| Paper | Title | Page |
|---|---|---|
| TUPMW014 | Improved Aperture Measurements at the LHC and Results from their Application in 2015 | 1446 |
|
||
| A good knowledge of the available aperture in the LHC is essential for a safe operation due to the risk of magnet quenches or even damage in case of uncontrolled beam losses. Experimental validations of the available aperture are therefore crucial and were in the past carried out by either a collimator scan combined with beam excitations or through the use of local orbit bumps. In this paper, we show a first comparison of these methods in the same machine configuration, as well as a new very fast method based on a beam-based collimator alignment and a new faster variant of the collimator scan method. The methods are applied to the LHC operational configuration for 2015 at injection and with squeezed beams and the measured apertures are presented. | ||
| DOI • | reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-TUPMW014 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| TUPMW021 | Roman Pot Insertions in High-Intensity Beams for the CT-PPS Project at LHC | 1473 |
|
||
| The CMS-TOTEM Precision Proton Spectrometer (CT-PPS) at the LHC IP5 aims at exploring diffractive physics at high luminosity in standard LHC fills. It is based on 14 Roman Pots (RPs), designed to host tracking and time-of-flight detectors for measuring the kinematics of leading protons. To reach the physics goals, the RPs will finally have to approach the beams to distances of 15 beam σs (i.e. ~1.5 mm) or closer. After problems with showers and impedance heating in first high-luminosity RP insertions in 2012, the LS1 of LHC was used for upgrades in view of impedance minimisation and for adding new collimators to intercept RP-induced showers. In 2015 the effectiveness of these improvements was shown by successfully inserting the RPs in all LHC beam intensity steps to a first-phase distance of ~25 σs. This contribution reviews the measurements of debris showers and impedance effects, i.e. the data from Beam Loss Monitors, beam vacuum gauges and temperature sensors. The dependences of the observables on the luminosity are shown. Extrapolations to L=1034 cm-2 s-1 and smaller distances to the beam do not indicate any fundamental problems. The plans for 2016 are outlined. | ||
| DOI • | reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-TUPMW021 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| WEPMW007 | Validation of Off-momentum Cleaning Performance of the LHC Collimation System | 2427 |
|
||
| The LHC collimation system is designed to provide effective cleaning against losses coming from off-momentum particles, either due to un-captured beam or to an unexpected RF frequency change. For this reason the LHC is equipped with a hierarchy of collimators in IR3: primary, secondary and absorber collimators. After every collimator alignment or change of machine configuration the off-momentum cleaning efficiency is validated with loss maps at low intensity. We describe here the improved technique used in 2015 to generate such loss maps without completely dumping the beam into the collimators. The achieved performance of the collimation system for momentum cleaning is reviewed. | ||
| DOI • | reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-WEPMW007 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| WEPMW028 | First Attempts at using Active Halo Control at the LHC | 2486 |
|
||
|
Funding: Research supported by the High Luminosity LHC project. The beam halo population is a non-negligible factor for the performance of the LHC collimation system and the machine protection. In particular this could become crucial for aiming at stored beam energies of 700 MJ in the High Luminosity (HL-LHC) project, in order to avoid beam dumps caused by orbit jitter and to ensure safety during a crab cavity failure. Therefore several techniques to safely deplete the halo, i.e. active halo control, are under development. In a first attempt a novel way for safe halo depletion was tested with particle narrow-band excitation employing the LHC Transverse Damper (ADT). At an energy of 450 GeV a bunch selective beam tail scraping without affecting the core distribution was attempted. This paper presents the first measurement results, as well as a simple simulation to model the underlying dynamics. |
||
| DOI • | reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-WEPMW028 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| WEPMW029 | Simulation of Heavy-Ion Beam Losses with the SixTrack-FLUKA Active Coupling | 2490 |
| SUPSS008 | use link to see paper's listing under its alternate paper code | |
|
||
|
Funding: Work suppported by the Wolfgang Gentner Programme of the German BMBF The LHC heavy-ion program aims to further increase the stored ion beam energy, putting high demands on the LHC collimation system. Accurate simulations of the ion collimation efficiency are crucial to validate the feasibility of new proposed configurations and beam parameters. In this paper we present a generalized framework of the SixTrack-FLUKA coupling to simulate the fragmentation of heavy-ions in the collimators and their motion in the LHC lattice. We compare heavy-ion loss maps simulated on the basis of this framework with the loss distributions measured during heavy-ion operation in 2011 and 2015. |
||
| DOI • | reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-WEPMW029 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| WEPMW034 | First Operational Experience with Embedded Collimator BPMs in the LHC | 2510 |
|
||
| During Long Shutdown 1, 18 Large Hadron Collider (LHC) collimators were replaced with a new design, in which beam position monitor (BPM) pick-up buttons are embedded in the collimator jaws. The BPMs provide a direct measurement of the beam orbit at the collimators, and therefore can be used to align the collimators more quickly than using the standard technique which relies on feedback from beam losses. Online orbit measurements also mean that margins in the collimation hierarchy placed specifically to cater for unknown orbit drifts can be reduced, therefore increasing the beta-star and luminosity reach of the LHC. In this paper, the first operational results are presented, including a comparison with the standard alignment technique and a fill-to-fill analysis of the measured orbit in different machine modes in the first year of running after the shutdown. | ||
| DOI • | reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-WEPMW034 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |