|
||
The Shanghai High repetition rate XFEL and Extreme light facility (SHINE) is under construction and aims at generating X-rays between 0.4 and 25 keV with three FEL beamlines at repetition rates of up to 1 MHz[1-3]. The three undulator lines of the SHINE are referred to as the FEL-I, FEL-II, and FEL-III. Shanghai Synchrotron Radiation Facility(SSRF) will manufacture a total of 42 undulators (U26) with a period length of 26mm for FEL-I and 22 undulators (U55) with a period length of 55mm for FEL-II. Both the U26 and U55 are 4m long and use a common mechanical system. By using the specially designed double lever compensation springs can eliminate different magnetic force on the drive units. A U26 prototype has been developed and tested at SSRF. This paper describes the mechanical system design¿simulation and testing results of the U26 prototype, as well as its compatibility with U55. | ||
DOI • | reference for this paper ※ doi:10.18429/JACoW-MEDSI2023-THPPP035 | |
About • | Received ※ 25 October 2023 — Revised ※ 07 November 2023 — Accepted ※ 08 November 2023 — Issued ※ 11 December 2023 | |
Cite • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
THPPP036 | Prototype of High Stability Mechanical Support for SHINE Project | 328 |
|
||
Funding: CAS Project for Young Scientists in Basic Research (YSBR-042), National Natural Science Foundation of China (12125508, 11935020)¿Program of Shanghai Academic/Technology Research Leader (21XD1404100). Quadrupole stability of undulator segment is key to the beam performance in SHINE project. Vibration stability requirement of quadrupole is not larger than 200nm displacement RMS between 1 and 100Hz, but the field test of SHINE tunnel shows that the underground vibration during the day time is greater than 200nm. In this paper, a mechanical support including marble base and active vibration reduction platform is sophisticated designed. With this support, vibration stability of the key quadrupole is expected to be improved and the performances of the quadrupole meet the demands. |
||
DOI • | reference for this paper ※ doi:10.18429/JACoW-MEDSI2023-THPPP036 | |
About • | Received ※ 25 October 2023 — Revised ※ 07 November 2023 — Accepted ※ 08 November 2023 — Issued ※ 12 January 2024 | |
Cite • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |