IPAC2011 - List of Authors (Lari, L.)

Paper	Title	Page
THPZ032	Evaluation of the Combined Betatron and Momentum Cleaning in Point 3 in Terms of Cleaning Efficiency and Energy Deposition for the LHC Collimation Upgrade	3762
	L. Lari, R.W. Assmann, V. Boccone, M. Brugger, F. Cerutti, A. Ferrari, A. Rossi, R. Versaci, V. Vlachoudis, D. Wollmann CERN, Geneva, Switzerland A. Faus-Golfe, L. Lari IFIC, Valencia, Spain A. Mereghetti UMAN, Manchester, United Kingdom
	Funding: This work has been carried out through of the European Coordination for Accelerator Research and Development (EuCARD), co-sponsored by EU 7th Framework Program. The Phase I LHC Collimation System Upgrade could include moving part of the Betatron Cleaning from LHC Point 7 to Point 3 to improve both operation flexibility and intensity reach. In addition, the partial relocation of beam losses from the current Betatron cleaning region at Point 7 will mitigate the risks of Single Event Upsets to equipment installed in adjacent and partly not adequate shielded areas. A combined Betatron and Momentum Cleaning scenario at Point 3 implies the installation of new collimators and a new collimator aperture layout. This paper shows the whole LHC Collimator Efficiency variation with the new layout proposed at different beam energies. As part of the evaluation, energy deposition distribution in the IR3 region gives indications about the effect of this new implementation not only on the collimators themselves but also on the other beam line elements.

TUPS037	Preliminary Assessment of Beam Impact Consequences on LHC Collimators	1617
	M. Cauchi, R.W. Assmann, A. Bertarelli, R. Bruce, F. Carra, A. Dallocchio, D. Deboy, N. Mariani, A. Rossi, N.J. Sammut CERN, Geneva, Switzerland M. Cauchi, P. Mollicone UoM, Msida, Malta L. Lari IFIC, Valencia, Spain
	The correct functioning of the LHC collimation system is crucial to attain the desired LHC luminosity performance. However, the requirements to handle high intensity beams can be demanding. In this respect, the robustness of the collimators plays an important role. An accident which causes the proton beam to hit a collimator might result in severe beam-induced damage and, in some cases, replacement of the collimator, with consequent downtime for the machine. In this paper, several case studies representing different realistic beam impact scenarios are shown. A preliminary analysis of the thermal response of tertiary collimators to beam impact is presented, from which the most critical cases can be identified. Such work will also help to give an initial insight on the operational constraints of the LHC by taking into account all relevant collimator damage limits.

THPZ030	Halo Scrapings with Collimators in the LHC	3756
	F. Burkart, R.W. Assmann, R. Bruce, M. Cauchi, D. Deboy, S. Redaelli, A. Rossi, G. Valentino, D. Wollmann CERN, Geneva, Switzerland L. Lari IFIC, Valencia, Spain
	The population of the beam halo has been measured in the LHC with beam scraping experiments. Primary collimators of the LHC collimation system were used to scrape the beam halo at different statuses of the machine (injection, top energy, separated and colliding beams). In addition these measurements were used to calibrate the beam loss monitor signals to loss rates at the primary collimators. Within this paper the halo scraping method, the measured halo distribution and the calibration factors are presented and compared to theoretical predictions.

Paper

Title

Page

Evaluation of the Combined Betatron and Momentum Cleaning in Point 3 in Terms of Cleaning Efficiency and Energy Deposition for the LHC Collimation Upgrade

3762

L. Lari, R.W. Assmann, V. Boccone, M. Brugger, F. Cerutti, A. Ferrari, A. Rossi, R. Versaci, V. Vlachoudis, D. Wollmann
CERN, Geneva, Switzerland
A. Faus-Golfe, L. Lari
IFIC, Valencia, Spain
A. Mereghetti
UMAN, Manchester, United Kingdom

Funding: This work has been carried out through of the European Coordination for Accelerator Research and Development (EuCARD), co-sponsored by EU 7th Framework Program.
The Phase I LHC Collimation System Upgrade could include moving part of the Betatron Cleaning from LHC Point 7 to Point 3 to improve both operation flexibility and intensity reach. In addition, the partial relocation of beam losses from the current Betatron cleaning region at Point 7 will mitigate the risks of Single Event Upsets to equipment installed in adjacent and partly not adequate shielded areas. A combined Betatron and Momentum Cleaning scenario at Point 3 implies the installation of new collimators and a new collimator aperture layout. This paper shows the whole LHC Collimator Efficiency variation with the new layout proposed at different beam energies. As part of the evaluation, energy deposition distribution in the IR3 region gives indications about the effect of this new implementation not only on the collimators themselves but also on the other beam line elements.

TUPS037

Preliminary Assessment of Beam Impact Consequences on LHC Collimators

1617

M. Cauchi, R.W. Assmann, A. Bertarelli, R. Bruce, F. Carra, A. Dallocchio, D. Deboy, N. Mariani, A. Rossi, N.J. Sammut
CERN, Geneva, Switzerland
M. Cauchi, P. Mollicone
UoM, Msida, Malta
L. Lari
IFIC, Valencia, Spain

The correct functioning of the LHC collimation system is crucial to attain the desired LHC luminosity performance. However, the requirements to handle high intensity beams can be demanding. In this respect, the robustness of the collimators plays an important role. An accident which causes the proton beam to hit a collimator might result in severe beam-induced damage and, in some cases, replacement of the collimator, with consequent downtime for the machine. In this paper, several case studies representing different realistic beam impact scenarios are shown. A preliminary analysis of the thermal response of tertiary collimators to beam impact is presented, from which the most critical cases can be identified. Such work will also help to give an initial insight on the operational constraints of the LHC by taking into account all relevant collimator damage limits.

THPZ030

Halo Scrapings with Collimators in the LHC

3756

F. Burkart, R.W. Assmann, R. Bruce, M. Cauchi, D. Deboy, S. Redaelli, A. Rossi, G. Valentino, D. Wollmann
CERN, Geneva, Switzerland
L. Lari
IFIC, Valencia, Spain

The population of the beam halo has been measured in the LHC with beam scraping experiments. Primary collimators of the LHC collimation system were used to scrape the beam halo at different statuses of the machine (injection, top energy, separated and colliding beams). In addition these measurements were used to calibrate the beam loss monitor signals to loss rates at the primary collimators. Within this paper the halo scraping method, the measured halo distribution and the calibration factors are presented and compared to theoretical predictions.