Fermilab, Batavia
TRIUMF, Vancouver
Muons, Inc, Batavia
JLAB, Newport News, Virginia
Modern technology allows us to consider operating an 8 GeV Linac in a cw mode to accelerate a high-current H- beam. By using appropriate accumulation rings, the linac could provide simultaneous beams for direct neutrino production, neutrino factories, fixed target experiments, and muon colliders. Several other unique accelerator applications could also be served and improved by the same continuous beam, including studies of energy production and nuclear waste reduction by transmutation, rare muon decay searches, and muon catalyzed fusion. The trade-offs between cw operation compared to pulsed operation that are considered include the maximum rf gradient and corresponding linac length or energy, the rf frequency, rf peak power and coupler requirements, and refrigeration. Methods for accumulating the beam from a cw linac to serve the special needs of the potential future Fermilab programs mentioned above are considered. In this paper we also examine the use of a cyclotron as a source of high current beams to reduce the cost and complexity of the linac front end.
Fermilab, Batavia
Funding: Operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
3.9 GHz SRF cavities have been built and tested at Fermilab for use in the DESY FLASH facility. Six cavities have undergone testing in various scenarios. Comparisons of performance in these different conditions, from bare cavities in a vertical dewar to 'dressed' in the horizontal test stand and intermediate test configurations are presented. We also report on analysis of expected maximum performance and an estimate of same.
Fermilab, Batavia
Following development and testing a prototype waveguide-based high power phase shifter, a design concept of a high power fast phase shifter has been developed. The shifter uses ferrite blocks positioned in a rectangular waveguide. The waveguide cross-section is chosen to suppress most of resonances that could otherwise be a limiting factor for the phase shifter high power performance. Base bias field is created with the use of permanent magnets. Low inductance coils in the same magnetic circuit excite fast (pulsed) bias field component. The waveguide is designed in a way to ensure that the pulsed magnetic field penetrates inside the waveguide with minimum delay while allowing effective heat extraction from the ferrite blocks. This report provides details of the system design, including expected rf behavior and frequency range.
Fermilab, Batavia
University of Udine, Udine
Funding: This work was supported by Fermilab Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
The 3.9 GHz 3rd harmonic cavities are designed to serve as compensation devices for improving the longitudinal emittance of the free-electron laser FLASH at DESY. These cavities operate in the TM010 mode, and will be located between the injector and the accelerating cavities. Fermilab is obligated to provide DESY with a cryomodule containing four 3rd harmonic cavities. In this paper we discuss the process of welding helium vessels to these cavities. Included will be a description of the joint designs and weld preparations, development of the weld parameters, and the procedure for monitoring the frequency spectrum during TIG welding to prevent the cavity from undergoing plastic deformation. Also discussed will be issues related to qualifying the dressed cavities as exceptional vessels (relative to the ASME Boiler and Pressure Vessel Code) for horizontal testing and eventual installation at DESY, due to the necessary use of non-ASME code materials and non-full penetration electron beam welds.
Fermilab, Batavia
Funding: Operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
Fermilab is involved in an effort to design, build, test and deliver four 3.9 GHz superconducting rf cavities within a single cryomodule to be delivered to DESY as a 'third harmonic' structure for the FLASH facility to improve the longitudinal emittance. In addition to an overall status update we will present recent results from single 'dressed' cavity horizontal tests and shipping and alignment measurements.
