IPAC2015 - List of Authors (Hsu, S.Y.)

Paper	Title	Page
MOPTY074	Preliminary Beam Test of Synchrotron Radiation Monitoring System at Taiwan Photon Source	1109
	C.Y. Liao, Y.-S. Cheng, J. -Y. Chuang, K.T. Hsu, S.Y. Hsu, H.P. Hsueh, K.H. Hu, C.K. Kuan, C.Y. Wu NSRRC, Hsinchu, Taiwan
	Taiwan Photon Source (TPS) is a third generation 3 GeV synchrotron light facility. The synchrotron radiation from a dipole can be used to observe the beam parameters. The synchrotron radiation monitor (SRM) systems were designed and implemented for the booster synchrotron and storage ring. The SRM for the booster synchrotron can serve to diagnose the energy ramping process. The beam size decreases when the energy increases was observed. In the storage ring, the streak camera was preferred to observe the beam behaviour of the consecutive bunches. The bunch length and longitudinal instability were observed. The preliminary beam test results are summarized in this report.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPTY074
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPTY077	Control Interface of Pulse Magnet Power Supply for TPS Project	1120
	C.Y. Wu, J. Chen, Y.-S. Cheng, C.-S. Fann, K.T. Hsu, S.Y. Hsu, K.H. Hu, C.H. Huang, D. Lee, C.Y. Liao, K.-K. Lin NSRRC, Hsinchu, Taiwan
	The TPS (Taiwan Photon Source) is low emittance 3 GeV synchrotron light source. The design and implementation of a pulse magnet power supply control system for beam injection and extraction were done. The EPICS embedded programmable logic controller (PLC) was applied to control pulse magnet power supply. The system comprises various input/output modules and a CPU module with built-in Ethernet interface. The control information (status of the power supply, ON, OFF, warn up, reset, reading/setting voltage, etc.) can be accessed remotely using EPICS client tools. The TPS timing system provide trigger signals for pulse magnet power supplies. The Ethernet-based oscilloscope is employed to observe current waveform of pulse magnet power supply with EPICS support. This paper describes control interface and operation GUI for the TPS pulse magnet power supply.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPTY077
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPJE049	TPS Linac Relocation and Beam Test of the LTB Transfer Line	1731
	H.-P. Chang, A.Y. Chen, C.L. Chen, Y.-S. Cheng, C.-S. Fann, K.T. Hsu, S.Y. Hsu, K.-K. Lin, Y.C. Lin, J. Liu, K.L. Tsai NSRRC, Hsinchu, Taiwan
	The Taiwan Photon Source (TPS) 150 MeV linac has been relocated from its 2011 test site to the TPS linac tunnel in 2014. After functional test of the linac hardware modules, the beam parameters were carefully examined at a 31-degree bend diagnostic beam line LTD (linac to beam dump) and compared with previous results. Then, the 150 MeV electron beam was delivered to the linac to booster transfer line (LTB) for beam commissioning. The beam optics matching at both the LTB entrance (i.e. linac exit) and the LTB exit (i.e. injection point of booster) was performed for injection optimization purpose. The LTB lattice setting was verified in the beam steering through LTD and LTB with the help of diagnostics tools such as beam profile monitors (SM) and beam position monitors (BPM). The overall performance of the linac and LTB will be described in this report. #peace@nsrrc.org.tw
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-TUPJE049
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPHA035	Development of an IGBT Pulser for TPS LTB Kicker	3191
	C.L. Chen, H.-P. Chang, Y.-S. Cheng, C.-S. Fann, K.T. Hsu, S.Y. Hsu, K.-K. Lin, K.L. Tsai NSRRC, Hsinchu, Taiwan
	The TPS LTB injection kicker was first commissioned using PFN pulser equipped with thyratron switch. Although its bench-testing results fulfilled the specifications but the performance was degraded due to unavoidable integration difficulty. After evaluating a couple of improvement options in hand, a pulser using IGBT switch was chosen for off-the-bench beneficial purpose. The upgraded pulser satisfies the overall specifications with comfortable margins. Some major performance parameters such as flattop and tail ringing are emphasized concerning their influence on beam injection. This report describes the field-testing result of this IGBT pulser.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-WEPHA035
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Preliminary Beam Test of Synchrotron Radiation Monitoring System at Taiwan Photon Source

1109

C.Y. Liao, Y.-S. Cheng, J. -Y. Chuang, K.T. Hsu, S.Y. Hsu, H.P. Hsueh, K.H. Hu, C.K. Kuan, C.Y. Wu
NSRRC, Hsinchu, Taiwan

Taiwan Photon Source (TPS) is a third generation 3 GeV synchrotron light facility. The synchrotron radiation from a dipole can be used to observe the beam parameters. The synchrotron radiation monitor (SRM) systems were designed and implemented for the booster synchrotron and storage ring. The SRM for the booster synchrotron can serve to diagnose the energy ramping process. The beam size decreases when the energy increases was observed. In the storage ring, the streak camera was preferred to observe the beam behaviour of the consecutive bunches. The bunch length and longitudinal instability were observed. The preliminary beam test results are summarized in this report.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPTY074

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPTY077

Control Interface of Pulse Magnet Power Supply for TPS Project

1120

C.Y. Wu, J. Chen, Y.-S. Cheng, C.-S. Fann, K.T. Hsu, S.Y. Hsu, K.H. Hu, C.H. Huang, D. Lee, C.Y. Liao, K.-K. Lin
NSRRC, Hsinchu, Taiwan

The TPS (Taiwan Photon Source) is low emittance 3 GeV synchrotron light source. The design and implementation of a pulse magnet power supply control system for beam injection and extraction were done. The EPICS embedded programmable logic controller (PLC) was applied to control pulse magnet power supply. The system comprises various input/output modules and a CPU module with built-in Ethernet interface. The control information (status of the power supply, ON, OFF, warn up, reset, reading/setting voltage, etc.) can be accessed remotely using EPICS client tools. The TPS timing system provide trigger signals for pulse magnet power supplies. The Ethernet-based oscilloscope is employed to observe current waveform of pulse magnet power supply with EPICS support. This paper describes control interface and operation GUI for the TPS pulse magnet power supply.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-MOPTY077

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPJE049

TPS Linac Relocation and Beam Test of the LTB Transfer Line

1731

H.-P. Chang, A.Y. Chen, C.L. Chen, Y.-S. Cheng, C.-S. Fann, K.T. Hsu, S.Y. Hsu, K.-K. Lin, Y.C. Lin, J. Liu, K.L. Tsai
NSRRC, Hsinchu, Taiwan

The Taiwan Photon Source (TPS) 150 MeV linac has been relocated from its 2011 test site to the TPS linac tunnel in 2014. After functional test of the linac hardware modules, the beam parameters were carefully examined at a 31-degree bend diagnostic beam line LTD (linac to beam dump) and compared with previous results. Then, the 150 MeV electron beam was delivered to the linac to booster transfer line (LTB) for beam commissioning. The beam optics matching at both the LTB entrance (i.e. linac exit) and the LTB exit (i.e. injection point of booster) was performed for injection optimization purpose. The LTB lattice setting was verified in the beam steering through LTD and LTB with the help of diagnostics tools such as beam profile monitors (SM) and beam position monitors (BPM). The overall performance of the linac and LTB will be described in this report.
#peace@nsrrc.org.tw

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-TUPJE049

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPHA035

Development of an IGBT Pulser for TPS LTB Kicker

3191

C.L. Chen, H.-P. Chang, Y.-S. Cheng, C.-S. Fann, K.T. Hsu, S.Y. Hsu, K.-K. Lin, K.L. Tsai
NSRRC, Hsinchu, Taiwan

The TPS LTB injection kicker was first commissioned using PFN pulser equipped with thyratron switch. Although its bench-testing results fulfilled the specifications but the performance was degraded due to unavoidable integration difficulty. After evaluating a couple of improvement options in hand, a pulser using IGBT switch was chosen for off-the-bench beneficial purpose. The upgraded pulser satisfies the overall specifications with comfortable margins. Some major performance parameters such as flattop and tail ringing are emphasized concerning their influence on beam injection. This report describes the field-testing result of this IGBT pulser.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2015-WEPHA035

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)