Paper |
Title |
Page |
TUPIK101 |
Development and Construction of Safety and Control Systems for the TPS Front End Interlock |
1947 |
|
- J. -Y. Chuang, C.K. Chan, Y.M. Hsiao, C.K. Kuan, Y.Z. Lin, I.C. Sheng, Y.C. Yang
NSRRC, Hsinchu, Taiwan
- C.S. Lin
NPUST, Pingtung, Taiwan
|
|
|
The Taiwan photon source (TPS) at NSRRC (National Taiwan Photon Source) is a 3rd generation, 3 GeV storage ring with designed current of 500 mA. In phase-I, six insertion device beamlines have been available to users after the safety interlock systems were commissioned and reviewed. National Instrument (NI) compact RIO 9030 is used for the front end interlock control system, and both scan and FPGA modes are activated in a hybrid mode to enhance the safety reliability. The personnel and machine protection system as well as EPICS communications of the TPS control system are presented in this paper as well.
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-IPAC2017-TUPIK101
|
|
Export • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
WEPVA123 |
Beam Cleaning of the Vacuum System of the TPS Storage Ring without Baking in Situ |
3561 |
|
- C.K. Chan, C.-C. Chang, B.Y. Chen, C.M. Cheng, Y.T. Cheng, J. -Y. Chuang, Y.M. Hsiao, Y.T. Huang, I.C. Sheng, C. Shueh, L.H. Wu, Y.C. Yang
NSRRC, Hsinchu, Taiwan
|
|
|
A maintenance procedure without baking in situ has been successfully developed and applied to maintain and upgrade the TPS storage ring vacuum system to shorten the machine downtime. The data of photon-stimulated desorption(PSD) reveal that no obvious discrepancy between the in-situ baked and the non-in-situ baked vacuum systems. A beam conditioning dose of extent only 11.8 A·h is required to recover rapidly the dynamic pressure of an unbaked vacuum system to its pre-intervention value according to the TPS maintenance experience.
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-IPAC2017-WEPVA123
|
|
Export • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
THPVA068 |
General Design of ID Front Ends in the TPS |
4601 |
|
- C.K. Kuan, C.K. Chan, Y.T. Cheng, J. -Y. Chuang, Y.M. Hsiao, I.C. Sheng, C. Shueh, H.Y. Yan
NSRRC, Hsinchu, Taiwan
|
|
|
The Taiwan Photon Source is a 3 GeV, 3rd generation synchrotron radiation source at the NSRRC. Phase-I commissioning includes seven Insertion Device (ID) Front Ends which are built to transmit intense synchro-tron radiation generated by In-vacuum Undulators and Elliptically Polarizing Undulators in the storage ring to the Photon Beamline. The total power and power distri-bution on Front End components is calculated and ana-lysed and Finite Element Analysis is used to verify the thermal performance under high heat loads while Monte-Carlo methods are utilized to simulate the vacuum pres-sure distribution. All apertures of the components are the same to simplify and standardize the design of the Front Ends. This paper describes main design considerations, especially the high heat load and vacuum pressure distri-bution.
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-IPAC2017-THPVA068
|
|
Export • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|