IPAC2011 - List of Authors (Marhauser, F.)

Paper

Title

Page

Production and Testing Experience with the SRF Cavities for the CEBAF 12 GeV Upgrade

26

A. Burrill, G.K. Davis, F. Marhauser, C.E. Reece, A.V. Reilly, M. Stirbet
JLAB, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
The CEBAF recirculating CW electron linear accelerator at Jefferson Lab is presently undergoing a major upgrade to 12 GeV. This project includes the fabrication, preparation, and testing of 80 new 7-cell SRF cavities, followed by their incorporation into ten new cryomodules for subsequent testing and installation. In order to maximize the cavity Q over the full operable dynamic range in CEBAF (as high as 25 MV/m), the decision was taken to apply a streamlined preparation process that includes a final light temperature-controlled electropolish of the rf surface over the vendor-provided bulk BCP etch. Cavity processing work began at JLab in September 2010 and will continue through December 2011. The excellent performance results are exceeding project requirements and indicate a fabrication and preparation process that is stable and well controlled. The cavity production and performance experience to date will be summarized and lessons learned reported to the community.

Slides MOOCA01 [4.376 MB]

MOPC080

First Considerations Concerning an Optimized Cavity Design for the Main Linac of BERLinPro

259

B. Riemann, T. Weis
DELTA, Dortmund, Germany
W. Anders, J. Knobloch, A. Neumann
HZB, Berlin, Germany
H.-W. Glock, C. Potratz, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
F. Marhauser
JLAB, Newport News, Virginia, USA

Funding: work supported by BMBF under contracts 05K10PEA and 05K10HRC
The Berlin Energy Recovery Linac Project (BERLinPro) is designed to develop and demonstrate CW linac technology and expertise required to drive next-generation Energy Recovery Linacs. Strongly HOM-damped multicell 1.3 GHz cavities are required for the main linac. The optimization of the cavities presented here is primarily based on the CEBAF 1.5 GHz 5-cell high-current cavity design, including HOM waveguide couplers. The cavity was scaled to 1.3 GHz and extended to 7 cells. Modifications to the end group design have also been studied. An effort was also made to reduce the ratio Epk/Eacc while still permitting HOMs to propagate.

MOPC112

Fabrication and Testing Status of CEBAF 12 GeV Upgrade Cavities

337

F. Marhauser, A. Burrill, G.K. Davis, D. Forehand, C. Grenoble, J. Hogan, R.B. Overton, A.V. Reilly, R.A. Rimmer, M. Stirbet
JLAB, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
The 12 GeV upgrade of the Continuous Electron Beam Accelerator Facility (CEBAF) at Jefferson Laboratory (JLab) is under way. All cavities have been built by industry and are presently undergoing post-processing and final low and high power qualification before cryomodule assembly. The status is reported including fabrication-related experiences, observations and issues throughout production, post-processing and qualification.

MOPC113

Results of Cavity Series Fabrication at Jefferson Laboratory for the Cryomodule “R100”

340

F. Marhauser, W.A. Clemens, M.A. Drury, D. Forehand, J. Henry, S. Manning, R.B. Overton, R.S. Williams
JLAB, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
A series production of eight superconducting RF cavities for the cryomodule R100 was conducted at JLab in 2010. The cavities underwent chemical post-processing prior to vertical high power testing and routinely exceeded the envisaged performance specifications. After cryomodule assembly, cavities were successfully high power acceptance tested. In this paper, we present the achievements paving the way for the first demonstration of 100 MV (and beyond) in a single cryomodule to be operated at CEBAF.

MOPC114

Design, Fabrication and Testing of Medium-Beta 650 MHz SRF Cavity Prototypes for Project-X

343

F. Marhauser, W.A. Clemens, J. Henry, P. Kneisel, R. Martin, R.A. Rimmer, G. Slack, L. Turlington, R.S. Williams
JLAB, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
A new type of superconducting radio frequency (SRF) cavity shape with a shallow equator dome to reduce electron impact energies for suppressing multipacting barriers has been proposed. The shape is in consideration for the first time in the framework of Project-X to design a potential multi-cell cavity candidate for the medium-beta section of the SRF proton CW linac operating at 650 MHz. Rationales covering the design of the multi-cell cavity, the manufacture, post-processing and high power testing of two single-cell prototypes are presented.

MOPC115

JLab SRF Cavity Fabrication Errors, Consequences and Lessons Learned

346

F. Marhauser
JLAB, Newport News, Virginia, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177
Today, elliptical superconducting RF (SRF) cavities are preferably made from deep-drawn niobium sheets as pursued at Jefferson Laboratory (JLab). The fabrication of a cavity incorporates various cavity cell machining, trimming and electron beam welding (EBW) steps as well as surface chemistry that add to forming errors creating geometrical deviations of the cavity shape from its design. An analysis of in-house built cavities over the last years revealed significant errors in cavity production. Past fabrication flaws are described and lessons learned applied successfully to the most recent in-house series production of multi-cell cavities.

TUPS106

Absorber Materials at Room and Cryogenic Temperatures*

1792

F. Marhauser, T.S. Elliott, A.T. Wu
JLAB, Newport News, Virginia, USA
E.P. Chojnacki
CLASSE, Ithaca, New York, USA
E. Savrun
Sienna Technologies Inc., Woodinville, USA

Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177.
We recently reported on investigations of RF absorber materials at cryogenic temperatures conducted at Jefferson Laboratory (JLab). The work was initiated to find a replacement material for the 2 Kelvin low power waveguide Higher Order Mode (HOM) absorbers employed within the original cavity cryomodules of the Continuous Electron Beam Accelerator Facility (CEBAF). This effort eventually led to suitable candidates as reported in this paper. Furthermore, though constrained by small funds for labor and resources, we have analyzed a variety of lossy ceramic materials, several of which could be usable as HOM absorbers for both normal conducting and superconducting RF structures, e.g. as loads in cavity waveguides and beam tubes either at room or cryogenic temperatures and, depending on cooling measures, low to high operational power levels.

WEPC098

Automatic Pole and Q-Value Extraction for RF Structures

2241

C. Potratz, H.-W. Glock, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
F. Marhauser
JLAB, Newport News, Virginia, USA

The experimental characterization of RF structures like accelerating cavities often demands for measuring resonant frequencies of Eigenmodes and corresponding (loaded) Q-values over a wide spectral range. A common procedure to determine the Q-values is the -3dB method, which works well for isolated poles, but may not be applicable directly in case of multiple poles residing in close proximity (e.g. for adjacent transverse modes differing by polarization). Although alternative methods may be used in such cases, this often comes at the expense of inherent systematic errors. We have developed an automation algorithm, which not only speeds up the measurement time significantly, but is also able to extract Eigenfrequencies and Q-values both for well isolated and overlapping poles. At the same time the measurement accuracy may be improved as a major benefit. To utilize this procedure merely complex scattering parameters have to be recorded for the spectral range of interest. In this paper we present the proposed algorithm applied to experimental data recorded for superconducting higher-order-mode damped multi-cell cavities as an application of high importance.

Paper	Title	Page
MOOCA01	Production and Testing Experience with the SRF Cavities for the CEBAF 12 GeV Upgrade	26
	A. Burrill, G.K. Davis, F. Marhauser, C.E. Reece, A.V. Reilly, M. Stirbet JLAB, Newport News, Virginia, USA
	Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. The CEBAF recirculating CW electron linear accelerator at Jefferson Lab is presently undergoing a major upgrade to 12 GeV. This project includes the fabrication, preparation, and testing of 80 new 7-cell SRF cavities, followed by their incorporation into ten new cryomodules for subsequent testing and installation. In order to maximize the cavity Q over the full operable dynamic range in CEBAF (as high as 25 MV/m), the decision was taken to apply a streamlined preparation process that includes a final light temperature-controlled electropolish of the rf surface over the vendor-provided bulk BCP etch. Cavity processing work began at JLab in September 2010 and will continue through December 2011. The excellent performance results are exceeding project requirements and indicate a fabrication and preparation process that is stable and well controlled. The cavity production and performance experience to date will be summarized and lessons learned reported to the community.
	Slides MOOCA01 [4.376 MB]

MOPC080	First Considerations Concerning an Optimized Cavity Design for the Main Linac of BERLinPro	259
	B. Riemann, T. Weis DELTA, Dortmund, Germany W. Anders, J. Knobloch, A. Neumann HZB, Berlin, Germany H.-W. Glock, C. Potratz, U. van Rienen Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany F. Marhauser JLAB, Newport News, Virginia, USA
	Funding: work supported by BMBF under contracts 05K10PEA and 05K10HRC The Berlin Energy Recovery Linac Project (BERLinPro) is designed to develop and demonstrate CW linac technology and expertise required to drive next-generation Energy Recovery Linacs. Strongly HOM-damped multicell 1.3 GHz cavities are required for the main linac. The optimization of the cavities presented here is primarily based on the CEBAF 1.5 GHz 5-cell high-current cavity design, including HOM waveguide couplers. The cavity was scaled to 1.3 GHz and extended to 7 cells. Modifications to the end group design have also been studied. An effort was also made to reduce the ratio Epk/Eacc while still permitting HOMs to propagate.

MOPC112	Fabrication and Testing Status of CEBAF 12 GeV Upgrade Cavities	337
	F. Marhauser, A. Burrill, G.K. Davis, D. Forehand, C. Grenoble, J. Hogan, R.B. Overton, A.V. Reilly, R.A. Rimmer, M. Stirbet JLAB, Newport News, Virginia, USA
	Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. The 12 GeV upgrade of the Continuous Electron Beam Accelerator Facility (CEBAF) at Jefferson Laboratory (JLab) is under way. All cavities have been built by industry and are presently undergoing post-processing and final low and high power qualification before cryomodule assembly. The status is reported including fabrication-related experiences, observations and issues throughout production, post-processing and qualification.

MOPC113	Results of Cavity Series Fabrication at Jefferson Laboratory for the Cryomodule “R100”	340
	F. Marhauser, W.A. Clemens, M.A. Drury, D. Forehand, J. Henry, S. Manning, R.B. Overton, R.S. Williams JLAB, Newport News, Virginia, USA
	Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. A series production of eight superconducting RF cavities for the cryomodule R100 was conducted at JLab in 2010. The cavities underwent chemical post-processing prior to vertical high power testing and routinely exceeded the envisaged performance specifications. After cryomodule assembly, cavities were successfully high power acceptance tested. In this paper, we present the achievements paving the way for the first demonstration of 100 MV (and beyond) in a single cryomodule to be operated at CEBAF.

MOPC114	Design, Fabrication and Testing of Medium-Beta 650 MHz SRF Cavity Prototypes for Project-X	343
	F. Marhauser, W.A. Clemens, J. Henry, P. Kneisel, R. Martin, R.A. Rimmer, G. Slack, L. Turlington, R.S. Williams JLAB, Newport News, Virginia, USA
	Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. A new type of superconducting radio frequency (SRF) cavity shape with a shallow equator dome to reduce electron impact energies for suppressing multipacting barriers has been proposed. The shape is in consideration for the first time in the framework of Project-X to design a potential multi-cell cavity candidate for the medium-beta section of the SRF proton CW linac operating at 650 MHz. Rationales covering the design of the multi-cell cavity, the manufacture, post-processing and high power testing of two single-cell prototypes are presented.

MOPC115	JLab SRF Cavity Fabrication Errors, Consequences and Lessons Learned	346
	F. Marhauser JLAB, Newport News, Virginia, USA
	Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177 Today, elliptical superconducting RF (SRF) cavities are preferably made from deep-drawn niobium sheets as pursued at Jefferson Laboratory (JLab). The fabrication of a cavity incorporates various cavity cell machining, trimming and electron beam welding (EBW) steps as well as surface chemistry that add to forming errors creating geometrical deviations of the cavity shape from its design. An analysis of in-house built cavities over the last years revealed significant errors in cavity production. Past fabrication flaws are described and lessons learned applied successfully to the most recent in-house series production of multi-cell cavities.

TUPS106	Absorber Materials at Room and Cryogenic Temperatures*	1792
	F. Marhauser, T.S. Elliott, A.T. Wu JLAB, Newport News, Virginia, USA E.P. Chojnacki CLASSE, Ithaca, New York, USA E. Savrun Sienna Technologies Inc., Woodinville, USA
	Funding: Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177. We recently reported on investigations of RF absorber materials at cryogenic temperatures conducted at Jefferson Laboratory (JLab). The work was initiated to find a replacement material for the 2 Kelvin low power waveguide Higher Order Mode (HOM) absorbers employed within the original cavity cryomodules of the Continuous Electron Beam Accelerator Facility (CEBAF). This effort eventually led to suitable candidates as reported in this paper. Furthermore, though constrained by small funds for labor and resources, we have analyzed a variety of lossy ceramic materials, several of which could be usable as HOM absorbers for both normal conducting and superconducting RF structures, e.g. as loads in cavity waveguides and beam tubes either at room or cryogenic temperatures and, depending on cooling measures, low to high operational power levels.

WEPC098	Automatic Pole and Q-Value Extraction for RF Structures	2241
	C. Potratz, H.-W. Glock, U. van Rienen Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany F. Marhauser JLAB, Newport News, Virginia, USA
	The experimental characterization of RF structures like accelerating cavities often demands for measuring resonant frequencies of Eigenmodes and corresponding (loaded) Q-values over a wide spectral range. A common procedure to determine the Q-values is the -3dB method, which works well for isolated poles, but may not be applicable directly in case of multiple poles residing in close proximity (e.g. for adjacent transverse modes differing by polarization). Although alternative methods may be used in such cases, this often comes at the expense of inherent systematic errors. We have developed an automation algorithm, which not only speeds up the measurement time significantly, but is also able to extract Eigenfrequencies and Q-values both for well isolated and overlapping poles. At the same time the measurement accuracy may be improved as a major benefit. To utilize this procedure merely complex scattering parameters have to be recorded for the spectral range of interest. In this paper we present the proposed algorithm applied to experimental data recorded for superconducting higher-order-mode damped multi-cell cavities as an application of high importance.