IPAC2015 - List of Authors (Lill, R.M.)

Paper	Title	Page
MOPWI010	Design and Development of a Beam Stablity Mechanical Motion System Diagnostic for the APS MBA Upgrade	1164
	R.M. Lill, G. Decker, N. Sereno, B.X. Yang ANL, Argonne, Ilinois, USA
	Funding: Results shown in this report result from work performed at Argonne National Laboratory operated by UChicago Argonne, LLC, for the U.S. Department of Energy under contract DE-AC02-06CH11357. The Advanced Photon Source (APS) is currently in the conceptual design phase for the MBA lattice upgrade. In order to achieve long-term beam stability goals, a Mechanical Motion System (MMS) has been designed to monitor critical in-tunnel beam position monitoring devices. The mechanical motion generated from changes in chamber cooling water temperature, tunnel air temperature, beam current and undulator gap positon causes erroneous changes in beam position measurements causing drift in the X-ray beam position. The MMS has been prototyped and presently provides critical information on the vacuum chamber and BPM support systems. We report on first results of the prototype system installed in the APS storage ring.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPWI010
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPWI011	Beam Stability R&D for the APS MBA Upgrade	1167
	N. Sereno, N.D. Arnold, H. Bui, J. Carwardine, G. Decker, L. Emery, R.I. Farnsworth, R.T. Keane, F. Lenkszus, R.M. Lill, R. Lipa, S. Veseli, S. Xu, B.X. Yang ANL, Argonne, Ilinois, USA
	Funding: Results shown in this report result from work performed at Argonne National Laboratory operated by UChicago Argonne, LLC, for the U.S. Department of Energy under contract DE-AC02-06CH11357. Beam diagnostics required for the APS MBA are driven by ambitious beam stability requirements. The major AC stability challenge is to correct rms beam motion to 10% the rms beam size at the insertion device source points from 0.01 to 1000 Hz. The vertical plane represents the biggest challenge for AC stability which is required to be 400 nm rms for a 4 micron vertical beam size. Long term drift over a period of 7 days is required to be 1 micron or less. Major diagnostics R&D components are improved rf beam position processing using commercially available fpga based bpm processors, new XRay beam position monitors sensitive only to hard X-rays, mechanical motion sensing and remediation to detect and correct long term drift and a new feedback system featuring a tenfold increase in sampling rate and a several-fold increase in the number of fast correctors and bpms. Feedback system development represents a major effort and we are pursuing development of a novel algorithm that integrates orbit correction for both slow and fast correctors down to DC simultaneously. Finally a new data acquisition system (DAQ) is being developed to acquire streaming data from all diagnostics.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPWI011
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPWI012	Conceptual Design and Analysis of a Storage Ring Beam Position Monitor for the APS Upgrade	1170
	B.K. Stillwell, R.M. Lill, R.R. Lindberg, M.M. O'Neill, B.G. Rocke, X. Sun ANL, Argonne, Ilinois, USA A. Blednykh BNL, Upton, Long Island, New York, USA
	Funding: Created by UChicago Argonne, LLC, operator of Argonne National Laboratory, a U.S. Department of Energy Office of Science laboratory operated under Contract No. DE-AC02-06CH11357. A conceptual design has been developed for a radio frequency (rf) pickup-type beam position monitor (BPM) for use in a multi-bend achromat (MBA) storage ring under consideration by the APS Upgrade project (APS-U). Beam feedback systems are expected to require fourteen rf BPMs per sector with exceptional sensitivity and mechanical stability. Simultaneously, BPM insertion length must be minimized to allow lattice designers the greatest freedom in selecting magnet lengths and locations. Envisioned is a conventional four probe arrangement integrated inside of a pair of rf-shielded bellows for mechanical isolation. Basic aspects of the design are presented along with the results of analyses which establish expected mechanical, electronic, and beam physics-related performance measures.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPWI012
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Design and Development of a Beam Stablity Mechanical Motion System Diagnostic for the APS MBA Upgrade

1164

R.M. Lill, G. Decker, N. Sereno, B.X. Yang
ANL, Argonne, Ilinois, USA

Funding: Results shown in this report result from work performed at Argonne National Laboratory operated by UChicago Argonne, LLC, for the U.S. Department of Energy under contract DE-AC02-06CH11357.
The Advanced Photon Source (APS) is currently in the conceptual design phase for the MBA lattice upgrade. In order to achieve long-term beam stability goals, a Mechanical Motion System (MMS) has been designed to monitor critical in-tunnel beam position monitoring devices. The mechanical motion generated from changes in chamber cooling water temperature, tunnel air temperature, beam current and undulator gap positon causes erroneous changes in beam position measurements causing drift in the X-ray beam position. The MMS has been prototyped and presently provides critical information on the vacuum chamber and BPM support systems. We report on first results of the prototype system installed in the APS storage ring.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPWI010

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPWI011

Beam Stability R&D for the APS MBA Upgrade

1167

N. Sereno, N.D. Arnold, H. Bui, J. Carwardine, G. Decker, L. Emery, R.I. Farnsworth, R.T. Keane, F. Lenkszus, R.M. Lill, R. Lipa, S. Veseli, S. Xu, B.X. Yang
ANL, Argonne, Ilinois, USA

Funding: Results shown in this report result from work performed at Argonne National Laboratory operated by UChicago Argonne, LLC, for the U.S. Department of Energy under contract DE-AC02-06CH11357.
Beam diagnostics required for the APS MBA are driven by ambitious beam stability requirements. The major AC stability challenge is to correct rms beam motion to 10% the rms beam size at the insertion device source points from 0.01 to 1000 Hz. The vertical plane represents the biggest challenge for AC stability which is required to be 400 nm rms for a 4 micron vertical beam size. Long term drift over a period of 7 days is required to be 1 micron or less. Major diagnostics R&D components are improved rf beam position processing using commercially available fpga based bpm processors, new XRay beam position monitors sensitive only to hard X-rays, mechanical motion sensing and remediation to detect and correct long term drift and a new feedback system featuring a tenfold increase in sampling rate and a several-fold increase in the number of fast correctors and bpms. Feedback system development represents a major effort and we are pursuing development of a novel algorithm that integrates orbit correction for both slow and fast correctors down to DC simultaneously. Finally a new data acquisition system (DAQ) is being developed to acquire streaming data from all diagnostics.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPWI011

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPWI012

Conceptual Design and Analysis of a Storage Ring Beam Position Monitor for the APS Upgrade

1170

B.K. Stillwell, R.M. Lill, R.R. Lindberg, M.M. O'Neill, B.G. Rocke, X. Sun
ANL, Argonne, Ilinois, USA
A. Blednykh
BNL, Upton, Long Island, New York, USA

Funding: Created by UChicago Argonne, LLC, operator of Argonne National Laboratory, a U.S. Department of Energy Office of Science laboratory operated under Contract No. DE-AC02-06CH11357.
A conceptual design has been developed for a radio frequency (rf) pickup-type beam position monitor (BPM) for use in a multi-bend achromat (MBA) storage ring under consideration by the APS Upgrade project (APS-U). Beam feedback systems are expected to require fourteen rf BPMs per sector with exceptional sensitivity and mechanical stability. Simultaneously, BPM insertion length must be minimized to allow lattice designers the greatest freedom in selecting magnet lengths and locations. Envisioned is a conventional four probe arrangement integrated inside of a pair of rf-shielded bellows for mechanical isolation. Basic aspects of the design are presented along with the results of analyses which establish expected mechanical, electronic, and beam physics-related performance measures.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPWI012

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)