IPAC2011 - List of Authors (Hsiung, G.-Y.)

Paper

Title

Page

Progress of the Construction for the TPS Vacuum System

976

G.-Y. Hsiung, C.K. Chan, C.H. Chang, C.-C. Chang, C.L. Chen, C.M. Cheng, Y.T. Cheng, S-N. Hsu, H.P. Hsueh, I.T. Huang, T.Y. Lee, I.C. Sheng, L.H. Wu, H.Y. Yan, Y.C. Yang, C.S. huang
NSRRC, Hsinchu, Taiwan
J.-R. Chen
National Tsing Hua University, Hsinchu, Taiwan

Vacuum system for the 3 GeV Taiwan Photon Source (TPS) has been started the construction since 2010. The critical components such as the bellows and gate valves with rf-contact shielding, pulsed magnet kicker ceramic chambers, BPM, crotch absorbers, etc. have been manufactured and tested. Aluminum alloy (Al-) vacuum chambers for the arc-cells have been machined and undergoing the in-house welding. Mass production of the vacuum equipments including the ion gauges, ion pumps, NEG pumps, and gate valves, has been contracted out and partially delivering following the schedule of the cell assembling. Each cell, contains two short Al-straight chambers and two Al-bending chambers, has been started the assembling and on-site welding on the pre-aligned girders in clean room forming an one-piece vacuum vessel about 14 m in length following by the vacuum baking to the ultra-high vacuum. The conceptual design of the vacuum systems for the long straight sections, the concentric booster, and the transport lines, will be addressed. The progress of prototyping development and the status of construction for the TPS vacuum system will be described in this paper.

Slides TUODB01 [35.595 MB]

TUPS029

Development of a Feedthrough with Small Reflection for the TPS BPM

1593

Huang, Y.T. Huang, C.-C. Chang, C.L. Chen, G.-Y. Hsiung, S-N. Hsu, H.P. Hsueh
NSRRC, Hsinchu, Taiwan
J.-R. Chen
National Tsing Hua University, Hsinchu, Taiwan

The TPS BPM feedthrough is a coaxial cable with a structure of a kind for which power loss occurs readily at places at which exists an impedance mismatch. With an impedance equation for a simple coaxial cable combined with a multi-dielectric modification, a model feedthrough with small reflection has been designed. With careful setting of brazing conditions and precise control of the dimensions of devices, a TPS prototypical BPM feedthrough having a reflection coefficient less than 0.05 was manufactured. The eccentricity was constrained within 0.03 mm, and the deviation of measured capacitance of button electrodes was less than 7 %.

TUPS030

Manufacturing and Vacuum Testing of Aluminum Bending Chambers for TPS

1596

Y.C. Yang, C.K. Chan, C.-C. Chang, C.L. Chen, J.-R. Chen, G.-Y. Hsiung, S-N. Hsu, T.Y. Lee
NSRRC, Hsinchu, Taiwan

The Taiwan Photon Source (TPS) is an aluminum alloy vacuum system with 518.4 m circumference divided into 24 sections. A6061T6 aluminum alloy material is used for TPS bending chambers. Each aluminum bending chamber is component of 2 half plates, about 3.5～4.2 m in length and～0.6 m in width, were oil-free CNC machined, ozone cleaned, and TIG welding in clean room. The deformation < 0.1 mm and leakage rate < 2x10-9mbar. L/s for each welded bending chamber has inspected and achieved. A bending chamber is inspecting the thermal outgassing rate test and ultimate pressure. The manufacturing and vacuum test will be described in this paper.

TUPS031

The Installation of One 14 Meter Cell of TPS Vacuum System

1599

H.P. Hsueh, C.K. Chan, C.H. Chang, C.-C. Chang, C.L. Chen, C.M. Cheng, Y.T. Cheng, G.-Y. Hsiung, S-N. Hsu, I.T. Huang, T.Y. Lee, H.Y. Yan, Y.C. Yang, C.S. huang
NSRRC, Hsinchu, Taiwan
J.-R. Chen
National Tsing Hua University, Hsinchu, Taiwan

The construction of a new 3 GeV synchrotron facility, Taiwan Photon Source, is ongoing. The vacuum system has been designed with off-site baking for arc section from sector gate valve to sector gate valve. There is no flange used in this arc section besides the two ends connected to sector gate valves. It is a tedious works for install such long vacuum system with aluminum chambers. In this poster, all the detailed installation procedures will be described. All the precaution inspection procedures for all vacuum components to prevent failed components to be installed will also be described. Every three weeks, one cell will be assembled and stored. Experience is being learned and could be used for the vacuum system of future new accelerator like FEL and others.

TUPS066

Design of Front End Safety Interlock System for Taiwan Photon Source

1689

H.Y. Yan, J.-R. Chen, G.-Y. Hsiung, C.K. Kuan, I.C. Sheng, Z.-D. Tsai
NSRRC, Hsinchu, Taiwan

Safety interlock is one of critical subsystems in synchrotron radiation accelerator. A front end (FE) interlock prototype system has been designed, fabricated, and initially tested for Taiwan Photon Source (TPS). TPS FE interlock logic is designed based on that of Taiwan Light Source (TLS), and moderately modified due to the accelerator parameter discrepancy between TPS and TLS. The programmable automation controllers (PAC) have been utilized in FE safety interlock system for their reliability, convenience, processing capability, communication, and stability in user interface. In FE PAC system, touch panels are used as the graphical user interface (GUI) to control and monitor FE components. In addition, with GUI control it is used to beam position monitoring devices as well as confined beam sizes aperture for beam line users. The interlock design such as data acquisition and parameters monitoring for vacuum pressure, flow rate of cooling water, pressure of compressive air, chamber and water temperature, and overall interlock logic are also presented in this paper.

TUPS067

Photon-stimulated Desorption Experiment for a TPS Crotch Absorber

1692

Y.T. Cheng, G.-Y. Hsiung, C.K. Kuan, A. Sheng, H.Y. Yan
NSRRC, Hsinchu, Taiwan
J.-R. Chen
National Tsing Hua University, Hsinchu, Taiwan

National Synchrotron Radiation Research Center (NSRRC) is constructing a large third-generation synchrotron accelerator in Taiwan, the so-called Taiwan Photon Source (TPS). This 3-GeV, 500-mA machine will generate high-density bending-magnet radiation, of which 90 % of the power is absorbed by the crotch absorber in the storage ring. To understand better the beam-cleaning and photon-desorption phenomena of a copper crotch absorber, we have performed a PSD (photon-stimulated desorption) test in Taiwan Light Source (TLS) at Beam line 19 (BL19). Some mathematical modelling, experimental designs and results are also presented here.

Paper	Title	Page
TUODB01	Progress of the Construction for the TPS Vacuum System	976
	G.-Y. Hsiung, C.K. Chan, C.H. Chang, C.-C. Chang, C.L. Chen, C.M. Cheng, Y.T. Cheng, S-N. Hsu, H.P. Hsueh, I.T. Huang, T.Y. Lee, I.C. Sheng, L.H. Wu, H.Y. Yan, Y.C. Yang, C.S. huang NSRRC, Hsinchu, Taiwan J.-R. Chen National Tsing Hua University, Hsinchu, Taiwan
	Vacuum system for the 3 GeV Taiwan Photon Source (TPS) has been started the construction since 2010. The critical components such as the bellows and gate valves with rf-contact shielding, pulsed magnet kicker ceramic chambers, BPM, crotch absorbers, etc. have been manufactured and tested. Aluminum alloy (Al-) vacuum chambers for the arc-cells have been machined and undergoing the in-house welding. Mass production of the vacuum equipments including the ion gauges, ion pumps, NEG pumps, and gate valves, has been contracted out and partially delivering following the schedule of the cell assembling. Each cell, contains two short Al-straight chambers and two Al-bending chambers, has been started the assembling and on-site welding on the pre-aligned girders in clean room forming an one-piece vacuum vessel about 14 m in length following by the vacuum baking to the ultra-high vacuum. The conceptual design of the vacuum systems for the long straight sections, the concentric booster, and the transport lines, will be addressed. The progress of prototyping development and the status of construction for the TPS vacuum system will be described in this paper.
	Slides TUODB01 [35.595 MB]

TUPS029	Development of a Feedthrough with Small Reflection for the TPS BPM	1593
	Huang, Y.T. Huang, C.-C. Chang, C.L. Chen, G.-Y. Hsiung, S-N. Hsu, H.P. Hsueh NSRRC, Hsinchu, Taiwan J.-R. Chen National Tsing Hua University, Hsinchu, Taiwan
	The TPS BPM feedthrough is a coaxial cable with a structure of a kind for which power loss occurs readily at places at which exists an impedance mismatch. With an impedance equation for a simple coaxial cable combined with a multi-dielectric modification, a model feedthrough with small reflection has been designed. With careful setting of brazing conditions and precise control of the dimensions of devices, a TPS prototypical BPM feedthrough having a reflection coefficient less than 0.05 was manufactured. The eccentricity was constrained within 0.03 mm, and the deviation of measured capacitance of button electrodes was less than 7 %.

TUPS030	Manufacturing and Vacuum Testing of Aluminum Bending Chambers for TPS	1596
	Y.C. Yang, C.K. Chan, C.-C. Chang, C.L. Chen, J.-R. Chen, G.-Y. Hsiung, S-N. Hsu, T.Y. Lee NSRRC, Hsinchu, Taiwan
	The Taiwan Photon Source (TPS) is an aluminum alloy vacuum system with 518.4 m circumference divided into 24 sections. A6061T6 aluminum alloy material is used for TPS bending chambers. Each aluminum bending chamber is component of 2 half plates, about 3.5～4.2 m in length and～0.6 m in width, were oil-free CNC machined, ozone cleaned, and TIG welding in clean room. The deformation < 0.1 mm and leakage rate < 2x10-9mbar. L/s for each welded bending chamber has inspected and achieved. A bending chamber is inspecting the thermal outgassing rate test and ultimate pressure. The manufacturing and vacuum test will be described in this paper.

TUPS031	The Installation of One 14 Meter Cell of TPS Vacuum System	1599
	H.P. Hsueh, C.K. Chan, C.H. Chang, C.-C. Chang, C.L. Chen, C.M. Cheng, Y.T. Cheng, G.-Y. Hsiung, S-N. Hsu, I.T. Huang, T.Y. Lee, H.Y. Yan, Y.C. Yang, C.S. huang NSRRC, Hsinchu, Taiwan J.-R. Chen National Tsing Hua University, Hsinchu, Taiwan
	The construction of a new 3 GeV synchrotron facility, Taiwan Photon Source, is ongoing. The vacuum system has been designed with off-site baking for arc section from sector gate valve to sector gate valve. There is no flange used in this arc section besides the two ends connected to sector gate valves. It is a tedious works for install such long vacuum system with aluminum chambers. In this poster, all the detailed installation procedures will be described. All the precaution inspection procedures for all vacuum components to prevent failed components to be installed will also be described. Every three weeks, one cell will be assembled and stored. Experience is being learned and could be used for the vacuum system of future new accelerator like FEL and others.

TUPS066	Design of Front End Safety Interlock System for Taiwan Photon Source	1689
	H.Y. Yan, J.-R. Chen, G.-Y. Hsiung, C.K. Kuan, I.C. Sheng, Z.-D. Tsai NSRRC, Hsinchu, Taiwan
	Safety interlock is one of critical subsystems in synchrotron radiation accelerator. A front end (FE) interlock prototype system has been designed, fabricated, and initially tested for Taiwan Photon Source (TPS). TPS FE interlock logic is designed based on that of Taiwan Light Source (TLS), and moderately modified due to the accelerator parameter discrepancy between TPS and TLS. The programmable automation controllers (PAC) have been utilized in FE safety interlock system for their reliability, convenience, processing capability, communication, and stability in user interface. In FE PAC system, touch panels are used as the graphical user interface (GUI) to control and monitor FE components. In addition, with GUI control it is used to beam position monitoring devices as well as confined beam sizes aperture for beam line users. The interlock design such as data acquisition and parameters monitoring for vacuum pressure, flow rate of cooling water, pressure of compressive air, chamber and water temperature, and overall interlock logic are also presented in this paper.

TUPS067	Photon-stimulated Desorption Experiment for a TPS Crotch Absorber	1692
	Y.T. Cheng, G.-Y. Hsiung, C.K. Kuan, A. Sheng, H.Y. Yan NSRRC, Hsinchu, Taiwan J.-R. Chen National Tsing Hua University, Hsinchu, Taiwan
	National Synchrotron Radiation Research Center (NSRRC) is constructing a large third-generation synchrotron accelerator in Taiwan, the so-called Taiwan Photon Source (TPS). This 3-GeV, 500-mA machine will generate high-density bending-magnet radiation, of which 90 % of the power is absorbed by the crotch absorber in the storage ring. To understand better the beam-cleaning and photon-desorption phenomena of a copper crotch absorber, we have performed a PSD (photon-stimulated desorption) test in Taiwan Light Source (TLS) at Beam line 19 (BL19). Some mathematical modelling, experimental designs and results are also presented here.