IPAC2017 - List of Authors (Kamiya, J.)

Paper	Title	Page
MOPIK035	New Injection Scheme of J-PARC Rapid Cycling Synchrotron	579
	K. Yamamoto, H. Harada, H. Hotchi, J. Kamiya, P.K. Saha, T. Takayanagi, M. Yoshimoto JAEA/J-PARC, Tokai-mura, Japan N. Miki, O. Takeda Nippon Advanced Technology Co., Ltd., Tokai, Japan
	The 3-GeV Rapid Cycling Synchrotron (RCS) of Japan Proton Accelerator Research Complex (J-PARC) aims to deliver 1-MW proton beam to the neutron target and Main Ring synchrotron (MR). Present beam power of RCS is up to 500-kW and the higher radiation doses were concentrated in the injection area. These activations were caused by the interaction between the foil and the beam. To reduce the worker dose near the injection point, we have studied new design of the injection scheme to secure enough space for radiation shielding and bellows. In the new system, two of four injection pulse bump magnets are replaced and we are able to ensure the additional 500 mm space at the injection foil .
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2017-MOPIK035
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPVA062	Improvements of Vacuum System in J-PARC 3 GeV Synchrotron	3408
	J. Kamiya, Y. Hikichi, M. Kinsho, Y. Namekawa, K. Takeishi, T. Yanagibashi JAEA/J-PARC, Tokai-mura, Japan A. Sato Nippon Advanced Technology Co., Ltd., Tokai, Japan
	The RCS vacuum system has been upgraded since the completion of its construction towards the objectives of both better vacuum quality and higher reliability of the components. For the better vacuum quality, (1) pressure of the injection beam line was improved to prevent the H⁻ beam from converting to H0; (2) leakage in the beam injection area due to the thermal expansion was eliminated by applying the adequate torque amount for the clamps; (3) new in-situ degassing method of the kicker magnet was developed. For the reliability increase of the components, (1) A considerable number of fluoroelastmer seal was exchanged to metal seal with the low spring constant bellows and the light clamps; (2) TMP controller for the long cable was developed to prevent the controller failure by the severe electrical noise; (3) A number of TMP were installed instead of ion pumps in the RF cavity section as an insurance for the case of pump trouble.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2017-WEPVA062
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPVA063	Development of a New Pulsed Power Supply with the SiC-MOSFET	3412
	T. Takayanagi, K. Horino, J. Kamiya, M. Kinsho, T. Ueno, K. Yamamoto JAEA/J-PARC, Tokai-mura, Japan Y. Mushibe, A. Tokuchi Pulsed Power Japan Laboratory Ltd., Kusatsu-shi Shiga, Japan
	A new power supply has been developed using linear transformer driver (LTD) technology that adopts SiC-MOSFETs and capacitors without a thyratron switch or a pulse forming network (PFN) device. A new power supply was also designed by connecting the SiC-MOSFETs and the LTD modules in parallel-series. The output voltage and current were 40 kV and 4 kA, respectively with a pulse width of 1500 nsec at a repetition rate of 25 Hz. Furthermore, by adjusting the correction module, to an output voltage per stage of 1/1000, a resolution of the voltage correction of ±0.1 % could be achieved. It was possible to output the current with arbitrary timing by using a trigger input for each LTD module. As a result, fine adjustment of the output voltage waveform was possible within the order of nanoseconds. This new power supply with high voltage output, cur-rent output, and very fast pulse operation is one of the most important key technologies for a kicker system using SiC-MOSFETs. The design and preliminary test results of this prototype power supply are presented here.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2017-WEPVA063
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

New Injection Scheme of J-PARC Rapid Cycling Synchrotron

579

K. Yamamoto, H. Harada, H. Hotchi, J. Kamiya, P.K. Saha, T. Takayanagi, M. Yoshimoto
JAEA/J-PARC, Tokai-mura, Japan
N. Miki, O. Takeda
Nippon Advanced Technology Co., Ltd., Tokai, Japan

The 3-GeV Rapid Cycling Synchrotron (RCS) of Japan Proton Accelerator Research Complex (J-PARC) aims to deliver 1-MW proton beam to the neutron target and Main Ring synchrotron (MR). Present beam power of RCS is up to 500-kW and the higher radiation doses were concentrated in the injection area. These activations were caused by the interaction between the foil and the beam. To reduce the worker dose near the injection point, we have studied new design of the injection scheme to secure enough space for radiation shielding and bellows. In the new system, two of four injection pulse bump magnets are replaced and we are able to ensure the additional 500 mm space at the injection foil .

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2017-MOPIK035

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPVA062

Improvements of Vacuum System in J-PARC 3 GeV Synchrotron

3408

J. Kamiya, Y. Hikichi, M. Kinsho, Y. Namekawa, K. Takeishi, T. Yanagibashi
JAEA/J-PARC, Tokai-mura, Japan
A. Sato
Nippon Advanced Technology Co., Ltd., Tokai, Japan

The RCS vacuum system has been upgraded since the completion of its construction towards the objectives of both better vacuum quality and higher reliability of the components. For the better vacuum quality, (1) pressure of the injection beam line was improved to prevent the H⁻ beam from converting to H0; (2) leakage in the beam injection area due to the thermal expansion was eliminated by applying the adequate torque amount for the clamps; (3) new in-situ degassing method of the kicker magnet was developed. For the reliability increase of the components, (1) A considerable number of fluoroelastmer seal was exchanged to metal seal with the low spring constant bellows and the light clamps; (2) TMP controller for the long cable was developed to prevent the controller failure by the severe electrical noise; (3) A number of TMP were installed instead of ion pumps in the RF cavity section as an insurance for the case of pump trouble.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2017-WEPVA062

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPVA063

Development of a New Pulsed Power Supply with the SiC-MOSFET

3412

T. Takayanagi, K. Horino, J. Kamiya, M. Kinsho, T. Ueno, K. Yamamoto
JAEA/J-PARC, Tokai-mura, Japan
Y. Mushibe, A. Tokuchi
Pulsed Power Japan Laboratory Ltd., Kusatsu-shi Shiga, Japan

A new power supply has been developed using linear transformer driver (LTD) technology that adopts SiC-MOSFETs and capacitors without a thyratron switch or a pulse forming network (PFN) device. A new power supply was also designed by connecting the SiC-MOSFETs and the LTD modules in parallel-series. The output voltage and current were 40 kV and 4 kA, respectively with a pulse width of 1500 nsec at a repetition rate of 25 Hz. Furthermore, by adjusting the correction module, to an output voltage per stage of 1/1000, a resolution of the voltage correction of ±0.1 % could be achieved. It was possible to output the current with arbitrary timing by using a trigger input for each LTD module. As a result, fine adjustment of the output voltage waveform was possible within the order of nanoseconds. This new power supply with high voltage output, cur-rent output, and very fast pulse operation is one of the most important key technologies for a kicker system using SiC-MOSFETs. The design and preliminary test results of this prototype power supply are presented here.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2017-WEPVA063

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)