PAC2013 - List of Authors (Somaschini, L.)

Paper	Title	Page
WEPMA03	Tuner System Assembly and Tests for the 201-MHz MICE Cavity	987
	L. Somaschini INFN-Pisa, Pisa, Italy A.J. DeMello, D. Li, S.P. Virostek LBNL, Berkeley, California, USA P.M. Hanlet IIT, Chicago, Illinois, USA A. Moretti, R.J. Pasquinelli, D.W. Peterson, Y. Torun Fermilab, Batavia, USA
	Funding: Supported by the US Department of Energy. The MICE cavities include a mechanical tuning system consisting of stainless steel flexure forks attached to the cavity body and driven by pneumatic actuators. The first of these systems was assembled and tested at Fermilab for use at the MuCool Test Area. The actuators were calibrated on a test hoop. The cavity body was measured and the fork contact pads machined to fit. Actuators were mounted on the vacuum vessel housing the cavity. The transfer function of the tuning system was measured and frequency control software implemented.

WEPMA16	Assembly and Testing of the First 201-MHz MICE Cavity at Fermilab	1016
	Y. Torun Illinois Institute of Technology, Chicago, IL, USA D.L. Bowring, A.J. DeMello, D. Li, T.H. Luo, S.P. Virostek LBNL, Berkeley, California, USA P.M. Hanlet IIT, Chicago, Illinois, USA M.A. Leonova, A. Moretti, R.J. Pasquinelli, D.W. Peterson, R.P. Schultz, J.T. Volk Fermilab, Batavia, USA T.H. Luo UMiss, University, Mississippi, USA L. Somaschini INFN-Pisa, Pisa, Italy
	Funding: Supported by the US Department of Energy. The International Muon Ionization Cooling Experiment (MICE) includes two linear accelerator sections with four RF cavities each within a shared vacuum vessel. Ten cavity bodies have been fabricated for MICE including two spares and one was electropolished. A special vacuum vessel was built to house this cavity and form the 201-MHz Single-Cavity Module. The module was assembled, instrumented and tested at Fermilab for installation and operation in the MuCool Test Area.

Paper

Title

Page

Tuner System Assembly and Tests for the 201-MHz MICE Cavity

987

L. Somaschini
INFN-Pisa, Pisa, Italy
A.J. DeMello, D. Li, S.P. Virostek
LBNL, Berkeley, California, USA
P.M. Hanlet
IIT, Chicago, Illinois, USA
A. Moretti, R.J. Pasquinelli, D.W. Peterson, Y. Torun
Fermilab, Batavia, USA

Funding: Supported by the US Department of Energy.
The MICE cavities include a mechanical tuning system consisting of stainless steel flexure forks attached to the cavity body and driven by pneumatic actuators. The first of these systems was assembled and tested at Fermilab for use at the MuCool Test Area. The actuators were calibrated on a test hoop. The cavity body was measured and the fork contact pads machined to fit. Actuators were mounted on the vacuum vessel housing the cavity. The transfer function of the tuning system was measured and frequency control software implemented.

WEPMA16

Assembly and Testing of the First 201-MHz MICE Cavity at Fermilab

1016

Y. Torun
Illinois Institute of Technology, Chicago, IL, USA
D.L. Bowring, A.J. DeMello, D. Li, T.H. Luo, S.P. Virostek
LBNL, Berkeley, California, USA
P.M. Hanlet
IIT, Chicago, Illinois, USA
M.A. Leonova, A. Moretti, R.J. Pasquinelli, D.W. Peterson, R.P. Schultz, J.T. Volk
Fermilab, Batavia, USA
T.H. Luo
UMiss, University, Mississippi, USA
L. Somaschini
INFN-Pisa, Pisa, Italy

Funding: Supported by the US Department of Energy.
The International Muon Ionization Cooling Experiment (MICE) includes two linear accelerator sections with four RF cavities each within a shared vacuum vessel. Ten cavity bodies have been fabricated for MICE including two spares and one was electropolished. A special vacuum vessel was built to house this cavity and form the 201-MHz Single-Cavity Module. The module was assembled, instrumented and tested at Fermilab for installation and operation in the MuCool Test Area.