IPAC2019 - List of Authors (Auchettl, R.)

Paper	Title	Page
TUZZPLS2	Beam Dynamics, Injection and Impedance Studies for the Proposed Single Pulsed Nonlinear Injection Kicker at the Australian Synchrotron	1219
	R. Auchettl, R.T. Dowd, Y.E. Tan AS - ANSTO, Clayton, Australia
	The Australian Synchrotron are currently investigating the use of a single pulsed nonlinear injection kicker (NLK) to free floor space within the ring for future beamline development. The NLK has a zero and flat magnetic field at the stored beam to leave the stored beam undisturbed but has a maximum field off-axis where the injected beam is located. After the kick, the injected beam is stored. While NLKs have been prototyped at many facilities around the world, injection efficiency and heat loading have been the main impediment to deployment of the NLK. The wakefields that pass through the ceramic chamber aperture can cause severe heat loading and impedance. Despite achieving impressive injection efficiencies, a previous prototype at BESSY II * showed that strong interactions of the stored beam resulted in high heat load causing the thin 5µm Titanium coated ceramic chamber to reach temperatures > 500 °C and fail. To avoid beam induced heat loads, this paper presents studies of the wake impedance and thermal behaviour for our proposed NLK design. Injection simulations and future considerations for installation and operation at the Australian Synchrotron will be discussed. * T. Atkinson et al., "Development of a non-linear kicker system to facilitate a new injection scheme for the Bessy II storage ring", in Proc. IPAC’11, 2011, THPO024, pp. 3394-3396.
	Slides TUZZPLS2 [1.588 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-TUZZPLS2
About •	paper received ※ 15 May 2019 paper accepted ※ 22 May 2019 issue date ※ 21 June 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMP001	Proposed Nonlinear Injection Kicker for the Australian Synchrotron	2300
	R. Auchettl, Y.E. Tan AS - ANSTO, Clayton, Australia
	Future beamline development at the Australian Synchrotron requires free floor space within the straights for a short undulator and relocation of diagnostics. Our current injection method uses a four-dipole kicker configuration that perturbs the stored beam during injection while also taking up approximately 4 meters of valuable space. To free this valuable space and provide transparent injections to the beamlines, a single pulsed nonlinear magnetic field kicker (NLK) will be deployed. The NLK has a flat and zero field at the stored beam but maximum field where the injected beam is located off-axis. NLKs deflect only the injected beam, leaving the stored beam undisturbed. NLKs have been extensively prototyped by many facilities around the world already and can produce injection efficiencies of 99 % (see e.g. ). This paper presents the preliminary magnet design for installation of a NLK at the Australian Synchrotron. We discuss the beam dynamics and thermal transfer constraints on kicker placement, field-flatness and the magnet and ceramic chamber design for adaptation to our 3 GeV beam. Installation plans and other constraints for future deployment are also outlined. T. Pulampong and R. Bartolini, "A Non-linear Injection Kicker for Diamond Light Source", in: Proc. IPAC’13, pp. 2268-2270.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-WEPMP001
About •	paper received ※ 15 May 2019 paper accepted ※ 24 May 2019 issue date ※ 21 June 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPRB001	Applications of Online Optimization Algorithms for Injection at the Australian Synchrotron	3795
	R. Auchettl, R.T. Dowd AS - ANSTO, Clayton, Australia
	At the Australian Synchrotron, accelerator tuning predominantly occurs via manual optimization or traditional optimization techniques such as the Linear Optics from Closed Orbits (LOCO) algorithm. While we have had distinct success with the implementation of LOCO* and manual tuning, these strategies are not without their downsides. Some situations (such as the optimization of synchrotron beam dynamics) produce a design space too large and multifaceted for manual tuning while implementing LOCO can be computationally expensive. Also, without sufficient diagnostic systems, both LOCO and manual tuning do not necessarily guarantee that the optimal solution will be found. Motivated by the successful implementation of online optimization algorithms at SPEAR3*, this paper outlines the application of online optimization algorithms to improve the performance of the Australian Synchrotron injection system. We apply the efficient Robust Conjugate Direction Search (RCDS) Algorithm to reduce beam loss along the Booster-to-Storage ring (BTS) Transfer line and Storage Ring and compare against the LOCO method. R. Dowd et al. (2011), Phys. Rev. ST: AB, 14, 012804. ** X. Huang et al. (2013), Nucl. Instr. Meth. A., vol. 726, pp. 77-83.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-THPRB001
About •	paper received ※ 08 April 2019 paper accepted ※ 21 May 2019 issue date ※ 21 June 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Beam Dynamics, Injection and Impedance Studies for the Proposed Single Pulsed Nonlinear Injection Kicker at the Australian Synchrotron

1219

R. Auchettl, R.T. Dowd, Y.E. Tan
AS - ANSTO, Clayton, Australia

The Australian Synchrotron are currently investigating the use of a single pulsed nonlinear injection kicker (NLK) to free floor space within the ring for future beamline development. The NLK has a zero and flat magnetic field at the stored beam to leave the stored beam undisturbed but has a maximum field off-axis where the injected beam is located. After the kick, the injected beam is stored. While NLKs have been prototyped at many facilities around the world, injection efficiency and heat loading have been the main impediment to deployment of the NLK. The wakefields that pass through the ceramic chamber aperture can cause severe heat loading and impedance. Despite achieving impressive injection efficiencies, a previous prototype at BESSY II * showed that strong interactions of the stored beam resulted in high heat load causing the thin 5µm Titanium coated ceramic chamber to reach temperatures > 500 °C and fail. To avoid beam induced heat loads, this paper presents studies of the wake impedance and thermal behaviour for our proposed NLK design. Injection simulations and future considerations for installation and operation at the Australian Synchrotron will be discussed.
* T. Atkinson et al., "Development of a non-linear kicker system to facilitate a new injection scheme for the Bessy II storage ring", in Proc. IPAC’11, 2011, THPO024, pp. 3394-3396.

Slides TUZZPLS2 [1.588 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-TUZZPLS2

About •

paper received ※ 15 May 2019 paper accepted ※ 22 May 2019 issue date ※ 21 June 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMP001

Proposed Nonlinear Injection Kicker for the Australian Synchrotron

2300

R. Auchettl, Y.E. Tan
AS - ANSTO, Clayton, Australia

Future beamline development at the Australian Synchrotron requires free floor space within the straights for a short undulator and relocation of diagnostics. Our current injection method uses a four-dipole kicker configuration that perturbs the stored beam during injection while also taking up approximately 4 meters of valuable space. To free this valuable space and provide transparent injections to the beamlines, a single pulsed nonlinear magnetic field kicker (NLK) will be deployed. The NLK has a flat and zero field at the stored beam but maximum field where the injected beam is located off-axis. NLKs deflect only the injected beam, leaving the stored beam undisturbed. NLKs have been extensively prototyped by many facilities around the world already and can produce injection efficiencies of 99 % (see e.g. *). This paper presents the preliminary magnet design for installation of a NLK at the Australian Synchrotron. We discuss the beam dynamics and thermal transfer constraints on kicker placement, field-flatness and the magnet and ceramic chamber design for adaptation to our 3 GeV beam. Installation plans and other constraints for future deployment are also outlined.
* T. Pulampong and R. Bartolini, "A Non-linear Injection Kicker for Diamond Light Source", in: Proc. IPAC’13, pp. 2268-2270.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-WEPMP001

About •

paper received ※ 15 May 2019 paper accepted ※ 24 May 2019 issue date ※ 21 June 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPRB001

Applications of Online Optimization Algorithms for Injection at the Australian Synchrotron

3795

R. Auchettl, R.T. Dowd
AS - ANSTO, Clayton, Australia

At the Australian Synchrotron, accelerator tuning predominantly occurs via manual optimization or traditional optimization techniques such as the Linear Optics from Closed Orbits (LOCO) algorithm. While we have had distinct success with the implementation of LOCO* and manual tuning, these strategies are not without their downsides. Some situations (such as the optimization of synchrotron beam dynamics) produce a design space too large and multifaceted for manual tuning while implementing LOCO can be computationally expensive. Also, without sufficient diagnostic systems, both LOCO and manual tuning do not necessarily guarantee that the optimal solution will be found. Motivated by the successful implementation of online optimization algorithms at SPEAR3**, this paper outlines the application of online optimization algorithms to improve the performance of the Australian Synchrotron injection system. We apply the efficient Robust Conjugate Direction Search (RCDS) Algorithm to reduce beam loss along the Booster-to-Storage ring (BTS) Transfer line and Storage Ring and compare against the LOCO method.
* R. Dowd et al. (2011), Phys. Rev. ST: AB, 14, 012804.
** X. Huang et al. (2013), Nucl. Instr. Meth. A., vol. 726, pp. 77-83.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-THPRB001

About •

paper received ※ 08 April 2019 paper accepted ※ 21 May 2019 issue date ※ 21 June 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)