IPAC2011 - List of Authors (Zickler, Th.)

Paper

Title

Page

Design and Optimization of the MedAustron Synchrotron Main Dipoles

2406

M. Stockner, B. Langenbeck, C. Siedler
EBG MedAustron, Wr. Neustadt, Austria
Th. Zickler
CERN, Geneva, Switzerland

MedAustron, a future centre for ion-therapy and research in Austria will comprise an accelerator facility based on a synchrotron for the delivery of protons and light ions for cancer treatment and for clinical and non-clinical research. The main dipole for the synchrotron went through an extensive design process to meet the stringent requirements. The local and integrated field quality was optimized. The residual field levels in the magnet gap were calculated and the dynamic behaviour of the dipole magnet was studied, both in 2D and 3D, using OPERA. The pole profile has been optimized to reduce sextupolar components in the integrated field by adjusting the shims on the pole edge. A Rogowski-profile at the pole ends and the use of stainless-steel tension straps will enhance the dynamic behaviour and guarantee a small time constants. Appropriate pole-end shimming will be used to compensate for residual multi-pole components and to fine-tune the magnetic length. The results of this comprehensive design study are summarized in this paper.

WEPO018

Status of the New Linac4 Magnets at CERN

2436

Th. Zickler, F. Borgnolutti, O. Crettiez, A. Newborough, L. Vanherpe
CERN, Geneva, Switzerland
A.S. Vorozhtsov
JINR, Dubna, Moscow Region, Russia

Linac4 is a new H⁻ linear accelerator at CERN replacing Linac2 as injector to the PS Booster. Almost 100 electro-magnets of different types are needed for the Linac4 project. Following a detailed analysis of the requirements and constraints, several magnet designs have been studied and are well advanced. This paper presents the design considerations, main parameters and characteristics of the new Linac4 magnets and summarizes the present status.

TUOAA03

The Linac4 Project at CERN

900

M. Vretenar, L. Arnaudon, P. Baudrenghien, C. Bertone, Y. Body, J.C. Broere, O. Brunner, M.C.L. Buzio, C. Carli, F. Caspers, J.-P. Corso, J. Coupard, A. Dallocchio, N. Dos Santos, R. Garoby, F. Gerigk, L. Hammouti, K. Hanke, M.A. Jones, I. Kozsar, J.-B. Lallement, J. Lettry, A.M. Lombardi, L.A. Lopez Hernandez, C. Maglioni, S.J. Mathot, S. Maury, B. Mikulec, D. Nisbet, C. Noels, M.M. Paoluzzi, B. Puccio, U. Raich, S. Ramberger, C. Rossi, N. Schwerg, R. Scrivens, G. Vandoni, J. Vollaire, S. Weisz, Th. Zickler
CERN, Geneva, Switzerland

As the first step of a long-term programme aiming at an increase in the LHC luminosity, CERN is building a new 160 MeV H⁻ linear accelerator, Linac4, to replace the ageing 50 MeV Linac2 as injector to the Proton-Synchrotron Booster (PSB). Linac4 is an 86-m long normal-conducting linac made of an H⁻ source, a Radio Frequency Quadrupole (RFQ), a chopping line and a sequence of three accelerating structures: a Drift-Tube Linac (DTL), a Cell-Coupled DTL (CCDTL) and a Pi-Mode Structure (PIMS). The civil engineering has been recently completed, and construction of the main accelerator components has started with the support of a network of international collaborations. The low-energy section up to 3 MeV including a 3-m long 352 MHz RFQ entirely built at CERN is in the final construction phase and is being installed on a dedicated test stand. The present schedule foresees beam commissioning of the accelerator in the new tunnel in 2013/14; the moment of connection of the new linac to the CERN accelerator chain will depend on the LHC schedule for long shut-downs.

Slides TUOAA03 [10.347 MB]

Paper	Title	Page
WEPO001	Design and Optimization of the MedAustron Synchrotron Main Dipoles	2406
	M. Stockner, B. Langenbeck, C. Siedler EBG MedAustron, Wr. Neustadt, Austria Th. Zickler CERN, Geneva, Switzerland
	MedAustron, a future centre for ion-therapy and research in Austria will comprise an accelerator facility based on a synchrotron for the delivery of protons and light ions for cancer treatment and for clinical and non-clinical research. The main dipole for the synchrotron went through an extensive design process to meet the stringent requirements. The local and integrated field quality was optimized. The residual field levels in the magnet gap were calculated and the dynamic behaviour of the dipole magnet was studied, both in 2D and 3D, using OPERA. The pole profile has been optimized to reduce sextupolar components in the integrated field by adjusting the shims on the pole edge. A Rogowski-profile at the pole ends and the use of stainless-steel tension straps will enhance the dynamic behaviour and guarantee a small time constants. Appropriate pole-end shimming will be used to compensate for residual multi-pole components and to fine-tune the magnetic length. The results of this comprehensive design study are summarized in this paper.

WEPO018	Status of the New Linac4 Magnets at CERN	2436
	Th. Zickler, F. Borgnolutti, O. Crettiez, A. Newborough, L. Vanherpe CERN, Geneva, Switzerland A.S. Vorozhtsov JINR, Dubna, Moscow Region, Russia
	Linac4 is a new H⁻ linear accelerator at CERN replacing Linac2 as injector to the PS Booster. Almost 100 electro-magnets of different types are needed for the Linac4 project. Following a detailed analysis of the requirements and constraints, several magnet designs have been studied and are well advanced. This paper presents the design considerations, main parameters and characteristics of the new Linac4 magnets and summarizes the present status.

TUOAA03	The Linac4 Project at CERN	900
	M. Vretenar, L. Arnaudon, P. Baudrenghien, C. Bertone, Y. Body, J.C. Broere, O. Brunner, M.C.L. Buzio, C. Carli, F. Caspers, J.-P. Corso, J. Coupard, A. Dallocchio, N. Dos Santos, R. Garoby, F. Gerigk, L. Hammouti, K. Hanke, M.A. Jones, I. Kozsar, J.-B. Lallement, J. Lettry, A.M. Lombardi, L.A. Lopez Hernandez, C. Maglioni, S.J. Mathot, S. Maury, B. Mikulec, D. Nisbet, C. Noels, M.M. Paoluzzi, B. Puccio, U. Raich, S. Ramberger, C. Rossi, N. Schwerg, R. Scrivens, G. Vandoni, J. Vollaire, S. Weisz, Th. Zickler CERN, Geneva, Switzerland
	As the first step of a long-term programme aiming at an increase in the LHC luminosity, CERN is building a new 160 MeV H⁻ linear accelerator, Linac4, to replace the ageing 50 MeV Linac2 as injector to the Proton-Synchrotron Booster (PSB). Linac4 is an 86-m long normal-conducting linac made of an H⁻ source, a Radio Frequency Quadrupole (RFQ), a chopping line and a sequence of three accelerating structures: a Drift-Tube Linac (DTL), a Cell-Coupled DTL (CCDTL) and a Pi-Mode Structure (PIMS). The civil engineering has been recently completed, and construction of the main accelerator components has started with the support of a network of international collaborations. The low-energy section up to 3 MeV including a 3-m long 352 MHz RFQ entirely built at CERN is in the final construction phase and is being installed on a dedicated test stand. The present schedule foresees beam commissioning of the accelerator in the new tunnel in 2013/14; the moment of connection of the new linac to the CERN accelerator chain will depend on the LHC schedule for long shut-downs.
	Slides TUOAA03 [10.347 MB]