FRXXPLS —  Contributed Oral: Beam Instrumentation, Controls, Feedback and Operation   (24-May-19   09:00—10:00)
Chair: B. Marchetti, DESY, Hamburg, Germany
Paper Title Page
FRXXPLS1 Tests of a 3D Printed BPM with a Stretched Wire and with a Particle Beam 4368
 
  • N. Delerue, D. Auguste, J. Bonis, F. Gauthier, S. Jenzer, A.M. Moutardier
    LAL, Orsay, France
  
  Funding: CNRS/IN2P3
We have successfully printed a beam position monitor using 3D printing. After ultra-high vacuum testing and initial measurements with a network analyser we now reports on tests of this BPM using the stretched wire method. The BPM has been installed on a test stand with a wire going through it and electrical pulses have been sent. The signal measured on the pick-ups was compared to that of two conventional BPMs and shows no anomaly specific to the 3D printed BPMs. Following the success of these tests we have also installed this BPM in a beam line at the PhotoInjector at LAL (PHIL). We show that it can give position measurements with an accuracy comparable to that of other BPMs. 		 
slides icon Slides FRXXPLS1 [29.118 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-FRXXPLS1  
About • paper received ※ 19 May 2019       paper accepted ※ 22 May 2019       issue date ※ 21 June 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
FRXXPLS2 Extinction Measurement of J-PARC MR with 8 GeV Proton Beam for the New Muon-to-Electron Conversion Search Experiment - COMET 4372
 
  • H. Nishiguchi, Y. Fukao, Y. Hashimoto, Y. Igarashi, S. Mihara, M. Moritsu, R. Muto, M. Tomizawa, K. Ueno
    KEK, Tsukuba, Japan
  • Y. Fujii
    Monash University, Faculty of Science, Clayton, Victoria, Australia
  • P. Sarin
    Indian Institute of Technology Bombay, Mumbai, India
  • F. Tamura
    JAEA/J-PARC, Tokai-mura, Japan
  
  Funding: This work is partially supported by JSPS (Japan Society for the Promotion of Science) : KAKENHI 15K13492 and 16H00876
At J-PARC, extraction tests of a 8GeV pulsed proton beam from Main Ring (MR) have been successfully completed by a team drawn from the Accelerator Laboratory Group and the COherent Muon to Electron Transition (COMET) Experimental Group. The COMET Experiment aims to find new physics beyond the Standard Model by searching for the coherent neutrinoless conversion of a muon to an electron in muonic atoms, so-called mu-e conversion. This requires an extremely clean pulsed beam, and development of this beam plays a key role in the pursuit of the highest level of sensitivity. This successful extraction test is the clearing of a major milestone for the forthcoming experiment. The goal of the extraction tests was to confirm the beam quality under the customized MR operation mode. The J-PARC MR usually accelerates the proton beam (at one bunch per 600ns) up to 30GeV. But in the test, the MR instead accelerates the proton beam (at one bunch per 1.2us) up to 8GeV. The number of protons leaking between proton bunches, so-called EXTINCTION, must be less than one for every 1010 protons in the bunch. Extraction tests in the customized mode were conducted in January and February 2018 and resulted in many successes. In this test, leakage protons between bunches was successfully reduced below the objective of 10−10 of the number of protons in a bunch. This is a great success to guarantee the quality of proton beam required by COMET experiment. In addition, the time development of proton leakage was also precisely studied with several RF settings which enables us to further improve the extinction. In this paper, the result of extinction measurement and future prospect of beam extinction improvement is presented in addition to the detailed description of customized MR operation. 		 
slides icon Slides FRXXPLS2 [13.427 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-FRXXPLS2  
About • paper received ※ 15 May 2019       paper accepted ※ 21 May 2019       issue date ※ 21 June 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
FRXXPLS3 Application of a Phase Space Beam Position and Size Monitor for Synchrotron Radiation 4376
SUSPFO003   use link to see paper's listing under its alternate paper code  
 
  • N. Samadi
    University of Saskatchewan, Saskatoon, Canada
  • L.D. Chapman, L.O. Dallin
    CLS, Saskatoon, Saskatchewan, Canada
  • X. Shi
    ANL, Argonne, Illinois, USA
  
  We will report on a system (ps-BPM) that can measure the electron source vertical position and angular motion along with the vertical source size and angular size at a single location in a synchrotron bend magnet beamline*. This system uses a combination of a monochromator and a filter with a K-edge to which the monochromator was tuned in energy. The vertical distribution of the beam with and without the filter was simultaneously visualized with an imaging detector. The small range of angles from the source onto the monochromator crystals creates an energy range that allows part of the beam to be below the K-edge and the other part above. Measurement of the beam vertical location without the absorber and edge vertical location with the absorber allowes measurement of the source position and angle. The beam width and edge width give information about the vertical electron source size and angular distribution. The ps-BPM measurements have been made where the electron beam size and angular distribution was adjusted using skew quads. The ps-BPM measurements correlate well with modeling of the ps-BPM system as well as conventional beam size measurements using a pinhole.
* A phase-space beam position monitor for synchrotron radiation. J Synchrotron Radiat, 2015. 22(4): p. 946-55. 		 
slides icon Slides FRXXPLS3 [4.593 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-FRXXPLS3  
About • paper received ※ 15 May 2019       paper accepted ※ 21 May 2019       issue date ※ 21 June 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)