| Paper | Title | Page |
|---|---|---|
| MOPCH024 | Future Seeding Experiments at SPARC | 95 |
|
||
| Sources based on High order Harmonics Generated in gases (HHG) with high power Ti:Sa lasers pulses represent promising candidates as seed for FEL amplifiers for several reasons, as spatial and temporal coherence, wavelength tunability and spectral range, which extends down to the nm wavelength scale. This communication describes the research work plan that is under implementation at the SPARC FEL facility in the framework of the EUROFEL programme. The main goal of the collaboration is to study and test the amplification and the FEL harmonic generation process of an input seed signal obtained as higher order harmonics generated both in crystals (400 nm and 266 nm) and in gases (266 nm, 160 nm, 114 nm). The SPARC FEL can be configured to test several cascaded FEL layouts that will be analysed in this contribution. | ||
| MOPCH028 | Status of the SPARX FEL Project | 107 |
|
||
| The SPARX project consists in an X-ray-FEL facility jointly supported by MIUR (Research Department of Italian Government), Regione Lazio, CNR, ENEA, INFN and Rome University Tor Vergata. It is the natural extension of the ongoing activities of the SPARC collaboration. The aim is the generation of electron beams characterized by ultra-high peak brightness at the energy of 1 and 2 GeV, for the first and the second phase respectively. The beam is expected to drive a single pass FEL experiment in the range of 13.5-6 nm and 6-1.5 nm, at 1 GeV and 2 GeV respectively, both in SASE and SEEDED FEL configurations. A hybrid scheme of RF and magnetic compression will be adopted, based on the expertise achieved at the SPARC high brightness photoinjector presently under commissioning at Frascati INFN-LNF Laboratories. The use of superconducting and exotic undulator sections will be also exploited. In this paper we report the progress of the collaboration together with start to end simulation results based on a combined scheme of RF compression techniques. | ||
| MOPCH029 | Status of the SPARC Project | 110 |
|
||
| The SPARC Project is starting the commissioning of its photo-injector. RF gun, RF sources, RF network and control, power supplies, emittance meter, beam diagnostics and control to measure the RF gun beam are installed. The photocathode drive laser has been characterized in terms of pulse shape and quality. We expect to conduct beam measurements at RF gun exit in the next future and consequently to start the installation of accelerating sections. The design of the 12 m undulator for the FEL experiment has been completed and the first undulator section out of 6 is under construction: we expect to characterize it at Frascati ENEA laboratory within the next months. SPARC as a facility will host FEL experiments using SASE, seeding and non-linear resonant harmonics. Additional R&D on X-band and S-band structures for velocity bunching are in progress, as well as studies on new photocathode materials and exotic undulator designs. We also present studies on solenoid field defects, beam based alignments, exotic electron bunch production (blow-out of short laser pulses or intensity modulated laser pulses). The possible use of segmented superconducting micro-undulators will be discussed too. | ||
| MOPCH026 | A Biperiodic X-band RF Cavity for SPARC | 101 |
|
||
| The Frascati photo-injector SPARC (Pulsed Self Amplified Coherent Radiation Source) will be equipped with an X-band RF cavity for linearizing emittance to enhance bunch compression and for reducing bunch longitudinal energy spread. A biperiodic cavity working on the pi/2-mode offers some advantages in comparison to a conventional (periodic) cavity despite the need of accurate machining. A copper prototype made of 17 separated cells has been built following numerical simulation. In this paper we report on preliminary measurements of its RF properties. The main characteristics of the cooling system for the final device are also addressed. | ||
| MOPCH031 | Progress on the Pi-mode X-band RF Cavity for SPARC | 116 |
|
||
|
The Frascati photo-injector SPARC (Pulsed Self Amplified Coherent Radiation Source) will be equipped with an x-band RF cavity for linearizing emittance to enhance bunch compression and for reducing bunch longitudinal energy spread. The nine cell standing wave cavity prototype made of separated cells has been already built and measured*. In this paper we report on characterization of the first brazed prototype. Heat load studies have been performed as well to design the cooling system for the final device.
*D. Alesini et al. Nucl. Instr. and Meth. A 554 (2005) 1. |
||
| WEPCH022 | Study of the Effect of Multipolar Components in the SPARC Emittance Compensation Gun Solenoid | 1969 |
|
||
| The SPARC photoinjector rf gun requires a solenoid immediately downstream for emittance compensation. The analysis of the measured solenoid magnetic maps shows the existence of multipolar components added to the pure solenoid field. The effect of these added fields on beam dynamics and possible correction schemes have been studied from the theoretical point of view and by numerical calculations based on PARMELA/TREDI codes. An accurate 3D numerical modelization by using CST EM Studio has been done, in order to investigate the source of these multipolar components and to suggest some design modifications aimed to reduce their magnitude. The results of this study are presented here. | ||
| WEPLS021 | The PLASMONX Project for Advanced Beam Physics Experiments | 2439 |
|
||
| The Project PLASMONX is well progressing into its design phase and has entered as well its second phase of procurements for main components. The project foresees the installation at LNF of a Ti:Sa laser system (peak power > 170 TW), synchronized to the high brightness electron beam produced by the SPARC photo-injector. The advancement of the procurement of such a laser system is reported, as well as the construction plans of a new building at LNF to host a dedicated laboratory for high intensity photon beam experiments (High Intensity Laser Laboratory). Several experiments are foreseen using this complex facility, mainly in the high gradient plasma acceleration field and in the field of mono-chromatic ultra-fast X-ray pulse generation via Thomson back-scattering. We present an innovative scheme of external injection of the SPARC beam into laser wake-field driven plasma waves. Detailed numerical simulations have been carried out to study the generation of short electron bunches, to be injected into plasma waves driven with adiabatically variable density in order to compress the bunch at injection and further accelerate it by preserving a small energy spread and good beam quality. | ||
| WEPLS049 | The Design of a Hybrid Photoinjector for High Brightness Beam Applications | 2487 |
|
||
| In this paper, we illustrate the electromagnetic and beam dynamics design procedure of a new class of photoinjector, a hybrid standing/traveling wave structure. In this device a standing wave RF gun section is integrated with a downstream traveling wave structure through a coupling cell that feeds simultaneously the two sections. We discuss the advantages in RF and beam performance of the hybrid photoinjector compared to conventional systems. The electromagnetic design has been performed using the 2D and 3D electromagnetic codes Superfish and HFSS. Results of beam dynamics simulations in different operating conditions are also discussed. | ||
| THPLS098 | Optimum Beam Creation in Photoinjectors Using Space-charge Expansion | 0 |
|
||
|
It has recently been shown by Luiten* that by illuminating a photocathode with an ultra-short laser pulse of appropriate transverse profile, a uniform density, ellipsoidally shaped bunch is dynamically formed, which then has linear space-charge fields in all dimensions inside of the bunch. We study here this process, and its marriage to the standard emittance compensation scenario that is implemented in most modern photoinjectors. It is seen that the two processes are compatible, with simulations indicating that a very high brightness beam can be obtained. The scheme has produced stimulus for an experiment at the SPARC injector at Frascati in 2006. We review preparations for this experiment, and discuss the measurable quantities and their appropriate diagnosis, including the time-resolved observation of ellipsoidal beam shape at low energy. A scheme based on gating of Cerenkov radiation produced at an Aerogel for time-resolved measurements is proposed. Future measurements at high energy based on fs resolution RF sweepers are discussed. The prospects for using the very low longitudinal emittance beam in a future bunch compressor for producing 10 micron long beams are evaluated.
*O. J. Luiten et al. Physical Review Letters, 93, 094802-1 (2004). |
||
| THPLS105 | Characterization of the SPARC Photo-injector with the Movable Emittance Meter | 3523 |
|
||
| As a first stage of the commissioning of SPARC accelerator a complete characterization of the photo-injector is planned. The objective is the optimization of the RF-gun setting that best matches the design working point and, generally, a detailed study of the emittance compensation process providing the optimal value of emittance at the end of the linac. For this purpose a novel beam diagnostic, the emittance-meter, consisting of a movable emittance measurement system, was conceived and built. This paper presents the results of the first measurements with the emittance-meter showing the characteristics and the performance at the SPARC photo-injector. |